Wyszukiwarka
Wyniki wyszukiwania dla: NAVAL TURBINE ENGINES
-
Exhaust gas temperature measurements in diagnostic examination of naval gas turbine engines. Part II. Unsteady processes
PublikacjaThe second part of the article presents the results of operating diagnostic tests of a two- and three-shaft engine with a separate power turbine during the start-up and acceleration of the rotor units. Attention was paid to key importance of the correctness of operation of the automatic engine load control system, the input for which, among other signals, is the rate of increase of the exhaust gas flow temperature. The article...
-
Exhaust gas temperature measurements in diagnostic examination of naval gas turbine engines. Part I: Steady-state processes
PublikacjaThe article presents a possible method of detecting failures in the flow section and supply system of a naval gas turbine engine based on the exhaust gas temperature measured behind the gas generator. This temperature is a basic diagnostic parameter use for evaluating the technical state of the turbine engine in operation, and is monitored during engine start-ups, accelerations and decelerations of rotor units, and steady-load...
-
Exhaust gas temperature measurements in diagnostic examination of naval gas turbine engines. Part III. Diagnostic and operating tolerances
PublikacjaThe third part of the article presents a method for detecting failures of the automatic engine control system with the aid of an exhaust gas temperature setter, specially designed and machined for this purpose. It also presents a procedure of identifying the operating tolerances and determining the diagnostic tolerances for the exhaust gas temperature recorded in the naval turbine engine during the start-up and acceleration processes....
-
Analysis of diagnostic informativeness of the exhaust temperature of a naval gas turbine
PublikacjaThe conducted investigations aimed to carry out an analysis of the possibility that the failures identification in the automatic control system of a gas turbine engine could be worked out on the basis of measurements of the exhaust stream temperature behind the gas generator. The exhaust temperature represents a basic control parameter, enabling technical state evaluation of the engine within the operation process, which is observed...
-
Balancing energy processes in turbine engines
PublikacjaThe article discusses the issue of balancing energy processes in turbine engines in operation in aeronautic and PDULQHSURSXOVLRQV\VWHPVZLWKWKHDLPWRDQDO\VHDQGHYDOXDWH EDVLFRSHUDWLQJSDUDPHWHUV7KH¿UVWSDUWSUHVHQWV the problem of enormous amounts of energy needed for driving fans and compressors of the largest contemporary turbofan engines commonly used in long-distance aviation. The amounts of the transmitted power and the effect RIÀRZSDUDPHWHUVDQGFRQVWUXFWLRQDOSURSHUWLHVRIWKHHQJLQHV RQWKHLUSHUIRUPDQFHDQGUHDOHI¿FLHQF\DUH evaluated....
-
Operation of gas turbine engines as the index of their reliability and safety.
PublikacjaW referacie przedstawiono propozycję ilościowej interpretacji działania turbinowego silnika spalinowego, które (podobnie jak przedstawione w fizyce działania Hamiltona i Maupertiusa oraz działanie wynikające ze zmiany pędu ciała) jest rozpatrywane jako wielkość fizyczna z jednostką miary zwaną dżulosekundą [dżulsekunda]. Wykazano też, że taka interpretacja działania może być uznana za wskaźnik niezawodności, a w szczególnych przypadkach...
-
Diagnostic tolerances' evaluation method of the start-up exhaust temperature of a naval gas turbine
PublikacjaThe conducted investigations aimed to elaborate the method of marking diagnostic tolerances of the exhaust temperature of a gas turbine observed during engine's start-up process. The diagnostic tolerances were determined by means of statistical inference by creating the hypothesis about a normal distribution of the start-up exhaust temperature's dispersion in the initial operation moment, which was subsequently verified applying...
-
Comparing combined gas tubrine/steam turbine and marine low speed piston engine/steam turbine systems in naval applications
PublikacjaPorównano układy napędowe okrętowe kombinowane turbina gazowa- turbina parowa oraz spalinowy okrętowy silnik tłokowy wolnoobrotowy - turbina parowa. Porównywano moce oraz zużycie paliwa oraz parametry pary świeżej układu turbiny parowej.
-
Operation evaluation method for marine turbine combustion engines in terms of energetics
PublikacjaAn evaluation proposal (quantitative determination) of an y combustion turbine engine operation has been presented , wherein the impact energy occurs at a given time due to Energy conversion. The fact has been taken into account that in this type of internal combustion engines the energy conversion occurs first in the combustion chambers and in the spaces between the blade of the turbine engine. It was assumed that in the combustion...
-
Operational causes of fatigue failures within the passages of gas turbine engines
PublikacjaThe short profile of a fatigue wear process of gas turbine engine's constructional elements has been introduced in the article. The primary causes of a fatigue cracks formation within the mechanical system as well as within the passages of the engine have been showed. Especial attention was devoted to the low-cycle fatigue, what is associated with unsteady thermal-flow processes being worked out in the passages.The selected damages...
-
Diagnosing marine turbine engines through energy characteristics of their flow section
PublikacjaThe aim of the performed research was to develop of diagnostic method of the flow section of a marine turbine combustion engine based on the level of delamination of its energy characteristics. The here adopted diagnostic model provides for a formulation of the evaluation of the technical conditions based on the measurements of the parameters of the thermodynamic medium in the characteristic control cross-sections of the engine...
-
Review of Small Gas Turbine Engines and Their Adaptation for Automotive Waste Heat Recovery Systems
Publikacja -
Entropy function application within the selection process of diagnostic parameters of marine diesel and gas turbine engines
PublikacjaThe paper presents the method of conducting an analysis of the diagnostic informativeness among the parameters characterizing the observed gas dynamic processes carried out within working spaces of marine diesel and gas turbine engines. An entropy function, as the measure of uncertainty of the identified states' set of the engine unfitness was applied. Having evaluated the diagnostic information the most adequate parameters were...
-
Feasibility of combined diesel engine - steam turbine in power station operating in the maritime
PublikacjaCompression-ignition engines used in ship technology as main propulsion engines are large units reaching even to 50-60 MW. Currently, the efficiency of such engines amounts to 45-50%. With such a large power unit, exhaust gases leaving the engine contain very large quantities of heat available for further treatment. Exhaust gases from the piston engine contain about 25% of the heat supplied to the engine in the fuel. Using the...
-
The sources of contamination and reasons of damage of the flow part of the marine turbine engine in operation
PublikacjaThe aim of this paperis to show particular sensitivity of the flow part of the marine turbine engine to the presence of contaminations in the intake air. The contaminations form hard-to-remove deposits in the intervene channels that result in a reduced efficiency and performance of the engine. The paper classifies the contaminants according the source of their formation and their destructive force. The performed analyses and syntheses...
-
"Shadow" method application within endoscopic examinations of marine engines
PublikacjaThe paper deals with diagnostic issues concerning endoscopic examinations of the working spaces within marine diesel and gas turbine engines. In the beginning, the endoscopy apparatus being on the laboratory equipment of the Department of Ship Power Plants of Gdansk University of Technology in Poland has been characterized. The endoscopy considerations have been focused on theoretical bases of a digital image processing and especially...
-
"Shadow" method application within endoscopic examinations of marine engines
PublikacjaThe paper deals with diagnostic issues concerning endoscopic examinations of the working spaces within marine diesel and gas turbine engines. In the beginning, the endoscopy apparatus being on the laboratory equipment of the Department of Ship Power Plants of Gdansk University of Technology in Poland has been characterized. The endoscopy considerations have been focused on theoretical bases of a digital image processing and especially...
-
Application of Thermo-chemical Technologies for Conversion of Associated Gas in Diesel-Gas Turbine Installations for Oil and Gas Floating Units
PublikacjaThe paper considers the issue of thermo-chemical recovery of engine’s waste heat and its further use for steam conversion of the associated gas for oil and gas floating units. The characteristics of the associated gas are presented, and problems of its application in dual-fuel medium-speed internal combustion engines are discussed. Various variants of combined diesel-gas turbine power plant with thermo-chemical heat recovery are...
-
Rozpoznawanie uszkodzeń w części przepływowej okrętowego turbinowego silnika spalinowego na podstawie wyników badania endoskopowego = Failures' recognising within the passages of a marine gas turbine engine on the basis of results of endoscopic investigation
PublikacjaThe paper deals with diagnostic issues concerning endoscopic examinations of marine gas turbine engines. There will be presented selected information about failures within the passages and accessible endoscopic methods and means enabling their detection. The author focuses on the endoscopic techniques and widely presents the possibilities of this quickly developed diagnostic method. There will be also presented representative results...
-
Possibility to use engine compression ignition engines in floating power plants marine
PublikacjaCompression-ignition engines used in ship technology as main propulsion engines are large units reaching even to 50-60 MW. The engines can be used in power industry for electricity generation in a simple or combined steam turbine system in combined heat and power plants. The leading engine in such an arrangement is an internal-combustion piston engine. The main propulsion engines are used in large piston internal-combustion engines...
-
Inlet air fogging of marine gas turbine in power output loss compensation
PublikacjaThe use of inlet air fogging installation to boost the power for gas turbine engines is widely applied in the power generation sector. The application of fogging to mechanical drive is rarely considered in the literature [1]. This paper will cover some considerations relating to its application to gas turbines in ship drive. There is an important evaporative cooling potential throughout the world when the dynamic data is evaluated,...
-
Alternative diagnostic method applied on marine diesel engines having limited monitoring susceptibility
PublikacjaThe paper presents a method of technical state evaluation of working spaces of a marine diesel engine at the limited control susceptibility. The method foresees making a diagnosis of the engine's working spaces on the basis of measurements of the exhaust gas pressure in the channels connecting engine cylinders with the turbocharger's turbine. Diagnostic measurements are carried out at representative (comparative) steady loads depending...
-
Alternative diagnostic method applied on marine diesel engines having limited monitoring susceptibility
PublikacjaThe paper presents a method of technical state evaluation of working spaces of a marine diesel engine at the limited control susceptibility. The method foresees making a diagnosis of the engine's working spaces on the basis of measurements of the exhaust gas pressure in the channels connecting engine cylinders with the turbocharger's turbine. Diagnostic measurements are carried out at representative (comparative) steady loads depending...
-
The thermal effort during marine steam turbine flooding with water
PublikacjaThe work discussed an extreme case of cooling a steam turbine. The ship's steam turbine was used as an example. In marine transport units with low-speed engines dominate, however, there are also units with steam turbines. An example of analysed marine steam turbine is shown in Fig. 1. When considering the issue of cooling steam turbines, it is necessary to estimate the extreme conditions that may occur during operation of the turbine....
-
“Shadow” vs. “Phase 3D” method within endoscopic examinations of marine engines
PublikacjaA visual investigation of surfaces creating internal, working spaces of marine combustion engines by means of specialized view-finders so called endoscopes is at present almost a basic method of technical diag-nostics. The surface structure of constructional material is visible during investigations like through the magnifying glass (usually with a precisely determined magnification), which makes possible a detection, recognition...
-
SELECTED COMBINED POWER SYSTEMS CONSISTED OF SELFIGNITION ENGINE AND STEAM TURBINE
PublikacjaThis paper presents optimization of selected combined diesel engine-steam turbine systems. Two systems: the system combined with waste heat one-pressure boiler only and its version containing additionally low-pressure boiler proper feeding degasifier and the system of two-pressure cycle, were taken into considerations. Their surplus values of power output and efficiency associated with utilization of waste heat contained in piston...
-
Investigation of the Combustion Processes in the Gas Turbine Module of an FPSO Operating on Associated Gas Conversion Products
PublikacjaIn this paper, we consider the issue of thermo-chemical heat recovery of waste heat from gas turbine engines for the steam conversion of associated gas for offshore vessels. Current trends in the development of offshore infrastructure are identified, and the composition of power plants for mobile offshore drilling units and FPSO vessels is analyzed. We present the results of a comparison of power-to-volume ratio, power-to-weight...
-
Investigation of ecological parameters of a gas turbine combustion chamber with steam injection for the floating production, storage, and offloading vessel
PublikacjaThe article is dedicated to the investigation of the possibility of using the contact type gas turbine cycle with steam injection into the combustion chamber for the floating production, storage, and offloading vessel in order to increase the specific power and efficiency and reduce emissions of toxic components. A new approach is proposed, associated with the use of the two-stage injection of superheated steam into a gas turbine...
-
Investigation of the Efficiency of a Dual-Fuel Gas Turbine Combustion Chamber with a Plasma‒Chemical Element
PublikacjaThe study is devoted to the possibility of increasing the efficiency of the working process in dual-fuel combustion chambers of gas turbine engines for FPSO vessels. For the first time, it is proposed to use the advantages of plasma‒chemical intensification of the combustion of hydrocarbon fuels in the dual-fuel combustion chambers, which can simultaneously operate on gaseous and liquid fuels. A design scheme of a combustion chamber...
-
INVESTIGATION OF THE CHARACTERISTICS OF A LOWEMISSION GAS TURBINE COMBUSTION CHAMBER OPERATING ON A MIXTURE OF NATURAL GAS AND HYDROGEN
PublikacjaT his article is devoted to the investigation of the characteristics of a low-emission gas turbine combustion chamber, which can be used in Floating Production, Storage and Offloading (FPSO) vessels and operates on a mixture of natural gas and hydrogen. A new approach is proposed for modelling the processes of burning out a mixture of natural gas with hydrogen under preliminary mixing conditions in gaseous fuel with an oxidizer...
-
Exhaust gas temperature measurements in diagnostics of turbocharged marine internal combustion engines. Part I. Standard measurements.
PublikacjaThe article discusses the problem of diagnostic informativeness of exhaust gas temperature measurements in turbocharged marine internal combustion engines. Theoretical principles of the process of exhaust gas flow in turbocharger inlet channels are analysed in its dynamic and energetic aspects. Diagnostic parameters are defined which enable to formulate general evaluation of technical condition of the engine based on standard...
-
Combustion Engines
Czasopisma -
Analysing the potential for application of the phase shift method in endoscopic examination of marine engines
PublikacjaThe article presents theoretical principles of image processing in digital endoscopy which makes use of a miniaturised spectral scanner “PhaseProbe” designed by General Inspection Technologies LP, the producer of the measuring videoendoscope Everest XLG3. The technology of optoelectronic 3D mapping of the examined surface, which consists in measuring the phase shift between the emitted and reflected light waves, is briefly described....
-
A comparative study of pentanol (C5 alcohol) and kerosene blends in terms of gas turbine engine performance and exhaust gas emission
PublikacjaThe growing demand for sustainable and clean energy sources provides the incentive for the development of alternative fuels. Simultaneously, the development of gas turbine technologies with flexible fuel supply systems enables the use of alternative non-fossil fuels that can play key roles in contributing to global efforts in meeting emissions targets. This paper presents the current state of knowledge on the production and potential...
-
Evaluation of working spaces' technical condition of marine diesel engine on the basis of operation research
PublikacjaThe paper presents the method of evaluation of the technical state of working spaces of a marine diesel engine at the reduced control susceptibility. The method foresees making diagnosis on the basis of the measurements of exhaust gas pressure in the channels connecting engine cylinders with turbocharger's turbine. In the beginning of the article the research objects are characterized i.e. ZVIEZDA main engine of M401 type and the...
-
Suitableness of SLM Manufactured Turbine Blade for Aerodynamical Tests
PublikacjasettingsOrder Article Reprints Open AccessArticle Suitableness of SLM Manufactured Turbine Blade for Aerodynamical Tests by Janusz Telega 1,*ORCID,Piotr Kaczynski 1ORCID,Małgorzata A. Śmiałek 2ORCID,Piotr Pawlowski 3ORCID andRyszard Szwaba 1ORCID 1 Institute of Fluid Flow Machinery Polish Academy of Sciences (IMP PAN), Fiszera 14, 80-231 Gdansk, Poland 2 Faculty of Mechanical Engineering and Ship Technology, Institute of Naval...
-
Diagnostyka eksploatacyjna okrętowych silników spalinowych - tłokowych i turbinowych
PublikacjaW monografii przedstawiono wybrane zagadnienia diagnostyki technicznej silników spalinowych dużej mocy, zarówno tłokowych, jak i turbinowych, ukierunkowane na eksploatację okrętowych (i nie tylko) systemów energetycznych, w których występują tego typu silniki. W początkowej części opracowania zaproponowano koncepcję systemowego ujęcia diagnostyki eksploatacyjnej silników okrętowych w aspekcie obowiązujących standardów światowych...
-
ISSUES OF ECONOMIC ANALYSIS OF ELECTRIC ENERGY GENERATION IN A FLOATING POWER PLANT
PublikacjaThis article presents basic dependences for conducting a technical and economic analysis related with investment projects. It describes a combined system of a compression ignition engine and a steam turbine, whose aim, when placed on a floating platform, is to generate electric energy in the so-called distributed generation system. Such a system involves a reciprocating internal combustion engine and a connected steam turbine system...
-
Stability evaluation of the marine propulsion unit mechanical system bymeans of vibrations measurements and their analysis.
PublikacjaIn paper selected issues concerning vibration diagnosis of the mechanical system within marine propulsion units have been given. The analysis of vibration parameters was carried out on the basis of experimental examinations of a real object in which an exceedance of the allowable vibration's level had been observed. In the beginning, the vibration apparatus being on laboratory equipment of the Department of Ship Power Plants of...
-
Stability evaluation of the marine propulsion unit's mechanical system by means of vibration measurements and their analysis
PublikacjaIn this paper selected issues concerning vibration diagnosis of the mechanical system within marine propulsion units have been given. The analysis of vibration parameters was carried out on the basis of experimental examinations of a real object in which an exceedance of the allowable vibration's level had been observed. In the beginning, the vibration apparatus being on laboratory equipment of the Department of Ship Power Plants...
-
Naval mine detection system based of FPGA circuit
PublikacjaElectrochemical processes take place in a metal object immersed into sea water even if an anticorrosive coating is applied [1]. As a result, flowing field appears around the object. There are naval mines between many other objects situated in the sea. Naval mines can be put in the seabed in order to be more difficult to detect by sonars. Such a mine is located on the line demarking two environments of different electrical conductivity....
-
Analysis of balancing of four stroke V6 engines
PublikacjaAnalysis of balance of V6 engines with a common-pin crankshaft depending on a cylinder bank angle and the crank radius to connecting rod length ratios , based on the relations derived, is presented in the paper. The bank angles providing the lowest moment of inertia forces in reciprocating motion, for selected values, were determined. The position of the plane of the main counterweights in order to maximum balance of the moment...
-
Reverberation chamber in emc tests of naval systems
PublikacjaPaper covers the techniques of emission and immunity testing to the electromagnetic field in reverberation chamber. The procedure of he chamber calibration and field homogeneity assessment were covered. The naval forces' product as selected as an example for discussing the testing procedure in the chamber. The paper's summary gives the assortment of methodology in radiation emission testing and immunity to the electromagnetic field...
-
In Search of Naval Beauty. Historical Study of Ship Architecture
PublikacjaDesigning ships is no mean achievement. In the old days, constructors focused on making their ships visually appealing, while paying scant regard to the living conditions of the crew. Such an approach reflected the state of the art in ship building at the time as well as the social order prevalent in those days. A breakthrough came no earlier than at the turn of the 19th / 20th centuries. The industrial revolution brought along...
-
Comparative analysis of balancing of V6 engines with common- and split-pin crankshafts
PublikacjaAn analysis of balancing of V6 engines equipped with split-pin crankshafts with any cylinder bank angle based on the mathematical relations derived in the paper was carried out. A comparison of the quality of their balancing with engines equipped with common-pin crankshafts was also carried out. The bank angle ranges beneficial for balancing of moments of inertia forces in reciprocating motion were determined. A mathematical relation...
-
DME as alternative fuel for compression ignition engines – a review
PublikacjaThe ecological issues and the depletion of crude oil, has led the researchers to seeking for non-petroleum based alternative fuels, along with more advanced combustion technologies, and after-treatment systems. The use of clean alternative fuels is the one of the most perspective method that aiming at resolving of the said issues. One of the promising alternative fuels that can be used as a clean highefficiency compression ignition...
-
Stirling engines - the state of technology development and computational models
PublikacjaStirling engines represent a technologically important solution in combined heat and power systems. Their use enables the achievement of over 90 percent efficiency in the management of the primary energy source with a very high durability of the device, mainly due to the lack of contact of the working gas with external factors and a very small number of mechanical components. The use of a Stirling engine may be equally important...
-
Thermodynamic modeling of combustion process of the internal combustion engines – an overview
PublikacjaThe mathematical description of combustion process in the internal combustion engines is a very difficult task, due to the variety of phenomena that occurring in the engine from the moment when the fuel-air mixture ignites up to the moment when intake and exhaust valves beginning open. Modeling of the combustion process plays an important role in the engine simulation, which allows to predict incylinder pressure during the combustion,...
-
Selection of drive engines for dredge pumps
PublikacjaThis paper presents the principles of selecting drive engines for dredge pumps, formulated by this author. In order to formulate them influence of drive engines on dredge pump characteristics and dredger effectiveness, have been analyzed. Also, an analysis of results of the author's operational investigations concerning energy consumption and parameters of excavated soil transport on board dredgers has been performed.
-
Mohammad Hossein Ghaemi dr inż.
OsobyMohammad Hossein Ghaemi (ur. 1967), adiunkt Wydziału Oceanotechniki i Okrętownictwa (WOiO) PG w Katedrze Automatyki i Energetyki. Jest absolwentem Uniwersytetu Teherańskiego z zakresu mechaniki ciała stałego, a także PG na kierunku Oceanotechnika. Uzyskał stopień doktora nauk technicznych na PG w 2004 roku. Od 1995 roku pracuje na WIMiO PG (do 2020 r. WOiO PG) i prowadzi zajęcia dydaktyczne i badania naukowe w zakresie automatyki...