Wyniki wyszukiwania dla: PVDS
-
Modeling lubricant flow between thrust-bearing pads
PublikacjaInlet temperature is one of the main inputs in all models for the analysis of fluid film bearing performance. At the same time, inlettemperature distribution and also oil velocity distribution at the inlet are the result of flow phenomena in the gap between the bearingpads. These phenomena are complex and in many cases further affected by any special arrangements of forced oil supply to the gapbetween pads. The reason for such...
-
Determination of Liquid Detergent Pods as a Potential Microplastic Source
PublikacjaWashing pods became a popular way to add detergent to washing machines. Despite the claims about the degradability of the pod film, the sludge in pipes can be observed after the usage of such pods. This study focused on a quantitative and qualitative analysis of washing pod films as a source of microplastic.
-
Influence of thermal effects on mechanical properties of PVDF-coated fabric
PublikacjaThis paper describes the method of laboratory tests necessary for identification of temperature influence on mechanical properties of polyvinylidene fluoride-coated polyester fabric often used for tensile structures. Two nonlinear model descriptions are investigated. The first one is based on the piece-wise linear relations between stress and strain and the second one on the Murnaghan model of solid behavior. This paper is proposed...
-
Mechanical properties of PVDF-coated fabric under tensile tests
PublikacjaThis article describes the laboratory tests necessary to identify the mechanical properties of the polyvinylidene fluoride (PVDF)-coated fabrics named Precontraint 1202S and Precontraint 1302S. First, a short survey of the literature concerning the description of coated woven fabrics is presented. Second, the material parameters for PVDF-coated fabrics are specified on the basis of biaxial tensile tests. A comparison of the 1:1...
-
The Rolling Contact Fatigue of PVD Coated Spur Gears
Publikacja -
Sun shines also in Poland - PV's global market and its future in Poland
PublikacjaNiekorzystne zmiany klimatyczne stanowią wyzwanie do poszukiwania konkurencyjnych ekotechnologii. Fotowoltaika ma szansę stać się ważnym źródłem energii w 21 wieku na całym świecie. Systemy fotowoltaiczne (PV) dostarczają energii elektrycznej w wyniku konwersji energii promieniowania słonecznego i przewiduje się, że wniosą one znaczący wkład w systemy energetyczne dzięki stałemu postępowi technologicznemu w tej dziedzinie i znaczącej...
-
Klocki samopompujące w łożyskach hydrodynamicznych = Self-pumping pads in the hydrodynamic bearings
PublikacjaWe współpracy z firmą ALSTOM HYDRO (Szwajcaria), zespół Katedry Konstrukcji i Eksploatacji Maszyn Politechniki Gdańskiej przeprowadził symulacje przepływowe kilku rozwiązań konstrukcyjnych mających na celu zwiększenie niezawodności turbin wodnych. W artykule opisano jedno z takich rozwiązań - tak zwane łożysko z klockami samopompującymi. Głównym celem jest uzyskanie przepływu oleju w układzie smarowania łożyska hydrodynamicznego...
-
Influence of morphology of PVDF capillary membranes on the performance of direct contact membrane distillation
Publikacja -
Characterization of PVDF/Graphene Nanocomposite Membranes for Water Desalination with Enhanced Antifungal Activity
PublikacjaSeawater desalination is a worldwide concern for the sustainable production of drinking water. In this regard, membrane distillation (MD) has shown the potential for effective brine treatment. However, the lack of appropriate MD membranes limits its industrial expansion since they experience fouling and wetting issues. Therefore, hydrophobic membranes are promising candidates to successfully deal with such phenomena that are typical...
-
Prediction of the properties of PVD/CVD coatings with the use of FEM analysis
Publikacja -
The wear of PVD coated elements in oscillation motion at high temperature
Publikacja -
Improvement of Thrust Bearing Calculation Considering the Convectional Heating within the Space between the Pads
PublikacjaA modern thrust bearing tool is used to estimate the behavior of tilting pad thrust bearings not only in the oil film between pad and rotating collar, but also in the space between the pads. The oil flow in the space significantly influences the oil film inlet temperature and the heating of pad and collar. For that reason, it is necessary to define an oil mixing model for the space between the pads. In the bearing tool, the solutions...
-
Improvement of the thrust bearing calculation considering the convectional heating within the space between the pads
PublikacjaA modern thrust bearing calculation tool should consider not only the oil film between pad and rotating collar but also the space between the pads. The oil flow in the space has a significant influence on the oil film inlet temperature, the convectional cooling of pad and collar and should be included in the bearing calculation methods. The authors use a tool developed at Clausthal University of Technology in cooperation with the...
-
The method of tribotesting of PVD coated elements in oscillation motion at high temperature
Publikacja -
Graphene-Coated PVDF Membranes: Effects of Multi-Scale Rough Structure on Membrane Distillation Performance
PublikacjaGraphene-coated membranes for membrane distillation have been fabricated by using a wet-filtration approach. Graphene nanoplatelets have been deposited onto PVDF membrane surfaces. Morphology and physicochemical properties have been explored to evaluate the changes in the surface topography and related effects on the membrane performance in water desalination. The membranes have been tested in membrane distillation plants by using...
-
The Problems of Application of PVD/CVD Thin Hard Coatings for Heavy-Loaded Machine Components
Publikacja -
GIS estimated potential of rooftop PVs in urban areas - case study Wrocław (Poland)
Publikacja -
Artificial neural networks as a tool for selecting the parameters of prototypical under sleeper pads produced from recycled rubber granulate
Publikacja -
The transition from HIF-1 to HIF-2 during prolonged hypoxia results from reactivation of PHDs and HIF1A mRNA instability
Publikacja -
Odporność kawitacyjna grubych powłok ochronnych CrC nanoszonych metodą niskociśnieniowego wyładowania łukowego (Arc-PVD)
PublikacjaReferat przedstawia analizę i metodę pokrywania powierzchni materiałów zastosowanych w turbinach parowych i śrubach okrętowych za pomocą CrC przy zastosowaniu metodę ARC-PVD. Celem jest podwyższenie trwałości powierzchni narażających na erozję wywołaną przez kawitację.
-
Structure and properties of the Ti+Ti(C,N) coatings obtained in the PVD process on sintered high speed steel
Publikacja -
Hydrophobic PVDF hollow fiber membranes with narrow pore size distribution and ultra-thin skin for the fresh water production through membrane distillation
Publikacja -
Evaluation of TiO2/UV; O3/UV, and PDS/Vis for improving chlorfenvinphos removal from real municipal treated wastewater effluent
Publikacja -
Farzin Kazemi
OsobyHis main research areas are seismic performance assessment of structures and seismic hazard analysis in earthquake engineering. He performed a comprehensive study on the effect of pounding phenomenon and proposed modification factors to modify the seismic collapse capacity of structures or predict the seismic collapse capacity of structures which were retrofitted with linear and nonlinear Fluid Viscous Dampers (FVDs). His current...
-
A New Microwave Ceramic – Polymer Composite with 0-3 Connectivity
PublikacjaGoal of the present research was to fabricate and study two-phase BiNbO4//PVDF composites with 0-3 connectivity. Such composite consists of there-dimensionally connected polymer matrix loaded with dielectric ceramic particles. In the present case BiNbO4 powder acted as an active phase (dispersed phase) whereas polyvinylidene fluoride (PVDF) acted as a non-active (passive) phase (matrix). BiNbO4//PVDF composites with the volume...
-
A comprehensive survey on low-cost ECG acquisition systems: Advances on design specifications, challenges and future direction
PublikacjaAvailability of low-cost, reliable, and portable Electrocardiography (ECG) devices is still very important in the medical world today. Despite the tremendous technological advancement, Cardiovascular Diseases (CVDs) remain a serious health burden claiming millions of lives on an annual basis globally. This is more prevalent in Low and Middle-Income Countries (LMICs) where there are huge financial instability and lack of critical...
-
Poly(hydroxybutyrate-co-hydroxyvalerate) as a biodegradable binder in a negative electrode material for lithium-ion batteries
PublikacjaIn this work, graphite-based negative electrode for lithium-ion battery consisting a novel and biodegradable binder poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV) is compared with standard graphite electrode with polyvinylidene fluoride (PVDF) as a binder. The rate and cycling performance of lithium ion insertion/extraction of electrodes with PHBV in a half-cell configuration are evaluated. Moreover, on the basis of the electrochemical...
-
Hemocompatibility of nanocrystalline diamond layers
Dane BadawczeThe biocompatibility of the diamond films were investigated with whole human blood samples. Blood used in this study was drawn from 10 healthy human patients of different age, sex, and blood group. A 2 ml samples were collected into standard tubes with EDTA anticoagulation agent. Blood was used within 6 hours from the collection time. A reference blood...
-
SYNTHETIZED MEMBRANES FOR ULTRASOUND-ASSISTED SOLVENT EXTRACTION OF POROUS MEMBRANE PACKED SOLID SAMPLES.
PublikacjaMembranes are becoming more and more popular in analytical chemistry, which is why they are used, among others, in extraction processes. Therefore, this work focuses on the process of synthesis PVDF membranes and its optimization. The obtained membranes were used as bags for the phthalate extraction in disposable diapers for babies. Extraction was accomplished by method ultrasound-assisted solvent extraction of porous PVDF membrane...
-
Decolorisation of Methylene Blue with Sodium Persulfate Activated with Visible Light in the Presence of Glucose and Sucrose
PublikacjaThe paper presents the results of research on the methylene blue (MB) degradation with sodium persulfate (PDS) activated with visible light (Vis) in the presence of glucose and sucrose. The following test were examined: absence and presence of sugars in concentrations of 50–300 mM, presence and absence of Vis radiation, pH of the model solution (6.0–12.0), identification of free radicals, kinetics of the pseudo-first-order reaction....
-
Optimal retrofit strategy using viscous dampers between adjacent RC and SMRFs prone to earthquake‑induced pounding
PublikacjaNowadays, retrofitting-damaged buildings is an important challenge for engineers. Finding the optimal placement of Viscous Dampers (VDs) between adjacent structures prone to earthquake-induced pounding can help designers to implement VDs with optimizing the cost of construction and achieving higher performance levels for both structures. In this research, the optimal placement of linear and nonlinear VDs between the 3-story, 5-story,...
-
Seismic performance evaluation of steel buckling-restrained braced frames including SMA materials
PublikacjaThe permanent deformation of the building after seismic excitations can be determined by the Maximum Residual Interstory Drift Ratio (MR-IDR), which may be used for measuring the damage states. Low-post yield stiffness of the steel buckling-restrained braced frame (BRBF) makes this system vulnerable to large MR-IDR after a severe earthquake event. To overcome this issue, this paper investigates the seismic limit state performances...
-
Reliability of acicular grindable thermocouples for transient temperature measurements at sliding contacts
PublikacjaAcicular grindable thermocouples represent an interesting and prospective technique of temperature measurements at sliding contacts. This study aimed at the investigation of their reliability and accuracy as applied to the friction materials of various classes in contact with steel. The tests were conducted on a pin-on-disc tribometer under stationary and transient regimes. The experimental results were validated by comparing the...
-
Global value chains, wages, employment and labour production in China: A regional approach
PublikacjaIn this study we analyse the relationship of trade and global value chains (GVCs) to the labour market in 31 Chinese provinces for 25 sectors, by means of a system of structural equations. We firstly distinguish between provincial value chains (PVCs) and interprovincial value chains (PRVCs) in order to outline their distribution and evolution over time. Then, we investigate to what extent participation in GVCs, PVCs and PRVCs –...
-
Effect of soil on the capacity of viscous dampers between adjacent buildings
PublikacjaThis study investigated the seismic pounding of two adjacent buildings considering soil–structure interaction (SSI). A comprehensive parametric study of buildings with different heights was performed to reveal the pounding-involved behaviour considering the soil effect. Wavelet transform has been conducted to gain insight into the differences in the frequency contents of the impact forces between fixed- and flexible-base adjacent...
-
Dielectric Properties of BiNbO<sub>4</sub>-Based Ceramic-Polymer Composites with 0-3 Connectivity
PublikacjaIn the present study two-phase BiNbO4//PVDF composites with 0-3 connectivity were studied by impedance spectroscopy within the frequency range Δν=100Hz-1MHz at room temperature. Polyvinylidene fluoride (PVDF) acted as a matrix whereas bismuth niobate (BiNbO4) powder acted as a dispersed phase. The volume fraction of the ceramic phase was cV=2, 4, 6, 8, 10, 16 and 20vol%. Analysis of the impedance data registered for composites...
-
Predicting the seismic collapse capacity of adjacent SMRFs retrofitted with fluid viscous dampers in pounding condition
PublikacjaSevere damages of adjacent structures due to structural pounding during earthquakes have emphasized the need to use some seismic retrofit strategy to enhance the structural performance. The purpose of this paper is to study the influence of using linear and nonlinear Fluid Viscous Dampers (FVDs) on the seismic collapse capacities of adjacent structures prone to pounding and proposing modification factors to modify the median...
-
Predicting the seismic collapse capacity of adjacent SMRFs retrofitted with fluid viscous dampers in pounding condition
PublikacjaSevere damages of adjacent structures due to structural pounding during earthquakes have emphasized the need to use some seismic retrofit strategy to enhance the structural performance. The purpose of this paper is to study the influence of using linear and nonlinear Fluid Viscous Dampers (FVDs) on the seismic collapse capacities of adjacent structures prone to pounding and proposing modification factors to modify the median...
-
Locust bean gum as green and water-soluble binder for LiFePO4 and Li4Ti5O12 electrodes
PublikacjaLocust Bean Gum (LBG, carob bean gum) was investigated as an environmentally friendly, natural, and water-soluble binder for cathode (LFP) and anode (LTO) in lithium-ion batteries (Li-ion). For the frst time, we show LBG as an electrode binder and compare to those of the most popular aqueous (CMC) and conventional (PVDF) binders. The electrodes were characterized using TGA/DSC, the galvanostatic charge–discharge cycle test, cyclic...
-
Comparative review of piezoelectric biomaterials approach for bone tissue engineering
PublikacjaBone as a minerals’ reservoir and rigid tissue of the body generating red and white blood cells supports various organs. Although the self-regeneration property of bone, it cannot regenerate spontaneously in severe damages and still remains as a challenging issue. Tissue engineering offers several techniques for regenerating damaged bones, where various biomaterials are examined to fabricate scaffolds for bone repair. Piezoelectric...
-
Metody modyfikacji warstw wierzchnich nanomateriałami
PublikacjaPrzedstawiono aktualnie stosowane metody nakładania warstw wierzchnich z materiałów nanokrystalicznych; PVD, CVD, elektrochemiczne, zol-żel (sol-gel) i metodę sonochemiczną.
-
Wpływ automatycznej kalibracji wizyjnego systemu pozycjonowania na dokładność lokalizacji elementu roboczego
PublikacjaW artykule przedstawiono strukturę i działanie automatycznego wizyjnego systemu pozycjonowania (PVS), który został zainstalowany na maszynie waterjet (WJ). Ponadto przeprowadzono analizę wpływu kalibracji na działanie PVS. Podstawę systemu stanowią dwie kamery internetowe zamontowane na przemysłowej maszynie WJ. W połączeniu z algorytmem identyfikacji, system przeznaczony jest do pozycjonowania WJ z dużą dokładnością. W tym celu...
-
Topography studies of screen-printed carbon electrodes (SPCE) with boron-doped diamond foils
Dane BadawczeThis dataset contains topography examination of SPCE containing boron-doped diamond BDD foils done with scanning electron microscope. Different points mark different electrode spots: A) working electrode, B) reference electrode, C) counter electrode, D) pads.
-
The newly developed multipurpose ROV or an integrated mine hunting system
PublikacjaA modular mine hunting ROV concept is presented. The design is based on experience gained during 15 years of exploitation of the Ukwial ROV and development of Gluptak single shot mine hunting systems. The design goal was to multiply capabilities of the Ukwial without increasing weight and dimensional envelope. The vehicle is composed around powerful propulsion system that gives the system basic PVDS capability and mine disposal...
-
An Analysis of Uncertainty and Robustness of Waterjet Machine Positioning Vision System
PublikacjaThe paper presents a new Automatic Waterjet Positioning Vision System (AWPVS) and investigates components of workpiece positioning accuracy. The main purpose of AWPVS is to precisely identify the position and rotation of a workpiece placed on a waterjet machine table. Two webcams form a basis for the system, and constitute its characteristics. The proposed algorithm comprises various image processing techniques to assure a required...
-
Chemical and structural studies of screen-printed carbon electrodes (SPCE) with boron-doped diamond foils
Dane BadawczeThis dataset contains chemical analyses and structural studies by XPS and Raman spectroscopy, carried out for SPCE containing boron-doped diamond BDD foils done with scanning electron microscope. Different points for XPS analysis mark different electrode spots: A) working electrode, B) reference electrode, C) counter electrode, D) pads.
-
Endothelial Dysfunction Driven by Hypoxia—The Influence of Oxygen Deficiency on NO Bioavailability
PublikacjaCardiovascular diseases (CVDs) are the leading cause of death worldwide. The initial stage of CVDs is characterized by endothelial dysfunction, defined as the limited bioavailability of nitric oxide (NO). Thus, any factors that interfere with the synthesis or metabolism of NO in endothelial cells are involved in CVD pathogenesis. It is well established that hypoxia is both the triggering factor as well as the accompanying factor...
-
The effect of depth of surface layers constituted by vacuum technologies on pitting
PublikacjaThe paper presents the results of a study of the effect of vacuum technologies of formation of surface layers on pitting of associated elements in a lubricated, heavy-load rolling contact. The study has shown that increase in a PVD coat depth is accompanied by decrease in the fatigue friction pair.
-
A Robust Random Forest Model for Classifying the Severity of Partial Discharges in Dielectrics
PublikacjaPartial Discharges (PDs) are a common source of degradation in electrical assets. It is essential that the extent of the deterioration level of insulating medium is correctly identified, to optimize maintenance schedules and prevent abrupt power outages. Temporal PD signals received from damaged insulation, collected through the IEC-60270 method is the gold standard for PD detection. Temporal signals may be transformed to the frequency...
-
Ultra-Wideband Vivaldi Antenna with an Integrated Noise-Rejecting Parasitic Notch Filter for Online Partial Discharge Detection
PublikacjaPower transformers and gas-insulated switchgear (GIS) play crucial roles in electrical power grids. However, they may suffer from degradation of insulation material due to wear and tear, leading to their imminent failure. Partial discharges (PDs) are an initial sign of insulation materials degradation which emit signals spanning various physical domains, including electromagnetic. PDs are temporally narrow, high-frequency, stochastic...