Search
Filters
total: 6935
-
Catalog
displaying 1000 best results Help
Search results for: MILLIMETER WAVE
-
Verification of algorithms determining wave loads on support structure of wind turbine
PublicationThe offshore wind turbines require determination of wave loads on their support structure. This structure is fixed and, therefore, this problem is reduced to solving only the diffraction problem, which is determined by Laplace equation and conditions on the following boundaries: on the support structure, on the sea free surface and on its bottom, and at infinity on free surface. The linear problem was applied to determine the wave...
-
Impact of radio wave polarisation on off-body communications in indoor environments
PublicationThis paper describes the measurements and the analysis of the impact of radio wave polarisation on off-body communications in Body Area Networks in indoor environments. Measurements on polarisation impact are briefly described. Five investigated scenarios with different body postures and different antenna placements are characterised. The difference between the vertical and horizontal components of the received radio signal are...
-
Ground anchors diagnostic process based on elastic wave propagation method
PublicationThe paper is focused on analysis of elastic wave propagation in the context of diagnostics of ground anchors. Numerical simulations were performed to assess the possibility of evaluation of the anchorage quality. It was assumed that the quality and the load capacity of the anchor system directly depend on the length, on which mortar and steel cooperate.
-
A higher order shell element for wave propagation in isotropic shell structures
PublicationThe presents the new multi mode higher order shell element for wave propagation problems in shell structures.
-
Sensorless induction motor drive with voltage inverter and sine-wave filter
PublicationThis paper presents a speed sensorless control system of an induction motor with an output LC filter. It is known that the parameters design of the filter gives sine wave motor supply voltage but complicates control and estimation process. The reason is that the voltage drop and phase shift between filter input and output signals are imposed, and hence the motor voltages and currents differ from the inverter output waveforms. To...
-
Rectangular microstrip resonator illumi-nated by normal-incident plane wave
PublicationW pracy przedstawiono koncepcję modów oświetlających pozwalającą na obliczenie podstawowych parametrów elektrycznych anten mikropaskowych - częstotliwości rezonansowej, rezystancji promieniowania i charakterystyki promieniowania. Oparta jest ona na dwuwymiarowej metodzie przestrzeni widmowej, w której pobudzenie występuje w formie pojedynczej fali płaskiej padającej prostopadle na analizowaną strukturę. Rezultatem takiego podejścia...
-
Electromagnetic wave scattering from material objects using hybrid methods
PublicationRozdział zawiera opis hybrydowych metod analizy stanowiących połączenie metody różnic skończonych w dziedzinie częstotliwości (FDFD) z metodą dopasowania rodzajów (MM), służących do badania cylindrycznych struktur falowych w układach zamkniętych i otwartych.
-
Testing the impact of simplifications adopted in models describing wave loads on ship
PublicationThe wave-ship system in naval architecture is generally assumed to be a linear one. This allows for the computation of a transfer function of ship response to waves including wave loads on ship. The transfer function and the wave spectral density function enable the development of the stochastic process of wave loads on ship, corresponding to the irregular wave generating that loads. If the mathematical models of wave load transfer...
-
Testing the impact of simplifications adopted in models describing wave loads on ship
PublicationThe wave-ship system in naval architecture is generally assumed to be a linear one. This allows for the computation of a transfer function of ship response to waves including wave loads on ship. The transfer function and the wave spectral density function enable the development of the stochastic process of wave loads on ship, corresponding to the irregular wave generating that loads. If the mathematical models of wave load transfer...
-
Non-Wave Variations in Temperature Caused by Sound in a Chemically Reacting Gas
PublicationA weakly nonlinear generation of non-acoustic modes in the field of sound in a gas is considered. An exotericchemical reaction of A->B type, which takes place in a gas, may be reversible or not. Two types of sound areconsidered, low-frequency and high-frequency as compared with the characteristic time of a chemical reaction.For both these cases, the governing equations of non-acoustic modes are derived and conclusions of the efficiencyof...
-
On some properties of 2d spectral finite elements in problems of wave propagation
PublicationW pracy przedstawiono sformułowanie dwuwymiarowych elementów spektralnych stosowanych w symulacji propagacji fal prowadzonych. Zbadano własności tych elementów pod kątem występowania form pasożytniczych, odporności na dystorsję siatki oraz zbadano wpływ kształtu elementu na krzywe dyspersji
-
System setup and software for cyclic, staircase and square wave voltammetry measurements
PublicationHardware dedicated for electrochemical measurement sometimes does not allow performing certain voltammetry experiments. Staircase and square wave voltammetry, techniques which have many advantages comparing with standard voltammetric techniques, are rarely implemented in software controlling electrochemical measuring equipment. These methods, however, can be relatively easy realized with some addition...
-
Design solution and selected research results of the sea-wave energy converter
PublicationW artykule przedstawiono oryginalne rozwiązanie konstrukcyjne boi do pozyskiwania energii fal morskich oraz analizy i badania modelowe turbiny wodnej poprzedzające wybór ostateczny konstrukcji modelu boi w skali 1:5 przewidzianego do badań eksperymentalnych w basenie holowniczym. Zaprezentowano także wybrane wyniki badań modelowych i symulacji komputerowych ukazujący wpływ systemu kotwiczenia i innych parametrów na jakość i efektywność...
-
Modeling of the finite amplitude plane wave propagation in non-dissipative medium
PublicationPraca prezentuje wyniki analizy teoretycznej zagadnienia propagacji fali płaskiej o skończonej amplitudzie w ośrodku wodnym bez dyssypacji. Przedstawiono model matematyczny i przykładowe wyniki obliczeń numerycznych. Model matematyczny zbudowano w oparciu o jednowymiarowe równania mechaniki płynów. Do rozwiązania zagadnienia zastosowano metodę różnic skończonych. Analizowano zmiany ciśnienia i zmiany widma. Badano zbieżność i dokładność...
-
Extreme bottom velocities induced by wind wave and currents in the Gulf of Gdańsk
Publication -
MEDIUM-TERM WAVE AND CURRENT MODELLING FOR A MESOTIDAL WADDEN SEA COAST
Publication -
Wind wave climate of west Spitsbergen: seasonal variability and extreme events
Publication -
Wave-induced bedload transport – a study of the southern Baltic coastal zone
Publication -
The expansion wave of an invasive predator leaves declining waterbird populations behind
Publication -
Elastic wave propagation for condition assessment of steel bar embedded in mortar
PublicationThis study deals with experimental and numerical investigations of elastic wave propagation in steel bars partially embedded in mortar. The bars with different bonding lengths were tested. Two types of damage were considered: damage of the steel bar and damage of the mortar. Longitudinal waves were excited by a piezoelectric actuator and a vibrometer was used to non-contact measurements of velocity signals. Numerical calculations...
-
Giant Nernst effect in the incommensurate charge density wave state of P4W12O44
PublicationWe report the study of Nernst effect in quasi-low-dimensional tungsten bronze P4W12O44 showing a sequence of Peierls instabilities. We demonstrate that both condensation of the electronic carriers in the charge density wave state and the existence of high-mobility electrons and holes originating from the small pockets remaining in the incompletely nested Fermi surface give rise to a Nernst effect of a magnitude similar to that...
-
Non-destructive inspection of ground anchors using guided wave propagation
PublicationThis paper deals with numerical and experimental investigations of specific problems of guided wave propagation in ground anchors. The research focuses on recognizing the phenomenon of the energy transfer between anchor components. Particular attention is paid to characteristic features of guided waves propagating in free and embedded parts of the tendon, at the interface between the tendon and the surrounding anchor body as well...
-
Coherent-wave Monte Carlo method for simulating light propagation in tissue
PublicationSimulating propagation and scattering of coherent light in turbid media, such as biological tissues, is a complex problem. Numerical methods for solving Helmholtz or wave equation (e.g. finite-difference or finite-element methods) require large amount of computer memory and long computation time. This makes them impractical for simulating laser beam propagation into deep layers of tissue. Other group of methods, based on radiative...
-
Elastic wave propapagation in diagnostics of self-drilling system of grouted anchors
PublicationThe paper presents an experimental investigation of elastic wave propagation in a self-drilling hollow bar system, which is commonly used in geotechnical industry as the element of grouted ground anchors and soil nails. The single self-drilling hollow bar and self-drilling system of two bars connected by a coupler were considered. Longitudinal waves were excited at one end of the bar and registered at both ends, by means of PZT...
-
Fast Full-Wave Multilevel Zero-Pole Optimization of Microwave Filters
PublicationA new concept is proposed for the full-wave computer-aided design of microwave filters. The method consists of two stages and operates on the zeros and poles of the transfer function and their derivatives. These quantities are evaluated from the response computed by a full-wave electromagnetic solver with two levels of accuracy. The two stages make use of different models that are optimized using a low-accuracy electromagnetic...
-
An Experimental Investigation of Pressure Wave Celerity During the Transient Slurry Flow
PublicationTransportation of slurries in pressure pipelines is an example of a complex flow due to specific parameters of transported medium. For practitioners, the economy of designing and maintenance is usually the most important factor. For this reason, most of hydrotransport installations are fairly simple; however, they become more vulnerable to negative effects of the transient flow which can occur in pressure pipelines. As the consequence,...
-
Lamb wave-based monitoring of shear failure of an adhesive lap joint
PublicationThe paper presents a study on the elastic wave propagation in adhesive joints of steel plates subjected to tensile loading. A single lap joint was chosen for analysis because of its simplicity and plurality of applications. Experimental investigations consisted of the uniaxial extension of prepared specimens. Force and displacement values were recorded by a testing machine. Simultaneously, guided Lamb waves were excited and signals...
-
Numerical investigation of the core eccentricity effect on wave propagation in embedded waveguide
PublicationThe paper presents results of theoretical and numerical investigation of guided wave propagation in two-layer bars with geometric imperfections in the form of eccentric location of steel core. Steel rod of diameter equal to 1 cm embedded in composite mortar-type cover with external diameter equal to 5 cm has been taken into consideration. Several different rods with variable size of eccentricity are analysed. Results for rods with...
-
Debonding Detection in Reinforced Concrete Beams with the Use of Guided Wave Propagation
PublicationOne of the most frequent damage of the reinforced concrete structures is debonding between steel bar and concrete cover. In the case of debonding occurrence not only the strength of the structure decreases, but also it is more vulnerable to corrosion damages. For this reason fast and effective methods of debonding detection in an early stage of its development need a significant boost. The paper presents analytical and experimental...
-
Guided Wave Propagation in Detection of Partial Circumferential Debonding in Concrete Structures
PublicationThe following article presents results of investigating the damage detection in reinforced concrete beams with artificially introduced debonding between the rod and cover, using a non-destructive method based on elastic waves propagation. The primary aim of the research was to analyze the possible use of guided waves in partial circumferential debonding detection. Guided waves were excited and registered in reinforced concrete...
-
Research on assessment of bolted joint state using elastic wave propagation
PublicationThe work contains results of experimental investigation of elastic wave propagation in a bolted single-lap joint. Tests were carried out for the excitation perpendicular to the connection plane. In experimental studies, PZT transducers were used for both excitation and registration of ultrasonic waves. The analyses took into account varying contact conditions between the elements of the connection depending on the value of the...
-
Radiation phenomena from metamaterial cylinders at oblique plane wave incidence.
PublicationW pracy przedstawiono wpływ ujemnej przenikalności elektrycznej i magnetycznej rezonatorów cylindrycznych umieszczonych w wolnej przestrzeni na parametry rozproszenia. Wykorzystano zmodyfikowaną procedurę iteracyjną i metodę dopasowania rodzajów w celu badania fali rozproszonej od układu cylindrów przy ukośnym padaniu fali płaskiej.
-
Elastic wave propagation in frame structure in the context of structural health monitoring
PublicationPraca dotyczy propagacji fal sprężystych r konstrukcji ramowej w ośrodku typu belka Timoszenki. Do obliczeń numerycznych wykorzystano wielowęzłowe spektralne elementy skończone klasy C0. Omówiono algorytm całkowania po czasie i sformułowano wnioski dotyczące liczby węzłów na długość fali.
-
Basic ideas and advantages of the method of analytical regularization in wave optics: Overview
Publication -
Analysis of longitudinal wave propagation in a cracked rod by the spectral element method
Publication -
On the design of planar high directivity proximity couplers in the mm-wave range
PublicationPrzedyskutowano problemy projektowania sprzęgaczy zbliżeniowych wykonywanych w technologii planarnej i przeznaczonych do pracy w zakresie fal milimetrowych. Zasadniczym celem badań było zaprojektowanie, wykonanie i przebadanie układu sprzęgacza o wysokiej kierunkowości i umiarkowanym poziomie sprzężenia pracującego w zakresie 40-50GHz. Przedyskutowano i zamodelowano różne konfiguracje sprzęgaczy. Stwierdzono, że znane zasady projektowania...
-
Wave propagation modelling in 1D structures using spectral finite elements
PublicationW artykule omówiono modele propagacji fal wzdłużnych i poprzecznych w prętach oparte na dwóch sformułowaniach (w dziedzinie częstości i w dziedzinie czasu) metody elemntów spektralnych. Porównano otrzymane wyniki z wynikami eksperymentu.
-
Lamb Wave Based Structural Damage Detection Using Stationarity Tests
Publication -
Identification of discontinuites in composite rods and beams based on Lamb wave propagation
PublicationW pracy omówiono metodę identyfikacji typu nieciągłości w belkach i prętach kompozytowych, oparta o analizę zmain w propagacji fali Lamba.
-
Experimental an numerical investigation of wave propagation in composite beam with an additional mass
PublicationW pracy przedstawiono wyniki badań eksperymentalnych i symulacji numerycznych ilustrujace wpływ dodatkowej masy na propagacje fali Lamba w belce kompozytowej.
-
Guided wave propagation for assessment of adhesive bonding between steel and concrete
PublicationAdhesive bonding is becoming more increasingly important in joining of structural elements. In civil engineering, there is a growing interest in connection by adhesive bonding in steel-concrete flexural members. This study concerns the guided wave propagation technique applied to condition assessment of an adhesive connection between a steel member and a concrete beam. Various states of degradation were considered by producing...
-
A novel formulation of 3D spectral element for wave propagation in reinforced concrete
PublicationThe paper deals with numerical simulations of wave propagation in reinforced concrete for damage detection purposes. A novel formulation of a 3D spectral element was proposed. The reinforcement modelled as the truss spectral element was embedded in the 3D solid spectral finite element. Numerical simulations have been conducted on cuboid concrete specimens reinforced with two steel bars. Different degradation models were considered...
-
Design and Evaluation of the Compact and Autonomous Energy Subsystem of a Wave Energy Converter
PublicationThis paper presents the results of the design process focused on the development of the energy subsystem (ES) of a wave energy converter (WEC). The ES is an important electrical part that significantly affects the energy reliability and energy efficiency of the entire WEC device. The designed ES was intended for compact WECs powering IoT network devices working in the distributed grid. The developed ES is an electronic circuit...
-
Detection and size estimation of crack in plate based on guided wave propagation
PublicationThe paper presents results of the comprehensive theoretical and experimental investigation of crack detection in metallic plate using guided wave propagation. The main aim of the paper is to develop the novel method which would allow for linear crack size estimation with the use of minimal number of the transducers. In general, there exists the relation between length of the propagation path and the wave amplitude value. However,...
-
Application of the ISE Optimized Proportional Control of the Wave Maker in a Towing Tank
PublicationThis paper presents the improvement of the wave maker control system. The wave maker is a facility widely used in hydromechanics laboratories to generate waves in towing tanks. It is equipped with an electrohydraulic drive and an actuator submerged into water. The waves are generated to model the environmental conditions for physical experiments, performed on reduced-scale models of maritime objects. The physical experiments allow...
-
Electromagnetic wave scattering by a set of axially symmetric omega-medium cylinder
PublicationZaprezentowano analizę rozproszenia fali elektromagnetycznej od układu obiektów cylindrycznych zbudowanych z materiałów pseudochiralnych, umieszczonych w złączach falowodowych lub wolnej przestrzeni. Analiza bazuje na iteracyjnej procedurze rozproszenia i metodzie dopasowania rodzajów.
-
Mind the Gender Wage Gap – the Impact of Trade and Competition on Sectoral Wage Difference
PublicationThis article examines differences between women’s and men’s wages in 18 selected OECD countries in the period 1970-2005. The study is based on 12 manufacturing sector- and skill-specific sets of panel data on the gender wage gap. We apply a system GMM estimator to the extended version of the conditional gender wage gap convergence equation, controlling for sector concentration and industry-specific measures of openness using a...
-
Ultrafast Intramolecular Relaxation and Wave-Packet Motion in a Ruthenium-Based Supramolecular Photocatalyst
PublicationThe hydrogen-evolving photocatalyst [(tbbpy)2 Ru(tpphz)Pd(Cl)2 ](2+) (tbbpy=4,4'-di-tert-butyl-2,2'-bipyridine, tpphz=tetrapyrido[3,2-a:2',3'-c:3'',2''-h:2''',3'''-j]phenazine) shows excitation-wavelength-dependent catalytic activity, which has been correlated to the localization of the initial excitation within the coordination sphere. In this contribution the excitation-wavelength dependence of the early excited-state relaxation...
-
Guided wave propagation in structures. Modelling, experimental studies and application to damage detection
PublicationCelem niniejszej pracy są eksperymentalne i numeryczne analizy propagacji prowadzonych fal sprężystych w stalowych konstrukcjach prętowych, belkowych, ramowych, tarczowych i płytowych. W szczególności praca poświęcona jest: (a) modelowaniu propagacji fal z uwzględnieniem zjawiska dyspersji; (b) budowie modeli obliczeniowych w formalizmie metody elementów spektralnych; (c) eksperymentalnej weryfikacji zaproponowanych modeli; (d)...
-
Slow-wave resonant structures in branch-line coupler miniaturization: a case study
PublicationA case study of novel slow-wave resonant structures dedicated to efficient microstrip branch-line coupler size reduction has been presented. A compact 3-dB branch-line coupler has been designed to mimic the performance of its conventional counterpart, simultaneously demonstrating a substantial 88% surface area reduction. The vital usefulness of the approach in the process of microstrip line abbreviation has been experimentally...