Filters
total: 1756
filtered: 1269
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: TURBINA WODNA
-
Stopień z upustem - analiza stacjonarna turbiny 13K215
PublicationW pracy przedstawiono analizę przepływu w obszarze stopnia turbiny parowej z upustem 13K215 przed modernizacją. Zaproponowano model umożliwiający taką analizę. W wyniku analizy uzyskano dystrybucje ciśnienia w kierunku obwodowym, co pozwala na określenie sił działających na łopatki wirnikowe, pracujacych w obszarze nierównomierności generowanych przez upust.
-
The Application of Fluidic Sealing in Shrouded Gas Turbine Blades
PublicationThis paper presents a study conducted on a new gas turbine designed to limit leakage in the labyrinth seal. The slots in the fin are used to generate a bypass flow, which obstructs the flow in the gap above the fin. The method was tested numerically and experimentally beforehand using a simplified model without rotation or blade passages. In this paper, the validation of the method using a model of a turbine stage is shown. Reynolds-averaged...
-
Strength analysis of the support structure of the offshore wind turbine
PublicationThe global power demand from renewable sources is growing. One of a very favorable solution which meets severe environmental protection requirements are the offshore wind turbines. The offshore wind energy sector has experienced very fast development over last decade. Offshore wind farms, in comparison with onshore applications, can provide increased efficiency with reduced noise, visual, transportation and installation con-flicts....
-
Investigation of the Aerodynamics of an Innovative Vertical-Axis Wind Turbine
PublicationThe paper presents the results of an experimental investigation and a three dimensional numerical analysis of the transient aerodynamic phenomena occurring in the innovative modification of classic Savonius wind turbine. An attempt to explain the increased efficiency of the innovative design a comparison with the traditional solution is undertaken. A vorticity measure based on the integral of the velocity gradient tensor second...
-
TWO-SHAFT GAS TURBINE TEACHING AND TESTING STATION
PublicationThe station was established as part of a project co-financed by the European Union with the funds of the European Regional Development Fund as part of the Infrastructure and Environment Operational Programme titled: “Establishment of state-of-the-art technical infrastructure for the Engineers of the Future learning programme at the Gdańsk University of Technology” executed in 2013-2015.
-
On the internal efficiency of a turbine stage: classical and CFD definitions
PublicationAlmost entire fleet of steam turbines in Poland was designed between 1950 – 1980 with the use of the so-called zero dimensional (0D) calculation tools. For several years, design and modernization of the turbines occur in assistance with the state of the art methods that describe working fluid flow field based on 3D models and CFD codes. This cooperation between 0D and 3D codes requires exchange of overall, integral information...
-
Explanation of Reduction of Pressure Forces in Turbine Chamber Seals
PublicationThe paper describes a chamber seal reducing the aerodynamic forces created in shroud seals. Asymmetrical pressure distribution (due to rotor-stator eccentricity) in the blade tip clearance leads to the creation of pressure forces acting on the blade shroud. By increasing the volume above the shroud, the pressure distribution becomes more uniform on the whole shroud circumference and the effect of rotor eccentricity is reduced....
-
APPLICABILITY OF INLET AIR FOGGING TO MARINE GAS TURBINE
PublicationThe dependency of marine gas turbine on the ambient temperature leads to a decrease of the gas turbine power output in arid areas. Very often gas turbine power output demand is high and the power margins originally designed into the driver , has been exhausted. In such circumstances the inlet air fogging is an effective compensation of gas turbine power. In this paper an analysis of inlet air fogging applicability to marine gas...
-
INFLUENCE OF INLET GEOMETRY ON THE EFFICIENCY OF 1MW STEAM TURBINE
PublicationThe process of the design of the 1MW steam turbine includes designing the stator and rotor blades, the steam turbine inlet and exit, the casing and the rotor. A turbine that operates at rotation speeds other than 3000 rpm requires a gear box and generator with complex electronic software. This paper analyses the efficiency of eight turbine variants, including seven inlet geometries and three stages of stator as well as an eight...
-
Explanation of Reduction of Pressure Forces in Turbine Chamber Seals
PublicationThe paper describes a chamber seal reducing the aerodynamic forces created in shroud seals. Asymmetrical pressure distribution (due to rotor-stator eccentricity) in the blade tip clearance leads to the creation of pressure forces acting on the blade shroud. By increasing the volume above the shroud, the pressure distribution becomes more uniform on the whole shroud circumference and the effect of rotor eccentricity is reduced....
-
Kinetic analysis of the stage for a high speed steam turbine
PublicationThis article analyzes possibilites of resonances within a control stage for a high speed steam turbine. This stage hase been based on assembling of a single blade to a rotating disk and increasing of rigidity of the system by using of a bandage. In the analysis will be nd a possiblity of resonance frequency, and mistuning by showing safety working ranges. The calculations have bean used the3D modal and harmonic analysis by the...
-
Suitableness of SLM Manufactured Turbine Blade for Aerodynamical Tests
PublicationsettingsOrder Article Reprints Open AccessArticle Suitableness of SLM Manufactured Turbine Blade for Aerodynamical Tests by Janusz Telega 1,*ORCID,Piotr Kaczynski 1ORCID,Małgorzata A. Śmiałek 2ORCID,Piotr Pawlowski 3ORCID andRyszard Szwaba 1ORCID 1 Institute of Fluid Flow Machinery Polish Academy of Sciences (IMP PAN), Fiszera 14, 80-231 Gdansk, Poland 2 Faculty of Mechanical Engineering and Ship Technology, Institute of Naval...
-
Badanie parametrów pracy laboratoryjnej instalacji pompy ciepła powietrze-woda typu monoblok
Publication -
Oddziaływania międzycząsteczkowe w wybranych układach trójskładnikowych: woda - osmolit - model łańcucha białkowego
PublicationW niniejszej rozprawie przedstawione zostały wyniki moich prac nad oddziaływaniami międzycząsteczkowych w wodnych układach osmolitów i białek. Wykorzystałam równolegle dwa kierunki badań: spektroskopię w podczerwieni (FTIR) oraz badania wolumetryczne i akustyczne. Mając możliwość śledzenia formowania się włókien amyloidowych, postanowiłam zbadać również wpływ wytypowanych osmolitów na proces formowania się włókien białkowych. Najważniejszym...
-
Instrumenty ekonomiczne gospodarki wodnej w świetle projektu ustawy prawo wodne z czerwca 2016
Publication -
Optymalizacja działania wybranych układów kombinowanych silnik o zapłonie samoczynnym - turbina parowa
PublicationW artykule przedstawiono optymalizację wybranych układów kombinowanych silnik o zapłonie samoczynnym – turbina parowa. Do rozważań przyjęto układy kombinowane z kotłem utylizacyjnym jednociśnieniowym, z obiegiem jednociśnieniowym zawierającym dodatkowy odparownik niskoci-śnieniowy zasilający odgazowywacz oraz z obiegiem dwuciśnieniowym. Porównano uzyskane dodat-kowe moce, sprawności z wykorzystaniem ciepła zawartego w spalinach...
-
Rynek turbin i silników gazowych na świecie.
PublicationW artykule przedstawiono światowe tendencje w zakresie instalacji turbin i silników gazowych oraz omówiono najważniejsze czynniki związane z szerszym wykorzystaniem gazu ziemnego w energetyce. Zwrócono uwagę na wzrost zainteresowania układami skojarzonymi oraz energią odnawialną.
-
SYSTEM RADIOLOKALIZACYJNY OPARTY NA FARMIE TURBIN WIATROWYCH
PublicationW referacie zaproponowano wykorzystanie farmy turbin wiatrowych do budowy systemu radiolokalizacyjnego dla obiektów latających (samolotów). Zaproponowane rozwiązanie umożliwia oszacowanie położenia obiektu w przestrzeni, zwłaszcza w ruchu, za pomocą sygnałów lokalizacyjnych nadawanych asynchronicznie z wież turbin wiatrowych. Przedstawiono matematyczną analizę metody oraz wyniki badań symulacyjnych efektywności pracy rozwiązania...
-
ANALIZA PARAMETRÓW PRZEPŁYWOWYCH PRZEZ STOPNIE TURBIN PAROWYCH
PublicationTurbina w obiegach cieplnych pracuje w zmienionych warunkach. Dodatkowo zmianie ulegają strumienie mas czynnika roboczego z powodu chłodzenia (w turbinach gazowych) lub poboru pary do układu regeneracji ciepła (w turbinach parowych). Te dopływy i pobory również zależą od obciążenia turbozespołu. Stąd w obliczeniach numerycznych wieńców wirnikowych dla wyznaczenia stanów referencyjnych, podobnie jak dla turbin gazowych, trzeba uwzględnić...
-
Analiza sposobów chłodzenia układów łopatkowych turbin gazowych
PublicationReferat stanowi analizę najczęściej spotykanych sposobów chłodzenia układów łopatkowych w turbinach gazowych. W artykule przedstawiono schematy ilustrujące sposób chłodzenia a tak że przepływ strumienia słodzącego w układzie łopatkowym. Uwagę poświęcono głównie układom bez wymuszenia czyli konwekcyjnym.
-
Turning ability of hydrofoil crafts
PublicationPrzedstawiono metodę pozwalającą wyznaczać średnicę taktyczną, kąt przechyłu i kąt dryfu oraz siłę poprzeczną na sterze podczas ustalonej cyrkulacji wodolotu. W tym celu opracowano układ równań opisujących ruch wodolotu w płaszczyźnie poziomej. Współczynniki równań są wyznaczane na podstawie głównych parametrów geometrycznych jednostki oraz płatów. Przeprowadzono także szereg obliczeń dla różnych konfiguracji płatów oraz zespołu...
-
BADANIE EFEKTYWNOŚCI WYKRYWANIA ANOMALII PROCESOWYCH W DZIAŁANIU TURBINY PAROWEJ ELEKTROWNI JĄDROWEJ PRZY POMOCY METOD WIELOWYMIAROWEJ ANALIZY STATYSTYCZNEJ
PublicationW artykule przedstawiono analizę możliwości wykrywania anomalii procesowych w działaniu turbiny parowej elektrowni jądrowej przy pomocy metod wielowymiarowej analizy statystycznej. Zasymulowano symptomy dwóch rodzajów uszkodzeń turbiny parowej tj. uderzenie wodne oraz, wyciek pary z zaworu części niskoprężnej. Jako narzędzie diagnostyczne wykorzystano Metodę Składników Podstawowych PCA (z ang. Principal Component Analysis). Jako...
-
Damage detection in turbine wind blades by vibration based methods
PublicationThe paper describes results of numerical simulation for damage localization in the composite coat of a wind turbine blade usingmodal parameters and a modern damage detection method (wavelet transform).
-
Turbinka pneumatyczna jako maszyna ekspansyjna w obiegu ORC
Publication -
Application of Artificial Neural Networks in Investigations of Steam Turbine Cascades
PublicationZaprezentowano wyniki badań numerycznych zastosowania sieci neuronowych przy obliczeniach przepływów w palisadach turbin parowych. Na podstawie uzyskanych wyników wykazano, że sieci neuronowe mogą być używane do szacowania przestrzennego rozkładu parametrów przepływu, takich jak entalpia, entropia, ciśnienie czy prędkość czynnika w kanale przepływowym. Omówiono również zastosowania tego typu metod przy projektowaniu palisad, stopni...
-
The Method of reduction of aerodynamic forces generated in turbine blade seals
PublicationThe distibution of pressure in the seal gaps does not only affect the so called '' leakage losses'' and the turbine stage overall efficiency but also plays an important role in the generation of aerodynamic forces which may cause self-excited rotor vibrations. The paper describes a chamber seal applied for the reduction of the aerodynamic forces created in shroud seals. This kind of turbine seal was patented and tested.
-
1D Model Callibration on the Basis on 3D calculations for Tesla Turbine
PublicationThe paper presents the system of equations for axisymmetriclaminar flow, after averaging, through the width of interdisk slit ofTesla turbine. Coefficients were introduced, as a result ofaveraging, that improve the efficiency of 1D model. The minimalnumber of such coefficients was determined. The 1D modelmakes it possible to attain analytical solutions to an accuracylimited by these coefficients. Calibration of 1D model depends...
-
Modeling of a Combined Cycle Gas Turbine Integrated with an Adsorption Chiller
Publication -
Gas turbine as ship prime mover - specific problems and prospects.
PublicationPrzedstawiono ewentualne możliwości zastosowania turbin gazowych w okrętownictwie. Analizowano aspekty ekologiczne, ekonomiczne i techniczne.
-
Hydraylic turbine development vor lov-output power plants.
PublicationPraca zawiera wyniki badań nowego układu przepływowego turbiny wodnej, na tle krytyki stosowanych powszechnie technologii w hydroenergetyce. Pokazano efekty energetyczne pracy turbiny i kształt kinematyki przepływu w jej kanałach hydraulicznych. Pokazano również skutki stosowania metody optymalizacyjnej dla osiągania wyższych sprawności pracy wirnika turbiny.
-
Flows in turbine blade seals: CFD calculations versus experiment
PublicationPrzedstawiono wyniki numerycznej analizy przepływu w uszczelnieniu nadbandażowym stopnia turbinowego. Rezultaty obliczeń porównano z danymi doświadczalnymi. Eksperymenty przeprowadzono na modelowej turbinie powietrznej przy różnych częstościach obrotów wału i różnym obciążeniu turbiny.
-
NUMERYCZNY MODEL OBLICZENIOWY OBIEGU TURBINY KLASY 300 MW
PublicationNiniejszy artykuł stanowi opis modelu obiegu cieplnego turbiny o mocy 360MW, utworzonego w preprocesorze numerycznego programu obliczeniowego onazwie DIAGAR. Zadaniem opisywanego modelu jest odtwarzanie zjawisk fizycznych zachodzących w poszczególnych urządzeniach składowych obiegu, zarówno podczas poprawnej (sprawnej) pracy bloku energetycznego, jak i w przypadku pojawienia się niesprawności. Utworzony...
-
Dynamic state assessment of the water turbine with the power of 600 kW
PublicationThe article discusses the results of experimental studies to assess the dynamic state of the turbine set with the Kaplan turbine. The dynamic assessment was made on the basis of appropriate standards, based on the measurement results of selected parameters of vibration, which have been measured for several states of the machine load. In addition, we attempted to identify the causes of the increased vibration levels based on the...
-
The thermal effort during marine steam turbine flooding with water
PublicationThe work discussed an extreme case of cooling a steam turbine. The ship's steam turbine was used as an example. In marine transport units with low-speed engines dominate, however, there are also units with steam turbines. An example of analysed marine steam turbine is shown in Fig. 1. When considering the issue of cooling steam turbines, it is necessary to estimate the extreme conditions that may occur during operation of the turbine....
-
Numerical investigation on the performance of a small counter-rotating wind turbine
PublicationThe article presents the results of the investigation on the performance of a small counter-rotating wind turbine. The wind turbine has been simulated using Computational Fluid Dynamics methods. Actuator Line Model has been successfully used to represent rotors in the computational domain. A parametric study has been carried out, taking into account changes in the tip speed ratio of the rotors while maintaining a constant distance...
-
Shape Optimisation of Kaplan Turbine Blades Using Genetic Algorithms
PublicationThis monograph is a comprehensive guide to a method of blade profile optimisation for Kaplan-type turbines. This method is based on modelling the interaction between rotor and stator blades. Additionally, the shape of the draft tube is investigated. The influence of the periodic boundary condition vs. full geometry is also discussed. Evolutionary algorithms (EA) are used as an optimisation method together with artificial neural...
-
Turbiny wiatrowe o pionowej osi obrotu - wirnik Savoniusa
PublicationReferat stanowi krótki przegląd turbin wiatrowych o osi pionowej, ze szczególnym uwzględnieniem wirnika Savoniosa. Głównym celem artykułu jest poznanie różnych wariantów, w jakich występuje wirnika Savoniosa oraz znalezienie najsprawniejszego typu. Z licznych możliwości modyfikacji owego wirnika jako pierwsza została zaprezentowana opcja ze zmiennymi końcówkami turbiny. Przepływ przez szczelinę międzyłopatkową będzie wybrany jako...
-
Analysis of diagnostic informativeness of the exhaust temperature of a naval gas turbine
PublicationThe conducted investigations aimed to carry out an analysis of the possibility that the failures identification in the automatic control system of a gas turbine engine could be worked out on the basis of measurements of the exhaust stream temperature behind the gas generator. The exhaust temperature represents a basic control parameter, enabling technical state evaluation of the engine within the operation process, which is observed...
-
The Method of Reduction of Aerodynamic Forces Generated in Turbine Blade Seals
PublicationOpisano metodę zmniejszania sił wymuszających drgania aerodynamiczne poprzez zastosowanie nowego uszczelnienia nadbandażowego typu komorowego. Efektywność stosowania uszczelnienia komorowego potwierdzono obliczeniami numerycznymi i badaniami eksperymentalnymi.
-
Tesla Friction-Type Micro Turbine For Small-Scale Cogeneration
PublicationTesla turbine is rarely used in professional power installations due to its specific work characteristics and relatively low internal efficiency. However, it has some potential to be applied in micro-power plants operating in distributed co-generation systems, also working in an organic Rankine cycle. This paper presents results from numerical calculations of flow in three models of Tesla disk turbines assuming nitrogen as a working...
-
Wzrost sprawności turbiny gazowej przez zastosowanie idei Szewalskiego
PublicationW artykule przedstawiono wpływ zastosowania upustu na sprawność turbiny gazowej. Upust w turbinie zrealizowano według idei prof. Roberta Szewalskiego, która polega na zastosowaniu upustu międzystopniowego w turbinie gazowej do podgrzewu powietrza zasilającego komorę spalania. Dzięki przeprowadzonej modyfikacji osiąga się wzrost sprawności obiegu oraz spadek zużycia paliwa. Analiza numeryczna obiegu cieplnego przed i po modernizacji...
-
Innovative Turbine Intake Air Cooling Systems and Their Rational Designing
PublicationThe improved methodology of the engine intake air cooling system designing based on the annual effect due to cooling was developed. It involves determining the optimal value of cooling capacity, providing the minimum system sizes at maximum rate of annual effect increment, and its rational value, providing a close to maximum annual effect without system oversizing at the second maximum rate of annual effect increment within the...
-
OBTAINING FLUID FLOW PATTERN FOR TURBINE STAGE WITH NEURAL MODEL.
PublicationIn the paper possibility of applying neural model to obtaining patterns of proper operation for fluid flow in turbine stage for fluid-flow diagnostics is discussed. Main differences between Computational Fluid Dynamics (CFD) solvers and neural model is given, also limitations and advantages of both are considered. Time of calculations of both methods was given, also possibilities of shortening that time with preserving the accuracy...
-
Parametric Study on a Performance of a Small Counter-Rotating Wind Turbine
PublicationA small Counter-Rotating Wind Turbine (CRWT) has been proposed and its performancehas been investigated numerically. Results of a parametric study have been presented in this paper.As parameters, the axial distance between rotors and a tip speed ratio of each rotor have been selected.Performance parameters have been compared with reference to a Single Rotor Wind Turbine (SRWT).Simulations were carried out with Computational Fluids...
-
Wyznaczenie maksymalnej sprawności obiegu zeroemisyjnej turbiny gazowo-parowej
PublicationW pracy omówiono koncepcję zeroemisyjnej turbiny gazowo-parowej z zastosowaniem oksyspalania
-
The European Union's Water Framework Directive - A new challenge in monitoring water quality. Ramowa Dyrektywa Wodna Unii Europejskiej - Nowe wyzwanie w monitoringu jakości wody
PublicationMonitoring jakości wody polega zwykle na punktowym pobieraniu próbek z użyciem odpowiednich próbników, po którym następuje etap analizy w celu określenia stężenia zanieczyszczeń. Pomimo wielu zalet, metoda ta ma ograniczenia w zakresie badania rozkładu czasowego i przestrzennego zanieczyszczeń oraz w zakresie oceny biodostępności zanieczyszczeń. Wdrożenie Ramowej Dyrektywy Wodnej (2000/60/EC)w krajach Unii Europejskiej będzie wymagało...
-
Ograniczenie zanieczyszczeń odprowadzanych do Bałtyku przez rozwiązania zrównoważonej gospodarki wodno-ściekowej na obszarach wiejskich
PublicationMorze Bałtyckie jest prawie całkowicie zamknięte. W każdym roku tylko 3% objętości wody ulega wymieniane. Dlatego okres całkowitej wymiany wody w morzu jest bardzo długi i wynosi 25-30 lat. Powoduje to nagromadzenie dopływających zanieczyszczeń i przyczynia się do eutrofizacji. Czynnikami odpowiedzialnymi za eutrofizację są związki biogenne, przede wszystkim związki azotu i fosforu. Jeśli chodzi o zasilanie wód Bałtyku związkami...
-
Wytwarzania energii z wody na obiektach o bardzo niskich spadach
PublicationW referacie przedstawiono sposób pozyskiwania energii z wody oraz wykorzystanie zasobów technicznych w Polsce. Następnie opisano rodzaje turbin wodnych. W dalszej części przedstawiono rurową turbinę wodną z wirnikiem Kaplana oraz ślimaka Archimedesa, jako technologie wytwarzające energię z wody na obiektach o bardzo niskich spadach. Na końcu opisano perspektywy wykorzystania w przyszłości coraz niższych spadów
-
Ocena naprężeń w regenerowanych korpusach parowych turbin energetycznych.
PublicationPrzedstawiono wyniki badań naprężeń własnych w ścianach korpusów turbin poddanych procesowi reparacji przez zaspawanie. Wykorzystano do badań metodę wykorzystujacą efekt Barkhausena oraz - dla kontrolo - metodę nawiercania otworów (metoda Mathar'a). Dwa rezultaty badań są istotne: 1) stwierdzono niski stan naprężeń w strefie reperowanej - co dowodzi poprawnej technologii; oraz 2) - uzyskano bardzo dobrą zgodność poziomów naprężeń...
-
Układy chłodzenia oleju smarującego łożyska wzdłużne turbin wodnych
PublicationOmówiono charakterystyczne cechy wewnętrznych i zewnętrznych układów chłodzenia oleju smarującego hydrodynamiczne łożyska wzdłużne w turbinach wodnych o wałach pionowych. Zaprezentowano także problemy związane z projektowaniem zewnętrznych układów chłodzenia. Na przykładzie układu chłodzenia hydrozespołu nr 2 elektrowni szczytowo-pompowej (esp) Żar omówiono efekty stosowania zewnętrznych układów chłodzenia.