Search
Filters
total: 2871
displaying 1000 best results Help
Search results for: INDUSTRIAL GAS TURBINE
-
Control of the wind turbine generator
PublicationWind power system consists of two main parts: wind turbine and electrical generator. Wind turbine converts the energy of the flowing air into mechanical energy, next generator converts this energy into electrical energy that is sent to the power system. These two processes should be realized with maximum efficiency and the following requirements for the control system can be formulated: opti-mal wind power conversion, compensation...
-
New Procedures for Control of Industrial Effluents Treatment Processes
PublicationThis work presents the procedures for monitoring volatile organic compounds during treatment of industrial effluents. The investigation was carried out for a specific effluent—caustic effluent from bitumen production. The developed procedures enable more detailed control of the effectiveness of wastewater treatment than standard procedures. Caustic effluents from bitumen production have a complex physicochemical form and consist...
-
Advanced Turbine Cycles with Organic Media
PublicationOrganic Rankine Cycle (ORC) power plants have become very popular and have found their applications in systems with renewable sources of energy. So far their overall efficiencies are not very impressive and only for the upper temperature of about 300 °C do they exceed 20%. A drawback of these cycles is the limitation of the cycle upper temperature due to the heat exchanger technology and the materials used. However, it is possible...
-
Dynamic model of nuclear power plant turbine
PublicationThe paper presents the dynamic multivariable model of Nuclear Power Plant steam turbine. Nature of the processes occurring in a steam turbine causes a task of modeling it very difficult, especially when this model is intended to be used for on-line optimal process control (model based) over wide range of operating conditions caused by changing power demand. Particular property of developed model is that it enables calculations...
-
Possibilities of Increasing the Overall Efficiency of Gas-steam CHP Microplant
PublicationThe paper presents ways to increase the efficiency of a gas-steam micro power plant by modifying the cycle combination. The modification consists in partial release of the fluid downstream of the gas turbine and using it for ORC fluid overheating and evaporation. Advantages of this solution over the simplest gas and steam cycles’ combination are demonstrated.
-
A multistage turbine for a micro power plant
PublicationThis paper presents results of a design analysis of a multi-stage turbine for the cogeneration micro-power plant working in accordance with Organic Rankine Cycle (ORC). The heat power of the plant is assumed equal to 20 kW and the corresponding available electric output is estimated to be of about 3 kW. Different variants of the radial and axial-flow turbines have been considered, while the detailed results of the calculations...
-
INFLUENCE OF INLET GEOMETRY ON THE EFFICIENCY OF 1MW STEAM TURBINE
PublicationThe process of the design of the 1MW steam turbine includes designing the stator and rotor blades, the steam turbine inlet and exit, the casing and the rotor. A turbine that operates at rotation speeds other than 3000 rpm requires a gear box and generator with complex electronic software. This paper analyses the efficiency of eight turbine variants, including seven inlet geometries and three stages of stator as well as an eight...
-
Proposition of the steam turbine governor structure modification
PublicationThere is considered the steam turbine governor operation during defense and restoration of the power system. It points out weaknesses of currently used governor structures. The new controller is proposed, that takes advantages of those curently used. The new controller allows for more effective control of the turbine in emergency situations, at frequencies much different from the nominal value.
-
Operation evaluation method for marine turbine combustion engines in terms of energetics
PublicationAn evaluation proposal (quantitative determination) of an y combustion turbine engine operation has been presented , wherein the impact energy occurs at a given time due to Energy conversion. The fact has been taken into account that in this type of internal combustion engines the energy conversion occurs first in the combustion chambers and in the spaces between the blade of the turbine engine. It was assumed that in the combustion...
-
Approaching Secure Industrial Control Systems
PublicationThis study presents a systematic approach to secure industrial control systems based on establishing a business case followed by the development of a security programme. To support these two fundamental activities the authors propose a new method for security cost estimation and a security assessment scheme. In this study they explain the cost evaluation technique and illustrate with a case study concerning the assessment of the...
-
Complex multidisciplinary optimization of turbine blading systems
PublicationThe paper describes the methods and results of direct optimization of turbine blading systems using a software package Opti_turb. The final shape of the blading is obtained from minimizing the objective function, which is the total energy loss of the stage, including the leaving energy. The current values of the objective function are found from 3D RANS computations (from a code FlowER) of geometries changed during the process...
-
Domestic ORC micro-CHP combined with a commercial gas boiler
PublicationThe chapter presents the results of experimental studies conducted during the launch of the first in Poland demonstration prototype of the micro ORC coupled to a domestic gas boiler. The accomplished studies indicated the possibility for the ORC module to work with such boiler (autonomous source of heat) with a prototype single-stage axial micro turbine as the expansion machine. Confirmation of that fact has been delineated in...
-
Negative carbon dioxide gas power plant integrated with gasification of sewage sludge
PublicationOne of the primary objectives of the negative carbon dioxide gas power plant (nCO2PP) is to develop an innovative technology confirming the possibility of the use of sewage sludge to produce electricity while having a positive impact on the environment. In this paper, a mathematical model is presented to estimate thermodynamic parameters of the system in relation to the gasification process and changes in such parameters in the...
-
Pressure pulsations in turbine blade seal clearance
PublicationThe paper presents the results of numerical and experimental investigations into pressure forces generated in a turbine labyrinth seal. The experiments were performed on a single-stage air model turbine of the impulse type, while the numerical results were obtained by means of CFD Fluent Code. The performed experimental research and numerical calculations prove that in a shroud clearance the pressure pulsates and the effects of...
-
Neural Modelling of Steam Turbine Control Stage
PublicationThe paper describes possibility of steam turbine control stage neural model creation. It is of great importance because wider application of green energy causes severe conditions for control of energy generation systems operation Results of chosen steam turbine of 200 MW power measurements are applied as an example showing way of neural model creation. They serve as training and testing data of such neural model. Relatively simple...
-
The ranks of Japanese industrial sectors: 2005-2011
PublicationThe purpose of the current study is to expand the previous study which analyzes the industrial sectors ranks of specific countries. More specifically, the study aims to conduct a comparison in terms of the ranks of Japanese industrial sectors on the specific analysis period. The analysis period of the study is 2005-2011. Using the previous study as a reference, the study employs the Input-Output (IO) approach as an analysis instrument....
-
The ranks of Japanese industrial sectors: 2005-2011
PublicationThe purpose of the current study is to expand the previous study which analyzes the industrial sectors ranks of specific countries. More specifically, the study aims to conduct a comparison in terms of the ranks of Japanese industrial sectors on the specific analysis period. The analysis period of the study is 2005-2011. Using the previous study as a reference, the study employs the Input-Output (IO) approach as an analysis instrument....
-
Polyether-block-amide PEBA membranes for gas separation and pervaporation; current design and applications
PublicationPolyether-block-amide (PEBA) membranes have attracted considerable attention for their exceptional efficacy in gas separation and pervaporation processes. This comprehensive review delves into the precise definition, distinguishing characteristics, and diverse applications of PEBA membranes over the past five years. A primary research objective focuses on enhancing gas separation efficiency, primarily through augmenting membrane...
-
The ranks of Indonesian and Japanese industrial sectors: A further study
PublicationThe purpose of the current study is to extend the previous study which analyzes the industrial sectors ranks of specific countries. More specifically, the study aims to conduct a further analysis regarding the ranks by using the new data as well as new analysis periods. The study focuses on the cases of Indonesia and Japan. In this study, the analysis period of the Indonesian case is 2010 while for the case of Japan is 2011. Using...
-
An analysis of the characteristics of Indonesian industrial sectors: 2005-2010
PublicationThe purpose of the current study is to analyze the characteristics of Indonesian industrial sectors from 2005 through 2010. The study employs the analysis instruments from the Input-Output (IO) analysis, namely the indices of the power of dispersion, and the sensitivity of dispersion. For 2005 and 2010, the study focuses on nine and seventeen industries, respectively. The results show that industry 3, manufacturing, placed the...
-
An analysis of the characteristics of Indonesian industrial sectors: 2005-2010
PublicationThe purpose of the current study is to analyze the characteristics of Indonesian industrial sectors from 2005 through 2010. The study employs the analysis instruments from the Input-Output (IO) analysis, namely the indices of the power of dispersion, and the sensitivity of dispersion. For 2005 and 2010, the study focuses on nine and seventeen industries, respectively. The results show that industry 3, manufacturing, placed the...
-
The ranks of Indonesian and Japanese industrial sectors: A further study
PublicationThe purpose of the current study is to extend the previous study which analyzes the industrial sectors ranks of specific countries. More specifically, the study aims to conduct a further analysis regarding the ranks by using the new data as well as new analysis periods. The study focuses on the cases of Indonesia and Japan. In this study, the analysis period of the Indonesian case is 2010 while for the case of Japan is 2011. Using...
-
Steam and Gas Turbines Constuction_ seminar/project
e-Learning Courses -
Determination of Failure Causes of a Steam Turbine Casing
PublicationThe paper presents results of research and failure analysis undertaken to determine failure causes of a steam turbine casing. After 130,000 hours of service the crack in a outer shell of the turbine casing was found. The inner shell of the casing was made of cast steel grade G21CrMoV5-7, and the outer shell of grade G20CrMo4-5. Following research were performed in order to determine causes of the casing failure: chemical analysis;...
-
Improving operating efficiency of a gas turboset via cooperation with an absorption refrigerating machine
PublicationThe analysis of increase of ambient air temperature entering the compressor on reduction in power output from the turbine and increase fuel use was conduced. For medium size gas turbine operates in winter and summer conditions elementary power and economical values was calculated. Conditions of the determination of turbine inlet air cooling solution (using thermal storage for reduce equipment size) are presented
-
On a Method of Efficiency Increasing in Kaplan Turbine
PublicationThis paper presents a method of increasing efficiency in Kaplan-type turbine. The method is based on blade profile optimisation together with modelling the interaction between rotor and stator blades. Loss coefficient was chosen as the optimisation criterion, which is related directly to efficiency. Global optimum was found by means of Genetic Algorithms, and Artificial Neural Networks were utilised for approximations to reduce...
-
Gas turbines – technological development and potential use in CAES systems
PublicationThis article briefly describes Compressed Air Energy Storage (CAES), focusing on the technological development of one of the key elements of such systems – the gas turbines. It presents the basic parameters and features of gas turbines, as well as turbine classes with example models. Main tendencies in the structural and technological development are discussed. Changes and trends on electric energy markets are becoming more and...
-
Efficiency of gas mixtures detection by resistive gas sensors
PublicationResistive gas sensors are very popular and are commonly used to detect various gases and their mixtures. Theeir main disadvantage is very limited selectivity. Practical use of gas sensors in environenmental applications requires determination of concentration of a few mixed gases at the same time. We would like to present recent results of gas detection improvement by utilizing a single gas sensor and additional measurements to...
-
EFFICIENCY OF GAS MIXTURES DETECTION BY RESISTIVE GAS SENSORS
PublicationResistive gas sensors are very popular and are commonly used to detect various gases and their mixtures. Their main disadvantage is very limited selectivity. Practical use of gas sensors in environmental applications (e.g., in sewage systems to protect workers, in air conditioning systems to monitor atmosphere quality) requires determination of concentration of a few mixed gases at the same time. We would like to present recent...
-
Modelling of Nuclear Power Plant Steam Turbine
PublicationThe paper describes the approach to a Nuclear Power Plant steam turbine modelling which would enable on-line optimal process control (model based) and diagnosis over wide range of operating conditions caused by changing power demand. Presented model is static, multivariable and nonlinear. Such model enables analyzing the heat cogeneration aspects. Developed model is validated and verified by using archive data gained from researches...
-
Modelling of Nuclear Power Plant Steam Turbine
PublicationThe paper describes the approach to a Nuclear Power Plant steam turbine modelling which would enable on-line optimal process control (model based) and diagnosis over wide range of operating conditions caused by changing power demand. Presented model is static, multivariable and nonlinear. Such model enables analyzing the heat cogeneration aspects. Developed model is validated and verified by using archive data gained from researches...
-
Selectivity of amperometric gas sensors in multicomponent gas mixtures
PublicationIn recent years smog and poor air quality became a growing environmental problem. There is a need to continuously monitor the quality of air. The lack of selectivity is one of the most important problems limiting the use of gas sensors for this purpose. In this study, a selectivity of the six amperometric gas sensors is being investigated. Calibration of sensors has been performed in order to find a correlation between concentration...
-
Gas sampling system for matrix of semiconductor gas sensors
PublicationSemiconductor gas sensors are popular commercial sensors applied in numerous gas detection systems. They are reliable, small, rugged and inexpensive. However, there are a few problem limiting the wider use of such sensors. Semiconductor gas sensor usually exhibits a low selectivity, low repeatability, drift of response, strong temperature and moisture influence on sensor properties. Sample flow rate is one of the parameters that...
-
Suitableness of SLM Manufactured Turbine Blade for Aerodynamical Tests
PublicationsettingsOrder Article Reprints Open AccessArticle Suitableness of SLM Manufactured Turbine Blade for Aerodynamical Tests by Janusz Telega 1,*ORCID,Piotr Kaczynski 1ORCID,Małgorzata A. Śmiałek 2ORCID,Piotr Pawlowski 3ORCID andRyszard Szwaba 1ORCID 1 Institute of Fluid Flow Machinery Polish Academy of Sciences (IMP PAN), Fiszera 14, 80-231 Gdansk, Poland 2 Faculty of Mechanical Engineering and Ship Technology, Institute of Naval...
-
The thermal effort during marine steam turbine flooding with water
PublicationThe work discussed an extreme case of cooling a steam turbine. The ship's steam turbine was used as an example. In marine transport units with low-speed engines dominate, however, there are also units with steam turbines. An example of analysed marine steam turbine is shown in Fig. 1. When considering the issue of cooling steam turbines, it is necessary to estimate the extreme conditions that may occur during operation of the turbine....
-
ANALYSIS OF THE PROJECT OF INNOVATIVE FLOATING TURBINE
PublicationThe design of a floating, innovative device for river water aeration and conversion of mechanical energy to electrical energy required the analysis of a number of geometrical and dynamic features. Such an analysis may be carried out on the basis of existing methods of numerical fluid mechanics. Models of pressures, forces and torques characteristic for the conversion of watercourse energy were developed for two basic concepts of...
-
Inorganic membrane: a game changer for gas separation and purification
PublicationThis review explores the advancements and remaining challenges in inorganic membrane science, particularly focusing on their potential for industrial applications. It delves into the fundamental principles of inorganic membrane design, fabrication, and characterization techniques. The review also critically analyzes key challenges faced by inorganic membranes, such as physical aging, plasticization, defective formation, and fouling....
-
Simplified, multiregional fuzzy model of a nuclear power plant steam turbine
PublicationPower systems, including steam turbines and synchronous generators, are complex nonlinear systems with parameters varying over time. The paper presents the developed simplified, multiregional fuzzy model of the steam turbine of a nuclear power plant turbine generator set and compares the results with a full nonlinear model and commonly used linear input-output model of a steam turbine. The proposed model consist of series of linear...
-
SELECTED COMBINED POWER SYSTEMS CONSISTED OF SELFIGNITION ENGINE AND STEAM TURBINE
PublicationThis paper presents optimization of selected combined diesel engine-steam turbine systems. Two systems: the system combined with waste heat one-pressure boiler only and its version containing additionally low-pressure boiler proper feeding degasifier and the system of two-pressure cycle, were taken into considerations. Their surplus values of power output and efficiency associated with utilization of waste heat contained in piston...
-
Design analysis of Tesla micro-turbine operating on a low-boiling medium
PublicationThis paper presents results of the design analysis of a Tesla bladeless turbine intended for a co-generating micro-power plantof heat capacity 20 kW, which operates in an organic Rankine cycle on a low-boiling medium. Numerical calculations of flowin several Tesla turbine models were performed for a range of design parameters. Results of investigations exhibit interestingfeatures in the distribution of flow parameters within the...
-
Gas selectivity enhancement by sampling-and-hold method in resistive gas sensors
PublicationCommercial resistive gas sensors exhibit various sensitivity to numerous gases when working at different elevated temperatures. That effect is due to a change in velocity of adsorption and desorption processes which can be modulated by temperature. Thus, to reach better selectivity of gas detection, we propose to apply a known method (called the sampling-and-hold method) of cooling down the gas sensor in the presence of the investigated...
-
On the modelling of aerodynamic force coefficients for over-shroud seals of turbine stages
PublicationThis paper presents experimental investigations which made it possible to determine dynamic coefficients of labyrinth over-shroud seal of a model air turbine. The coefficients associate pressure forces with turbine rotor displacement, velocity and acceleration respective to turbine casing (linear model) and play important role in analyzing turbine-set dynamics. The obtained results indicated that involving serious errors can be...
-
Immobilized biocatalysts - useful tool for industrial processes
PublicationThe main goal of biomaterials immobilization is the industrial re-use of them for many reaction cycles. However, application of this technolgoy for full commercialization requires more experiments in this field. In this study thermostable beta-galactosidases from Ptrococcus woesei and Meiothermus ruber were taken as model proteins immobilized in alginate gel.
-
The use of constructed wetlands for the treatment of industrial wastewater
PublicationConstructed wetlands are characterized by specific conditions enabling simultaneous various physical and biochemical processes. This is the result of specific environment for the growth of microorganisms and hydro-phytes (aquatic and semiaquatic plants) which are capable of living in aerobic, anaerobic and facultative anaerobic conditions. Their interaction contributes to the intensification of oxidation and reduction responsible...
-
The Method of reduction of aerodynamic forces generated in turbine blade seals
PublicationThe distibution of pressure in the seal gaps does not only affect the so called '' leakage losses'' and the turbine stage overall efficiency but also plays an important role in the generation of aerodynamic forces which may cause self-excited rotor vibrations. The paper describes a chamber seal applied for the reduction of the aerodynamic forces created in shroud seals. This kind of turbine seal was patented and tested.
-
Explanation of Reduction of Pressure Forces in Turbine Chamber Seals
PublicationThe paper describes a chamber seal reducing the aerodynamic forces created in shroud seals. Asymmetrical pressure distribution (due to rotor-stator eccentricity) in the blade tip clearance leads to the creation of pressure forces acting on the blade shroud. By increasing the volume above the shroud, the pressure distribution becomes more uniform on the whole shroud circumference and the effect of rotor eccentricity is reduced....
-
Explanation of Reduction of Pressure Forces in Turbine Chamber Seals
PublicationThe paper describes a chamber seal reducing the aerodynamic forces created in shroud seals. Asymmetrical pressure distribution (due to rotor-stator eccentricity) in the blade tip clearance leads to the creation of pressure forces acting on the blade shroud. By increasing the volume above the shroud, the pressure distribution becomes more uniform on the whole shroud circumference and the effect of rotor eccentricity is reduced....
-
The ranks of Indonesian and Japanese industrial sectors
PublicationThe purpose of this study is to determine the ranks of Indonesian and Japanese industrial sectors from the economic point of view. The analysis period of this study is 2005. This study employs one of the well-known analysis tools in the economic topic, the Input-Output (IO) analysis. More specifically, this study uses the analysis methods in the IO analysis, backward and forward linkages, in order to achieve the purpose. The results...
-
The ranks of Indonesian and Japanese industrial sectors
PublicationThe purpose of this study is to determine the ranks of Indonesian and Japanese industrial sectors from the economic point of view. The analysis period of this study is 2005. This study employs one of the well-known analysis tools in the economic topic, the Input-Output (IO) analysis. More specifically, this study uses the analysis methods in the IO analysis, backward and forward linkages, in order to achieve the purpose. The results...
-
An Innovative Floating System with a Savonius Rotor as a Horizontal-Axis Wind Turbine
PublicationIn this project, an innovative wind turbine was designed for a floating plant. A large Savonius rotor was replaced with a double-rotor wind turbine implemented as a horizontal-axis turbine. This double rotor was positioned on the tip of a thrust plate and fixed to the deck of a catamaran. Simple 2D numerical simulations were performed to confirm the effectiveness of the concept. An analysis of the floating system configuration...