Filtry
wszystkich: 568
-
Katalog
Wyniki wyszukiwania dla: SILO BUCKLING
-
Wspomagana komputerowo weryfikacja określonego poziomu nienaruszalności bezpieczeństwa sil z wykorzystaniem autorskiej aplikacji ProSIL
PublikacjaW referacie przedstawiono oprogramowanie Pro SIL wspomagające zarządzanie bezpieczeństwem funkcjonalnym. Program ProSIL składa się z trzech modułów wspomagających: określanie wymaganego poziomu SIL (moduł ProSILen) weryfikację SIL (moduł ProSILer) oraz przeprowadzenie analizy warstw zabezpieczeń metodą LOPA. W aplikacji ProSIL zaimplementowano opracowaną w trakcie badań metodykę analizy bezpieczeństwa funkcjonalnego w projektowaniu...
-
Use of radiography images and gray level co-occurrence matrix to investigate gravitational granular flow
PublikacjaThe paper presents analysis of granular gravitational flow based on radiography images processing. The investigations were conducted for silo model geometry with concentric/eccentric discharging modes. The continuous X-ray radiography scans of granular material distribution, acquired during flow, were obtained by means of an especially designed model silo with rectangular bin and different settings of hopper angles. Image processing...
-
Renal denervation achieved by endovascular delivery of ultrasound in RADIANCE-HTN SOLO or by radiofrequency energy in SPYRAL HTN-OFF and SPYRAL-ON lowers blood pressure
Publikacja -
Hipogrifo-Revista de literatura y cultura del Siglo de Oro
Czasopisma -
<title>Control and monitoring of data acquisition and trigger system (TRIDAQ) for backing calorimeter (BAC) of the ZEUS experiment</title>
Publikacja -
Soft Sensor Application in Identification of the Activated Sludge Bulking Considering the Technological and Economical Aspects of Smart Systems Functioning
PublikacjaThe paper presented the methodology for the construction of a soft sensor used for activated sludge bulking identification. Devising such solutions fits within the current trends and development of a smart system and infrastructure within smart cities. In order to optimize the selection of the data-mining method depending on the data collected within a wastewater treatment plant (WWTP), a number of methods were considered, including:...
-
Tackling Air Pollution in Cities with Modelling and Simulation: Remote Group Model Building as an Educational Tool Supporting System Dynamics Modelling
Publikacja -
Curing behavior of epoxy/Fe 3 O 4 nanocomposites: A comparison between the effects of bare Fe 3 O 4 , Fe 3 O 4 /SiO 2 /chitosan and Fe 3 O 4 /SiO 2 /chitosan/imide/phenylalanine-modified nanofillers
PublikacjaIn this study, Fe3O4 magnetic nanoparticles (MNPs) were synthesized (B-MNP) and then modified with SiO2 to form Fe3O4/SiO2 core/shell MNPs. The Fe3O4/SiO2 MNPs were chemically functionalized with chitosan so as to gain Fe3O4/SiO2/Chitosan (CH-MNP). The CH-MNP was functionalized with a macromolecule containing imide and phenylalanine precursors to gain Fe3O4/SiO2/Chitosan/imide/phenylalanine based MNPs (CH-IM-MNP). The differences...
-
Determining and verifying the safety integrity level of the controland protection systems under uncertainty
PublikacjaThe probabilistic models of the electrical, electronic and programmable electronic (E/E/PE)systems, which are proposed in the IEC 61508 and IEC 61511 standards, do not cover the uncertainty aspectsof results obtained from these models. The proposed method takes into consideration the sensitivity analysisof probabilistic models of E/E/PE systems as well as the uncertainty of probabilistic results. It uses differentialfactors, which...
-
Development of a solventless stir bar sorptive extraction/thermal desorption large volume injection capillary gas chromatographic-mass spectrometric method for ultra-trace determination of pyrethroids pesticides in river and tap water samples
Publikacja -
Sensitivity analysis of critical forces of trusses with side bracing
PublikacjaThe present research is devoted to the study of out-of-plane buckling of trusses with elastic side bracing. Inthis paper, a sensitivity analysis of critical buckling loads of a truss due to bracing stiffness is carried out. A method based on the sensitivity analysis for the determination of the threshold bracing stiffness conditionfor full bracing of a truss is proposed. The influence lines of the unit change of the bracing stiffness...
-
Investigation of natural frequencies of axially loaded thin-walled columns
PublikacjaThe paper deals with correlation between natural frequencies of two steel thin-walled columns and the corresponding applied load. The structures are made of cold-formed lipped channel sections. The columns lengths were assumed to follow two buckling patterns – global flexural and flexural-torsional buckling. In the thicker structure two material models were considered – linearly-elastic and elastic-perfectly plastic. Numerical...
-
Stability and load bearing capacity of a truss with elastic braces
PublikacjaThe present paper is devoted to the numerical and experimental investigations of stability of a truss stiffened by elastic braces. The model of a real roof truss scaled by factor ¼ was investigated. In the research the linear buckling and non-linear static analysis of the truss shell and beam model with geometric and material non-linearity is presented. The initial imperfections were assumed in the form of the first buckling mode....
-
Adam Macierzanka dr hab. inż.
Osoby2015-presentHead of Department, Associate ProfessorDepartment of Colloid and Lipid Science, Faculty of Chemistry, Gdansk University of Technology, Gdansk, Poland 2019-2020Visiting Professor, Food Science and NutritionRiddet Institute, Massey University, Palmerston North, New Zealand 2014-2015Research LeaderColloid Science, Food & Health Research ProgrammeInstitute of Food Research, Norwich, United Kingdom 2012-2014Full Professor,...
-
VIbration monitoring in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - PARAFFIN OIL. Specim. set K09A - full-run
Dane BadawczeVIbration monitoring in reciprocating siding friction tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: PARAFFIN OIL. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30,...
-
VIbration monitoring in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - PARAFFIN OIL. Specim. set K09 - pre-run
Dane BadawczeVIbration monitoring in reciprocating siding friction tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: PARAFFIN OIL. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30,...
-
VIbration monitoring in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). No lubrication (DRY). Specim. set K05
Dane BadawczeVIbration monitoring in reciprocating siding friction tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: DRY. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180...
-
VIbration monitoring in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - PARAFFIN OIL. Specim. set K08
Dane BadawczeVIbration monitoring in reciprocating siding friction tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: PARAFFIN OIL. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30,...
-
VIbration monitoring in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - DISTILLED WATER. Specim. set K02
Dane BadawczeVIbration monitoring in reciprocating siding friction tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: DISTILLED WATER. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15,...
-
VIbration monitoring in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - DISTILLED WATER. Specim. set K06
Dane BadawczeVIbration monitoring in reciprocating siding friction tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: DISTILLED WATER. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15,...
-
VIbration monitoring in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - DISTILLED WATER. Specim. set K07
Dane BadawczeVIbration monitoring in reciprocating siding friction tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: DISTILLED WATER. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15,...
-
VIbration monitoring in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). No lubrication (DRY). Specim. set K03
Dane BadawczeVIbration monitoring in reciprocating siding friction tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: DRY. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180...
-
VIbration monitoring in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). No lubrication (DRY). Specim. set K04
Dane BadawczeVIbration monitoring in reciprocating siding friction tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: DRY. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180...
-
VIbration monitoring in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). No lubrication (DRY). Specim. set K01
Dane BadawczeVIbration monitoring in reciprocating siding friction tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: DRY. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180...
-
An algorithm to generate high dense packing of particles with various shapes
PublikacjaDiscrete Element Method (DEM) is one of available numerical methods to compute movement of particles in large scale simulations. The method has been frequently applied to simulate the cases of grain or bulk material as the major research issue. The paper describes a new method of generating high dense packing with mixed material of two different shape used in DEM simulation. The initial packing is an important parameter to control,...
-
Comparison of classical Winter's bracing requirements of compressedtruss chord with stability analysis of 3D truss-model
PublikacjaMost code requirements concerning bracing are based on principles developed by Winter. The present research is devoted tostudy a lateral buckling of truss with linear elastic side supports. The classical Winter's model of truss chord in the case ofout of the truss plane buckling is compared with nonlinear analysis of 3D truss model. Full bracing condition, that permitsthe truss chord to support load level corresponding to an unbraced...
-
Sensitivity analysis of critical loads of I-columns
PublikacjaThe first order variation of critical buckling load of thin-walled columns with bisymmetric open cross-section due to some variations of the design variables such as: cross-section dimensions, or material characteristics is derived. The influence of the residual welding stresses is taken into account. In the numerical examples dealing with I-column the functions describing the effect of the variation of the dimensions of the flange...
-
Stability of roof trusses stiffened by trapezoidal sheeting and purlins
PublikacjaIn the article linear buckling analysis of a set of steel trusses braced by purlins and trapezoidal sheeting are conducted. The buckling load factor due to the height of a corrugated sheeting profile is investigated in parametric studies. The minimal height of trapezoidal sheeting required for preventing the sheeting and chords of the trusses against the buckling is obtained. Two groups of models are considered: “axial” model as...
-
Stability of an imperfect truss loaded by wind
PublikacjaThe present paper is devoted to the numerical research of stability of a truss loaded by wind and stiffened by elastic supports located at the top chord. The lateral braces or lateral and torsional braces were taken into account. In this paper, the linear buckling analysis re- sults for the beam and shell model were presented. Two different shapes of initial geometric imperfections were considered in the non-linear static analysis...
-
Analysis of sloping brace stiffness influence on stability and load bearing capacity of a truss
PublikacjaThe paper is focused on the numerical study of stability and load bearing capacity of a truss with side elastic braces. The structure is made in reality. The rotational and sliding brace stiffnesses were taken into account. Linear buckling analysis and non-linear static analysis with geometric and material nonlinearity were performed for the beam and shell model of the truss with respect to the angle of sloping braces. As a result...
-
STABILITY ANALYSIS OF A TRUSS WITH SLOPING ELASTIC BRACES
PublikacjaSteel trusses have a much greater strength and stiffness in their plane than out of their plane, and therefore should be braced against lateral deflection and twisting. Such elements like purlins apart from bearing vertical load are part of bracing that stabilize roof trusses against distortional buckling. The stability of trusses with elastic bracing was investigated in an experimental research. Braces situated at some angle measured...
-
ANALYSIS OF BRACE STIFFNESS INFLUENCE ON STABILITY OF THE TRUSS
PublikacjaThe paper is devoted to the numerical and experimental research of stability of a truss with side elastic supports at the top chord. The structure is a model of a real roof truss scaled by factor ¼. The linear buckling analysis and non-linear static analysis were carried out. The buckling length factor for the compressed top chord was calculated and the limit load for the imperfect truss shell model with respect to brace stiffness...
-
Selected local stability problems of channel section flanges made of aluminium alloys
PublikacjaThe paper addresses the issue of local buckling of compressed flanges of cold-formed thin-walled channel columns and beams with nonstandard flanges composed of aluminium alloys. The material behaviour follows the Ramberg–Osgood law. It should be noted that the proposed solution may be also applied for other materials, for example: stainless steel, carbon steel. The paper is motivated by an increasing interest in nonstandard cold-formed...
-
Stability of a truss under upward wind loading
PublikacjaThe present paper is devoted to the numerical investigations of stability of a truss under upward wind load. The truss is braced at its the upper cord. A structural variant including lateral braces, or lateral and torsional braces is considered. The research presents the problems of linear buckling and non-linear static analysis of the truss shell and beam model with geometric and material non-linearity are presented. The initial...
-
Stability of an Innovative Cold-Formed GEB Section
PublikacjaThis paper is focused on the numerical analysis and experimental test of stability of the cold-formed profile with an innovative GEB cross-section. For the shell model of the axially compressed member, the linear buckling analysis and the nonlinear static analysis were carried out. In the numerical research, the buckling load and the limit load for variable section heights were obtained. Some of the results were compared with the...
-
Determination of the shape of the CFGFT cylindrical column based on laboratory tests
PublikacjaAnalyses were carried out on glass-fibre-reinforced polymer tube columns with reference to laboratory tests. The angles of the glass fibre beams were 20◦, 55◦ and 85◦. The study employed non-classical operational calculus. Various modulated harmonic signal shapes were considered for columns and tubes at buckling. The buckling loads were assessed and compared for different models.
-
Functional Safety Analysis including Human Factors
PublikacjaIn this paper selected aspects of human factors are discussed that should be taken into account during the design of safety-related functions for a complex hazardous installation and its protections. The layer of protection analysis (LOPA) methodology is used for simplified risk analysis based on defined accident scenarios. To control the risk the safety instrumented functions (SIFs) are identified and their safety integrity levels...
-
The impact of material degradation on the resistance and reliability of truss structures
PublikacjaThe paper analyses limit load-carrying capacity and buckling load of truss towers used to support high voltage power lines. The analysed typical structure was subjected to characteristic loads and their combinations. The results were applied to assess structural resistance with regard to steel corrosion in the long-term operation. The extent of structural deterioration was assessed due to Young's modulus decrement in the course...
-
Implementation of Non-Probabilistic Methods for Stability Analysis of Nonlocal Beam with Structural Uncertainties
PublikacjaIn this study, a non-probabilistic approach based Navier’s Method (NM) and Galerkin Weighted Residual Method (GWRM) in term of double parametric form has been proposed to investigate the buckling behavior of Euler-Bernoulli nonlocal beam under the framework of the Eringen's nonlocal elasticity theory, considering the structural parameters as imprecise or uncertain. The uncertainties in Young’s modulus and diameter of the beam are...
-
Kontrowersje wokół zagadnienia sprawiedliwości dystrybutywnej
PublikacjaArtykuł rekapituluje szkicowo kilka głównych ujęć problemu sprawiedliwości dystrybutywnej, osadzając wybrane stanowiska w kontekście klasycznych debat z filozofii polityki i filozofii społecznej. Sprawiedliwość dystrybutywną należy rozumieć jako normatywną zasadę dotyczącą tego w jaki sposób społeczeństwo rozdziela ograniczoną pulę zasobów wśród swoich członków. Punktem wyjścia dla artykułu jest słynna zasada dyferencji Rawlsa,...
-
Stability of truss with side - supports. The case of linear and rotational elastic supports
PublikacjaThe research is devoted to study lateral buckling of truss with linear and rotational elastic side-supports. Geometrically nonlinear analysis of example truss with linear and rotational elastic sidesupports is carried out. The limit normal force in compressed chord of the truss due to stiffness of side supports is calculated. The elastic support reaction in relation to force in compressed chordand coefficient of buckling length...
-
Innovative Cold-formed GEB Section under Bending
PublikacjaThis paper is concerned with the numerical bending capacity study of the innovative cold-formed GEB sections. Both linear buckling analysis and non-linear static analysis incorporating geometric and material nonlinearity were carried out employing a shell structural model. The magnitudes of buckling load and limit load with respect to GEB section depth and thickness were obtained. The opened cold-formed section was tested assuming...
-
Legal requirements and wastewater discharges to Polish water bodies, 1945-2003
PublikacjaArtykuł podaje zmieniające się wymagania wobec jakości oczyszczonych ścieków w Polsce w okresie 1945-2003.Wskazuje się na podejście prawne w okresie ustroju socjalistycznego, zmiany które nastąpiły po upadku tego ustroju oraz sytuację, jaka pojawila się po wstąpieniu Polski do Unii Europejskiej. Podano przykładowe obliczenia celem zilustrowania ilościowych konsekwencji obowiązujacego w Polsce prawa dotyczącego ścieków.
-
Effect of the dye amount on physical properties of silicone pressure sensitive adhesives Wp�yw ilo�ci barwnika na fizyczne w�a�ciwo�ci silikonowych klej�w samoprzylepnych
Publikacja -
Non-linear static stability of bi-layer carbon nanosheets resting on an elastic matrix under various types of in-plane shearing loads in thermo-elasticity using nonlocal continuum
PublikacjaIn this research, the shear and thermal buckling of bi-layer rectangular orthotropic carbon nanosheets embedded on an elastic matrix using the nonlocal elasticity theory and non-linear strains of Von-Karman was studied. The bi-layer carbon sheets were modeled as a double-layered plate, and van der Waals forces between layers were considered. The governing equations and boundary conditions were obtained using the first order shear...
-
Stability and load bearing capacity of a braced truss under upward wind loading
PublikacjaThe paper is focused on the numerical and experimental investigation of stability of a steel truss under upward wind loading. The structure was stiffened by elastic braces situated at the top and bottom chord. Usually the lateral (translational) brace stiffness is considered. However, the rotational stiffness of braces caused by interaction between torsional stiffness of the truss top chord and bending stiffness of the roof elements...
-
Stability and load bearing capacity of a braced truss under upward wind loading
PublikacjaThe paper is focused on the numerical and experimental investigation of stability of a steel truss under upward wind loading. The structure was stiffened by elastic braces situated at the top and bottom chord. Usually the lateral (translational) brace stiffness is considered. However, the rotational stiffness of braces caused by interaction between torsional stiffness of the truss top chord and bending stiffness of the roof elements...
-
Maciej Niedostatkiewicz dr hab. inż.
Osoby -
STABILITY AND LOAD BEARING CAPACITY OF A BARS WITH BUILT UP CROSS SECTION AND ELASTIC SUPPORTS
PublikacjaThe present paper is devoted to the numerical analysis and experimental tests of compressed bars with built–up cross section which are commonly used as a top chord of the roof trusses. The significant impact on carrying capacity for that kind of elements in case of out-of-plane buckling is appropriate choice of battens which are used to provide interaction between separate members. Linear buckling analysis results and nonlinear static...
-
Studia Aurea-Revista de Literatura Espanola y Teoria Literaria del Renacimiento y Siglo de Oro
Czasopisma