Filters
total: 159
filtered: 154
-
Catalog
Chosen catalog filters
Search results for: MULTI-STAGE AXIAL TURBINE
-
Experimental ORC micro-power plant for CHP application Part B: Radial and Multi-stage axial turbines
PublicationThe co-generative micro-power plant with the HFE7100 applied as a working medium was designed and built for experimental investigations. Special attention is paid to a micro-turbine which was built and tested in two variants: a radial turbine and an axial turbine. A concept of a radial turbine with 2 centripetal and 2 centrifugal stages is shown. This prototype was equipped with an aerostatic gas bearing and, alternatively, with...
-
The influence of rotor-stator axial gap on the aerodynamic forces generatedin the shroud clearance of a turbine stage. Part I: Pressure field
PublicationPrzedstawiono wyniki badań doświadczalnych wpływu zmiany luzu osiowego na rozkład ciśnienia w uszczelnieniu nadbandażowym stopnia powietrznej turbiny modelowej. Wykazano, że w przypadku uszczelnienia promieniowego zmiana luzu osiowego nieznacznie zmienia rozkład ciśnienia w szczelinie nadbandażowej w porównaniu ze zmianą mimośrodowości czy skośnego ustawienia osi wirnika względem osi korpusu.
-
The influence of rotor-stator axial gap on the aerodynamic forces generatedin the shroud clearance of a turbine stage. Part II: Forces and moments
PublicationPrzedstawiono wyniki badań doświadczalnych wpływu zmiany luzu osiowego na wymuszenia aerodynamiczne powstające w uszczelnieniu nadbandażowym stopnia powietrznej turbiny modelowej. Wykazano, że w przypadku uszczelnienia promieniowego zmiana luzu osiowego odgrywa niewielką rolę w generowaniu sił i momentów aerodynamicznych w szczelinie nadbandażowej w porównaniu ze zmianą mimośrodowości czy skośnego ustawienia osi wirnika względem...
-
Multi-objective optimization of the ORC axial turbine for a waste heat recovery system working in two modes: cogeneration and condensation
PublicationDue to the demand of the district heating network and electric power grid ORC turbines can operate in the condensation and cogeneration modes. This approach requires the design of an expander which is characterized by high efficiency in each mode of operation. The paper is devoted to a multi-objective efficiency optimization of a one stage axial ORC turbine working on MM (Hexamethyldisiloxane). An Implicit Filtering algorithm (IF)...
-
Example of Using Particle Swarm Optimization Algorithm with Nelder–Mead Method for Flow Improvement in Axial Last Stage of Gas–Steam Turbine
PublicationThis article focuses principally on the comparison baseline and the optimized flow efficiency of the final stage of an axial turbine operating on a gas–steam mixture by applying a hybrid Nelder– Mead and the particle swarm optimization method. Optimization algorithms are combined with CFD calculations to determine the flowpaths and thermodynamic parameters. The working fluid in this study is a mixture of steam and gas produced...
-
Example of Using Particle Swarm Optimization Algorithm with Nelder–Mead Method for Flow Improvement in Axial Last Stage of Gas–Steam Turbine
Publication -
High-speed multi-stage gas-steam turbine with flow bleeding in a novel thermodynamic cycle for decarbonizing power generation
PublicationIn the global pursuit of sustainable energy and reduced carbon footprints, advances in power generation techniques play a crucial role, not only in meeting the ever-increasing energy demands but also in ensuring that environmental standards are maintained and that the health of our planet is prioritized for future generations. In the ongoing quest for sustainable energy solutions, novel high-speed multi-stage gas-steam turbine...
-
A multistage turbine for a micro power plant
PublicationThis paper presents results of a design analysis of a multi-stage turbine for the cogeneration micro-power plant working in accordance with Organic Rankine Cycle (ORC). The heat power of the plant is assumed equal to 20 kW and the corresponding available electric output is estimated to be of about 3 kW. Different variants of the radial and axial-flow turbines have been considered, while the detailed results of the calculations...
-
Design and investigations of a micro-turbine flow part
Publication-generative micro-power plant with the HFE7100 as a working medium was designed and built for experimental investigations. The heat output of the plant was assumed equal to 20 kW, while the electric output amounted to about 3kW.In the paper a multi-stage micro-turbine with partial admission of all the stages is described in detail and the results of the particular experimental investigations and numerical calculations are shown,...
-
DESIGN ANALYSIS OF HYBRID GAS TURBINE - FUEL CELL POWER PLANT IN STATIONARY AND MARINE APPLICATIONS
PublicationThe paper concerns design analysis of a hybrid gas turbine power plant with a fuel cell (stack). The aim of this work was to find the most favorable variant of the medium capacity (approximately 50 MW) hybrid system. In the article, computational analysis of two variants of such a system was carried out. The analysis let to calculate capacity, efficiency of both variants and other parameters like flu gas temperature. The paper...
-
Impact of rotor geometry optimization on the off-design ORC turbine performance
PublicationThe paper describes the method of CFD based Nelder-Mead optimization of a 10 kW single-stage axial turbine operating in an ORC system working on R7100. The total-to-static isentropic efficiency is defined as an objective function. Multi-point linear regression is carried out to determine the significance of the objective function arguments and to pick up the set of particular variables and characteristic quantities (e.g. flow angles)...
-
OPTIMIZATION OF THE LAST STAGE OF GAS-STEAM TURBINE USING A HYBRID METHOD
PublicationThis paper relates to the CFD calculation of a new turbine type which is in the phase of theoretical analysis, because the working fluid is a mixture of steam and gas generated in wet combustion chamber. At first, this article concentrates on a possibility of streamlining the flow efficiency of a last stage of axial turbine working on gas-steam mixture using a hybrid of the particle swarm optimization algorithm with the Nelder-Mead...
-
Revalorisation of the Szewalski’s concept of the law of varying the last-stage blade retraction in a gas-steam turbine
PublicationThe article presents the implementations of the free vortex law to the blade of the last stage of a gas-steam turbine. First, a thermodynamic analysis was carried out, determining the parameters at the inlet, then the number of stages of the high and low-pressure part of the turbine was constructed, together with the kinematics and velocity vectors for subsequent stages of the axial turbine. The last step of article was to take...
-
Some Aspects of Designing Nozzle Segments of Axial Microturbines,
PublicationIn the paper a multi-stage micro-turbine with partial admission of all the stages is described in detail and the results of the numerical calculations and experimental investigations are presented, followed by an appropriate discussion and conclusions.
-
Investigations of the Working Process in a Dual-Fuel Low-Emission Combustion Chamber for an FPSO Gas Turbine Engine
PublicationThis investigation is devoted to an analysis of the working process in a dual-fuel low-emission combustion chamber for a floating vessel’s gas turbine. The low-emission gas turbine combustion chamber with partial pre-mixing of fuel and air inside the outer and inner radial-axial swirlers was chosen as the object of research. When modelling processes in a dual-flow low-emission gas turbine combustion chamber, a generalized method...
-
Domestic ORC micro-CHP combined with a commercial gas boiler
PublicationThe chapter presents the results of experimental studies conducted during the launch of the first in Poland demonstration prototype of the micro ORC coupled to a domestic gas boiler. The accomplished studies indicated the possibility for the ORC module to work with such boiler (autonomous source of heat) with a prototype single-stage axial micro turbine as the expansion machine. Confirmation of that fact has been delineated in...
-
Study on the Influence of an Axial Distance Between Rotors on a Performance of a Small Counter-Rotating Wind Turbine
PublicationIn this paper, results of the investigation on the performance of a small counter-rotating wind turbinehas been presented. Computational Fluid Dynamics methodshave been used forwind turbine simulations. Rotors representation were introduced into computational domain by means of Actuator Line Model. Influence of an axial distance of CRWTrotorshas been investigated. In all studied configurations rotors were counter-rotating...
-
Axial-Flux Permanent-Magnet Dual-Rotor Generator for a Counter-Rotating Wind Turbine
PublicationCoaxial counter-rotating propellers have been widely applied in ships and helicopters for improving the propulsion efficiency and offsetting system reactive torques. Lately, the counter-rotating concept has been introduced into the wind turbine design. Distributed wind power generation systems often require a novel approach in generator design. In this paper, prototype development of axial-flux generator with a counter-rotating...
-
The use of plate springs for preloading of a system of tapered roller bearings of a wind turbine gearbox
PublicationThe use of preloaded tapered roller bearings in wind turbine drive systems allows a transfer of load in the case of high variations of axial forces. The examined bearing system, a modification of a current design, consists of a pair of different sized bearings. Previous study showed the high sensitivity of tapered roller bearings on the existing radial interference. Dimensional tolerances used in the original design do not allow...
-
INVESTIGATION OF THE CHARACTERISTICS OF A LOWEMISSION GAS TURBINE COMBUSTION CHAMBER OPERATING ON A MIXTURE OF NATURAL GAS AND HYDROGEN
PublicationT his article is devoted to the investigation of the characteristics of a low-emission gas turbine combustion chamber, which can be used in Floating Production, Storage and Offloading (FPSO) vessels and operates on a mixture of natural gas and hydrogen. A new approach is proposed for modelling the processes of burning out a mixture of natural gas with hydrogen under preliminary mixing conditions in gaseous fuel with an oxidizer...
-
INVESTIGATIONS OF THE EMISSION CHARACTERISTICS OF A DUAL-FUEL GAS TURBINE COMBUSTION CHAMBER OPERATING SIMULTANEOUSLY ON LIQUID AND GASEOUS FUELS
PublicationT his study is dedicated to investigations of the working process in a dual-fuel low-emission combustion chamber for a floating vessel’s gas turbine. As the object of the research, a low-emission gas turbine combustion chamber with partial premixing of fuel and air inside the outer and inner radial-axial swirls was chosen. The method of the research is based on the numerical solution of the system of differential...
-
Parametric Study on a Performance of a Small Counter-Rotating Wind Turbine
PublicationA small Counter-Rotating Wind Turbine (CRWT) has been proposed and its performancehas been investigated numerically. Results of a parametric study have been presented in this paper.As parameters, the axial distance between rotors and a tip speed ratio of each rotor have been selected.Performance parameters have been compared with reference to a Single Rotor Wind Turbine (SRWT).Simulations were carried out with Computational Fluids...
-
Different design aspects of an Organic Rankine Cycle turbine for electricity production using a geothermal binary power plant
PublicationIn recent years, pressure has been growing to increase the share of renewable energy sources in electricity generation, which may offer opportunities for the development of geothermal energy in regions that have been so far considered unprofitable in this respect. One such country currently undergoing an energy transition is Poland in which low-temperature geothermal resources are currently used for district heating and recreation...
-
Partial Admission Stages of High Efficiency for a Microturbine
PublicationThe paper presents the results of a design analysis of a micro-turbine for a co-generation micro-power plant working in accordance with organic Rankine cycle. The heat power of the plant is assumed equal to 20kW and the corresponding available electric output is estimated to be about 3kW. After the design analysis, the axial turbine with partial admission in all stages was built and tested experimentally. Special attention was...
-
THE INFLUENCE OF HOUSING ARRANGEMENT AND INTERFERENCE ON PRELOAD AND THEORETICAL LIFETIME OF A SYSTEM OF TAPER ROLLER BEARINGS OF A HIGH SPEED SHAFT OF A WIND TURBINE GEARBOX
PublicationA system of two taper roller bearings can carry loads with a high ratio of axial load to radial load. Such a system was proposed for a wind turbine gearbox following the poor durability of original bearing design with the aim of increasing durability. Because of size limits, a proposed system is composed of two different taper roller bearings. Standard manufacturers’ catalogues do not provide information on recommended preload...
-
Partial Admission Stages of High Efficiency for a Microturbine
PublicationThe paper presents the results of a design analysis of a microturbine for a cogeneration micro-power plant working in accordance with organic Rankine cycle. The heat power of the plant is assumed equal to 20kW and the corresponding available electric output is estimated to be about 3 kW. After the design analysis, the axial turbine with partial admission in all stages was built and tested experimentally. Special attentionwas paid...
-
Analysing selection of low-temperature medium for cogeneration micro power plant
PublicationThe article analyses the ORC system working with dry and wet low-boiling media which are most frequently used in installations of this type. Two types of cycles were examined, which were the cycle with heat regeneration for dry media: fc72, hfe7100, R227ea, R245fa, R423a and R600a, and the cycle without heat regeneration for wet media: R11, R12, R134a, R718 and 507a. The calculations were performed for the assumed required thermal...
-
Analysing selection of low-temperature medium for cogeneration micro power plant
PublicationThe article analyses the ORC system working with dry and wet low-boiling media which are most frequently used in installations of this type. Two types of cycles were examined, which were the cycle with heat regeneration for dry media: fc72, hfe7100, R227ea, R245fa, R423a and R600a, and the cycle without heat regeneration for wet media: R11, R12, R134a, R718 and 507a. The calculations were performed for the assumed required thermal...
-
Neural Modelling of Steam Turbine Control Stage
PublicationThe paper describes possibility of steam turbine control stage neural model creation. It is of great importance because wider application of green energy causes severe conditions for control of energy generation systems operation Results of chosen steam turbine of 200 MW power measurements are applied as an example showing way of neural model creation. They serve as training and testing data of such neural model. Relatively simple...
-
Kinetic analysis of the stage for a high speed steam turbine
PublicationThis article analyzes possibilites of resonances within a control stage for a high speed steam turbine. This stage hase been based on assembling of a single blade to a rotating disk and increasing of rigidity of the system by using of a bandage. In the analysis will be nd a possiblity of resonance frequency, and mistuning by showing safety working ranges. The calculations have bean used the3D modal and harmonic analysis by the...
-
On design and analysis of flow characteristics of the last stage of gas-steam turbine
PublicationResearch regarding blade design and analysis of flow have been conducted for over a century. Meanwhile new concepts and design approaches were created and improved. Advancements in information technologies allowed to introduce computational fluid dynamics (CFD) and computational flow mechanics (CFM). Currently a combination of mentioned methods is used for design of turbine blades. These methods enabled us to improve flow efficiency...
-
Organic Rankine cycle as bottoming cycle to a combined Brayton and Clausius - Rankine cycle
PublicationA preliminary evaluation has been made of a possibility of bottoming of a conventional Brayton cycle cooperating with the CHP power plant with the organic Rankine cycle installation. Such solution contributes to the possibility of annual operation of that power plant, except of operation only in periods when there is a demand for the heat. Additional benefit would be the fact that an optimized backpressure steam cycle has the advantage...
-
On the internal efficiency of a turbine stage: classical and CFD definitions
PublicationAlmost entire fleet of steam turbines in Poland was designed between 1950 – 1980 with the use of the so-called zero dimensional (0D) calculation tools. For several years, design and modernization of the turbines occur in assistance with the state of the art methods that describe working fluid flow field based on 3D models and CFD codes. This cooperation between 0D and 3D codes requires exchange of overall, integral information...
-
Thermal failure of a second rotor stage in heavy duty gas turbine
PublicationThe impulse mode of operation and the supply of various types of fuels causes frequent failures even in the heavy duty gas turbines. The paper presents the ravages of second rotor stage failure in a gas turbine. The excessive thermal elongation rise caused by fuel change was indicated as the main cause. We applied nonlinear numerical analysis, preceded by thermodynamic calculations of the turbine and visual inspection of the effects...
-
Design and computational fluid dynamics analysis of the last stage of innovative gas-steam turbine
PublicationResearch regarding blade design and analysis of flow has been attracting interest for over a century. Meanwhile new concepts and design approaches were created and improved. Advancements in information technologies allowed to introduce computational fluid dynamics and computational flow mechanics. Currently a combination of mentioned methods is used for the design of turbine blades. These methods enabled us to improve flow efficiency...
-
OBTAINING FLUID FLOW PATTERN FOR TURBINE STAGE WITH NEURAL MODEL.
PublicationIn the paper possibility of applying neural model to obtaining patterns of proper operation for fluid flow in turbine stage for fluid-flow diagnostics is discussed. Main differences between Computational Fluid Dynamics (CFD) solvers and neural model is given, also limitations and advantages of both are considered. Time of calculations of both methods was given, also possibilities of shortening that time with preserving the accuracy...
-
Preliminary design of the last stage of supercritical steam turbine and proposition of anti-erosion coating for blades surface
PublicationIn this article a preliminary design of the last stage of supercritical steam turbine has been presented. A computational model of supercritical thermal cycle has been created in order to determine steam parameters at the stage inlet and outlet. The model was based on the structure of German coal-fired power plant Datteln 4. Further steam-flow parame-ters and dimensions of stator and rotor blades have been calculated analytically....
-
Multi-Stage Video Analysis Framework
Publication -
Multi-Stage Video Analysis Framework
PublicationThe chapter is organized as follows. Section 2 presents the general structure of the proposed framework and a method of data exchange between system elements. Section 3 is describing the low-level analysis modules for detection and tracking of moving objects. In Section 4 we present the object classification module. Sections 5 and 6 describe specialized modules for detection and recognition of faces and license plates, respectively....
-
Turbine stage design aided by artificial intelligence methods
PublicationZaproponowano ogólny, wydajny system wspomagania projektowania palisad , stopni i grupy stopni turbinowych. Zastosowane algorytmy wykorzystują algorytmy genetyczne, sieci neuronowe i obliczenia równoległe. Uzyskane rozwiązania projektowe są wysoko zoptymalizowane pod względem sprawności, a czas ich uzyskania jest o kilka rzędów wielkości mniejszy, niż przy zastosowaniu obliczeń CFD.
-
Reliable Multi-Stage Optimization of Antennas for Multiple Performance Figures in Highly-Dimensional Parameter Spaces
PublicationDesign of modern antenna structures needs to account for multiple performance figures and geometrical constraints. Fulfillment of these calls for the development of complex topologies described by a large number of parameters. EM-driven tuning of such designs is mandatory yet immensely challenging. In this letter, a new framework for multi-stage design optimization of multi-dimensional antennas with respect to several performance...
-
Multi-stage magnetic-fluid seals for operating in water - life test procedure, test stand and research results. Part II Results of life tests of multi-stage magnetic - fluid seal operating in water
PublicationThe edge criteria for magnetic-fluid seals durability research were described in previous article [24] and now the tests results are presented. The tests were made with three magnetic fluids using various magnets quantity in magnetic assemblies. If values obtained in the repeated test deviated by more than 10 % from results of the first test an additional control test was made for final characteristics. The characteristics are:...
-
Multi-stage magnetic-fluid seals for operating in water - life test procedure, test stand and research results
PublicationThe edge criteria for magnetic-fluid seals durability research are critical for the seal'stechnological usefulness. The magnetic fluid seal technology in water is much moredifficult technological problem in comparison to gas or vacuum environment. There isalways problem with immediate contact between magnetic fluid and the environmentaluninspected liquids. In the paper are presented ways of experiments definitions carried outwith...
-
Optimization of an axial turbine for a small scale ORC waste heat recovery system
Publication -
Monitoring the gas turbine start-up phase on the platform using a hierarchical model based on Multi-Layer Perceptron networks
PublicationVery often, the operation of diagnostic systems is related to the evaluation of process functionality, where the diagnostics is carried out using reference models prepared on the basis of the process description in the nominal state. The main goal of the work is to develop a hierarchical gas turbine reference model for the estimation of start-up parameters based on multi-layer perceptron neural networks. A functional decomposition...
-
Theoretical and experimental flow analysis through the model water turbine stage
PublicationW artykule zaprezentowano teoretyczną i eksperymentalną analizę przepływu przez stopień modelowej turbiny wodnej. Przedstawiono rozwiązanie zadania prostego dla dwuwymiarowego modelu przepływu. Zaprezentowano przykład numerycznej symulacji przepływu za pomocą komeryjnych kodów obliczeniowych oraz porównano wyniki symulacji numerycznych przepływu z wynikami badań eksperymentalnych.
-
Modelling of the Baumann turbine stage operation Part II. Free and kinetic vibrations
PublicationIn this paper has been presented a methodology of validation a novel mathematical model dedicated to evaluation and prediction of material degradation and demage of steam turbine elements such as blades, valves and pipes due to three mechanisms: stress-corosion, high-temperature creep and low-cyclic fatigue. The validation concept is based on an experimental setup manufactured in the Laboratory of Faculty of Mechanical and Power...
-
Compact scheduling of zero–one time operations in multi-stage systems
Publication -
Compact scheduling of zero-one time operations in multi-stage systems.
PublicationRozważamy szeregowanie zwarte na maszynach dedykowanych z zero-jedynkowymi operacjami w modelu otwartym, przepływowym i mieszanym. Harmonogramy zostały zmodelowane przy pomocy pokolorowań krawędzi grafu konfliktów z pewnymi dodatkowymi ograniczeniami. Dowodzimy NP-trudności problemów w przypadku ogólnym oraz prezentujemy przegląd znanych wielomianowych algorytmów szeregujących dla systemów o specyficznej budowie.
-
Towards an efficient multi-stage Riemann solver for nuclear physics simulations
PublicationRelativistic numerical hydrodynamics is an important tool in high energy nuclear science. However, such simulations are extremely demanding in terms of computing power. This paper focuses on improving the speed of solving the Riemann problem with the MUSTA-FORCE algorithm by employing the CUDA parallel programming model. We also propose a new approach to 3D finite difference algorithms, which employ a GPU that uses surface memory....