Filters
total: 2826
filtered: 2418
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: OPTICAL PUMPING
-
Forecasting of railway track tamping based on settlement of sleepers using fuzzy logic
PublicationThe sleepers in a railway track transfer vertical, transverse and longitudinal loads to the track ballast and subgrade. The sleepers allow for keeping the distance between the rails constant. The thickness of ballast should be between 16 and 35 cm depending on the design standard of the track, and it should be densified where the ballast supports the sleeper. The exploitation causes contamination of the ballast, crushing the material...
-
Effective Formula for Impact Damping Ratio for Simulation of Earthquake-induced Structural Pounding
PublicationStructural pounding during earthquakes may cause substantial damage to colliding structures. The phenomenon is numerically studied using different models of collisions. The aim of the present paper is to propose an effective formula for the impact damping ratio, as a parameter of the impact force model used to study different problems of structural pounding under seismic excitations. Its accuracy has been verified by four various...
-
Optical and structural properties of polycrystalline CVD diamond films grown on fused silica optical fibres pre-treated by high-power sonication seeding
PublicationIn this paper, the growth of polycrystalline chemical vapour deposition (CVD) diamond thin films on fused silica optical fibres has been investigated. The research results show that the effective substrate seeding process can lower defect nucleation, and it simultaneously increases surface encapsulation. However, the growth process on glass requires high seeding density. The effects of suspension type and ultrasonic power were...
-
Radiation dose distributions in three dimensions from tomographic optical density scanning of polymer gels: II. Optical properties of the BANG polymer gel
Publication -
Effects of Flywheel vs. Free-Weight Squats and Split Squats on Jumping Performance and Change of Direction Speed in Soccer Players
Publication -
High Speed Milling vibration surveillance with optimal spindle speed based on optimal speeds map
PublicationThe paper presents the method of the surveillance of the self-excited chatter vibration. At first, the workpiece modal parameters are estimated based on experimental data which leads to verification of computational model. Then, for selected surface points optimal spindle speeds are calculated. By considering sufficient amount of points it is possible to build a map of optimal spindle speeds. Experimental results show that this...
-
Practical issues for the implementation of survivability and recovery techniques in optical networks
PublicationFailures in optical networks are inevitable. They may occur during work being done for the maintenance of other infrastructures, or on a larger scale as the result of an attack or large-scale disaster. As a result, service availability, an important aspect of Quality of Service (QoS), is often degraded. Appropriate fault recovery techniques are thus crucial to meet the requirements set by the Service Level Agreements (SLAs) between...
-
Multi-layered tissue head phantoms for noninvasive optical diagnostics
PublicationExtensive research in the area of optical sensing for medical diagnostics requires development of tissue phantoms with optical properties similar to those of living human tissues. Development and improvement of in vivo optical measurement systems requires the use of stable tissue phantoms with known characteristics, which are mainly used for calibration of such systems and testing their performance over time. Optical and mechanical...
-
Polarization-sensitive optical coherence tomography for ceramic materials inspection
PublicationCeramics production is looking for a fast, reliable and non-destructive method that can be implemented on site for defect detection and analysis. In this paper we present polarization-sensitive optical coherence tomography (PS-OCT) as a method for defect inspection. Proposed extensions to standard OCT provide additional information for complete characterization of tested object. We compare OCT and microscope imaging that can easily...
-
New aspects of the use of Optical Theorem in the analysis of microcavity lasers
Publication -
Modeling of broadband light source to use with optical coherenttomography system
PublicationW pracy przedstawiono modelowanie źródeł szerokopasmowych na potrzeby systemów koherentnej tomografii optycznej z punktu widzenia uzyskiwanej zdolności podłużnej i jakości otrzymywanych obrazów. Pokazano na przykładzie źródła szerokopasmowego wykorzystującego światłowód fotoniczny do generacji w wyniku zjawisk nieliniowych ''supercontinuum'' wpływ kształtowania wiązki na możliwości pomiarowe systemu OCT.
-
Applying of the optical time-of-flight spectroscopy for the paper and pulp characterization
PublicationW pracy przedstawiono korzyści wykorzystania optycznej spektroskopii czasu przelotu w badaniach papieru i miazgi drzewnej. Przedmiotem badań były różne gatunki papieru oraz miazgi drzewnej (bez obróbki cieplnej, po obróbce cieplnej lub po obróbce chemicznej). W pomiarach wykorzystano półprzewodnikowe lasery impulsowe oraz w charakterze fotoodbiorników kamerę smugową lub licznik fotonów.
-
Joint optimization of anycast and unicast flows in survivable optical networks
PublicationZnane z literatury dotychczasowe prace związane z ochroną ruchu przed awarią elementów sieci dotyczą transmisji typu unicast (jeden-do-jednego). Niniejszy artykuł jest pierwszym prezentującym rozwiązanie jednoczesnej ochrony transmisji anycast (jeden-do-jednego-z-wielu) oraz transmisji unicast. Proponowane podejście wykorzystuje model ochrony ścieżki (ang. path protection). Zagadnienie zostało sformułowane w postaci odpowiedniego...
-
<title>Basic properties of ring-index optical fibers</title>
Publication -
Hybrid Integrated Components For Optical Fiber Communication And Instrumentation Systems
Publication -
Technological Sensitizing Of Mosaic Optical Fibres For Sensory And Microoptics Applications
Publication -
<title>Apparatus to search for optical flashes of astronomical origin</title>
Publication -
<title>Technology of soft-glass optical fiber capillaries</title>
Publication -
Research Toward The Optical Equipment For An Autonomous Robot For TviV Environment
Publication -
Cationic porphyrazines with morpholinoethyl substituents – Syntheses, optical properties, and photocytotoxicities
Publication -
In-situ optical diagnostics of boron-doped diamond films growth
PublicationInterferometry is a desirable method for in-situ measurement of thin, dielectric film growth, as it don't modify conditions of film deposition. Here we present interferometrical measurements of thickness of doped diamond films during Chemical Vapor Deposition (CVD) process. For this purpose we used a semiconductor laser with a 405nm wavelength. Additional ex-situ measurement using spectral interferometry and ellipsometry...
-
Parallel multithread computing for spectroscopic analysis in optical coherence tomography
PublicationSpectroscopic Optical Coherence Tomography (SOCT) is an extension of Optical Coherence Tomography (OCT). It allows gathering spectroscopic information from individual scattering points inside the sample. It is based on time-frequency analysis of interferometric signals. Such analysis requires calculating hundreds of Fourier transforms while performing a single A-scan. Additionally, further processing of acquired spectroscopic information...
-
Polarization sensitive optical coherence tomography for technical materials investigation
Publication -
<title>Synthesized light source for optical coherence tomograph</title>
Publication -
Modeling of multi-cavity Fabry-Perot optical fiber sensors
PublicationReflectance characteristics of a two-cavity extrinsic Fabry-Perot optical fiber sensor were investigated using computer modeling. Calculations were performed using a plane wave-based approach, selected for clarity of results. Based on the modeling results, it can be concluded that the two-cavity Fabry-Perot interferometer can be used to measure two different quantities, such as refractive index and temperature, independently. It...
-
Polarization sensitive optical coherence tomography for technical materials investigation
PublicationZaprezentowano system optycznej tomografii koherentnej z analizą stanu polaryzacji światła. System umożliwia nieniszczące i bezkontaktowe badanie wewnętrznej struktury materiałów warstwowych. Przedstawiono zastosowaną metodę analizy stanu polaryzacji promieniowana wstecznie rozproszonego od badanego obiektu.
-
Reference LED source of subnanosecond pulses of broadband optical radiation
Publication -
Poll Reader - the working prototype of optical mark recognition software
PublicationAutomatyczne rozpoznawanie zaznaczeń wydaje się stosunkowo prostym zadaniem z dziedziny przetwarzania dokumentów, a komercyjne systemy OMR są dostępne na rynku już od dłuższego czasu. Zdecydowaliśmy się jednak na stworzenie prostego darmowego oprogramowania, które mogłoby być wykorzystywane przez uczelnie zobowiązane do przeprowadzania ankiet wśród studentów. W rozdziale opisano konstrukcję programu oraz najważniejsze algorytmy...
-
Mode interaction in few-mode optical fibres with Kerr effect
PublicationUogólnioną metodę rzutowania do ortogonalnej bazy funkcji poprzecznej współrzędnej Bessela stosuje się do wyprowadzania układów równań nieliniowych Schrodingera. Teoria jest ważna dla paczek falowych w światłowodach i kilku modelach.
-
Influence of sensor design and optical properties of tissue on the photoplethysmographic signal
PublicationPhotopletysmography and an associated technique called pulse oximetry are still explored due to the expectations that they give a lot of information about the state of the patient and, also, due to the fact that they are non invasive. Knowledge about the impact of various parameters on the measured signal leads to a faster and a more reliable way of analyzing measurement results and finding the dependencies between the involved...
-
Polarization Conversion of Solitons Propagating in Birefringent Microstructured Optical Fibers
Publication -
Numerical modelling of conical wave formation in multimode optical fibers
Publication -
Observation of second-order meron polarization textures in optical microcavities
Publication -
Thermal and optical properties of PMMA films reinforced with Nb2O5 nanoparticles
Publication -
The Investigation of Thermal and Optical Properties of Semiconducting Nanostructural Hybrid Films
Publication -
Optical properties of phenylene–thiophene-based polyazomethine thin films
Publication -
Selective Protection for All-Optical Physical Impairment Constrained Routing
PublicationW przypadku sieci optycznych, zauważalna jest obecnie tendencja dążenia do transmisji całowicie optycznej (tz. bez konwersji O/E/O w węzłach tranzytowych). Jednakże w niedalekiej przyszłości, z uwagi na techniczne ograniczenia, niemożliwa będzie obsługa całości ruchu wyłącznie w dziedzinie optycznej. Operatorzy będą więc zainteresowani oferowaniem rozwiązań przejściowych implikujących przełączanie w dziedzinie optycznej jedynie...
-
Liveness measurements using optical flow for biometric person authentication
PublicationAutomatyczne rozpoznawanie twarzy jest jedną z najpopularniejszych technik biometrycznych, jednak nawet najdokładniejsze algorytmy identyfikacji okażą się bezużyteczne, jeśli będzie można je oszukać, np. używając zdjęcia zamiast rzeczywistej osoby. Dlatego też odpowiedni pomiar żywotności jest niezwykle istotny. W pracy zaprezentowano metodę, która jest w stanie rozróżnić pomiędzy sekwencjami wideo pokazującymi żywe osoby oraz...
-
Impact of Selected Operating Conditions on the Optical Properties of Polymer Shields
Publication -
Second- and Third-Order Nonlinear Optical Response of Perovskite LiTaO3
Publication -
Laser operated nonlinear optical studies of BiFe0,9Cr0,1O3 and BiFe0,9Al0,1O3 multiferroics
Publication -
Optical time of flight spectroscopy for highly scattering materials measurements.
PublicationW artykule omówiono możliwości wykorzystania optycznej spektroskopii czasu przelotu w wyznaczaniu podstawowych parametrów optycznych materiałów silnie rozpraszających światło. Wykorzystano tu metodę Monte Carlo i metodę dyfuzji.
-
Optical excitation methods in active dynamic thermography in medical diagnostics.
PublicationArtykuł zawiera opis metod pobudzania cieplnego badanych obszarów ciała ludzkiego w technice aktywnej termografii dynamicznej. Jako źródła pobudzenia cieplnego mogą być stosowane lampy podczerwieni, lampy halogenowe dużej mocy, a także lasery. W artykule opisano również algorytmy obliczeń obrazów parametrycznych.
-
Optical measurements for thin oil film investigation in rheometric processes.
PublicationPrzedmiotem badań jest pomiar parametrów cienkiej warstwy oleju silikonowego AK106, powstającej na ścianach dyszy w trakcie procesu reologicznego wyciskania do form past ceramicznych, przygotowywanych ze sproszkowanego tlenków wodorotlenków AlOOH oraz oleju AK106. Parametrami badanymi były: grubość warstwy oleju, charakterystyka reflektancyjna pasty oraz skład mieszaniny. Przedstawione zagadnienie ma istotne znaczenie dla rozwoju...
-
Optical monitoring of thin oil film thickness in extrusion processes
PublicationPraca porusza problem pomiaru grubości cienkiej warstwy przyściennej -oleju, podczas procesu wyciskania ceramiki modelowej. Szczegółowo opisuje zjawiska fizyczne zachodzące w warstwie przyściennej oraz dynamiczne parametry wykorzystywane do oceny grubości. Autorzy opisują także metodę pomiaru oraz konstrukcję układów pomiarowych.
-
Efficient finite difference analysis of microstructured optical fibers [on line]
PublicationW pracy przedstawiono nową technikę numerycznej analizy mikrostruktur światłowodowych. Technika ta polega na połączeniu metody różnic skończonych i dyskretnych rozwinięć funkcyjnych. Pozwala to na zmniejszenie rozmiaru macierzy powstających przy analizie problemu, a jednocześnie na bezpośrednią implementację radiacyjnych warunków brzegowych. Testy algorytmu przeprowadzono dla kilku wybranych struktur, uzyskując bardzo dobrą zgodność...
-
Microcrystalline diamond film evaluation by spectroscopic optical coherence tomography
PublicationThis study has focused on the microcrystalline diamond film (MCD) thickness evaluation. For this purpose, optical coherence tomography (OCT) enhanced by spectroscopic analysis has been used as a method of choice. The average thickness of the tested layer was about 1.5 µm, which is below the standard 2-point OCT resolution. In this case, the usefulness of the spectroscopic analysis was confirmed for the evaluation of the thickness...
-
Surface quality control of a thin SiN layer by optical measurements
PublicationFiber optic interferometers have a wide range of applications, including biological and chemical measurements. Nevertheless, in the case of a reflective interferometer setup, standard silver mirrors cannot be used in every measurement, due to their chemical activity. This work investigates the surface quality of a thin optical layer of silicon nitride (SiN), which can serve as an alternative material for silver mirrors. We present...
-
Spectroscopic Optical Coherence Tomography for Thin Layer and Foil Measurements
PublicationThe main goal of this research was to assess if it is possible to evaluate the thickness of thin layers (both thin films on the surface and thin layers below the surface of the tested object) and foils using optical coherence tomography (OCT) for thickness assessment under the resolution of the standard commercially available OCT measurement system. In the proposed solution, light backscattered from the evaluated thin layer has...
-
Nitrogen-Doped Diamond Film for Optical Investigation of Hemoglobin Concentration
PublicationIn this work we present the fabrication and characterization of a diamond film which can be utilized in the construction of optical sensors for the investigation of biological samples. We produced a nitrogen-doped diamond (NDD) film using a microwave plasma enhanced chemical vapor deposition (MWPECVD) system. The NDD film was investigated with the use of scanning electron microscopy (SEM), atomic force microscopy (AFM) and Raman...