Wyszukiwarka
Filtry
wszystkich: 6810
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: LOW-TEMPERATURE OXIDATION
-
JOURNAL OF LOW TEMPERATURE PHYSICS
Czasopisma -
Low-temperature high-pressure cryogelation of nanooxides
Publikacja -
Low temperature luminescence of KMgF3:Eu2+ crystal
Publikacja -
Pre-oxidation of porous ferritic Fe22Cr alloys for lifespan extension at high-temperature
PublikacjaPre-oxidation of porous ferritic Fe22Cr alloys was extensively studied in this paper. Weight gain measurements and SEM analysis revealed that pre-oxidation performed at 900◦C for 40 min increased the lifespan of the alloy. A Cr evaporation study did not disclose any significant influence of the pre-oxidation process on the Cr content in the alloy. For a more detailed assessment, TEM imaging and X-ray tomography measurements of...
-
High temperature oxidation of porous alloys for solid oxide fuel cell applications
PublikacjaW pracy proszki PI600, 317L i 430L stali użyto do przygotowania porowatych metalowych podłoży dla tlenkowych ogniw paliwowych. Po spiekaniu w różnych temperaturach oceniana była ich porowatość i wysokotemperaturową odporność na korozję. Cykliczna analiza termograwimetryczna, dyfraktometria rentgenowska i obrazów SEM były używane do opisu właściwości tych porowatych stopów. Właściwości elektryczne badano dla wybranych próbek. Wpływ...
-
Comparison of different advanced oxidation processes for the degradation of room temperature ionic liquids
PublikacjaZbadano możliwość zastosowania wybranych zaawansowanych technologii utleniania (UV, UV/H2O2, UV/TiO2) do degradacji cieczy jonowych. Do degradacji wytypowano pięć związków: HHiM, BMiM, MiM, OMiM oraz EEiM.
-
LOW TEMPERATURE PHYSICS
Czasopisma -
Evaluation of Low Temperature Properties of Rubberized Asphalt Mixtures
PublikacjaThe paper presents low-temperature test results of asphalt mixtures designed with use of bitumen modified by crumb rubber and also SBS polymer. Laboratory tests were conducted on two types of asphalt mixtures for wearing course – stone matrix asphalt (SMA 8) and porous asphalt (PA 8). This paper presents results of the following laboratory tests at low temperatures: TSRST test, three point bending creep test, fracture toughness...
-
Criteria for selection of working fluid in low-temperature ORC
PublikacjaThe economics of an ORC system is strictly linked to thermodynamic properties of the working fluid. A bad choice of working fluid could lead to a less efficient and expensive plant/generation unit. Some selection criteria have been put forward by various authors, incorporating thermodynamic properties, provided in literature but these do not have a general character. In the paper a simple analysis has been carried out which resulted...
-
Influence of High Temperature Oxidation on Hydrogen Absorption and Degradation of Zircaloy-2 and Zr 700 Alloys
PublikacjaThe present research was aimed at determining the effects of the oxide layers on hydrogen absorption, microstructure and mechanical properties of the Zircaloy- 2 and Zr 702 alloys. The oxidation was made at 350 °C, 700 °C and 900 °C for 10 to 30 min in laboratory air, followed by hydrogen cathodic charging for 72 h and annealing at 400 °C for 4 h. The slow strain rate tests were carried out on oxidized, charged and annealed specimens. The...
-
High temperature oxidation behavior of SUS430 SOFC interconnects with Mn-Co spinel coating in air
PublikacjaIn this study, SUS430 alloy is evaluated for its high temperature corrosion properties as a possible material for interconnects of solid oxide fuel cells (SOFCs). Samples are coated with Mn-Co by commercial physical vapor deposition (PVD) process and oxidized in air for 1250 h at 800 °C. A dense cubic Mn-Co-Fe spinel layer is formed on the surface, showing great effect on corrosion reduction compared with the samples without coating....
-
Utilisation of bleed steam heat to increase the upper heat source temperature in low-temperature ORC
PublikacjaW pracy przedstawiono możliwość dogrzewu obiegu ORC za pomocą pary upustowej.
-
High-Temperature Oxidation of Heavy Boron-Doped Diamond Electrodes: Microstructural and Electrochemical Performance Modification
PublikacjaIn this work, we reveal in detail the effects of high-temperature treatment in air at 600 °C on the microstructure as well as the physico-chemical and electrochemical properties of boron-doped diamond (BDD) electrodes. The thermal treatment of freshly grown BDD electrodes was applied, resulting in permanent structural modifications of surface depending on the exposure time. High temperature affects material corrosion, inducing...
-
Impact of low-temperature sintering on the Fe-based amorphous coatings
PublikacjaBulk metallic glasses (BMGs) have gained a lot of attention in recent years due to their outstanding properties such as high hardness and excellent wear and corrosion resistance. However, they are restricted in industrial applications due to their extreme brittleness. Iron based amorphous coatings from BMGs are the best solution to use them by overcoming the problem of extreme brittleness. The coatings can be sprayed by various...
-
Proton Conducting Ceramic Powder Synthesis by a Low Temperature Method
PublikacjaMolten salt synthesis (MSS) is a simple method for the preparation of ceramic powders with specific morphology. The main role of the molten salts is to increase the reaction rate and lower the reaction temperature. It occurs because of much higher mobility of reactants in the liquid medium than in the solid state. In this work the molten salt synthesis was applied to produce ceramic powders of La0995Ca0005NbO4 and BaCe09−xZrxY01O3....
-
Low-temperature spectroscopic and scintillation characterisation of Ti-doped Al2O3
Publikacja -
Low-temperature synthesis of silicon carbide powder using shungite
Publikacja -
Fiber-optic temperature sensor using low-coherence interferometry
Publikacja -
Low-temperature reactivity of the surface species of vanadia–tungsta catalyst
Publikacja -
Mitigation of Membrane Wetting by Applying a Low Temperature Membrane Distillation
Publikacja -
Low-temperature processing of thin-film electrolyte for electrochemical devices.
PublikacjaPrzygowanie filmów elektrolitu jest jednym z najbardziej istotnych procesów technologicznych wytworzenia urządzeń elektrochemicznych takich jak ogniwa paliwowe. Zmniejszenie grubości filmu jest powiązane ze zmniejszeniem rezystancji elektrolitu, co bardzo korzystnie wpływa na wydajność ogniw paliwowych. W pracy tej przedstawiono niskotemperaturową (<1000C) metodę wytwarzenia filmów elektrolitu z tlenku cyrkonu stabilizowanego itrem...
-
Low-temperature processed anode for Solid Oxide Fuel Cells
PublikacjaPrzygotowano i przebadano kompozytową anode Ni/YSZ, która została przygotowana z wykorzystaniem technologii net shape. Wyniki potwierdziły, że kompozyt może być wykorzystany jako potencjalna anoda w tlenkowych ogniwach paliwowych.
-
Influence of the low ambient temperature on the start-up process of hydraulic pumps
PublikacjaStarting hydraulic pumps in low ambient temperatures may cause: decreased hydraulic-mechanical efficiency, larger vibration of hydraulic installation, faster wear and more frequent damage to the elements of pumps, change of material properties of elements, increase of pressure drop. As a result of pressure drop in the suction pipe, large underpressure may be experienced, causing incomplete filling of pump working chambers with...
-
Low temperature rotary Stirling engine: conceptual design and theoretical analysis
PublikacjaThe use of low-temperature energy sources for electricity generation demands a dual focus: a substantial enhancement in the efficiency of energy conversion devices and a reduction in system production costs. Particularly in scenarios where low-temperature energy sources are scarce, this factor can be pivotal in facilitating widespread adoption of such technologies. The Stirling engine emerges as a promising solution capable of...
-
Analysing selection of low-temperature medium for cogeneration micro power plant
PublikacjaThe article analyses the ORC system working with dry and wet low-boiling media which are most frequently used in installations of this type. Two types of cycles were examined, which were the cycle with heat regeneration for dry media: fc72, hfe7100, R227ea, R245fa, R423a and R600a, and the cycle without heat regeneration for wet media: R11, R12, R134a, R718 and 507a. The calculations were performed for the assumed required thermal...
-
Analysing selection of low-temperature medium for cogeneration micro power plant
PublikacjaThe article analyses the ORC system working with dry and wet low-boiling media which are most frequently used in installations of this type. Two types of cycles were examined, which were the cycle with heat regeneration for dry media: fc72, hfe7100, R227ea, R245fa, R423a and R600a, and the cycle without heat regeneration for wet media: R11, R12, R134a, R718 and 507a. The calculations were performed for the assumed required thermal...
-
Low-Temperature Requirements for Bitumen in Central East European Road Construction
PublikacjaThe paper presents the proposition of special assessment of lowtemperature requirements for bitumens in the region of Central and Eastern Europe where there is a moderate transitional area from sea to the continental type of climate. The results of the research program conducted on the road neat bitumens, Styrene-Butadiene-Styrene polymer and polymer-rubber modified bitumen, and multigrade bitumen types were presented and discussed....
-
Testing of low temperature behaviour of asphalt mixtures in bending creep test
PublikacjaThe paper presents a method of bending beam test and its importance for evaluation of asphalt mixtures behaviour at low temperatures. Two types of asphalt mixtures: asphalt concrete AC with normal paving grade bitumen and stone mastic asphalt SMA with SBS-modified bitumen were tested. Long-term oven ageing (LTOA) test was also used in the laboratory according to SHRP procedure. The Burgers model was applied and rheological parameters...
-
Low temperature broad band dielectric spectroscopy of multiferroic Bi6Fe2Ti3O18 ceramics
PublikacjaIn the present research the tool of broadband dielectric spectroscopy was utilized to characterize dielectric behavior of Bi6Fe2Ti3O18 (BFTO) Aurivillius-type multiferroic ceramics. Dielectric response of BFTO ceramics was studied in the frequency domain (Δν=0.1Hz – 10MHz) within the temperature range ΔT=-100°C – 200°C. The Kramers-Kronig data validation test was employed to validate the impedance data measurements and it was found...
-
Boron-Doped Diamond/GaN Heterojunction—The Influence of the Low-Temperature Deposition
PublikacjaWe report a method of growing a boron-doped diamond film by plasma-assisted chemical vapour deposition utilizing a pre-treatment of GaN substrate to give a high density of nucleation. CVD diamond was deposited on GaN substrate grown epitaxially via the molecular-beam epitaxy process. To obtain a continuous diamond film with the presence of well-developed grains, the GaN substrates are exposed to hydrogen plasma prior to deposition....
-
Comprehensive analysis of low-temperature methods for reclaiming of ground tire rubber
PublikacjaManagement of waste tires has become an important topic for decades. The lack of an effective method to manage the materials as mentioned above leads to illegal landfills. This problematic waste can be divided into two main categories depending on the physical condition of the waste: (i) partially used tires; (ii) end-of-life tires. While the first group can be reused or retreaded, the second group requires special measures to...
-
Low-temperature air plasma modification of chitosan-coated PEEK biomaterials
Publikacja -
Effect of low-temperature plasma on chitosan-coated PEEK polymer characteristics
Publikacja -
Novel catalysts for low temperature synthesis of single wall carbon nanotubes
Publikacja -
Grouts with highly thermally conductive binder for low-temperature geothermal applications
Publikacja -
Growth Enhancement of Radish Seed Induced by Low-Temperature Argon Plasma
Publikacja -
Regulation of replication of λ phage and λ plasmid DNAs at low temperature
Publikacja -
High temperature corrosion of evaporator tubes in low-emission steam boilers
PublikacjaW artykule opisano zjawisko korozji wysokotemperaturowej rur ekranowych kotłów parowych niskoemisyjnych. Przeprowadzono badania rur po eksploatacji. Wykonano badania składu chemicznego zgorzelin. Stwierdzono, że główną przyczyną pocienienia rur na wyższych poziomach jest korozja siarkowa, natomiast na poziomach niższych oddziaływanie stopionych soli.
-
Metal Oxides and Low Temperature SWCNT Synthesis via Laser Evaporation
Publikacja -
Electrochemical oxidation of PFOA and PFOS in landfill leachates at low and highly boron-doped diamond electrodes
PublikacjaPolyfluorinated alkyl substances (PFASs) may reach landfill leachates (LLs) due to improper waste management. In this study perfluorooctanoate (PFOA) and perfluorooctane sulphonate (PFOS) were used as representatives of PFASs in the decomposition on boron-doped diamond electrodes (BDDs) with high (10k ppm) and low (0.5k ppm) boron doping concentrations. The result shows that although better COD removal efficacies are obtained on...
-
The Studies on α-Pinene Oxidation over the TS-1. The Influence of the Temperature, Reaction Time, Titanium and Catalyst Content
Publikacja -
Field Evaluation of High Modulus Asphalt Concrete Resistance to Low-Temperature Cracking
PublikacjaHigh-modulus asphalt concrete has numerous advantages in comparison to conventional asphalt concrete, including increased resistance to permanent deformations and increased pavement fatigue life. However, previous studies have shown that the construction of road pavements with High Modulus Asphalt Concrete (HMAC) may significantly increase the risk of low-temperature cracking. Those observations were the motivation for the research...
-
Evaluation of Asphalt Mixture Low-Temperature Performance in Bending Beam Creep Test
PublikacjaLow-temperature cracking is one of the most common road pavement distress types in Poland. While bitumen performance can be evaluated in detail using bending beam rheometer (BBR) or dynamic shear rheometer (DSR) tests, none of the normalized test methods gives a comprehensive representation of low-temperature performance of the asphalt mixtures. This article presents the Bending Beam Creep test performed at temperatures from −20...
-
Influence of cooling rate and additives on low-temperature properties of asphalt mixtures in the TSRST
PublikacjaThe paper presents the results and analysis of low-temperature properties of asphalt mixtures according to Thermal Stress Restrained Specimen Test (TSRST) and Indirect Tensile Test methods. Different groups of bitumen were investigated: neat, SBS-modified and highly SBS-modified. Influence of cooling rates (1 C/h, 3 C/h, 5 C/h and 10 C/h) and additives (aramid fibres and crumb rubber) was identified as well. Moreover, for each...
-
Impact of the type of heat exchanger on the characteristics of low-temperature thermoacoustic heat engines
PublikacjaThermoacoustic technologies are considered an effective solution for harnessing low-temperature heat, whether from waste or renewable sources. However, in practice, developing and implementing high-performance ther- moacoustic systems is a complex challenge. In real waste heat recovery systems, heat exchange between ther- moacoustic engines (TAEs) and external heat sources is facilitated by auxiliary systems, such as circulation...
-
Management of low-temperature heat source by ORC aided by additional heat source
PublikacjaThe presented work is aimed at utilisation of waste heat in the manner to produce electricity in ORC installation. Therefore the precondition of the study was to use the waste heat available in the form of a stream of hot water at 90°C. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. That was the incentive to search for the ways of increasing the temperature of the...
-
Management of low-temperature heat source by ORC aided by additional heat source
PublikacjaIn the paper presented is a concept to utilize waste heat from the power plant with the aid of the low-temperature ORC cycle. The ORC system is heated from two heat sources, the first one being the flow rate of waste heat obtained from the exhaust gases. Subsequently, the working fluid in the cycle is additionally heated by the condensing steam from the low pressure turbine extraction points increasing in such way the level of...
-
Impact of reclaimed asphalt pavement (RAP) on low-temperature properties of asphalt concrete
PublikacjaHot mix recycling is a practice which enables reusing materials from old asphalt pavements. Current Polish regulations allow usage of RAP only for binder and base courses, and its amount is limited. Asphalt mixtures with RAP material have to fulfil requirements stated for typical asphalt mixtures. The research presents low-temperature properties of twelve different asphalt concretes with RAP material, determined using three-point...
-
Performance of the very high-temperature heat pump with low GWP working fluids
PublikacjaTraditional heat pumps are a very attractive pro-ecological solutions for a number of applications, including providing of heating or heat recovery from industrial processes. The application range of heat pumps could be greatly enlarged when the operating temperature would be increased to 130-150°C and/or the temperature lift can be increased to 50-100 K. In the paper, the very high temperature vapour-compressor based single stage...
-
The Impact of Homogeneity of High Modulus Asphalt Concrete Layer on Low-Temperature Cracking
PublikacjaDuring winter season of 2012 numerous transverse cracks developed in high-modulus asphalt concrete (HMAC) base of newly constructed motorway. Pavement cracked both in transverse joint locations and in the area between them. Research which was conducted during investigation of the causes and mechanisms of cracking consisted of: field examination, laboratory testing of specimens cored out of the existing pavement, computational analyses...