Wyszukiwarka
Filtry
wszystkich: 1507
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: GRAPHENE HYDROGEL
-
SEI Growth and Depth Profiling on ZFO Electrodes by Soft X-Ray Absorption Spectroscopy
PublikacjaZnFe2O4 (ZFO) Li-ion batteries (LIBs) represent a reliable, affordable, and safe energy storage technology for use in portable application. However, current LIB active materials (graphite, lithium/transition metal spinel or layered oxides, olivine structures) can store only limited energy since they rely on insertion storage based on solid-state host-guest interactions. Moreover, performances and durability of the cells are strongly...
-
Imidazole-Based Lithium Salt LiHDI as a Solid Electrolyte Interphase-Stabilising Additive for Lithium-Conducting Electrolytes
PublikacjaLithium salt LiHDI (lithium 4,5-dicyano-2-(n-heptafluoropropyl)imidazolide) is proposed as a solid electrolyte interphase-stabilising additive for lithium-ion batteries, which can be added in a smaller amount than fluoroethylene carbonate (FEC) and vinylene carbonate (VC) additives. Electrolytes containing either lithium 4,5-dicyano-2-(trifluoromethyl)imidazolide (LiTDI) or battery-standard LiPF6 were tested with various amounts...
-
Nanotechnologies in Development of Structural Materials and Biomaterials
PublikacjaThe nanometric materials and technologies resulted in nanostructures are reviewed. The examples of nanomaterials are shown. The typical nanotechnologies, including plastic deformation, mechanical attrition, controlled detonation, hot plasma jet synthesis, laser vaporisation, CVD and PVD, mechanical milling, annealing, ultrasonic irradiation, nanolithography, electrocrystallisation, electrospinning, sol-gel method, cryogenic laser-enhanced...
-
High temperature corrosion and corrosion protection of porous Ni22Cr alloys
PublikacjaIn this work corrosion kinetics of the porous IN625 alloy is studied in the temperature range of 700 °C – 800 °C in air and humidified hydrogen for up to 1000 hours. Moreover, an effective and simple method of reducing corrosion rates of porous alloys by the infiltration of the rare earths elements is shown. Modification by the yttrium containing precursor reduces the corrosion rate by a factor of 50 in air at 700 °C so that the...
-
Simultaneous impedance and volumetric studies and additionally potentiodynamic polarization measurements of molasses as a carbon steel corrosion inhibitor in 1M hydrochloric acid solution
PublikacjaThe inhibition effect of molasses on the corrosion of low carbon steel in 1M hydrochloric acid solution was investigated by volumetric and electrochemical measurements. Potentiodynamic polarization and dynamic electrochemical impedance spectroscopy (DEIS) results were obtained and compared with to those, obtained with the hydrogen evolution technique. All results indicate that molasses functioned as a good inhibitor in 1M hydrochloric...
-
Crystal Structure of N-(2-Benzoyl-4,5-dimethoxyphenethyl)-2-phenylacetamide
PublikacjaThe crystal structure of N-(2-benzoyl-4,5-dimethoxyphenethyl)-2-phenylacetamide indicates that the compound crystallizes in the monoclinic C2/c space group with eight molecules in the unit cell. The heteroatoms from the amide group form a chain of intermolecular N-H ··· O hydrogen bonds propagating along the b axis. The carbonyl group from the benzoyl substituent participates in short contacts with two H-atoms from the ethyl or...
-
Experimental and predicted physicochemical properties of monopropanolamine-based deep eutectic solvents
PublikacjaIn this work, the novel deep eutectic solvents (DESs) based on 3-amino-1-propanol (AP) as hydrogen bond donor (HBD) and tetrabutylammonium bromide (TBAB) or tetrabutylammonium chloride (TBAC) or tetraethylammonium chloride (TEAC) as hydrogen bond acceptors (HBAs) were synthesized with different molar ratios of 1: 4, 1: 6 and 1: 8 salt to AP. Fourier Transform Infrared Spectroscopy measurements were performed to provide an evidence...
-
Storage of High-Strength Steel Flux-Cored Welding Wires in Urbanized Areas
PublikacjaThe condition of the consumables is a key factor determining the waste reduction in the welding processes and the quality of the welded joint. The paper presents the results of tests of four types of fux-cored wires dedicated for welding high-strength steels, stored for 1 month and 6 months in Poland in two urbanized areas: in a large seaside city (Gdańsk) and in Warsaw, located in the center of the country. The wires were subjected...
-
Computational Study of Molecular Interactions in ZnCl2(urea)2 Crystals as Precursors for Deep Eutectic Solvents
PublikacjaDeep eutectic solvents (DESs) are now enjoying an increased scientific interest due to their interesting properties and growing range of possible applications. Computational methods are at the forefront of deciphering their structure and dynamics. Type IV DESs, composed of metal chloride and a hydrogen bond donor, are among the less studied systems when it comes to their understanding at a molecular level. An important example...
-
A novel (Ti/Ce)UiO-X MOFs@TiO2 heterojunction for enhanced photocatalytic performance: Boosting via Ce4+/Ce3+ and Ti4+/Ti3+ redox mediators
PublikacjaTitanium-substituted cerium-oxo-based UiO MOFs with terephthalate linkers modified by various groups (–Br, –NH2, –NO2) or their derivatives (N-heterocyclic or biphenyl groups) were combined with titanium dioxide in a multistep route to obtain a core-shell-like architecture. DFT simulations showed that Ce- and bimetallic Ti/Ce- MOFs exhibited different charge compensation. Extended characterization revealed the formation of heterojunctions between...
-
Physical crosslinking of hyaluronic acid in the presence of phospholipids in an aqueous nano-environment
PublikacjaHyaluronic acid and phospholipids are two components in the synovial joint cavity that contribute to joint lubrication synergistically. Molecular dynamics simulations were performed and hydrogen bonds in hyaluronic acid were analyzed to identify specific sites that are responsible for its physical cross-linking. Two molecular masses of hyaluronic acid, 10 kDa and 160 kDa, were considered. We use molecular dynamics simulations and...
-
Study of the Anti-Staphylococcal Potential of Honeys Produced in Northern Poland
PublikacjaThe antimicrobial activity of 144 samples of honeys including 95 products from apiaries located in Northern Poland was evaluated. The antibacterial activity of those natural products, their thermal stability, and activity in the presence of catalase was investigated by microdilution assays in titration plates. The MTT assay was performed for the determination of anti-biofilm activity. Spectrophotometric assays were used for the...
-
Enhanced boron doping of thin diamond films grown in deuterium-rich microwave plasma
PublikacjaThe boron-doped diamond thin films were growth in deuterium rich microwave plasma in CVD process. The mechanism of influence of plasma composition on boron doping level was studied using optical emission spectroscopy. Deuterium rich plasma results in an increased dissociation of B2H6 precursor and intense boron-radicals' production. In consequence, a higher doping level of diamond films was observed by means of Laser Induced Breakdown...
-
Hyaluronan-Chondroitin Sulfate Anomalous Crosslinking Due to Temperature Changes
PublikacjaGlycosaminoglycans are a wide class of biopolymers showing great lubricating properties due to their structure and high affinity to water. Two of them, hyaluronic acid and chondroitin sulfate, play an important role in articular cartilage lubrication. In this work, we present results of the all-atom molecular dynamics simulations of both molecules placed in water-based solution. To mimic changes of the physiological conditions,...
-
Experimental and predicted physicochemical properties of monopropanolamine-based deep eutectic solvents
PublikacjaIn this work, the novel deep eutectic solvents (DESs) based on 3-amino-1-propanol (AP) as hydrogen bond donor (HBD) and tetrabutylammonium bromide (TBAB) or tetrabutylammonium chloride (TBAC) or tetraethylammonium chloride (TEAC) as hydrogen bond acceptors (HBAs) were synthesized with different molar ratios of 1:4, 1:6 and 1:8 salt to AP. Fourier Transform Infrared Spectroscopy measurements were performed to provide an evidence...
-
Influence of Annealing Atmospheres on Photoelectrochemical Activity of TiO2 Nanotubes Modified with AuCu Nanoparticles
PublikacjaIn this article, we studied the annealing process of AuCu layers deposited on TiO2 nanotubes (NTs) conducted in various atmospheres such as air, vacuum, argon, and hydrogen in order to obtain materials active in both visible and UV–vis ranges. The material fabrication route covers the electrochemical anodization of a Ti plate, followed by thin AuCu film magnetron sputtering and further thermal treatment. Scanning electron microscopy...
-
Hydrophobic deep eutectic solvents in microextraction techniques–A review
PublikacjaOver the past decade, deep eutectic solvents (DES) have been widely studied and applied in sample preparation techniques. Until recently, most of the synthesized DES were hydrophilic, which prevented their use in the extraction of aqueous samples. However, after 2015 studies on the synthesis and application of hydrophobic deep eutectic solvents (HDES) has rapidly expanded. Due to unique properties of HDES i.e. density, viscosity,...
-
Method of sacrificial anode dual transistor-driving in stray current field
PublikacjaIn order to control a magnesium anode in a stray current interference field, a dual transistor driving system has been proposed. It consisted of a combination of PNP and NPN transistors. Dual transistor driven system and direct anode to cathode connection were electrochemically tested in 3% NaCl solution. The dual transistor driven system increased the anode efficiency and reduced hydrogen evolution and the risk of embrittlement....
-
Reduction of the strontium titanate doped by Ytrium ceramics observed by X-ray photoemission spectroscopy method
Dane BadawczeYtrium-doped strontium titanate (YSTF) ceramics materials were manufactured by three various methods: 1) standard solid-state reaction method from Y2O3 (Sigma Aldrich, 99,9%), TiO2 (Sigma Aldrich, 99%) and SrCO3 (Sigma Aldrich,98%), 2) Pechini method, 3) wet method.
-
Bio based PUR-PIR foams thermal degradation (TG) and isoconversional kinetics
Dane BadawczeIn the present work, we perform a thorough thermogravimetric (TG) analysis of the bio-based polyurethane – polyisocyanurate (PUR-PIR) foams in both nitrogen and oxygen atmosphere. A sustainable element of the foam was a biopolyol obtained via acid-catalyzed liquefaction of Zostera Marina and Enteromorpha Algae biomass. Based on isoconversional analysis...
-
A General Synthesis of Diaryl Cyclic Diamidines
PublikacjaA convenient and general method has been developed for directly converting bis-nitriles, e.g., I, to cyclic diamidines, e.g., II, using reagents derived from diaminoalkanes, e.g., H2NCH2CH2NH2, satd. with hydrogen sulfide. A 1:1 mixt. of a diaminoalkane and Et alc. (or without) was effective in most cases (72-88%). The synthetic utility of this methodol. in the prepn. of tetrakis(cyclic amidino)pyrenes III (R = H, Me) from 1,3,6,8-tetracyanopyrene...
-
Factors causing degradation of sulfadimetoxine
PublikacjaSulfadimetoxine is a representative of sulfonamide drugs which presence inhibits growth of activated sludge bacteria, rhat is necessary for the effective mineralization of organic and inorganic contaminants. Therefore factors which con prevent this situation are searched. Aim of this study is selection of conditions causing efficien degradation of the drug- sulfadimetoxine. The impact of such aspects as : the type of oxidizing...
-
Electrical properties of Y0.08Sr0.92Ti0.92Nb0.08O3-δ after reduction in different reducing conditions
PublikacjaElectrical properties of perovskite Y0.08Sr0.92Ti0.92Nb0.08O3−ı after reduction in different conditions were studied. Relatively high electrical conductivity in samples reduced in ammonia was observed. The conductivity of Y0.08Sr0.92Ti0.92Nb0.08O3−ı reduced in ammonia at 1500 ◦C was of about 600 S/cm at 200 ◦C. Conductivity after reduction in ammonia at 1500 ◦C was stable both in hydrogen and oxygen atmosphere up to 600 ◦C. Reduction...
-
Method of sacrificial anode transistor-driving in cathodic protection system
PublikacjaA magnesium anode driving system has been proposed. A PNP driving transistor has been used. Electrochemical testing in 3%NaCl, results and comparison of the driving system and classic direct anode to cathode connection are presented. The driving system reduced the protection current and stabilized the working conditions of the anode. Higher anode efficiency was achieved. Overprotection and hydrogen embrittlement threats were prevented...
-
The properties of reduced Ge-Sb-O glasses for thermoelectric devices
PublikacjaThe structural and electrical properties of germanium-antimonate glasses after heat treatment in hydrogen have been determined. In the case of 50GeO2-50Sb2O3 glass reduced at 340°C even for less than 1 hour a continuous layer of antimony granules is formed and its electrical properties determine the surface conductivity of the reduced sample. The bulk electrical conductivity at 100°C of this sample was determined as 1000 Scm-1...
-
Synthesis and Testing of BCZY/LNZ Mixed Proton–electron Conducting Composites for Fuel Cell Applications
PublikacjaA composite of BaCe0.6Zr0.2Y0.2O3–δ and Li2O:NiO:ZnO was investigated for fuel cell applications. The composite was successfully synthesized and its phase stability was confirmed at temperatures up to 900 °C. The influence of sintering and pressing aids on density was also investigated. Electrical properties were measured. DC electrical conductivity was about 8•10-4 S/m at 845 K. Open circuit voltage measurements in wet hydrogen...
-
Electron Scattering on X(CH3)4 Molecules: Applicability of Simple Additivity Rule and Role of Methylation
PublikacjaTo investigate influence of target methylation (substitution of a hydrogen atom by methyl group) on electron-collision processes we compare absolute total cross sections for XH4 and X(CH3)4 molecules, where X is Si and Ge, respectively. We also compare experimental TCSs energy dependencies with estimated data obtained using simple formula and TCSs for methyl group and those for SiH4 and GeH4. Electron-scattering TCSs for mentioned...
-
Ultrasound-Assisted Dispersive Liquid-Liquid Microextraction Using Deep Eutectic Solvents (DESs) for Neutral Red Dye Spectrophotometric Determination
PublikacjaDeep eutectic solvents (DES), which have low toxicity and are low cost, biodegradable, and easily synthesized, were used for the extraction of neutral red (NR) dye before its spectrophotometric analysis. DES, containing choline chloride as a hydrogen bond acceptor and phenol as a hydrogen bond donor with a molar ratio of 1:2, was used for the extraction of NR dye from aqueous media. The possible interaction of different DESs with...
-
Communication: Inside the water wheel: Intrinsic differences between hydrated tetraphenylphosphonium and tetraphenylborate ions
PublikacjaTetraphenylphosphonium tetraphenylborate (TPTB) is a common reference electrolyte in physical chemistry of solutions allowing for a convenient partitioning of thermodynamic properties into single-ion contributions. Here, we compute on the basis of ab initio molecular dynamics simulations the infrared (IR) spectra for hydrated constituent ions of the TPTB assumption. Using spectral decomposition techniques, we extract important...
-
EFFECT OF SURFACE STATE AND STRESS ON AN OXIDATION OF THE ZIRCALOY-2 ALLOY
PublikacjaZr alloys are widely used as materials for nuclear fuel pellets in the nuclear industry. In the case of the LOCA or RIA happen, a temperature may locally reach high values. Even if the high temperature maintains shortly, the zirconium oxides may become permeable, absorb hydrogen appearing in cooling water from decomposition reaction and crack because of formation and brittle failure of hydrides. Such model cannot so far take into...
-
Plasticity of Bead-On-Plate Welds Made with the Use of Stored Flux-Cored Wires for Offshore Applications
PublikacjaExtreme atmospheric conditions in the marine and offshore industry are harmful to engineering materials, especially to welded joints, and may cause degradation of their properties. This article presents the results of research on the plasticity of bead-on-plate welds made using two types of seamless, copper plated flux-cored wires. Before welding, spools with wire were stored for 1 month in two distinct locations with different...
-
Insights into Stoichiometry Adjustments Governing the Performance of Flexible Foamed Polyurethane/Ground Tire Rubber Composites
PublikacjaPolyurethanes (PU) are widely applied in the industry due to their tunable performance adjusted by changes in the isocyanate index—stoichiometric balance between isocyanate and hydroxyl groups. This balance is affected by the incorporation of modifiers of fillers into the PU matrix and is especially crucial for PU foams due to the additional role of isocyanates—foaming of the material. Despite the awareness of the issue underlined...
-
Carbon Nanomaterials in Seed Priming: Current Possibilities
PublikacjaThe prevailing agricultural system has become deeply ingrained and insufficient due to outdated practices inherited from the Green Revolution, necessitating innovative approaches for sustainable agricultural development. Nanomaterials possess the potential to significantly improve the efficient utilization of resources while simultaneously encouraging sustainability. Among these, carbonaceous nanomaterials have found diverse applications...
-
Electrical and mechanical characterization of two-phase alloys by means of scanning probe microscopy in dynamic impedance spectroscopy mode
PublikacjaDynamic impedance spectroscopy, evaluated for measuring non-stationary systems, was used in combination with scanning probe microscope. Using this approach, localized impedance measurements in the AFM contact mode could be carried out. Additionally, impedance–force curves were made at each phase of investigated materials to illustrate the relation between impedance and the force applied to a probe. Therefore, correlation of electrical...
-
Preparation of 1-[Ω-(1,4,5,6-Tetrahydropyrimidin-2-yl)alkyl]thymines
PublikacjaOne-stage prepn. of the hydrochloride salts of 1-[ω-(1,4,5,6-tetrahydropyrimidin-2-yl)alkyl]-thymines, e.g. I, from 1-(ω-cyanoalkyl)thymines and a 1:1-mixt. of 1,3-diaminopropane and ethanol satd. with hydrogen sulfide is described. 1-(2-Cyanoethyl)-thymine gave a facile reversal of the Michael reaction to thymine under the conditions used. The reaction of 1,3-bis(3-cyanobenzyl)thymine with the above reagent produced 1,3-bis[3-(1,4,5,6-tetrahydropyrimidin-2-yl)benzyl]thymine.
-
The possibility of use keratin products in various branches of industry
PublikacjaBird's feather, the main by-product of the poultry industry, are not enough utilized and negatively influencing the environment. They contain large amount of keratin, the protein with high cystine content. The aim of our work was to obtain hydrolysates and isolates of keratin, which can be used in various areas of food, cosmetics, pharmaceutical industry and as animal feed. Keratin can be hydrolyzed and extracted from feather after...
-
Electron impact fragmentation of pyrrole molecules studied by fluorescence emission spectroscopy
PublikacjaThe fluorescence emission spectroscopy using electron impact excitation technique was employed to study fragmentation processes of the gas phase pyrrole molecules. The following excited fragmentation species were observed by detection of their fluorescence decay: the atomic hydrogen H(n), n = 4-7 and the diatomic CH(A2Δ), CN(B2Σ+), NH(A3Π) and C2(d3Πg) fragments. These atomic and molecular products differ from those previously...
-
Interactions between components of SrTi0.98 Nb0.02O3-δ-YSZ and SrTi0.98 Nb0.02O3-δ -CeO2 composites
PublikacjaComposites consisting of SrTiO3-based perovskite and either yttria-stabilized zirconia or ceria were investigated. The mechanical compatibility and possible inter-diffusion between phases were characterized by scanning electron microscopy, X-ray diffraction, and energy-dispersive X-ray spectroscopy. A gradual disappearance of Ce-containing phases with an increase in the temperature of reduction in hydrogen was noticed. Moreover,...
-
Environmental degradation of Ti alloys in artificial saliva and a role of fluorides
PublikacjaThe titanium and its alloys are potentially prone to hydrogen embrittlement, including those proposed for dental implants. The research has been aimed to assess a susceptibility to environment-enhanced degradation of the Ti-13Zr-13Nb alloy in artificial saliva with or without hydrofluoric acid, subject or not to cathodic polarisation. The results have shown that even if artificial saliva is safe environment, both cathodic polarization...
-
Environmental degradation of titanium alloy in artificial saliva
PublikacjaThe titanium and its alloys are potentially prone to hydrogen embrittlement, including those proposed for dental implants. The research has been aimed to assess a susceptibility to environment-enhanced degradation of the Ti-13Zr-13Nb alloy in artificial saliva with or without hydrofluoric acid, subject or not to cathodic polarisation. The results have shown that even if artificial saliva is safe environment, both cathodic polarization...
-
Influence of yttria surface modification on high temperature corrosion of porous Ni22Cr alloy
PublikacjaProtective coatings for porous alloys for high temperature use are relatively new materials. Their main drawback is high temperature corrosion. In this work protective coatings based the on Y-precursor infiltrated into the sintered Ni22Cr alloys are studied at 700°C. Effects of the amount of the protective phase on the resulting corrosion properties are evaluated in air and humidified hydrogen. Weight gain of the samples, their...
-
Redox State Sensitive Spectroscopy of the Model Compound [(H-dcbpy)(2)Ru-II(NCS)(2)](2-) (dcbpy=2,2 '-Bipyridine-4,4 '-dicarboxylato)
PublikacjaThe charge transfer reaction mechanism in a ruthenium polypyridine model complex with isothiocyanato ligands, i.e., [(H-dcbpy)(2)Ru(NCS)(2)](2-) 2Bu(4)N(+) (Ru2H) (dcbpy = 2,2'-bipyridine-4,4'-dicarboxylato), has been investigated by combining UV-vis absorption, resonance Raman spectroscopy, and electrochemical methods. Understanding the photophysics of light-harvesting complexes of this class is an indispensable prerequisite to...
-
Sub‐Nanometer‐Scale Cu9S5 Enables Efficiently Electrochemical Nitrate Reduction to Ammonia
PublikacjaThe sub-nanometer is a key feature size in materials science. Unlike single-atom and nanomaterials, size effects and inter-component cooperative actions in sub-nanomaterials will effective on its performance is more significant. Here, 0.95 nm ordered arrangement Cu9S5 sub-nanowires (Cu9S5 SNWs) are synthesized through the co-assembly effect of inorganic nuclei (Cu9S5) and clusters (phosphotungstic acid-PTA), achieving a significant...
-
Tailoring Diffusional Fields in Zwitterion/Dopamine Copolymer Electropolymerized at Carbon Nanowalls for Sensitive Recognition of Neurotransmitters
PublikacjaThe importance of neurotransmitter sensing in the diagnosis and treatment of many psychological illnesses and neurodegenerative diseases is non-negotiable. For electrochemical sensors to become widespread and accurate, a long journey must be undertaken for each device, from understanding the materials at the molecular level to real applications in biological fluids. We report a modification of diamondized boron-doped carbon nanowalls...
-
Catalytic Activity of Nickel and Ruthenium–Nickel Catalysts Supported on SiO2, ZrO2, Al2O3, and MgAl2O4 in a Dry Reforming Process
PublikacjaDry reforming of methane (DRM) is an eco-friendly method of syngas production due to the utilization of two main greenhouse gases—methane and carbon dioxide. An industrial application of methane dry reforming requires the use of a catalyst with high activity, stability over a long time, and the ability to catalyze a reaction, leading to the needed a hydrogen/carbon monoxide ratio. Thus, the aim of the study was to investigate the...
-
Solubility of Carbon Dioxide in Deep Eutectic Solvents Based on 3-Amino-1-Propanol and Tetraalkylammonium Salts at Low Pressure
PublikacjaDeep eutectic solvents (DESs) became an object of a great interest as an alternative to ionic liquids (ILs) and commonly used in CO2 capture amine solutions. In the present study, five different DESs based on 3-amino-1-propanol as physical-chemical CO2 absorbents were used. The composition was chosen in order to estimate the effects of hydrogen bond acceptor:hydrogen bond donor (HBA:HBD) molar ratio, anion type and length of alkyl...
-
Mechanical exfoliation and layer number identification of single crystal monoclinic CrCl3
PublikacjaAfter the recent finding that CrI3, displays ferromagnetic order down to its monolayer, extensive studies have followed to pursue new two-dimensional (2D) magnetic materials. In this article, we report on the growth of single crystal CrCl3 in the layered monoclinic phase. The system after mechanical exfoliation exhibits stability in ambient air (the degradation occurs on a time scale at least four orders of magnitude longer than...
-
Electrical and structural properties of Nb-doped SrTiO3
PublikacjaNiobium-doped strontium titanate synthesized via conventional solid-state reaction has been studied. Influence of niobium content on the lattice parameters and electrical conductivity has been reported. Various reduction conditions have been investigated. For samples reduced in hydrogen at 1400°C, a transition from thermally activated to metallic behavior has been observed. Maximum electrical conductivity (ca. 55 Scm−1 at 650°C)...
-
Syntheses and structures of the first terminal phosphanylphosphido complexes of molybdenum(IV)
PublikacjaThe reactions of R2P-P(SiMe3)Li (R = tBu, iPr2N) with [Cp2MoCl2] yield terminal phosphanylphosphido complexes formally via the insertion of the phosphinidene P-atom into the C - H bond of a cyclopentadienyl ring and the migration of the hydrogen atom or SiMe3 moiety to the molybdenum centre. Solid state structures of [Cp(C5H4P-PtBu2)MoH], [Cp(C5H4P-PtBu2)Mo(SiMe3)] and [Cp{C5H4P-P(NiPr2)2}Mo(SiMe3)] were established by single crystal...
-
Inhibitive effect of sodium molybdate on corrosion of AZ31 magnesium alloy in chloride solutions
PublikacjaIn this work, corrosion inhibition of the AZ31 magnesium alloy was investigated in NaCl solutions containing different amounts of sodium molybdate inhibitor. Electrochemical, hydrogen evolution, microscopic, and spectroscopic experiments were utilized to examine the mechanism of corrosion inhibition by molybdates. The results showed that Na2MoO4 inhibitor provides reliable inhibition at high concentrations (150 mM). Surface examination...