Search
Filters
total: 9546
filtered: 8084
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: MARINE DIESEL ENGINE, FUEL INJECTOR GEOMETRY, COMBUSTION PROCESS, EXHAUST GAS COMPOSITION, EMISSION
-
INVESTIGATIONS OF THE LABORATORY FARYMANN DIESEL ENGINE D10 TYPE BY MEANS OF A LANGMUIR PROBE
PublicationA precise determination of the crankshaft angular position, at which fuel ignition occurs in the SI engine, enables credible diagnosis of the technical state of its working space as well as of the fuel feed system. An observation of the Langmuir probe signal provides entirely new possibilities for engine diagnostics. The probe is introduced into the working space of a cylinder through its indicator valve. This paper presents the...
-
Exhaust gas temperature measurements in diagnostic examination of naval gas turbine engines. Part I: Steady-state processes
PublicationThe article presents a possible method of detecting failures in the flow section and supply system of a naval gas turbine engine based on the exhaust gas temperature measured behind the gas generator. This temperature is a basic diagnostic parameter use for evaluating the technical state of the turbine engine in operation, and is monitored during engine start-ups, accelerations and decelerations of rotor units, and steady-load...
-
Analysis and Evaluation of the Working Cycle of the Diesel Engine
PublicationThe paper presents a proposal to apply a quantitative evaluation of the diesel engine with regard to the phenomena occurring during of a working cycle. The proposed procedure when analyzing test results from diesel engine is an attempt to transfer an engine activity evaluation methods in the operational time scale (exploit time), eg. in hours, to the micro-scale (dynamic time) relating only to the execution time of one (several)...
-
Compact High Efficiency and Zero-Emission Gas-Fired Power Plant with Oxy-Combustion and Carbon Capture
PublicationReduction of greenhouse gases emissions is a key challenge for the power generation industry, requiring the implementation of new designs and methods of electricity generation. This article presents a design solution for a novel thermodynamic cycle with two new devices—namely, a wet combustion chamber and a spray-ejector condenser. In the proposed cycle, high temperature occurs in the combustion chamber because of fuel combustion...
-
USE OF LANGMUIR PROBE IN DIESEL ENGINE DIAGNOSTIC RESEARCH Part I MEASUREMENT TECHNOLOGY. - Part 1 : MEASUREMENT TECHNOLOGY
PublicationIn the paper, the basic assumptions of diesel engine cylinder system's diagnosing method, based on observation of emerging and moving electric charges of ionized gas in the combustion workspaces, using Langmuir's probe. In the first part of the paper, only the technology of the measurement and results of the preliminary diagnostic tests of laboratory engine Farymann Diesel D10 were presented. The primary purpose of the research...
-
DESIGN ANALYSIS OF HYBRID GAS TURBINE - FUEL CELL POWER PLANT IN STATIONARY AND MARINE APPLICATIONS
PublicationThe paper concerns design analysis of a hybrid gas turbine power plant with a fuel cell (stack). The aim of this work was to find the most favorable variant of the medium capacity (approximately 50 MW) hybrid system. In the article, computational analysis of two variants of such a system was carried out. The analysis let to calculate capacity, efficiency of both variants and other parameters like flu gas temperature. The paper...
-
Process modeling inside cylinder in an internal combustion engine with heat regeneration
Publication -
Modeling of the internal combustion engine cooling system
PublicationThe article concerns computer modelling of processes in cooling systems of internal combustion engines. Modelling objectives and existing commercial programs are presented. It also describes Author’s own method of binding graphs used to describe phenomena in the cooling system of a spark ignition engine. The own model has been verified by tests on the engine dynamometer. An example of using a commercial program for experimental...
-
Stochastic model of the process of diesel engine operation.
PublicationStreszczenie: Najistotniejszym problemem eksploatacji silników o zapłonie samoczynnym jest problem racjonalnego (a zwłaszcza optymalnego) sterowania procesem eksploatacji tych silników. Sterowanie takie może ułatwić zastosowanie iteracyjnego algorytmu wyznaczania optymalnych strategii opracowanego przez R.A. Howarda. Wykorzystanie jednak tego algorytmu do sterowania procesem eksploatacji silników wymaga między innymi opracowania...
-
Simulation of ammonia combustion in dual-fuel compression-ignition engine
Publication -
Problems of modelling toxic compounds emitted by a marine internal combustion engine in unsteady states
PublicationContemporary engine tests are performed based on the theory of experiment. The available versions of programmes used for analysing experimental data make frequent use of the multiple regression model, which enables examining effects and interactions between input model parameters and a single output variable. The use of multi-equation models provides more freedom in analysing the measured results, as those models enable simultaneous...
-
Exhaust gas temperature measurements in diagnostic examination of naval gas turbine engines. Part III. Diagnostic and operating tolerances
PublicationThe third part of the article presents a method for detecting failures of the automatic engine control system with the aid of an exhaust gas temperature setter, specially designed and machined for this purpose. It also presents a procedure of identifying the operating tolerances and determining the diagnostic tolerances for the exhaust gas temperature recorded in the naval turbine engine during the start-up and acceleration processes....
-
Fault Tree Analysis and Failure Diagnosis of Marine Diesel Engine Turbocharger System
Publication -
Possible efficiency increasing of ship propulsion and marine power plant with the system combined of marine diesel engine, gas turbine and steam turbine
PublicationW rozdziale przedstawiono koncepcję układu kombinowanego okrętowego lub morskiej pływającej elektrowni dużej mocy złożonego z silnika głównego tłokowego oraz skojarzonych z nim turbiny gazowej mocy i układu turbiny parowej, wykorzystujących energię zawartą w spalinach wylotowych silnika głównego tłokowego. Rozpatrywano możliwości zastosowania takich układów w układach okrętowych z punktu widzenia sprawnościowego. Podano możliwości...
-
Planning of structure and range of preventive maintenance of marine diesel engine
PublicationPrzedstawiono sposób wyznaczania zasobów godzin pracy elementów złożonego obiektu technicznego na przykładzie okrętowego silnika spalinowego oraz planowania struktury i zakresu jego obsługi profilaktycznej.
-
The sources of contamination and reasons of damage of the flow part of the marine turbine engine in operation
PublicationThe aim of this paperis to show particular sensitivity of the flow part of the marine turbine engine to the presence of contaminations in the intake air. The contaminations form hard-to-remove deposits in the intervene channels that result in a reduced efficiency and performance of the engine. The paper classifies the contaminants according the source of their formation and their destructive force. The performed analyses and syntheses...
-
The influence of settable parameters of switching gasoline/LPG on exhaust toxic emissions
PublicationThe main objective of the studies shown in the paper was to develop a proper strategy for settable parameters of ECU to decrease total emission of toxic components in composition of exhaust during a cold start phase. The experimental research has been performed for engine running at idle and for engine running on the chassis dynamometer (performing European Driving Test NEDC).
-
The time of the first transition of the semi-Markov process in the evaluation of diesel engine operation
PublicationW referacie przedstawiono rozwinięcie prezentowanej w literaturze metody ilościowej oceny działania na przykładzie okrętowego silnika głównego z zapłonem samoczynnym. Według tej interpretacji, działanie silnika może zostać przedstawione jako wielkość fizyczna. W tym aspekcie, na przykładzie okrętowego silnika napędu głównego dokonano oceny przydatności tej wielkości do opisu własności niezawodnościowych silnika. Precyzyjne określenie...
-
Diagnostic tolerances' evaluation method of the start-up exhaust temperature of a naval gas turbine
PublicationThe conducted investigations aimed to elaborate the method of marking diagnostic tolerances of the exhaust temperature of a gas turbine observed during engine's start-up process. The diagnostic tolerances were determined by means of statistical inference by creating the hypothesis about a normal distribution of the start-up exhaust temperature's dispersion in the initial operation moment, which was subsequently verified applying...
-
Determination of fuel combustion product in airport runoff water samples using liquid–liquid extraction with gas chromatography–spectrometry
PublicationDetermination of xenobiotics in samples of airport runoff water is both a complex and indispensable task due to an increasing threat resulting from the activities of numerous airports. The aim of this study was to develop, optimize, and validate a procedure based on liquid–liquid extraction (LLE) coupled with gas chromatography–mass spectrometry (GC–MS) for the determination of polycyclic aromatic hydrocarbons (PAHs). So far, no...
-
Application of normal-phase high-performance liquid chromatography followed by gas chromatography for analytics of diesel fuel additives
PublicationThe paper presents the results of investigations on new procedures of determination of selected cleaning additives in diesel fuel. Two procedures: one-step analysis using gas chromatography with flame ionization detection (GC-FID) or mass spectrometry (GC-MS) and a two-step procedure in which normal-phase high-performance liquid chromatography (NP-HPLC) was used for preliminary separation of the additives, were compared. The additive...
-
Analysis of the Influence of Fuel Sulphur Content on Diesel Engine Particulate Emissions
Publication -
Dependence of the toxic components exhaust emission from the car engine starting temperature
PublicationW publikacji opisano wyniki badań empirycznych zależności stężeń toksycznych składników spalin od stanu cieplnego silnika w chwili rozruchu. Zwrócono uwagę na duże stężenia w pierwszych kilkudziesięciu sekundach po rozruchu. Badano silniki samochodów osobowych zarówno w eksploatacji jak i na hamowni podwoziowej.
-
Investigation of Exhaust Emissions from DI Diesel Engine During Cold and Warm Start
Publication -
Simplified method of water cooled exhaust system design.
PublicationThe water cooled exhaust systems are not often used onboard ships. Prime goal is to lower temperature of exhaust gas from main propulsion and auxiliary engines to the defined limit. The design of such systems require detailed analysis of propulsion system operational parameters to meet designer expectations. The paper outlines the cooled exhaust system design problems in specific application. The simplified method of evaluation...
-
Marine Fuel Sulphur Limit Impact on Air Pollution
PublicationThe article presents calculation of Sulphur oxides percentage drop rate in marine industry recorded after 01.01.2020 when new limits, provided by International Maritime Organizations legislation, became effective. Ships’ SOx global emission was estimated and compared between 4th quarter 2019 and 1st quarter 2020. For more accurate estimation 3 seaside cities with big harbors were selected for statistical analysis. Noticeable...
-
Possibilities of the performance improvement of the aero- and marine propulsion units equipped with combustion piston engines
PublicationWithin the paper there have been presented the authors' opinions concerning possibilities and needs of the performance optimization of the aero- and marine units powered by piston engines both of ''classic'' and contemporary construction. There have been also discussed the reserves contained within combustion piston engines which enable its performance improvement (the power and specific fuel consumption) as well as the fulfillment...
-
The Impact of Material Selection on Durability of Exhaust Valve Faces of a Ship Engine – A Case Study
Publicationwo alloys were used in order to extend the service life of marine engine exhaust valve head. Layers of cobalt base alloys were made of the powders with with chemical composition as follow: the layer marked L12; C-1,55%; Si-1,21%; Cr-29,7%; W-9%; Ni-2%; Mo<0,01%; Fe-1,7%; Co-54,83% and the layer marked N; C-1,45%; Co-38,9%; Cr-24,13%; Ni-10,43%; W-8,75%; Fe-7,64%; Mo-7,56%; Si-2,59%. Base metal was valve steel after heat treatment....
-
Evaluation of methods for determining the combustion ignition delay in a diesel engine powered by liquid biofuel
Publication -
Exergy analysis of a negative CO2 emission gas power plant based on water oxy-combustion of syngas from sewage sludge gasification and CCS
PublicationA power cycle with water-injected oxy-combustion (water cycle) is investigated by exergy analysis. It is fueled with syngas (aka. producer gas) from gasification of sewage sludge. The cycle is equipped with a spray-ejector condenser (SEC). CO2 is separated and compressed for transportation and storage. The net delivered electric power is 31% of the fuel exergy. The task efficiency is 39% when the flue gas bleed to gasification...
-
Experiments on compression ignition engine powered by nano-fuels
PublicationThe use of nanoparticles in fuels provides new opportunities for modification of fuel properties, which may affect the operational parameters of engines, in particular the efficiency and fuel consumption. The paper presents comparison of compression ignition engine performance fuelled with neat diesel and nano-diesel. Alumina (Al2O3) was used as nanoparticles. Surface-active substances, including Span 80 surfactant, as well as...
-
The Staged Combustion of Meat-and-Bone Meal:The Characteristics of Conversion Sub-processes and Large-Scale Process Outputs
Publicationt Organic waste has been playing an increasingly important role in the energy market as those that may support the economies in pursuing towards decarbonization by increasing the share of renewables in the overall energy balance. In this group of alternative fuels, meat-and-bone meals being a post-production waste of the steadily developing meat industry, constitute a considerable proportion. Though they are rich in minerals, their...
-
Evaluation of compression realization in diesel engine based on performance indicator changes
PublicationIn the article a method of evaluation of a diesel engine during the realization of processes of working cycle on the example of compression is described. The method is based on the use of the quantity called performance indicator in the description of the engine's work, which contains the information on the energy values, which may be disposed using the engine and the time at which it can be delivered. Theoretical information has...
-
Exhaust Emission from Passenger Cars During Engine Cold Start and Warm-Up
Publication -
Experimental study of the fuel jet combustion in high temperature and low oxygen content exhaust gases
PublicationPrzeprowadzono badania eksperymentalne spalania pojedynczego strumienia paliwa gazowego. Paliwo podawano współosiowo do generowanych przez konwencjonalny palnik gazowy spalin o wysokiej temperaturze i niskiej zawartości tlenu. Badano wpływ zawartości tlenu w utleniaczu na widzialność płomienia i skład produktów spalania.
-
Energetuc aspect of diesel engine operotion
PublicationW artykule zaproponowano interpretację wartościującą działania, które (podobnie jak przedstawione mechanice klasycznej działania Hamiltona i Maupertiusa oraz działanie wynikające ze zmiany pędu ciała) jest rozpatrywane jako wielkość fizyczna o jednostce miary zwanej dżulosekundą [dżulsekunda]. Przedstawiono oryginalną metodę analizy i oceny działania silników o zapłonie samoczynnym w ujęciu energetycznym dla potrzeb eksploatacyjnych....
-
The concept of research on ecological, energy and reliability effects of modified marine fuel oils application to supply compression-ignition engines in real conditions
PublicationWithin the article, basic assumptions of the research project financed by Regional Fund for Environmental Protection and Water in Gdansk were described. The project concerns the experimental investigations carried out on laboratory compression-ignition engine in conditions of its supply with a non-standard marine fuel oil. Configuration and measuring capability of laboratory test bed presently being constructed were introduced....
-
Quantumness in Diagnostics of Marine Internal Combustion Engines and Other Ship Power Plant Machines
PublicationThe article provides proof that the diagnostics of marine internal combustion engines and other ship power plant machines should take into account the randomness and unpredictability of certain events, such as wear, damage, the variations of mechanical and thermal loads, etc., which take place during machine operation. In the article, the energy E, like the other forms (methods) that it can be converted into (heat and work), is...
-
On the possible increasing of efficiency of ship power plant with the system combined of marine diesel engine, gas turbine and steam turbine at the main engine - steam turbine mode of cooperation
PublicationW pracy przedstawiono koncepcję układu kombinowanego okrętowego dużej mocy złożonego z silnika głównego tłokowego oraz skojarzonych z nim turbiny gazowej mocy i układu turbiny parowej, wykorzystujących energię zawartą w spalinach wylotowych silnika głównego tłokowego. Rozpatrywano układ kombinowany układ złożony z silnika spalinowego tłokowego skojarzony z układem turbiny parowej. Podano algorytm i obliczenia poszczególnych podukładów:...
-
On the possible increasing of efficiency of ship power plant with the system combined of marine diesel engine, gas turbine and steam turbine in case of main engine cooperation with the gas turbine fed in parallel and the steam turbine
PublicationW pracy przedstawiono koncepcję układu kombinowanego okrętowego dużej mocy złożonego z wiodącego silnika głównego spalinowego silnika tłokowego i skojarzonych z nim turbiny gazowej mocy i układu turbiny parowej, wykorzystujących energię zawartą w spalinach wylotowych głównego silnika spalinowego. Rozpatrzono wariant układu kombinowanego, w którym główny jest silnik tłokowy skojarzony z turbiną gazową mocy i układem turbiny parowej,...
-
On the possible increasing of efficiency of ship power plant with the system combined of marine diesel engine, gas turbine and steam turbine in case of main engine cooperation with the gas turbine fed in series and the steam turbine
PublicationW pracy przedstawiono koncepcję układu kombinowanego okrętowego dużej mocy złożonego z wiodącego silnika głównego silnika spalinowego tłokowego oraz skojarzonych z nim turbiny gazowej mocy i układu turbiny parowej, wykorzystujących energię zawartą w spalinach wylotowych silnika spalinowego. Rozpatrywano wariant układu kombinowanego, którym turbina mocy jest zasilana szeregowo spalinami wylotowymi. Podano algorytm i obliczenia...
-
Turning process monitoring of internal combustion engine piston’s cylindrical surface
Publication -
Model of process of wear sidle bearings of self ignition combustion engine
PublicationW artykule została podjęta próba przeanalizowania praktycznej przydatności modelu procesu zużycia głównych łożysk ślizgowych silnika spalinowego o ZS, opisującego zmienną szybkość ich zużycia. Analizie został poddany problem częstych zatrzymań i rozruchów silnika, gdyż z badań statystycznych wynika, że w tym czasie występuje największe zużycie łożysk ślizgowych.
-
Gas corrosion influence on the exhaust valve face of the marine engine = Wpływ korozji gazowej na stan przylgni zaworów wylotowych silnika okrętowego
PublicationIstotnym czynnikiem wpływającym na poprawność funkcjonowania silnika okrętowego jest szczelność zaworów. Szczególnie w odniesieniu do zaworów wylotowych brak szczelności prowadzi do pogorszenie warunków spalania a przede wszystkim do przyspieszonego zniszczenia zawory poprzez uszkodzenia przylgni.Przylgnia grzybka zaworowego współpracuje z przylgnią gniazda zaworowego tworząc cykliczny szczelny kontakt stykowy w trakcie pracy silnika....
-
Flexible syngas-biogas-hydrogen fueling spark-ignition engine behaviors with optimized fuel compositions and control parameters
PublicationThis paper presents the results research on the optimal fuel compositions and the control parameters of the spark ignition engine fueled with syngas-biogas-hydrogen for the purpose of setting up a flexible electronic control unit for the engine working in a solar-biomass hybrid renewable energy system. In syngas-biogas-hydrogen mixture, the optimal content of hydrogen and biogas is 20% and 30%, respectively. Exceeding these thresholds,...
-
Thermal utilization of meat and bone meals. Performance analysis in terms of drying process, pyrolysis and kinetics of volatiles combustion
PublicationA development of technology of thermal utilization requires a thorough knowledge of the physicochemical properties, as well as kinetics of combustion of volatiles and char. Due to waste management regulations the meat and bone meal (MBM) is regarded as biofuel constituting one of the alternatives to fossil fuels in the energy market. MBM is a heterogeneous material that may consist of several different fractions. The extensive...
-
HEALTH MONITORING OF A COMPRESSION IGNITION ENGINE FED WITH DIFFERENT LOW-SULPHUR MARINE FUELS BY ENDOSCOPIC IMAGE PROCESSING AND ANALYSIS
PublicationThis article characterises the methodology for the endoscopic testing of a laboratory diesel engine used for testing marine fuels. The ‘Shadow’ measurement method used in the XLG3 type EVEREST digital endoscope, for quantitative and qualitative identification of detected surface defects, was approximated. Representative endoscopic images of the elements limiting the working space of the research engine are demonstrated, having...
-
Analysis of the possibilities of using of DME fuel in motor boat drive systems
PublicationThe characteristics of alternative fuel for diesel: dimethyl ether (DME) and an analysis of the potential to reduce emissions of toxic compounds by the engines when running on this fuel have been presented in this work. Basic types of design solutions of gas supply and control systems, possible for use in internal combustion engines with DME supply have been also presented. The paper presents a study of the legislation and an analysis...
-
APPLICABILITY OF INLET AIR FOGGING TO MARINE GAS TURBINE
PublicationThe dependency of marine gas turbine on the ambient temperature leads to a decrease of the gas turbine power output in arid areas. Very often gas turbine power output demand is high and the power margins originally designed into the driver , has been exhausted. In such circumstances the inlet air fogging is an effective compensation of gas turbine power. In this paper an analysis of inlet air fogging applicability to marine gas...
-
Experimental determination of general characteristic of internal combustion engine using mobile test bench connected via Power Take-Off unit
PublicationThe general characteristics of the engine include information about the regions of the engine's operating area that are most efficient, where specific fuel consumption reaches the smallest values. Economic operation based on those characteristics can contribute to a significant reduction of fuel consumption and consequently less pollutant emissions and lower costs. The paper presents an experimental method of determination of general...