Filters
total: 2731
filtered: 2198
displaying 1000 best results Help
Search results for: MELT-BLENDING
-
Fracture Areas Quantitative Investigating of Bending-Torsion Fatigued Low-Alloy High-Strength Steel
PublicationIn this study, the impact of pseudo-random non-proportional bending-torsion fatigue loadings proportion on the fatigue life and the fracture surface topography was analyzed. Investigation was carried out for 24 specimens made of S355J2 steel with 11 different ratios of maximum stresses λ. For these cases, after the fatigue tests, the surface topography measurements were carried out using an optical profilometer, using the focus...
-
Impact performance of novel multi-layered prepacked aggregate fibrous composites under compression and bending
PublicationMulti-layered Prepacked aggregate fibrous composite (MLPAFC) is a new type of concrete, which is prepared in two subsequent stages of aggregate-fibre skeleton prepacking and cementitious grouting. In this study, ten MLPAFC mixtures were prepared in three subsequent layers incorporating different contents of four different types of steel fibres. Long and short hooked-end and crimped steel fibers were adopted with 3.0 and 1.5% dosages...
-
A general isogeometric finite element formulation for rotation‐free shells with in‐plane bending of embedded fibers
PublicationThis article presents a general, nonlinear isogeometric finite element formulation for rotation-free shells with embedded fibers that captures anisotropy in stretching, shearing, twisting, and bending - both in-plane and out-of-plane. These capabilities allow for the simulation of large sheets of heterogeneous and fibrous materials either with or without matrix, such as textiles, composites, and pantographic structures. The work...
-
Size effect in concrete beams under bending – influence of the boundary layer and the numerical description of cracks
PublicationIn the paper the size effect phenomenon in concrete is analysed. The results of numerical simulations of using FEM on geometrically similar un-notched and notched concrete beams under bending are presented. Concrete beams of four different sizes and five different notch heights under three-point bending test were simulated. In total 18 beams were analysed. Two approaches were used to describe cracks in concrete. First, eXtended...
-
Three-point bending test of sandwich beams supporting the GFRP footbridge design process - validation
PublicationSome selected aspects concerning material and construction design issues for pedestrian footbridge made of GFRP composite materials are elaborated in this paper. The analysis is focused on validation tests, which are particularly important because of the advanced technology and materials that are used for this innovative bridge. The considered footbridge is a sandwich-type shell structure comprising of PET foam core and outer skins...
-
Bending Moment Control and Weight Optimization in Space Structures by Adding Extra Members in the Optimal Locations
PublicationThis paper investigates the reduction of bending moment in critical members by adding some extra members in the optimum location. Instead of enlarging the size of members to resist the moment, eight additional members are added in the optimum location to reduce the bending moment in the critical members. The total weight of the proposed structure with extra members is less than that of the original structure that resists the induced...
-
Two - scale model for concrete beams subjected to three point bending - numerical analyses and experiments
PublicationArtykuł omawia dwu-skalowe podejście do betonu przy wykorzystaniu połączonych modeli. Metodę elementów skończonych zastosowano na poziomie makro. Na poziomie mikro zastosowano metodę elementów dyskretnych. Macierz sztywności wyznaczono na podstawie tensora naprężeń wyznaczonego w skali mikro. Wyniki numeryczne dw-skalowe porównano z wynikami dyskretnymi dla całego obszaru.
-
Experimental Investigations of Fracture Process Using DIC in Plain and Reinforced Concrete Beams under Bending
PublicationThe fracture behaviour of concrete and reinforced concrete beams under quasi-static three-point bending was comprehensively investigated with experiments at laboratory scale. The eight various concrete mixes were tested. The influence of the shape, volume and size of aggregate particles and reinforcement on concrete fracture under bending was studied. Displacements on the surface of concrete beams were measured by means of the...
-
The effect of windthrow and its management on breeding bird communities in a managed forest
Publication -
Forest clear-cuts as additional habitat for breeding farmland birds in crisis
Publication -
ARCHITECTURE IN BRANDING AND OVERBRANDING PROCESS. HOW GLOBALIZATION INFLUENCED ARCHITECTURE QUALITY.
PublicationGlobalization is unification. In the field of architecture and in the social structure alike, the globalization leads to a blending of economies and cultures that produces uniformly branded public space as a response to universal assumptions of integration and correlation. While branding consists in creating a recognizable and outstanding image a strong contradiction exists between both of these approaches. As a result, regional...
-
Selfie and Personal Branding Phenomena in the Context of the Network Economy. A Literature Review
PublicationSelf-taken pictures called “selfies” shared in social media have become a worldwide phenomenon. This is due to the increased need of human being to share to other people their daily lives and to build their own personal brand in the networked world. Despite that, the subject of personal branding has not been sufficiently discussed in academic marketing literature over the past decade. The objective of the study is to present the...
-
Method for introducing liquid modifiers into melt-blown nonwovens during their production Metoda wprowadzania modyfikatorów w postaci roztworów do włóknin pneumotermicznych podczas procesu ich wytwarzania
Publication -
Band misplacement: a rare complication of laparoscopic adjustable gastric banding
Publication -
The First Report on Hybrid NOTES Adjustable Gastric Banding in Human
Publication -
Carotenoid binding to proteins: Modeling pigment transport to lipid membranes
Publication -
Optimising DNA binding to carbon nanotubes by non-covalent methods
Publication -
Copper binding by the cystatin C fragment. The role of histidine residues
Publication -
Bonding of doxorubicin to nanosilica and human serum albumin in various media
Publication -
Obtaining ionic forces by the total-energy tight-binding method
PublicationZastosowanie metody ciasnego wiązania w sformułowaniu nieortogonalnym do obliczania sił atomowych w symulacji metodą dynamiki molekularnej pozwala na stworzenie modelu charakteryzującego się lepszą przenośnością, w porównaniu z potencjałami empirycznymi, którymi posługuje się tradycyjna dynamika molekularna. W niniejszej pracy przedstawiono szczegółowo sposób obliczenia pochodnych elementów macierzy Hamiltona i macierzy nakładania...
-
Syntheses and DNA binding of new cationic porphyrin–tetrapeptide conjugates
Publication -
Binding of new cationic porphyrin–tetrapeptide conjugates to nucleoprotein complexes
Publication -
NMR and MD Analysis of the Bonding Interaction of Vancomycin with Muramyl Pentapeptide
Publication -
Binding free energy of selected anticancer compounds to DNA - theoreticalcalculations
PublicationPraca dotyczy swobodnej energii wiązania z DNA trzech związków o działaniu przeciwnowotworowym (mitoksantronu i dwóch pochodnych pirymidoakrydyny). Obliczenia wykorzystywały metody Poissona-Boltzmanna (udział elektrostatyczny) i metody SASA (udział nieelektrostatyczny). W wyniku badań zaproponowano struktury kompleksów jakie tworzą badane ligandy z DNA.
-
A new approach to cross-bonding in medium voltage cable lines
PublicationThe medium voltage underground cable sheaths are usually bonded and earthed in every substation on the cable route. This results in additional power losses in the sheaths. The paper presents an idea of reducing power losses caused by sheaths cross-bonding. The idea of sheaths cross-connecting only in selected MV/LV substations is given instead of a typical solution, where sheaths cross-bonding requires installing additional joints...
-
Metals and metal-binding ligands in wine: Analytical challenges in identification.
PublicationBackground Due to important role of metals in the vinification process as well as their impact on the human health, their content in this alcoholic beverage has been extensively studied by many researchers. It is already known that speciation of metals determines their toxicity and bioavailability as well as influences their activity. Understanding the chemistry and knowing the structures of metal complexes could have relevant...
-
Cross-Bonding of MV Cable Lines for Energy Losses Decrease
PublicationCurrently, almost all medium voltage cable lines (MV) operate with the return wires earthed at both ends of the cable. Such a way of operation causes that during normal states of operation as well as during disturbances, e.g. short-circuits, in the return wires induce currents whose values mainly depend on the currents flowing in the phase wires. These currents in normal operating states are a source of additional energy losses...
-
Positron binding to alkali-metal hydrides: The role of molecular vibrations
PublicationThe bound vibrational levels for J=0 have been computed for the series of alkali-metal hydride molecules from LiH to RbH, including NaH and KH. For all four molecules the corresponding potential-energy curves have been obtained for each isolated species and for its positron-bound complex (e+XH). It is found that the calculated positron affinity values strongly depend on the molecular vibrational state for which they are obtained...
-
Security of export transactions in the offer of leading banks on the Polish market
PublicationThe following article presents the so-called conditioned payment methods, i.e. instruments for securing export transactions, such as letter of credit, documentary collection, bank guarantees, factoring and forfaiting. The characteristics of each particular method are presented as well as the transactions using them are described. In the following paper, the author included also the leading Polish banks, which offer the above- mentioned...
-
Effect of interlayer bonding quality of asphalt layers on pavement performance
PublicationThe quality of interlayer bonding at the interfaces between the asphalt layers in flexible pavements affects the overall pavement performance. Lack or partial lack of interlayer bonding between asphalt layers can cause pavement's premature failures such as rutting, slippage of the wearing course, cracking or simply a reduction in the calculated fatigue life of the pavement structure. This paper shows the case studies of investigation...
-
The Influence of Binding Agents on Stiffness of Mineral-cement-emulsion Mixtures
PublicationThis paper attempts to determine the behavior of mineral-cement-emulsion mixture (MCE) under load, whether is it similar to asphalt mixtures (viscoelastic behavior) or to cement treated materials (elastic behavior). To answer this question nine mineral- cement-emulsion mixtures with different combinations of cement and emulsion content were tested in laboratory using Simple Performance Test (SPT). For each mixture stiffness moduli...
-
Meat products Brassica exploiting anticarcinogenic potential of cabbage phytochemicals: Polish path to bio-inspired foods
PublicationBadania populacyjne ostatnich dwóch dziesięcioleci wskazują na sposób odżywiania jako jeden z głównych czynników zagrożenia chorobami cywilizacyjnymi, z nowotworami włącznie. W przypadku chorób nowotworowych głównym elementem diety sprzyjającej kancerogenezie jest czerwone mięso. Ze względu na wartość odżywczą i powszechność spożycia produktów mięsnych, poprawienie ich wartości żywieniowej staje się problemem o istotnym znaczeniu...
-
Potential of bacteriocins from lab to improve microbial quality of dry-cured and fermented meat products [pdf]
Publication -
Quantitative and Qualitative Composition of Bacterial Communities of Malting Barley Grain and Malt during Long-Term Storage
Publication -
The influence of moderate pressure and subzero temperature on the shelf life of minced cod, salmon, pork and beef meat
PublicationThe effect of moderate pressure at subzero temperature on natural microflora of minced cod, salmony, pork and beef meat was studied. Pressure of 193 MPa at –20 °C caused reduction of total bacterial count in pork and beef meat by 1.1 and 0.6 log cycles, respectively, and by about 1.5 log cycles in fish meat. Under these conditions the psychrophilic and psychrotophic bacteria were below the detection limit (<10CFU/g of sample) in...
-
The Staged Combustion of Meat-and-Bone Meal:The Characteristics of Conversion Sub-processes and Large-Scale Process Outputs
Publicationt Organic waste has been playing an increasingly important role in the energy market as those that may support the economies in pursuing towards decarbonization by increasing the share of renewables in the overall energy balance. In this group of alternative fuels, meat-and-bone meals being a post-production waste of the steadily developing meat industry, constitute a considerable proportion. Though they are rich in minerals, their...
-
Changes in enzymatic activity of fish and slaughter animals meat after high pressure treatment at subzero temperatures
PublicationThe aim of this study was to determine changes in the activity of proteolytic enzymes and transglutaminase of fish and mammal meat after pressurization at subzero temperatures. The activity was measured at the optimal pHs determined for enzymes from particular types of tested meat. It was found that increasing the pressure in the range of 60–193 MPa, did not change significantly the activity of acidic proteases of cod flesh, while...
-
Energy-Saving Mechatronic System for Fatigue Tests of Materials under Variable-Amplitude Proportional Bending and Torsion
Publication -
Energy-based fatigue failure characteristics of materials under random bending loading in elastic-plastic range
Publication -
Correlation between Fractal Dimension and Areal Surface Parameters for Fracture Analysis after Bending-Torsion Fatigue
PublicationThis paper investigates the fracture surface topography of two steel and aluminum alloys subject to bending-torsion fatigue loadings, as well as their susceptibility to fatigue performance and failure mechanisms. Using fracture surface topography data analysis, elements with different geometries were elaborated. A correlation between the fractal dimension, other selected parameters of surface topography such as areal Sx, and...
-
The impact of surface slope and calculation resolution on the fractal dimension for fractures of steels after bending-torsion fatigue
PublicationThe article presents the results of the fractal dimension measurements on the fatigue fracture surfaces of 10HNAP and S355J2 steels specimens after combined bending-torsion fatigue. For smooth and ring-notched specimens, three loading conditions were analyzed: (1) bending; (2) bending-torsion; and (3) torsion fatigue. Post-failure surface topography measurements were carried out on the entire fracture surfaces using an optical...
-
Bending and buckling formulation of graphene sheets based on nonlocal simple first-order shear deformation theory
PublicationThis paper presents a formulation based on simple first-order shear deformation theory (S-FSDT) for large deflection and buckling of orthotropic single-layered graphene sheets (SLGSs). The S-FSDT has many advantages compared to the classical plate theory (CPT) and conventional FSDT such as needless of shear correction factor, containing less number of unknowns than the existing FSDT and strong similarities with the CPT. Governing...
-
Textile reinforced concrete members subjected to tension, bending, and in-plane loads: Experimental study and numerical analyses
PublicationTextile reinforced concrete has raised increasing research interest during the last years, mainly due to its potential to be used for freeform shell structures involving complex load situations. Yet, most experimental work has focused on test setups with primarily uniaxial loading. In the current work, such setups are complemented with a novel test setup of deep beams, including in-plane bending and shear. Further, nonlinear finite...
-
Topography measurement methods evaluation for entire bending-fatigued fracture surfaces of specimens obtained by explosive welding
PublicationIn this paper, the methods of compensation of differences in the results of entire bending-fatigued fracture surface topographies were presented. The roughness evaluation was performed with a focus variation microscope and confocal surface topography measurement techniques. The differences in the ISO 25178 roughness parameters were investigated and procedures for their compensation were studied. It was found that various types...
-
NON-LOCAL VOLUMETRIC APPROACH TO ANALYSIS DEFECT'S SHAPE INFLUENCE ON SPECIMENS DURABILITY SUBJECTED TO BENDING AND TORSION
PublicationThe influence of defect features on fatigue behaviour is a complex trivial issue. Although the important advances over the last decades, the dialectical relationship between the defect orientation and durability is not clearly understood. The paper aims at studying the influence of the orientation of elliptical defects on the durability of samples made of C45 steel. Three types of samples with elliptical defects were subjected...
-
A new anisotropic bending model for nonlinear shells: Comparison with existing models and isogeometric finite element implementation
PublicationA new nonlinear hyperelastic bending model for shells formulated directly in surface form is presented, and compared to four existing prominent bending models. Through an essential set of elementary nonlinear bending test cases, the membrane and bending stresses of each model are examined analytically. Only the proposed bending model passes all the test cases, while the other bending models either fail or only pass the test cases for...
-
Calculations of fracture process zones on meso-scale in notched concrete beams subjected to three-point bending.
PublicationW artykule przedstawiono wyniki numeryczne MES modelowanie belek betonowych z nacięciem na poziomie skali mezo. Beton został opisany na poziomie skali mezo jako stochastyczny materiał 3-składnikowy złożony z kruszywa, zaczynu cementowego oraz stref kontaktu. Obliczenia wykonano przy wykorzystaniu modelu degradacji sztywności z nielokalnym osłabieniem. Zbadano wpływ stochastycznego rozkładu kruszywa, średnicy, kształtu oraz zagęszczenia...
-
Parametric FE studies on a coupled energetic-statistical size effect in plain concrete beams under bending
PublicationW artykule omówiono wyniki połączonego deterministyczno-statystycznego efektu skali w betonowych belkach podczas zginania. Obliczenia wykonano stosując MES w zakresie sprężysto-plastyczności z nielokalnym osłabieniem. Obliczenia wykonano dla różnych długości korelacji i współczynnika zmienności.
-
Finite element analysis on failure of reinforced concrete corner in sewage tank under opening bending moment
PublicationW artykule omówiono mechanizm uszkodzenia żelbetowego zbiornika ściekowego w narożniku ściany, który uległ uszkodzeniu podczas próby wypełnienia na skutek nadmiernych przemieszczeń poziomych ścian pod wpływem otwierającego momentu zginającego. Aby wyjaśnić przyczyny awarii, przeprowadzono kompleksowe obliczenia metodą elementów skończonych (MES) żelbetowego zbiornika w warunkach odkształcenia płaskiego. Beton zamodelowano za pomocą...
-
Investigations on fracture in reinforced concrete beams in 3-point bending using continuous micro-CT scanning
PublicationThis study explores a fracture process in rectangular reinforced concrete (RC) beams subjected to quasi-static three-point bending. RC beams were short and long with included longitudinal reinforcement in the form of a steel or basalt bar. The ratio of the shear span to the effective depth was 1.5 and 0.75. The focus was on the load–deflection diagram and crack formation. Three-dimensional (3D) analyses of the size and distribution...