displaying 1000 best results Help
Search results for: RESIDUAL MAGNETIZM
-
JOURNAL OF MAGNETISM AND MAGNETIC MATERIALS
Journals -
Numerical Analysis of Magnetic Core Properties Influence on Residual Current Device Behaviour
PublicationW artykule przedstawiono analizę wpływu kształtu prądu w uzwojeniu pierwotnym transformatora prądowego na pracę przekładnika różnicowo-prądowego. Przeprowadzono obliczenia symulacyjne dla wymuszenia o kształcie sinusoidy i sinusoidy wyprostowanej dla częstotliwości 50 Hz. Wzięto pod uwagę dwa typy charakterystyki magnesowania transformatora: dla materiału magnetycznie miękkiego i materiału o prostokątnej pętli histerezy. Analiza...
-
IEEE TRANSACTIONS ON MAGNETICS
Journals -
Discussion of Derivability of Local Residual Stress Level from Magnetic Stray Field Measurement
PublicationThe NDT procedure dubbed ‘metal magnetic memory’ method and the related ISO 24497 standard has found wide industrial acceptance in some countries, mainly in Russia and China. The method has been claimed by some researchers (Roskosz and Bieniek in NDT&E Int 45:55–62, 2012; Wilson et al. in Sens Actuators A 135:381–387, 2007) as having potential for quantitative determination of local residual stress state in engineering structures,...
-
Residual MobileNets
PublicationAs modern convolutional neural networks become increasingly deeper, they also become slower and require high computational resources beyond the capabilities of many mobile and embedded platforms. To address this challenge, much of the recent research has focused on reducing the model size and computational complexity. In this paper, we propose a novel residual depth-separable convolution block, which is an improvement of the basic...
-
Comparison of residual current devices tripping characteristics for selected residual current waveforms
PublicationZgodnie z normami międzynarodowymi, w instalacjach o zwiększonym ryzyku porażenia prądem elektrycznym należy stosować wyłączniki różnicowoprądowe wysokoczułe. Dla zapewnienia skutecznej ochrony przeciwporażeniowej zainstalowany wyłącznik różnicowoprądowy powinien prawidłowo wykrywać określony kształt prądu różnicowego. W artykule przedstawiono charakterystyki działania wyłączników różnicowoprądowych przy wybranych przebiegach odkształconego...
-
Progress in the post weld residual stress evaluation using Barkhausen effect meter with a novel rotating magnetic field probe
PublicationWe report the progress in post weld residual stress evaluation using Barkhausen effect (BE) meter with rotating magnetic field probe. The novel probe of the BE meter contains two C-core electromagnets and searching coil with ferrite antenna. This meter allows automatic measurements of BE intensity envelopes at different angles of magnetizing field. The full process of measurement at given position of the probe takes about only...
-
Journal of Residuals Science & Technology
Journals -
Residual stress evaluation in oil pipeline.
PublicationPrzedstawiono metodę pomiaru rozkładu naprężeń w ropociągu z wykorzystaniem efektu Barkhausena. Opisano procedurę pomiaru oraz kalibracji metody. Wynik potwierdzono w jednym punkcie metodą Mathar´a
-
Residual Current Devices: Selection, Operation, and Testing
PublicationIn this book, the idea for residual current protection has been presented. The evolution in construction types of residual current devices, which has taken place over decades, is discussed. Types and functional properties of the contemporary residual current devices are described. The main parameters of these devices, from the point of view of their selection and application, are indicated. Special constructions of the protective...
-
Method of determining the residual fluxes in transformer core
PublicationThe article presents the method of calculating the residual induction in transformer columns. The method is based on measurement of the magnetic induction in selected points around the transformer core. The values of residual induction are calculated as linear combination of the results of measurement.
-
Security level estimation as a function of residual risks
PublicationArtykuł przedstawia sposób oceny poziomu bezpieczeństwa organizacji IT w oparciu o metodę oceny ryzyka. Opisane są podstawowe kroki wspomnianej metody, proponowane rozwiązania i zastosowania. Zaproponowano prosty sposób oceny bezpieczeństwa systemów informatycznych organizacji w oparciu o wielkość wyznaczoną na podstawie wyliczonego ryzyka rezydualnego tychże systemów.
-
MAGNETIC RESONANCE IN CHEMISTRY
Journals -
Spectroscopic and magnetic studies of highly dispersible superparamagnetic silica coated magnetite nanoparticles
PublicationSuperparamagnetic behavior in aqueously well dispersible magnetite core-shell Fe3O4@SiO2 nanoparticles is presented. The magnetic properties of core-shell nanoparticles were measured with use of the DC, AC magnetometry and EPR spectroscopy. Particles were characterized by HR-TEM and Raman spectroscopy, showing a crystalline magnetic core of 11.5 ± 0.12 nm and an amorphous silica shell of 22 ± 1.5 nm in thickness. The DC, AC magnetic...
-
Propagation in a ferrite cylindrical waveguide magnetized by a two four-pole magnetic fields.
PublicationUżywając metody rodzajów sprzężonych rozwiązano zagadnienie ferrytowego falowodu cylindrycznego magnesowanego poprzecznie w układzie elektronicznie obracanego czterobiegunowego pola magnetycznego. W falowodzie występuje zjawisko dwójłomności i przesunięcia fazy. Badano zmiany stanu polaryzacji fali elektromagnetycznej na wyjściu falowodu o różnej długości. Wyniki wykorzystano do zaprojektowania sekcji półfalowej falowodu, w której...
-
Residual current devices in installations with PV energy sources
PublicationThe paper presents the principles of residual current devices (RCDs) application in photovoltaic (PV) installations. Provisions of standards in this regard are commented on, in particular, attention is drawn to the lack of obligation to use of RCDs in PV installations. The issue of the shape of the earth fault current and the level of leakage currents in such installations are discussed. These factors influence the selection of...
-
Tripping limitations of residual current devices in photovoltaic installations
PublicationIn electrical installations with photovoltaic sources of energy, earth fault current may comprise alternating current component and direct current component. The waveform shape of this earth fault current mainly depends on the point of the fault and the properties of a photovoltaic power electronics converter. The waveform shape of the current influences operation of protection devices, especially tripping threshold of residual...
-
Low-frequency tripping characteristics of residual current devices
PublicationFast development of various types of converters makes their utilization in industry and in domestic installations very common. Due to converters, an earth fault current waveform in modern circuits can be distorted or its frequency can be different than 50/60 Hz. Frequency of earth fault (residual) current influences tripping of residual current devices which are widely used in low voltage systems. This paper presents the behaviour...
-
Microstructure and residual stresses in surface coatings with PTFE reservoirs
PublicationThe paper presents the results of experimental study into the microstructure and changes in residual stresses resulting from sliding and rolling/sliding loaded interaction between metallic surface coatings with embedded PTFE reservoirs and various counter faces. It was found that before testing surface coatings had compressive residual stresses. Molybdenum coating with all types of PTFE reservoirs displayed, as a result of testing,...
-
Residual current devices in electric vehicles charging installations
PublicationThe main requirements of national regulations and international standards regarding protection against electric shock in electric vehicle charging installations are presented. The principles of using residual current devices (RCDs) in such installations are discussed. It is pointed out that RCDs are mandatory equipment for safe charging of electric vehicles. It is noted that the standards require the use of RCDs having an appropriate...
-
Propagation in a ferrite circular waveguide magnetized through a rotary four-pole magnetic field
PublicationOpracowano uproszczony model matematyczny użyteczny do badania zjawisk polowych występujących w falowodzie cylindrycznym magnesowanym czterobiegunowym polem obrotowym. Wykazano, że falowód ten może być wykorzystany jako przesuwnik fazy lub układ zmieniający polaryzację.
-
Magnetism and structure of Li_xCoO2 and comparison to Na_xCoO2
PublicationW pracy dyskutowane są właściwości magnetyczne i strukturalne Li_xCoO2 dla 0.5< x< 1.0. Jon Co +4 znajduje się w stanie wysokospinowym w Li_xCoO2 dla zawartości litu od 0.94 do 1.00 i w stanie niskospinowym dla x od 0.50 do 0.78.
-
Detection of high frequency current components by residual current devices
PublicationThe negative impact of current harmonics on the main components of residual current devices is presented. A solution for the improvement of the operation of residual current devices is proposed.
-
Behavior of residual current devices at frequencies up to 50 kHz
PublicationThe use of residual current devices (RCDs) is obligatory in many types of low-voltage circuits. They are devices that ensure protection against electric shock in the case of indirect contact and may ensure additional protection in the case of direct contact. For the latter purpose of protection, only RCDs of a rated residual operating current not exceeding 30 mA are suitable. Unfortunately, modem current-using equipment supplied...
-
Tripping of F-type RCDs for High-Frequency Residual Currents
PublicationResidual current devices (RCDs) are apparatus commonly used for protection against electric shock in low-voltage electrical installations. They protect people in the case of an earth fault or even in the case of direct contact with the live parts. However, to be effective protective devices, RCDs have to detect residual currents of various waveform shapes which appear in modern electrical installations. For this purpose, RCDs...
-
Remarks on the Subject of Back-Up Protection of Residual Current Devices
PublicationResidual current devices without integral overcurrent protection (RCCBs) are back-up protected by fuses or miniature circuit-breakers (MCBs). If the latter are used, special attention must be given to the coordination between an RCCB and an MCB. This paper indicates probable cases of the aforementioned devices coordination, in which back-up protection of the RCCB is not adequate. A laboratory test has shown that depending on the...
-
The effect of current delay angle on tripping of residual current devices
PublicationPower electronics converters applied in domestic or similar installations may utilize current delay (phase) angle control to change the level of transferred power. Due to application of such types of converters, earth fault current in the installation may be strongly distorted. The current distortion level depends on a value of current delay angle. This delay angle also influences the tripping threshold of residual current devices....
-
Application of residual current devices in electrical installations with frequency converters
PublicationW instalacjach elektrycznych, w których znajdują się przemienniki częstotliwości mogą pojawić się prądy zwarcia doziemnego o różnej częstotliwości lub stałe. Większość wyłączników różnicowoprądowych nie reaguje na tego typu prądy, co powoduje, że ochrona przeciwporażeniowa jest nieskuteczna. W obwodach z przemiennikami częstotliwości mogą pojawiać się przejściowe i ustalone prądy upływowe o znacznych wartościach. Prądy te znacząco...
-
Tripping of F-type RCDs for high-frequency residual currents
PublicationResidual current devices (RCDs) are apparatus commonly used for protection against electric shock in low-voltage electrical installations. They protect people in the case of an earth fault or even in the case of direct contact with the live parts. However, to be effective protective devices, RCDs have to detect residual currents of various waveform shapes which appear in modern electrical installations. For this purpose, RCDs are...
-
Evaluation of time and space distribution of magnetic flux density in a steel plate magnetized by a C-core
PublicationBadano wpływ częstości magnesowania płyty stalowej na rozkład przestrzenny indukcji magnetycznej wewnątrz tej płyty. Rozkład ten oceniano na podstawie pomiaru natężenia emisji magnetoakustycznej a także rozkładu na powierzchni płyty natężenia efektu Barkhausena. Wyniki dyskutowane są ilościowo i porównane z wynikami modelowania metodą elementów skończonych, w której uwzględniono efekt powstawania prądów wirowych.
-
Journal of Magnetics
Journals -
MAGNESIUM RESEARCH
Journals -
Separation of the effects of notch and macro residual stress on the MFL signal characteristics
PublicationMagnetic flux leakage (MFL) distribution for three configurations of samples has been investigated in order to study the influence of notch and plastic deformation separately as well as together. Samples have been made of S355 steel. The MFL signal measurements were carried out along the longest dimension of the sample over a length of 120 mm. Two components of magnetic field were measured: 1) tangential to the main axis and 2)...
-
Behavior of residual current devices at earth fault currents with DC component
PublicationLow-voltage electrical installations are increasingly saturated with power electronic converters. Due to very high popularity of photovoltaic (PV) installations and the spread of electric vehicles (EV) as well as their charging installations, DC–AC and AC–DC converters are often found in power systems. The transformerless coupling of AC and DC systems via power electronic converters means that an electrical installation containing...
-
Recent developments in the determination of residual solvents in pharmaceutical products by microextraction methods
Publication -
The effect of earth fault current harmonics on tripping of residual current devices
PublicationSzerokie zastosowanie przekształtników, a w szczególności przemienników częstotliwości sprawia, że wyłączniki różnicowoprądowe znajdują się w obwodach, w których może płynąć odkształcony prąd ziemnozwarciowy. Prąd ziemnozwarciowy w obwodach z przemiennikami częstotliwości zawiera harmoniczne, których rząd głównie zależy od częstotliwości PWM. Odkształcony prąd wpływa na poprawne wyzwalanie wyłączników różnicowoprądowych. W artykule...
-
Evolution of post welded residual stress due multilayer circumferentialweld of tube.
PublicationOpisano sposób wykorzystania polowego efektu Barkhausena do pomiaru rozkładu naprężeń w spawanych rurach. Przedstawiono procedurę kalibracji oraz wyniki pomiaru naprężeń uzyskanych po stopniowym spawaniu rury.
-
Residual K1 and K2 Oscillations in Precise GPS Solutions: Case Study
Publication -
Requirements for Residual Current Devices Intended for Electric Vehicle Charging Systems
PublicationThe properties of residual current devices have been presented from the point of view of their ability to detect a specific shape of the residual current waveform. Moreover, the standard requirements relating to residual current protection used in electric vehicle charging installations have been pointed out. The operating characteristics of the IC-CPD and RDC-DD protections, which are intended for charging electric vehicles in...
-
Magnetic Resonance
Journals -
Influence of circuit breaker operation upon transformeros residual flux and inrush current
PublicationPrzedstawiono model i wyniki obliczeń prądu i strumienia magnetycznego w układzie zawierającym transformator trójfazowy i wyłącznik. Opracowano obwodowy model łącznika z łukiem elektrycznym. Model łuku zbudowano w oparciu o jego statyczną charakterystykę prądowo-napięciową z uwzględnieniem uproszczonej charakterystyki dynamicznej. Przeprowadzone symulacje wykazały, że wartość maksymalna prądu włączania transformatora zależy zarówno...
-
Fault loop impedance measurement in low voltage network with residual current devices
PublicationW sieciach i instalacjach niskiego napięcia z wyłącznikami różnicowoprądowymi pomiar impedancji pętli zwarciowej jest kłopotliwy. Prąd pomiarowy powoduje ich zbędne zadziałanie, co uniemożliwia prawidłowe wykonanie pomiaru. W artykule omówiono przyczyny zbędnego zadziałania wyłączników różnicowoprądowych podczas pomiaru impedancji pętli zwarciowej oraz warunki, w jakich ten pomiar można wykonać poprawnie.
-
Menopause: a trigger for simultaneous development of ulcerative colitis in sigmoid neovagina and residual colorectum?
Publication -
Identification of residual force in static load tests on instrumented screw displacement piles
PublicationOccurrence of the so-called residual force of an unknown value significantly disturbs interpretation of static load tests performed on piles equipped with additional measuring instruments. Screw displacement piles are the piling technology in which the residual force phenomenon is very common. Its formation mechanism is closely related to the installation method of this type of piles, which initiates generation of negative pile...
-
An investigation on residual stress and fatigue life assessment of T-shape welded joints
PublicationThis paper aims to quantitatively evaluate the residual stress and fatigue life of T-type welded joints with a multi-pass weld in different direction. The main research objectives of the experimental test were to test the residual stress by changing direction along with multiple wielding passes and determine the fatigue life of the welded joints. The result shows that compressive residual stress increases in the sample gradually...
-
Advanced numerical modelling for predicting residual compressive strength of corroded stiffened plates
PublicationAn advanced methodology for predicting the residual compressive strength of corroded stiffened plates is developed here using the non-linear finite element method. The non-uniform loss of a plate thickness is accounted for on a macro-scale. In contrast, mechanical properties are changed using the constitutive model to reflect the corrosion degradation impact on a micro-scale. Three different stiffened plate thicknesses are considered,...
-
Residual Effects of Different Cropping Systems on Physicochemical Properties and the Activity of Phosphatases of Soil
Publication -
Failure of cold-formed beam: How does residual stress affect stability?
PublicationIn machine industry, stresses are often calculated using simple linear FEM analysis. Occasional failures of elements designed in such a way require recomputation by means of more sophisticated methods, eg. including plasticity and non-linear effects. It usually leads to investigation of failure causes and improvement of an element in order to prevent its unwanted behavior in the future. The study presents the case where both linear...
-
Improving sensitivity of residual current transformers to high frequency earth fault currents
PublicationFor protection against electric shock in low voltage systems residual current devices are commonly used. However, their proper operation can be interfered when high frequency earth fault current occurs. Serious hazard of electrocution exists then. In order to detect such a current, it is necessary to modify parameters of residual current devices, especially the operating point of their current transformer. The authors proposed...
-
Numerical calculation of three-phase transformer's residual flux in ATP and PSpice programs.
PublicationW artykule przedstawiono analizę przebiegów prądu i strumienia magnetycznego podczas wyłączania transformatora energetycznego, wykonaną w celu określenia strumieni szczątkowych. Wykorzystano do tego celu modele obwodowe zbudowane w oparciu o programy symulacyjne ATP (Alternative Transients Program) i PSpice. Wyniki obliczeń okazały się bardzo zbliżone dla obu modeli. Przy ich wykorzystaniu obliczono strumienie szczątkowe w kolumnach...