Search results for: SLIDING TABLE SAW
-
Marine propeller shaft bearings under low-speed conditions: water vs. oil lubrication
PublicationThe bearings used in shipbuilding, hydropower, and water pumps have undergone a metamorphosis in recent decades. Because of environmental regulations, lubrication with grease or mineral oil is prohibited. Thus, the standard solutions include water-lubricated bearings with polymer bushings or sealed systems lubricated with oil. When properly designed, assembled, and operated, bearings can operate reliably for years. However, specific...
-
Effect of plasma sprayed and laser re-melted Al2O3 coatings on hardness and wear properties of stainless steel
PublicationCommercially available austenic stainless steel substrate was coated with commercially available, raw Al2O3 powder applied by means of plasma spraying method and then re-melted with CO2 laser beam of various parameters. Tribological and mechanical properties of the 120 J/mm and 160 J/mm laser re-melted coatings were compared with the tribological and mechanical properties of the “as-sprayed” coating. The influence of the laser...
-
The experience of movement in the built form and space: A framework for movement evaluation in architecture
Publication“Movement in architecture” is an organized system of various types of movements stimulated by specific architectural elements. This research was conducted through a qualitative-analytical method and empirical and bibliographical research methods with the aim to categorize different types of movements based on the explorer and observer relationships with the built space and form. So far, most of the related studies have focused...
-
Experimental and Numerical Study on Pounding of Structures in Series
PublicationPounding between structures in series during earthquakes may cause serious damage in the structural elements. The aim of this paper is to show the results of an experimental and numerical study that is focused on pounding between more than two structures which may be described as “structures in series”. In this study, the shaking table experiments, as well as the numerical analyses, were performed using three tower models including...
-
Review of the Usefulness of Various Rotational Seismometers with Laboratory Results of Fibre-Optic Ones Tested for Engineering Applications
PublicationStarting with descriptions of rotational seismology, areas of interest and historical field measurements, the fundamental requirements for rotational seismometers for seismological and engineering application are formulated. On the above basis, a review of all existing rotational seismometers is presented with a description of the principles of their operation as well as possibilities to fulfill formulated requirements. This review...
-
Projektowanie urbanistyczne III - Osowa-Nowy Świat 2021/22
e-Learning CoursesProjektowanie urbanistyczne III - Osowa-Nowy Świat 2021/22 Piątek 10.15-13.00 – sala 306 Prowadzący: dr hab. inż. arch. J. Martyniuk – Pęczek, prof. PG mgr inż. arch. M. Waczyńska
-
WETI - EiT - Matematyka - sem.2 - 2021/2022 (N.Jarzębkowska)
e-Learning CourseseKurs wykładowy dla przedmiotuAnaliza matematyczna II dla kierunku Elektronika i Telekomunikacja (sem. 2) Wydziału Elektroniki, Telekomunikacji i Informatyki
-
Mostowe Konstrukcje Stalowe i Zespolone - 2022/23
e-Learning CoursesZagadnienia teoretyczne a rzeczywista konstrukcja. Rzeczywista praca elementów mostów stalowych (węzły, połączenia, usztywnienia). Mosty blachownicowe Mosty zespolone (stal–beton). Mosty kratownicowe Mosty Łukowe Mosty podwieszone Mosty wiszące Zasady konstruowania Detale konstrukcyjne Elementy wyposażenia mostów
-
WETI - EiT gr.1,2 - Matematyka - sem.2 - 2021/2022 (N.Jarzębkowska)
e-Learning CourseseKurs do ćwiczeń dla przedmiotuAnaliza matematyczna II dla kierunku Elektronika i Telekomunikacja (sem. 2) Wydziału Elektroniki, Telekomunikacji i Informatyki
-
Mostowe Konstrukcje Stalowe i Zespolone - 2023/24
e-Learning CoursesZagadnienia teoretyczne a rzeczywista konstrukcja. Rzeczywista praca elementów mostów stalowych (węzły, połączenia, usztywnienia). Mosty blachownicowe Mosty zespolone (stal–beton). Mosty kratownicowe Mosty Łukowe Mosty podwieszone Mosty wiszące Zasady konstruowania Detale konstrukcyjne Elementy wyposażenia mostów
-
Inżynieria Reaktorów Chemicznych
e-Learning CoursesInżynieria reaktorów chemicznych (PG_00035169)
-
Thickness accuracy of sash gang sawing
PublicationThin lamellae, corresponding to the layer components of structural glued members, i.e. 2-ply or 3-ply glued parquet, can be manufactured in re-sawing operations of kiln-dried wood blocks. These must be prepared with high dimensional accuracy and adequate surface quality following specific technical requirements for lamellae thickness variations, especially in the upper layers of the glued composite parquet. The accuracy of oak...
-
AN ALTERNATIVE WAY OF DETERMINING MECHANICAL PROPERTIES OF WOOD BY MEASURING CUTTING FORCES
PublicationThe cutting force is an energetic effect of splitting material, and might be therefore considered from a point of view of modern fracture mechanics. The dedicated mathematical model developed for description of the wood cutting has been developed here on the base of fracture theory, and includes work of separation (fracture toughness) in addition to the material plasticity and friction. The effect of the cutting edge dullness is...
-
Wear in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). No lubrication (DRY). Specim. set K01
Open Research DataFriction and wear tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: DRY. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180 and 300s. (stored in separate folders).Specimen...
-
Wear in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - PARAFFIN OIL. Specim. set K09 - full run
Open Research DataFriction and wear tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: PARAFFIN OIL. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180 and 300s. (stored in separate...
-
Wear in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - DISTILLED WATER. Specim. set K06
Open Research DataFriction and wear tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: DISTILLED WATER. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180 and 300s. (stored in separate...
-
Wear in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). No lubrication (DRY). Specim. set K04
Open Research DataFriction and wear tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: DRY. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180 and 300s. (stored in separate folders).Specimen...
-
Wear in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - PARAFFIN OIL. Specim. set K09 - pre-run (10s)
Open Research DataFriction and wear tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: PARAFFIN OIL. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180 and 300s. (stored in separate...
-
Wear in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - PARAFFIN OIL. Specim. set K08
Open Research DataFriction and wear tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: PARAFFIN OIL. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180 and 300s. (stored in separate...
-
Wear in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - DISTILLED WATER. Specim. set K07
Open Research DataFriction and wear tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: DISTILLED WATER. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180 and 300s. (stored in separate...
-
Wear in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). No lubrication (DRY). Specim. set K05
Open Research DataFriction and wear tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: DRY. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180 and 300s. (stored in separate folders).Specimen...
-
Wear in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - DISTILLED WATER. Specim. set K02
Open Research DataFriction and wear tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: DISTILLED WATER. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180 and 300s. (stored in separate...
-
Wear in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). No lubrication (DRY). Specim. set K03
Open Research DataFriction and wear tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: DRY. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180 and 300s. (stored in separate folders).Specimen...
-
Combined environmental testing device for picosatellites
PublicationAs access to space conditions becomes more available, both technically and economically, scientists’ interest in launching finer and more sophisticated experiments grows. To be qualified for launch, such experiments need to be carefully tested prior to the event. The tests should represent actual launch conditions as closely and in a detailed manner. Typical tests for payload include: vibration tests, thermal and vacuum tests,...
-
Formation of gold anostructures detected by SEM microscope
Open Research DataGold nanostructures were prepared on silicon - Si(111) as a substrate. The substrates (1 × 1 cm2 of area) were cleaned with acetylacetone and then rinsed in ethanol. Thin Au films (with thicknesses in a range of 1.7–5.0 nm) were deposited using a table-top dc magnetron sputtering coater (EM SCD 500, Leica) under pure Ar plasma conditions (Argon, Air...
-
Geometria wykreślna I, 2019/20
e-Learning CoursesKurs „Geometria wykreślna I” łączy w sobie elementy kształcenia tradycyjnego z e-nauczaniem. Przeznaczony jest dla studentów kierunku Architektura, sem. 1, studia inżynierskie I stopnia. Tematyka dotyczy graficznej prezentacji obiektów 3D na płaszczyźnie, ich restytucji na podstawie rzutów oraz rozwiązywania prostych problemów przestrzennych. Treść nauczania obejmuje założenia metody rzutów prostokątnych na dwie rzutnie (metoda...
-
Influence of vision measurement system spatial configuration on measurement uncertainty, based on the example of electric traction application
PublicationTechnical diagnostics plays a significant role in ensuring operational reliability of electrified rail transport. The most critical point in the transmission of electric energy to vehicles is the sliding contact of the current collector with the traction network. For this reason, work is currently being carried on new measuring methods, whose appliance allows for more complete diagnostics of the contact line and current collectors,...
-
The experience of movement in the built form and space: A framework for movement evaluation in architecture
Publication“Movement in architecture” is an organized system of various types of movements stimulated by specific architectural elements. This research was conducted through a qualitative-analytical method and empirical and bibliographical research methods with the aim to categorize different types of movements based on the explorer and observer relationships with the built space and form. So far, most of the related studies have focused...
-
Reduction of vibrations of steel structure models with Polymeric Bearings - experimental study
PublicationEarthquake-induced ground motions are the most severe and unpredictable threats to the structures all around the world. Therefore, designing earthquake protective systems has become an extremely challenging problem in civil engineering. Base isolation is one of the most popular and widely adopted methods of protecting structures against earthquake forces. The present paper reports the results obtained from the shaking table experimental...
-
Effect of excitation intensity on slope stability assessed by a simplified approach
PublicationThe paper concerns the selection of a design accelerograms used for the slope stability assessment under earthquake excitation. The aim is to experimentally verify the Arias Intensity as an indicator of the excitation threat to the slope stability. A simple dynamic system consisting of a rigid block on a rigid inclined plane subjected to horizontal excitation is adopted as a slope model. Strong ground motions recorded during earthquakes...
-
Analysis of Roughness, the Material Removal Rate, and the Acoustic Emission Signal Obtained in Flat Grinding Processes
PublicationIn this work, the analysis of the acoustic emission (AE) signal in grinding processes is addressed. The proposed analysis method decomposes the acoustic signal into three frequency ranges. The total energy of each range is determined, as well as the highest frequency. Different grinding experiments were carried out, according to a full factorial design of experiments (DOE), in which feed speed, depth of cut, and transversal step...
-
JamesBot - an intelligent agent playing StarCraft II
PublicationThe most popular method for optimizing a certain strategy based on a reward is Reinforcement Learning (RL). Lately, a big challenge for this technique are computer games such as StarCraft II which is a real-time strategy game, created by Blizzard. The main idea of this game is to fight between agents and control objects on the battlefield in order to defeat the enemy. This work concerns creating an autonomous bot using reinforced...
-
Linear viscoelastic modelling of damage-involved structural pounding during earthquakes
PublicationDamage-involved structural pounding during earthquakes has been recently intensively studied using different impact force models. The results of the previous studies indicate that the linear viscoelastic model is relatively simple yet accurate in modelling pounding-involved behaviour of structures during earthquakes. The only shortcoming of the model is a negative value of the pounding force occurring just before separation, which...
-
Reliability assessment of an OVH HV power line truss transmission tower subjected to seismic loading
PublicationThe study focuses on the reliability of a transmission tower OS24 ON150 + 10, an element of an OVH HV power line, under seismic loading. In order to describe the seismic force, the real-life recording of the horizontal component of the El Centro earthquake was adopted. The amplitude and the period of this excitation are assumed random, their variation is described by Weibull distribution. The possible space state of the phenomenon...
-
Diagnostyka łożysk silnika indukcyjnego na podstawie prądu zasilającego przy użyciu sztucznych sieci neuronowych
PublicationW artykule zawarto wyniki badań dotyczące diagnostyki łożysk silnika indukcyjnego na podstawie pomiarów prądu zasilającego z wyko-rzystaniem sztucznych sieci neuronowych. Zaprezentowano wyniki uczenia sieci oraz rezultaty testów przeprowadzonych na danych spoza zbioru uczącego. Badania wykonane zostały na obiektach z celowo wprowadzonymi uszkodzeniami łożysk. Przedstawiona nowa koncepcja zakłada użycie zestawu sieci neuronowych...
-
Matematyka Stosowana. Grafika inzynierska - zastosowania, 2022/23
e-Learning CoursesKurs przeznaczony jest jako wsparcie dydaktyczne przedmiotu Matematyka stosowana na 3 semestrze studiów I stopnia kierunku Gospodarka przestrzenna. Celem kursu jest rozwinięcie umiejętności wykorzystywania wiedzy ścisłej w gospodarowaniu przestrzenią, a w szczególności poszerzenie wiedzy oraz rozwinięcie umiejętności dotyczących praktycznych aspektów kształtowania trójwymiarowej przestrzeni oraz metod sporządzania i odczytywania...
-
Data obtained by numerical simulation for X-ray focusing using a finite difference method
Open Research DataThe propagation of X-ray waves through an optical system consisting of many X-ray refractive lenses is considered. For solving the problem for an electromagnetic wave, a finite-difference method is applied.
-
PROBABILISTYCZNE ASPEKTY ZUŻYCIA SKOJARZEŃ CIERNYCH UKŁADÓW KORBOWO-TŁOKOWYCH NA PRZYKŁADZIE OKRĘTOWYCH SILNIKÓW SPALINOWYCH DWUSUWOWYCH NAPĘDU GŁÓWNEGO
PublicationW artykule przestawiono propozycję rozpatrywania zarówno obciążenia jak i zużywania ślizgowych skojarzeń ciernych (łożysk głównych i korbowych) układów korbowo-tłokowych silników spalinowych, zwłaszcza głównych, a także skojarzeń „tłok-tuleja” tych silników, jako procesów stochastycznych. Propozycję tę uzasadniono tym, że deterministyczne podejście do badania zarówno obciążenia jak i zużycia wspomnianych skojarzeń uniemożliwia...
-
Surface Dielectric Barrier Discharge Plasma Actuators
PublicationThis paper presents a part of the works conducted in the Plasmaero European project (task 1.1) on surface dielectric barrier discharge actuators applied to airflow control. The study is divided into several parts. In the first part, the goal is to enhance the electric wind produced by a typical single DBD actuator by optimization of the active electrode shape. For instance, the use of a thin wire instead of a plate air-exposed...
-
Centrally Pivoted Tilting Pad Thrust Bearing with Carbon-Based Coated Collar—Experimental Results of Low- and Medium-Speed Operation
PublicationExperimental results of the research on a tilting pad thrust bearing with symmetrical pad support in the conditions of high loads and low speeds are presented in the paper. As described in the literature review, experimental results of tilting pad bearings at low speed/high load regime and transient conditions are rare. Unusual material selection - steel pad against a DLC-type coating on the collar was utilized. Such material combination...
-
COMPARISON OF SYSTEM ON CHIP TECHNOLOGIES FOR SPACE APPLICATIONS
PublicationThe paper presents a review of technologies available for the implementation of digital and mixed signal systems, particularly the system on a chip (SoC) for space applications. The phenomena encountered in the space environment are briefly presented, together with the known solutions, regarding the design of complex electronic systems. The most important norms regarding single die integrated circuits designed for space are also...
-
The In-Depth Studies of Pulsed UV Laser-Modified TiO2 Nanotubes: The Influence of Geometry, Crystallinity, and Processing Parameters
PublicationThe laser processing of the titania nanotubes has been investigated in terms of morphology, structure, and optical properties of the obtained material. The length of the nanotubes and crystallinity, as well as the atmosphere of the laser treatment, were taken into account. The degree of changes of the initial geometry of nanotubes were checked by means of scanning electron microscopy, which visualizes both the surface and the cross-section....
-
Numerical evaluation of dynamic response of an experimentally tested base-isolated and fixed-base steel structure model
PublicationSeismic isolation is recognized as one of the most popular and effective methods of protecting structures during earthquake. The present paper is focused on the comparison be-tween the dynamic responses of buildings with fixed and isolated bases exposed to seismic exci-tations. The aim of the study is to investigate the effectiveness of a simplified base isolation numerical modelling technique using the linear springs. One-storey...
-
Modeling of the Two-Dimensional Flow Caused by Sea Conditions and Wind Stresses on the Example of Dead Vistula
PublicationThe article presents the results of two-dimensional modeling of flows caused by the sea conditions and wind stresses on the example of Dead Vistula. Based on the available bathymetric data, a numerical model of the river section was created, which was supplemented with data on the position of the water table depending on hydrometeorological conditions. To describe the flow field in steady conditions, a simplified model of two-dimensional...
-
Investigation on Damage-Involved Structural Response of Colliding Steel Structures during Ground Motions
PublicationEarthquakes are the most unpredictable damaging loads which can affect civil engineering structures. Due to insufficient separation distance between adjacent structures with different dynamic properties, structural collisions may occur during ground motions. Although the research on structural pounding has recently been much advanced, the studies have mainly been conducted for concrete structures. The aim of this paper is to show...
-
The complete list of two-dimensional number-conserving ternary cellular automata
Open Research DataThis dataset contains a complete list of all 1327 two-dimensional number-conserving cellular automata with the state set {0,1,2} (the so-called ternary cellular automata) based on adjacent cells only, i.e. with the von Neumann neighborhood. The detailed definitions and the method of enumerating are given in the paper:
-
Analiza wezbrania rzeki Kaczej w Gdyni po opadzie z 14 lipca 2016 roku
PublicationW połowie lipca 2016 r. w Trójmieście, zanotowano opad atmosferyczny o sumie przekraczającej 150 mm. Opadom deszczu od godzin popołudniowych dnia 14 lipca do godzin rannych 15 lipca towarzyszył okresami bardzo silny i gwałtowny wiatr początkowo z kierunku północno-wschodniego następnie z kierunku północno-zachodniego. Opisana sytuacja hydro-meteorologiczna spowodowała znaczne wezbrania w rzekach i potokach rejonu Zatoki Gdańskiej,...
-
Biologia ekosystemów laboratorium - nowy - 2023/24
e-Learning CoursesDane przedmiotu Nazwa kursu Biologia ekosystemów - wstęp do laboratorium Kierunek studiów Zielone Technologie Wydział Chemiczny Poziom kształcenia Studia I stopnia inżynierskie Forma studiów Stacjonarne Rok studiów 1 Semestr studiów 3 Start semestru21 1 październik 2023 Rok akademicki realizacji przedmiotu 2023/2024 Forma zajęć Stacjonarna Prowadzący i konsultacje Imię i nazwisko prowadzącego Beata Zalewska-Piątek...
-
Enhancement of lift and drag performances of a NACA0012 airfoil by multi-DBD plasma actuator with additional floating interelectrodes
PublicationIt is clear that the improvement of aircraft aerodynamic performances is currently and will continue to be a significant area of research for the aeronautical industry. The current study is focused on theenhancement of aerodynamic airfoil performances by using a multi-DBD plasma actuator mounted around the model leading-edge. Experiments have been conducted at the University of Orleans, in the 2 m x 2 m test section of a large...
-
Cutting model parameters from frame sawing of natural and impregnated Scots pine (Pinus sylvestris L.)
PublicationIn this paper, absolute and density normalized cutting model parameters of natural and impregnated Scots pine (Pinus sylvestris L.) are shown and a method for the calculation of their corresponding material properties in the principal material directions of wood is presented. The parameters were determined from measurements of cutting power on a sash gang saw, and are in detail the fracture toughness and the shear yield strength...