Search
displaying 1000 best results Help
Search results for: ENDOTHELIAL LAYER
-
Few-Layer Black Phosphorus/Chitosan Nanocomposite Electrodes via Controlled Electrodeposition for Enhanced Electrochemical Kinetic Performance
PublicationThis study presents the preparation and characterization of few-layer black phosphorus (FLBP) chitosan electrodes by controlled electrochemical deposition of chitosan nanoparticles on FLBP-modified glassy carbon electrodes. FLBP was prepared by solvent-assisted exfoliation of bulk BP and was further modified with chitosan forming together a nanocomposite, including easy cross-linking with nanomaterials and film-forming properties....
-
An analytical four-layer horizontal electric current dipole model for analysing underwater electric potential in shallow seawater
PublicationThe paper presents a new analytical four‑layer (air–water–bottom–non‑conductive layer) horizontal electric dipole model which allows an accurate approximation of ship’s Underwater Electric Potential (UEP) from a sufficient depth in shallow coastal marine waters. The numerical methods, usually Finite Element Method (FEM) or Boundary Elements Method (BEM), are typically used to estimate the electric field and the distribution of...
-
Development of Safirinium dyes for new applications: fluorescent staining of bacteria, human kidney cells, and the horny layer of the epidermis
PublicationLow-molecular synthetic fluorophores are convenient tools in bioimaging applications. Several derivatives of Safirinium dyes as well as their reactive N-hydroxysuccinimide (NHS) esters bearing diverse substituents were synthesized and evaluated experimentally in terms of their lipophilicity by means of reverse-phase and immobilized artificial membrane high-performance liquid chromatography. Subsequently, the selected compounds...
-
Titania Nanotubes/Hydroxyapatite Nanocomposites Produced with the Use of the Atomic Layer Deposition Technique: Estimation of Bioactivity and Nanomechanical Properties
PublicationTitanium dioxide nanotubes/hydroxyapatite nanocomposites were produced on a titanium alloy (Ti6Al4V/TNT/HA) and studied as a biocompatible coating for an implant surface modification. As a novel approach for this type of nanocomposite fabrication, the atomic layer deposition (ALD) method with an extremely low number of cycles was used to enrich titania nanotubes (TNT) with a very thin hydroxyapatite coating. X-ray diffraction (XRD)...
-
Optimized conditions for hydrocarbon group type analysis of base oils by thin-layer chromatography - flame ionisation detection
PublicationW pracy przedstawiono wyniki badań nad opracowaniem optymalnych warunków oznaczania składu grupowego mineralnych olejów bazowych z wykorzystaniem chromatografii cienkowarstwowej oraz detektora płomieniowo-jonizacyjnego (TLC-FID). W przypadku mineralnych olejów bazowych, które otrzymywane są po wielu etapach rafinacji frakcji pochodzących z destylacji próżniowej ropy naftowej oznaczenie ich składu grupowego (z uwzględnieniem podgrup...
-
Electrochemical analysis of the passive layer cracking process on A95052 aluminium alloy performed by means of DC and AC techniques
PublicationPraca dotyczy porównania zastosowania technik stało- i zmiennoprądowych do badania pękania warstwy pasywnej na różnych stopach aluminum podczas testów rozciągania mechanicznego w warunkach polaryzacji anodowej.
-
Rozwój technologii nanokrystalizacji warstwy wierzchniej materiałów konstrukcyjnych = Development of nanocrystallization technologies of the surface layer of structural materials
PublicationPrzedstawiono szereg metod modyfikacji warstwy wierzchniej prowadzących do wytworzenia struktur nanokrystalicznych. Wskazano na zalety, wady i kierunki rozwoju poszczególnych metod
-
Thin layer headspace gas chromatography for biological monitoring of persons exposed to volatile organohalogen compounds from water
PublicationCelem pracy było zbadanie możliwości wykorzystania analizy fazy nadpowierzchniowej nad cienką warstwą cieczy z samoczynną generacją ciekłego sorbentu (TLHS)do izolacji i wzbogacania THM w próbkach moczu i krwi ludzkiej. Umożliwiło to następnie wykorzystanie prostej techniki bezpośredniego nastrzyku próbki do kolumny chromatografu gazowego, wyposażonego w detektor wychwytu elektronów (DAI-GC-ECD).Przy pomocy tak opracowanej metody...
-
Novel approaches in the synthesis of batracylin and its analogs: rebirth of an old player?
PublicationW pracy opisano batracylinę (BAT), jej syntezę i aktywność biologiczną oraz otrzymane analogi. BAT została wyselekcjonowana przez NCI (Bethesda, USA) w programie poszukiwań nowych potencjalnych leków przeciwnowotworowych. Związek ten w badaniach in vivo na myszach okazał się bardzo aktywny przeciw nowotworowi okrężnicy 38 (Colon 38), trudnemu do wyleczenia przez dotychczas znane leki przeciwnowotworowe. Jest ona skuteczna również...
-
Evaluation of Thermal Stresses in Asphalt Layers in Comparison with TSRST Test Results
PublicationThe paper presents the results of calculations and laboratory determination of thermal stresses at low temperatures. The modified Hills and Brien's method was used to calculate the thermal stresses in asphalt layers of pavements and the results were compared against the values obtained at a laboratory with the Thermal Stress Restrained Specimen Test (TSRST) method. The laboratory investigations were conducted using plain grade...
-
Interface layers between electrolyte and cathodes for solid oxide fuel cells
PublicationW pracy przebadano możliwość zastosowania warstwy CGO ((CeO2)0.8 (Gd2O3)0.1) w tlenkowych ogniwach paliwowych. Do wytworzenia warstwy użyto pirolizy aerozolowej.
-
Oxide layers fabricated by spray pyrolysis for resistance random access memory
PublicationW pracy zbadano przydatność pirolizy aerozolowej do wytwarzania warstw dla memrystorów.
-
Seeding enhancement for microcrystaline diamond layers growth on non-diamond substrates
PublicationThe present paper gives an overview on the possible methods of seeding substrates for diamond layers growth. Diamond in reason of his properties is very desirable material in microelectronic, biomedical and waste treatment sensors. Microcrystalline diamond for these applications must be grown on silicon substrate in microwave plasma assisted chemical vapor deposition (MPACVD). To grow diamond on non-diamond surface pre-growth...
-
Adjusting Game Difficulty by Recreating Behavioral Trees of Human Player Actions
PublicationThis paper presents a proposition of a method for adjusting game difficulty to the current level of player's skills in one-on-one games. The method is based on recognition of human player's actions and recording of those actions in the form of behavioral trees. Such trees are later used to drive behaviors of computer-controlled opponents so that human player has beat hit own strategy and improve on it, to win subsequent games....
-
Effects of the preheating laser treatment on microstructure and corrosion resistance of Ti6Al4V bioalloy
PublicationThe laser remelting of the Ti6Al4V alloy was made on specimens pre-heated at elevated temperatures. The laser treatment effected in change of microstructures of surface layers and an appearance of blisters and numerous cracks. The corrosion tests demonstrated the decrease in corrosion resistance for each preheating temperature. The observed effects were attributed to negative influence of excessive compressive stresses with no...
-
Influence of nitrogen plasma treatment on the wettability of polyetheretherketone and deposited chitosan layers
Publication -
Properties of surface layers of duplex stainless steel after burnishing processes
PublicationStress corrosion cracking resistance of cold worked layers of 25 Cr duplex stainless steel grade UR52N+ has been investigated. The surface layers were performed through burnishing treatment. The residual stresses at surface layers were determined using grazing angle incidence X-ray diffraction method (g-sin2 Ψ). Corrosion tests were performed with the use of Slow Strain Rate Test technique in boiling 35% MgCl2 solution. It has...
-
Thermal Stability of Multicomponent Layers Created with the Hybrid Method on Aluminium Base
PublicationW pracy przedstawiono skład fazowy, mikrostrukturę oraz graficzny i matematyczny opis kinetyki utleniania wieloskładnikowych warstw powierzchniowych wytworzonych na aluminiowym podłożu.
-
Cavitation wearing of the SUPERSTON alloy after laser treatment at cryogenic conditions
PublicationThe purpose of this paper is to demonstrate the method of laser remelting at cryogenic conditions of the SUPERSTON alloy and its influence on microstructure and cavitation wearing. The cavitation test was performed using the rotating disc facility in IPM PAN Gdansk. During the cavitation test, the mass loss of the material with different parameters of laser remelting was determined. Surface and cross-section microstructure of the...
-
Study of structures and properties of the laser cladding exhaust valve after service
PublicationPrzylgnie zaworów wydechowych silnie obciążonego silnika okrętowego zostały pokryte warstwą wykonana ze stopu kobaltu za pomocą techniki napawania laserowego. Tak przygotowane zawory były eksploatowane przez 3000 godzin w silniku Daru Młodzieży. Po tym czasie zostały zdemontowane i poddane szczegółowej analizie. Warunki pracy spowodowały powstanie na powierzchni przylgni warstwy tlenków o różnej grubości, wykazującej skłonność...
-
Nanotubular Titanium Oxide Layers for Enhancement of Bone-Implant Bonding and Bioactivity
PublicationThe present paper describes the techniques to improve the bioactivity of titanium and enhance the bone-implant bonding ability by the electrochemical anodization to fabricate titania nanotube arrays (TiO2).
-
Nanotubular Ti Oxide Layers for Enhancement of Bone-Implant Bonding and Bioactivity
PublicationAbstrakt artykułu pt. ''Nanotubular Ti Oxide Layers for Enhancement of Bone-Implant Bonding and Bioactivity''. The paper describes techniques to improve the bioactivity of titanium and ehnahnce the bone-implant bonding ability by the electrochemical anodization to fabricate titania nanotubular oxide layer.
-
ELECTROCHEMOTHERAPY COMBINED WITH STANDARD AND CO2 LASER SURGERIES IN CANINE ORAL MELANOMA
Publication -
Determination of grain shape of laser-irradiated FePdCu thin alloy films
Publication -
Effect of concentration boundary layers on mechanical pressure in a double-membrane system
Publication -
Computer-aided design and selective laser melting of porous biomimetic materials
Publication -
Porous Selective Laser Melted Ti and Ti6Al4V Materials for Medical Applications
Publication -
Multiaxial fatigue behaviour of maraging steel produced by selective laser melting
Publication -
Evaluation of Thermal Stresses in Asphalt Layers Incomparison with TSRST Test Results
Publication -
ADCP Observations of Diel Vertical Migration of Biological Layers in Gulf of Gdańsk
Publication -
Evaluation of laser texturing in fabricating cut-resistant surfaces for protective gloves
Publication -
Nd3+ doped titanate-germanate glasses for near-IR laser applications
Publication -
Creation and characteristics of the (Mn-N-O) surface layers on aluminium alloy
PublicationPrzedstawiono koncepcję tworzenia warstw powierzchniowych zawierających mangan, azot i tlen. Warstwy wykazują twardość powierzchniową 358 HV0,01, zwiększoną odporność na korozję w kwasie siarkowym oraz odporność na zużycie ścierne w skojarzeniu z żeliwem szarym.
-
Operation of a free-electron laser from the extreme ultraviolet to the water window
Publication -
European X-Ray Free Electron Laser (EXFEL): local implications
Publication -
Comparison of Vacuum Sintered and Selective Laser Melted Steel AISI 316L
Publication -
Laser Surface Alloying of Aluminium Alloys with Cu/Fe Metallic Powders
Publication -
Laser Surface Treatment of Sintered Stainless Steels for Wear Resistance Enhancement
Publication -
Acousto-optic interaction with the use of cylindrical ultrasonic waves in the laser cavity
Publication -
Patterned hydrophobic and hydrophilic surfaces of ultra-smooth nanocrystalline diamond layers
Publication -
Deposition, morphology and functional properties of layers based on DLC:Si and DLC:N on polyurethane
Publication -
Nanotubular oxide layers and hydroxyapatite coatings on ‘Ti–13Zr–13Nb’ alloy
PublicationThe presented research was aimed to determine the mechanical properties of the nanotubular oxide layer covered with hydroxyapatite coating. The Ti–13Zr–13Nb alloy was oxidised in 1M phosphoric acid with an addition of 0?5% HF for HF solution at 20 V voltage. The electrochemically assisted deposition of hydroxyapatite was performed at cyclic polarisation in NH4H2PO4 and CaCl2 solution at 80uC. The mechanical properties were determined...
-
Analysis of the applicability of laser scanning to making an inventory of swimming pool facilities
Publication3D scanning can be used in many branches of economy, e.g. reverse and prototype engineering, industrial design, quality control, pros-thetics, orthodontics, archiving of historic objects and archeological findings, examination of a scene of crime, making films and comput-er games. The technology of terrestrial laser scanning has a bright fu-ture as we are living in the time of blooming measurement tech-niques, which can provide...
-
THE POSSIBILITY OF USE OF LASER-MODIFIED Ti6Al4V ALLOY IN FRICTION PAIRS IN ENDOPROSTHESES
PublicationThe purpose of this paper is to show results of laser treatment at cryogenic conditions of the Ti6Al4V alloy used for orthopedic applications. That modification process ought to bring beneficial changes of microstructure and residual stresses in the surface layer. The paper presents the abrasive wear of the base and laser remelted material in association with ceramics Al2O3. Despite the surface cracking after laser treatment the...
-
Micropatterning of BiVO 4 Thin Films Using Laser-Induced Crystallization
PublicationRelatively high temperatures even up to 500 °C are required to obtain bismuth vanadate (BiVO4) films with the scheelite monoclinic (s-m) structure that shows the highest photocatalytic activity. This requirement limits the possible choice of substrates. Moreover, high quality thin layers of crystalline BiVO4 cannot be prepared with current methods. In this study a light-induced crystallization approach is presented, which is a...
-
Laser patterned platform with PEDOT–graphene composite film for NO2 sensing
PublicationThis work presents a simple and fully electrochemical route used for fabricating of a NO2 gas sensor made of reduced-graphene-oxide-poly(3,4-ethylenedioxythiophene) composite film. The sensing platform was fabricated from alumina substrate and equipped with gold interdigitated electrodes and built-in heater.The temperature distribution on the surface of interdigitated electrodes was investigated by a thermalimaging camera and compared...
-
Airborne and mobile laser scanning in measurements of sea cliffs on the southern Baltic
PublicationMeasurements of sea cliffs performed using periodic surveying based on laser scanning is currently one of the fastest and most accurate solutions. Supported with the technology of satellite measurements using GNSS (Global Navigation Satellite System) positioning and photographic measurements with the use of aerial vehicle, they enable an effective monitoring of the sea cliffs affected by the erosion. In case of the coast of southern...
-
Optical and photoelectrochemical characterization of pulsed laser deposited Bi4V2O11, BICUVOX, and BIZNVOX
PublicationThin layers of three compounds from the BIMEVOX family (Bi4V2O11, Bi2V0.9Cu0.1O5.35, and Bi2V0.9Zn0.1O5.35) were prepared via pulsed laser deposition technique on quartz, silicon, and platinum foil and tested as photoanodes for water photooxidation. The film formation, as well as the crystallization upon heating, was characterized using X-ray diffraction and Raman spectroscopy. The optical properties were investigated using spectroscopic...
-
Metal Oxides and Low Temperature SWCNT Synthesis via Laser Evaporation
Publication -
Coastal Cliffs Monitoring and Prediction of Displacements Using Terrestial Laser Scanning
PublicationCoastal cliffs are very sensitive to degradation caused by erosion and abrasion. Thus, it is very important to monitor susceptibility of the cliffs in terms of slope angles and ground fall resulting from vertical morphology of the cliffs. The results could be used for example to establish the boundaries of the safe investments zone or retreat infrastructure buildings in case of real threat such as degradation of the objects of...