Publications
Filters
total: 484
Catalog Publications
Year 2016
-
ELEMENTY OPISU MIEJSCA WYPADKU DROGOWEGO
PublicationW celu dokonania rekonstrukcji wypadku drogowego niezbędny jest szczegółowy oraz oddający w pełni stan rzeczywisty opis miejsca wypadku. Poniższy artykuł omawia podstawowe elementy takie jak protokół miejsca wypadku, szkic, dokumentacje fotograficzną oraz ocenę obrażeń uczestników wypadku.
-
Effect of plasma sprayed and laser re-melted Al2O3 coatings on hardness and wear properties of stainless steel
PublicationCommercially available austenic stainless steel substrate was coated with commercially available, raw Al2O3 powder applied by means of plasma spraying method and then re-melted with CO2 laser beam of various parameters. Tribological and mechanical properties of the 120 J/mm and 160 J/mm laser re-melted coatings were compared with the tribological and mechanical properties of the “as-sprayed” coating. The influence of the laser...
-
DESIGN AND CALIBRATION OF ROLLING RESISTANCE TEST TRAILER R2mk.2
PublicationThe paper describes construction nad calibration procedures of the rolling resistance test trailer R2 Mk2. The trailer is design to measure rolling resistance of passenger car tyres in various road conditions on trafficked road. The trailer utilizes so called angle method also known as vertical arm method. The paper presents also calibration procedures that are necessary to ascertain good precision of the measurements.
-
AUTOBUSY NAPĘDZANE CNG W POLSCE
PublicationW artykule omówiono wykorzystanie sprężonego gazu ziemnego CNG, jako paliwa napędzającego autobusy komunikacji miejskiej w Polsce. Zarówno w latach ubiegłych jak i teraz paliwo to nie jest popularne w naszym kraju głównie ze względu na duże koszty wstępne w postaci infrastruktury (stacji tankowania, warsztatów napraw) oraz samej instalacji w pojeździe. CNG stosuje się głównie we flotach pojazdów wykonujących duże przebiegi roczne...
-
ANALYSIS OF THE POSSIBILITIES OF HIGH SPEED SHAFT BEARING SYSTEM DURABILITY INCREASE
PublicationDuring the operation of wind turbines with a gearbox of traditional configuration, a high failure rate of high-speed shaft bearings is observed. Such a high failures frequency is not reflected in standard bearing durability calculation methods, which can be attributed to atypical failure mechanism. To avoid observed problems in the 1.5 MW wind turbine, the modification of the existing bearing system is proposed. Multiple options,...
-
Analysis of Ceramic Elements with Ring-Crack Defects in Lubricated Rolling Contact
PublicationThe properties of ceramics, specifically low density, high hardness, high temperature capability and low coefficient of thermal expansion are of most interest to rolling element manufacturers. Surface ring cracks on lubricating rolling contact fatigue failure has been studied using numerical fracture analysis. Such cracks are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculations...
-
Analiza porównawcza zmierzonych wartości opóźnienia hamowania samochodu osobowego ze sprawnym i uszkodzonym układem hamulcowym
PublicationPrzeprowadzono szereg prób ekstremalnego hamowania samochodu osobowego ze sprawnym i uszkodzonym układem hamulcowym oraz z działającym i niedziałającym układem ABS. Próby przeprowadzono przy prostoliniowym torze jazdy na płycie poślizgowej Autodromu Pomorze. W artykule przedstawiono wyniki osiągniętych wartości średniego, pełnego opóźnienia hamowania.
-
Analiza oporu toczenia kół jezdnych samochodu podczas jazdy po różnych nawierzchniach drogowych
PublicationW pracy została podjęta problematyka zmiany oporu toczenia kół jezdnych samochodu w zależności od typu nawierzchni drogowej. Przeprowadzono badania eksperymentalne samochodu ciężarowego podczas jazdy po różnych nawierzchniach drogowych. Podczas badań wyznaczono charakterystyki wybiegu pojazdu. Na podstawie utworzonych charakterystyk wybiegu wyznaczono długości drogi wybiegu oraz uśrednione wartości współczynnika oporu toczenia...
-
AN ATTEMPT AT IDENTIFYING THE INFLUENCE OF TEST HEAD ASSEMBLY STIFFNESS ON THE RESULTS OF A TRIBOLOGICAL EXPERIMENT CONDUCTED UNDER MICRO-OSCILLATION CONDITIONS
PublicationThe outcome of experimental research on a group of dry bearing materials carried out under small oscillation conditi ons and using a test rig designed and made at Gdansk University of Technology inspired the decision to find out if the stiffness of test head elements in fluenced the generated results. Therefore, a computer model utilising finite elements was devised and used to simulate the workings of the test head. The mode l...
-
Acoustic journal bearing – Performance under various load and speed conditions speed conditions
PublicationThe paper presents results of experimental testing aiming at finding out what effect system of piezo-electric actuators (PZTs)attached to an aerodynamic journal bearing has on the magnitude of shaft's motion within the bearing operating at specified speed and load. The results clearly demonstrate effectiveness of PZTs in mitigating the shaft's motion thus contributing to the increased stability of the bearing. This stabilizing...
-
A Conception of Pairwise Comparisons Model for Selection of Appropriate Body Surface Area Calculation Formula
PublicationBody surface area (BSA) may be computed using a variety of formulas, but the computed BSA differs from real BSA values for particular subjects. This is presented in the paper by computing BSA values for selected subject and comparing them to the real BSA value obtained with the use of a 3D body scanner. The results show inequalities in the relevant BSA computing formulas. Hence, there is a need to determine a method that will allow...
Year 2017
-
Wyznaczanie prędkości opadania złoża biomasy metodą fluorescencji rentgenowskiej
PublicationPromieniowanie jonizujące używane jest powszechnie w przemyśle do uzyskania obrazu radiograficznego. Głównym zastosowaniem przemysłowym badań radiograficznych (RT) są badania nieniszczące (NDT) stosowane głównie do wykrywania nieciągłości wykonawczych i eksploatacyjnych w elementach metalowych oraz badania spoin. Duże zastosowanie badań radiograficznych znajduje się także w analityce chemicznej. Badania opadania złoża w reaktorze...
-
Wpływ wybranych właściwości maszyny badawczej na wynik eksperymentu tribologicznego z tarciem ślizgowym
PublicationNiniejsza monografia stanowi podsumowanie przekrojowych badań związanych z wpływem właściwości stanowiska badawczego (tribometru) na przebieg i rejestrowane wyniki eksperymentu tribologicznego z tarciem ślizgowym ciał stałych smarowanych cieczą w warunkach tarcia bez efektów smarowania hydrodynamicznego. Autor przedstawia wyniki kompleksowych analiz właściwości dynamicznych stanowiska badawczego w kontekście efektów obserwowanych...
-
Wpływ kierowcy na opór toczenia samochodu
PublicationW pracy omówiono wpływ zachowań kierowcy na opory toczenia pojazdu w ruchu drogowym. Można tu wyróżnić styl jazdy kierowcy oraz jego dbałość o pojazd. Przedstawiono wzrost oporu toczenia w aspekcie dynamicznego przyspieszania oraz szybkiej jazdy na zakręcie. Przeanalizowano także wpływ na opór toczenia takich czynników jak: ciśnienie w ogumieniu obciążenie promieniowe, zbieżność kół jezdnych samochodu oraz zużycie ogumienia.
-
Wpływ implantacji jonowej na wybrane właściwości użytkowe stopu Ti-13Nb-13Zr w aspekcie zastosowania na elementy trące w endoprotezach stawu biodrowego
PublicationOgraniczeniem stosowania stopów tytanu na implanty długookresowe, które podlegają obciążeniom zmiennym jest, oprócz zjawiska metalozy, ich stosunkowo niska odporność na zużycie poprzez tarcie. Zachodzące procesy zużycia tribologicznego na powierzchniach współpracujących elementów pary trącej ograniczają żywotność sztucznych stawów, co najczęściej jest przyczyną operacji rewizyjnych, wskutek obluzowania się elementów nośnych endoprotezy...
-
Układ kompensacji wpływu wzniesienia oraz przyspieszenia w przyczepie do badania oporu toczenia
PublicationW artykule przedstawiono metodę pomiaru współczynnika oporu toczenia przy wykorzystaniu przyczepy opracowanej w Zakładzie Pojazdów na Politechnice Gdańskiej. Następnie omówiono opatentowany układ bezwładnościowy do korekcji wpływu wzniesienia oraz metodę korekcji wpływu przyspieszenia wzdłużnego. W dalszej części przedstawiono przykładowe wyniki obrazujące pomiar współczynnika CRR na wzniesieniu przy zmiennej prędkości.
-
Tyre rolling resistance and its influence on fuel consumption
PublicationRolling resistance of tyres is one of the major resistive forces acting on any wheeled vehicle. Unfortunately, it is also one of the forces very difficult to measure. It is estimated that in certain traffic conditions (like for example constant speed driving with slow or moderate speed) so called Rolling Resistance Impact Factor may be as high as 0.3. This means that reduction of rolling resistance by 50% would lead to 15% of energy...
-
THE USE OF THE Ti-13Zr-13Nb ALLOY POWDER FOR MANUFACTURING OF PROSTHETIC PARTS BY SELECTIVE LASER MELTING
PublicationThe 3D printing is a manufacturing technique belonging to the additive methods able to prepare the designed parts for various purposes. The present reasearch was aimed to fabricate the prosthetic foundations and bridges made of the new Ti-13Zr-13Nb alloy by the selective laser melting (SLM) of a metal powder. The scanning electron examinations and micro scanning tomography were used to investigate the surface quality and intrinsic...
-
THE INFLUENCE OF HOUSING ARRANGEMENT AND INTERFERENCE ON PRELOAD AND THEORETICAL LIFETIME OF A SYSTEM OF TAPER ROLLER BEARINGS OF A HIGH SPEED SHAFT OF A WIND TURBINE GEARBOX
PublicationA system of two taper roller bearings can carry loads with a high ratio of axial load to radial load. Such a system was proposed for a wind turbine gearbox following the poor durability of original bearing design with the aim of increasing durability. Because of size limits, a proposed system is composed of two different taper roller bearings. Standard manufacturers’ catalogues do not provide information on recommended preload...
-
THE ANALYSIS OF THE INFLUENCE OF STRESS DISTRIBUTION ON WEAR PROFILE IN LUBRICATED SLIDING CONTACT OF UHMW-PE VS TITANIUM Ti-13Nb-13Zr ALLOY
PublicationMetal – polymer sliding contacts are a typical combination in industry and medicine. For decades such a set of materials has been the primary choice in human joints endoprosthetic technology. In this paper tribological issues of are presented from a research on the potential for practical use of Ti-13Nb-13Zr/UHMW-PE couple for orthopedic endoprosthesis. In tests on simplified models it is critically important to carefully...
-
Shooting Gas Cylinders to Prevent Their Explosion in Fire
PublicationGas cylinders in general, and particularly cylinders containing acetylene, constitute a great potential danger to fire and rescue services involved in salvage operations. Experiments show that gas cylinders with acetylene, oxygen, hydrogen, CNG, LPG or CO2 may blow after short exposition to heat with very destructive effect as fragments of blown cylinder may fly even several hundred meters. In the case of acetylene the explosion...
-
Selective Laser Melting of Ti Alloy for Manufacturing The Prosthetic Elements
PublicationThe selective laser melting (SLM) is the additive manufacturing method of custom-designed parts. The used materials and the applications are various, including medicine. The titanium and its alloys are materials for which the dimensional quality, surface smoothness and no or extremely low porosity are difficult to reach. In this paper, the successful attempt to obtain by SLM the individually designed prosthetic bridges is described....
-
Search for the most useful geometry of an acoustic journal bearing
PublicationComputer simulations of a number of journal bearing’s geometries utilising acoustic levitation were carried out. The choice of the best geometry depended on the ability of a deformed shape, created by piezo-electric elements, to facilitate squeeze film ultrasonic levitation, and also to create three evenly distributed diverging aerodynamic gaps. Deformations of analysed variants of the bearing’s shape were generated by numerical...
-
Rolling resistance and tyre/road noise on rubberised asphalt pavement in Poland
PublicationThe paper presents results of tyre/road noise and rolling resistance measurements performed on stone mastics asphalt (SMA) that contains rubberised asphalt, developed and produced by a refinery in Poland. Bituminous binder was modified with polymer and addition of crumb rubber. The first observations of asphalt mixture with the new kind of modified bitumen used on the field section are presented. Rolling resistance of passenger...
-
Road texture influence on tyre rolling resistance
PublicationTyre performance, one of the critical factors for vehicle users, is strongly related to theroad surface characteristics, most notably to the pavement texture. Phenomena that occur at the tyre/road interface affect tyre friction (skid resistance), rolling resistance, tyre wear and tyre/road noise. This article deals with relationship between surface texture and rolling resistance of light and heavy vehicle tyres. Mean profile depth...
-
Reduction of road traffic noise by source measures — present and future strategies
PublicationThe current trend worldwide is less focused on reducing road traffic noise. This is in strong contrast to the severe impact of traffic noise to the general health and quality of life. A more holistic and combined strategy is needed. Current international rules and regulations regarding vehicles and tyres are not sufficient to reduce traffic noise levels in an effective way. Calculations show that these regulations will only yield...
-
Przyczepa do pomiaru oporu toczenia opon i nawierzchni drogowych - wybrane zagadnienia
PublicationW artykule przedstawiono zasadę pomiaru współczynnika oporu toczenia opon i nawierzchni drogowych przy wykorzystaniu przyczepy R2 Mk2, skonstruowanej i wykonanej na Politechnice Gdańskiej. Pokazano przykładowe przebiegi dla uzyskanego współczynnika oporu toczenia oraz możliwość tworzenia trajektorii w Google Maps przy wykorzystaniu współrzędnych geograficznych z modułu GPS. W dalszej części omówiono pomiar średniej głębokości profilu...
-
Prospects of Decreasing Power Losses in a Hydrostatic Thrust Bearing
PublicationIn numerous machines, axial load is carried by tilting pad thrust bearings known since the beginning of 20th century. These bearings are commonly bath lubricated, which is simple, does not require any additional pumps, and, due to this, such systems are highly reliable. In a contemporary technology, however, minimization of friction losses became an important goal of machinery improvement. Calculations based on elementary rules...
-
Projekt stanowiska badawczego do wyznaczania charakterystyki ogólnej silnika spalinowego ZS przy wykorzystaniu hydraulicznego układu odbioru mocy
PublicationPrzedstawiono projekt stanowiska badawczego służącego do wyznaczania charakterystyki ogólnej silnika pojazdu ciężarowego, wykorzystując przystawkę odbioru mocy do napędu układu hydraulicznego generującego obciążenie silnika w różnych punktach jego pracy. Przedstawiono założenia projektowe oraz ograniczenia konstrukcyjne. Omówiono zasadę działania stanowiska i metodę wyznaczania charakterystyki. Opisano układ hydrauliczny oraz układ...
-
Projekt mechanizmu różnicowego do pojazdu samochodowego z zachowaniem wymogów jakościowych ISO/TS 16949
PublicationW artykule przedstawiono proces projektowania mechanizmu różnicowego. Dokonano wyboru koncepcji z pośród istniejących rozwiązań stosowanych obecnie w pojazdach samochodowych. Skupiono się przede wszystkim na przebiegu procesu wykonania prototypu z zachowaniem wymogów i standardów ISO/TS 16949 dla produktu i projektu.
-
Pavement ageing influence on tyre/road noise
PublicationRoad surface should be constructed in a way that ensures safe and comfortable traffic conditions, not only when it is newly paved but also during its entire lifetime. An important factor in the asphalt mixture design process is also the expected pavement durability and stability of pavement properties over time. In many countries, road surface starts to play a significant role in traffic noise reduction actions. Selecting a particular...
-
Nowa metoda wyznaczenia pola powierzchni skóry przedramienia i dłoni wykorzystująca sztuczną sieć neuronową
PublicationW artykule przedstawiono rozbieżności pomiędzy wartościami pola powierzchni skóry obliczonymi za pomocą znanych metod a ich rzeczywistymi wartościami. Wykorzystując skaner 3D o wysokiej dokładności, zmierzono pole powierzchni skóry przedramienia i dłoni. Zaobserwowano, że błędy obliczeń są w wysokim stopniu skorelowane z wartościami BMI badanych osób. W grupie osób o BMI poniżej 20 stwierdzono maksymalny błąd względny wynoszący...
-
Noise related to gas bottles explosions
PublicationModern industrialized world is in a never ending danger of accidents and catastrophes of technical nature. Some of them may involve fires and explosions of gas storage bottles or containers. Technical University of Gdansk, Poland performed numerous tests where bottles containing acetylene, oxygen, hydrogen, CO2, LPG, LNG or CNG were blown due to excessive temperature caused by fire. Although those experiments were not focused on...
-
Niekonwencjonalne koła pojazdów
PublicationPrzedstawiono sposoby zapobiegania skutkom utraty ciśnienia w oponach pneumatycznych. Zaprezentowano koła niepneumatyczne, zastosowane w pojeździe księżycowym. Omówiono wyniki badań kół kompozytowych. Przedstawiono najnowsze rozwiązania konstrukcyjne koł niepneumatycznych przeznaczonych do pojazdów mechanicznych.
-
Liquefaction of macroalgae Enteromorpha biomass for the preparation of biopolyols by using crude glycerol
PublicationThis article describes the liquefaction process of macroalgae Enteromorpha with the use of crude glycerol as a solvent and a reagent, aimed at obtaining of new bio-polyols, which are characterized with respect to their chemical structure, physical and thermal properties. Six different biopolyols were prepared. In order to optimize the liquefaction of algal biomass for the best bio-polyol properties, two catalysts (sulfuric or orthophosphoric...
-
Investigation method of large-volume tire with mobile test rig
PublicationThe goal of this research is to develop the tire test method and mobile tire test rig. The test rig enables measurement of tire properties as stiffness and viscous damping in vertical direction, and tire–ground characteristics on the asphalt rigid surface. The tire-ground characteristics are measured by force and a torque measurement hub. The design, calibration and the algorithm for calculating the forces in the wheel center are...
-
Improvement of the thrust bearing calculation considering the convectional heating within the space between the pads
PublicationA modern thrust bearing calculation tool should consider not only the oil film between pad and rotating collar but also the space between the pads. The oil flow in the space has a significant influence on the oil film inlet temperature, the convectional cooling of pad and collar and should be included in the bearing calculation methods. The authors use a tool developed at Clausthal University of Technology in cooperation with the...
-
Hydrodynamiczne łożyska wzdłużne z warstwą ślizgową z PEEK
PublicationMonografia zawiera podsumowanie stanu wiedzy w zakresie hydrodynamicznych łożysk wzdłużnych z polimerową warstwą ślizgową uzupełnione o wyniki badań własnych autora w tym obszarze. W pierwszej części przedstawiono obszerny przegląd znanych z literatury wyników badań, a także opis doświadczeń eksploatacyjnych łożysk z wahliwymi segmentami z pokryciem powierzchni ślizgowej materiałami polimerowymi na bazie PTFE oraz PEEK. Materiały...
-
Field Tests on Hydrodynamic and Hybrid Operation of a Bidirectional Thrust Bearing of a Pump-Turbine
PublicationIn vertical shaft pump turbines operating in pumped storage power plants an important role is played by a thrust bearing. Due to the bidirectional character of operation, thrust bearing tilting pads have to be supported symmetrically, which is known to be unfavourable from the point of view of their performance. Large thrust bearings have to be carefully designed so as to minimise excessive thermo-elastic pad deformations. The...
-
Field tests on hydrodynamic and hybrid operation of a bi-directional thrust bearing of a pump-turbine
PublicationIn vertical shaft pump turbines operating in pumped storage power plants an important role is played by a thrust bearing. Because of bi-directional character of operation, thrust bearing tilting pads have to be supported symmetrically, which is known to be unfavourable from the point of view of their performance. Large thrust bearings have to be carefully designed so as to minimise excessive thermo-elastic pad deformations. The...
-
Extended duration running and impulse loading characteristics of an acoustic bearing with enhanced geometry
PublicationThis paper presents performance during prolonged running of the acoustic bearing when PZTs are switched off and when they are switched on. The effect of active PZT on shaft’s displacements in X and Y directions is clearly demonstrated. Performance of the acoustic bearing was also assessed when an impulse force was applied to the running shaft at speed. Once again the benefits of having PZTs active are beyond doubt. The instability...
-
Design of a test bench for determining the general characteristics of an internal combustion engine using a hydraulic power take-off system
PublicationThe paper presents a design of an engine test bench, which is used to determine the general characteristics of a truck engine using a power take-off (PTO). PTO drives a hydraulic system that generates a load on the engine at various points in its operation in the power range specified by the hydraulic system. The design allows for stationary and mobile tests with the test bench mounted on the truck, without any modification of...
-
Degradation of reference tyres used for CPX measurements
PublicationMeasurements of tyre/road noise using the Close Proximity Method are based on reference tyres that are described in ISO/TS 11819-3. The standard specifies two tyres, namely "P1" and "H1" that should be used during measurements. To be used for measurements each tyre must fulfill certain conditions that are listed in the standard. The conditions are related to the tread pattern depth and rubber hardness. During experiments performed...
-
Charakterystyka porównawcza zgazowania drewna bukowego i RDF w reaktorze przeciwprądowym
PublicationRozproszone małe układy produkcji ciepła to coraz popularniejszy trend w energetyce. Praca opisuje możliwości zgazowania biomasy i odpadów w reaktorze przeciwprądowym małej mocy. Zgazowanie odpadów jest obiecującą metodą ich utylizacji. W pracy porównano rozkład temperatur uzyskany podczas zgazowania biomasy i WPS dla całej wysokości reaktora. Porównane zostały składy gazu generatorowego oraz jego kaloryczność. Podczas prób badano...
-
Analysis of the possibility of determining the general characteristics using the operational data of a vehicle engine
PublicationThe paper presents an analysis of the possibility of determining the general characteristics using the operational data of an engine of refuse collection vehicle. Data acquisition was done by reading information from the CAN network using FMS standard (Fleet Management System), which is widely used in heavy duty vehicles since year 2002. The paper presents the analysis of the expected measurement uncertainties resulting from the...
-
ANALIZA PORÓWNAWCZA DROGI HAMOWANIA MOTOCYKLA Z WŁĄCZONYM I WYŁĄCZONYM UKŁADEM ABS
PublicationW artykule przedstawiono wyniki pomiaru drogi hamowania motocykla przy użyciu hamulca koła przedniego, koła tylnego oraz kombinacji obu tych hamulców. Próby intensywnego hamowania motocykla przeprowadzono na suchej nawierzchni asfaltowej z włączonym i wyłączonym układem ABS. Na podstawie zmierzonej drogi hamowania dokonano obliczenia średniego opóźnienia hamowania.
-
Accurate rolling resistance Rolling resistance measurements can be influenced by a number of factors
PublicationTire rolling resistance is one of the most difficult-to-measure parameters of the tire/ pavement interface, especially if road measurements are required. First of all, it is necessary to measure a fairly small force in the system that is heavily loaded by other forces and subjected to many adverse effects causing measurement errors. The second problem is related to the fact that tire rolling resistance depends on many factors,...
-
3D Printing of Metallic Implants
PublicationThe fabrication of various elements, solid and open porous structures of stainless steel and Ti alloy is described. The process was started with the design of 3D models in CAD/CAM system. The 3D models were transformed into *.stl files and then the manufacturing process of the real structures by means of the selective laser melting with the SLM Realizer 100 3D printer was made. The paper shows the porous specimens made for possible...
Year 2018
-
Tire/Road Noise On Poroelastic Road Surfaces - Results Of Laboratory Measurements
PublicationTire/road noise is the most important part of traffic noise for medium and high speed driving both in the case of passenger cars and trucks. The potential to make modification of tires that significantly reduce tire/road noise in nearly over, at least for conventional tires so the only promising action is to improve road pavements. One of the innovative solutions is poroelastic road pavement (PERS) that reduces airflow related...
-
TIRE/ROAD NOISE AND TIRE ROLLING RESISTANCE ON PROTOTYPE PERS SURFACE
PublicationPoroelastic road surfaces are characterized by low noise of tires running on them.Road pavements of this type are promising solution to problems related to traffic noise in cities and on rural roads. Some technical problems still have to be solved, in particular regarding durability and skid resistance on wet surface. Ongoing and planned works are to contribute to create a quiet, durable and safe road surface, which will become...