Filtry
wszystkich: 1498
wybranych: 1300
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: arylated carbon nanotubes
-
Amperometric sensing of chemical oxygen demand at glassy carbon and silicon electrodes modified with boron-doped diamond
Publikacja.A boron-doped diamond (BDD) sensor is proposed for effective detection of chemical oxygen demand (COD) by means of amperometric technique. Boron-doped diamond thin films, acting as active sensors, were deposited on both silicon wafer and glassy carbon (GC) substrates by microwave plasma assisted chemical vapour deposition. SEM micrographs showed that BDD–Si displays triangle-faceted crystallites ca. 0.5–3 μm in size, while BDD–GC...
-
Compact High Efficiency and Zero-Emission Gas-Fired Power Plant with Oxy-Combustion and Carbon Capture
PublikacjaReduction of greenhouse gases emissions is a key challenge for the power generation industry, requiring the implementation of new designs and methods of electricity generation. This article presents a design solution for a novel thermodynamic cycle with two new devices—namely, a wet combustion chamber and a spray-ejector condenser. In the proposed cycle, high temperature occurs in the combustion chamber because of fuel combustion...
-
Stannates, titanates and tantalates modified with carbon and graphene quantum dots for enhancement of visible-light photocatalytic activity
PublikacjaMost efforts in heterogeneous photocatalysis are focused on development of new and stable photoactive materials efficient in degradation of various pollutants under visible-light irradiation. In this regard, the wide-bandgap perovskite semiconductors, i.e., SrTiO3 (titanate), SrSnO3 (stannate) and AgTaO3 (tantalate), were prepared by a solvothermal method, and then modified with carbon quantum dots (CQDs) or graphene quantum dots...
-
Reactivity of bulky aminophosphanes towards small molecules: Activation of dihydrogen and carbon dioxide by aminophosphane/borane frustrated Lewis pairs
PublikacjaA series of mono- and bisaminophosphanes with formulas R2NPR’R’’ and (R2N)2PR’ (R = iPr, Cy; R’ = Ph, Cy; R’’ = iPr) were characterized by X-ray analysis, NMR spectroscopy and computational methods. The common structural futures of these species are short and polarized PAN bonds, a pyramidal geometry at the P atom and an almost planar geometry at the N atoms. According to DFT calculations, these...
-
Comparison of Gold Nanoparticles Deposition Methods and Their Influence on Electrochemical and Adsorption Properties of Titanium Dioxide Nanotubes
Publikacja -
The Effect of Laser Re-Solidification on Microstructure and Photo-Electrochemical Properties of Fe-Decorated TiO2 Nanotubes
Publikacja -
Synergisms and antagonisms between MoS2 nanotubes and representative oil additives under various contact conditions
Publikacja -
Physico-chemical properties and possible photocatalytic applications of titanate nanotubes synthesized via hydrothermal method
Publikacja -
Synergistic effect of nanoscale carbon black and ammonium polyphosphate on improving thermal stability and flame retardancy of polypropylene: A reactive network for strengthening carbon layer
Publikacja -
Direct determination of paraquat herbicide by square-wave voltammetry by two-step transfer mechanism at heterogeneous boron-doped carbon nanowall electrodes
PublikacjaBoron-doped carbon nanowalls (B:CNW) versus boron-doped diamond (BDD) materials were investigated for the effective electrochemical detection of highly toxic herbicide paraquat (PQ). Depending on the surface morphology and functional groups of BDD and B:CNWs, the electrochemical absorption and detection of the target analyte PQ revealed different detection mechanisms. The surface absorption mechanism was mainly observed for BDD,...
-
Multi-pathway mechanism of polydopamine film formation at vertically aligned diamondised boron-doped carbon nanowalls
PublikacjaBoron-doped carbon nanowall (B:CNW) electrodes were used as a platform for studying the electropolymerisation of dopamine. Due to the unique properties of B:CNW, including the fast charge-transfer kinetics and high surface conductivity, a high degree of reversibility of redox reactions was achieved. Three separated redox peaks were observed on voltammograms and attributed to three fundamental reactions in the dopamine polymerisation...
-
Experimental and analytical thermal study of PTFE composite sliding against high carbon steel as a function of the surface roughness, sliding velocity and applied load
PublikacjaThis study investigates the contact temperatures caused by frictional heating of sliding parallel pairs. In this case the materials studied are a PTFE composite in contact with a high carbon steel plate. These materials are commonly used for industrial applications, in particular as the main contacting components within a scroll expander system. The expected contact temperature values are important to be quantified in order to...
-
Acclimation of denitrifying activated sludge to a single vs. complex external carbon source during a start-up of sequencing batch reactors treating ammonium-rich anaerobic sludge digester liquors
PublikacjaIn this study, denitrification of ammonium- reach anaerobic sludge digester liquor was investigated during start-up periods of two laboratory- scale ‘‘fill-and-draw’’ reactors. One reactor was fed with a single carbon source (ethanol), whereas the other reactor was fed with a complex carbon source (fusel oil). During two acclimation experiments, the structure of microbial community involved in denitrification was analyzed using...
-
On analysis of nanocomposite conical structures
PublikacjaThis research examines the analysis of rotating truncated conical baskets reinforced by carbon nanotubes around the two independent axes. A time-dependent analysis is considered, and the nonlinear dynamic governing equations are extracted using the energy method. Carbon nanotubes (CNTs) reinforced the conical basket, and the structure's mechanical properties are determined based on the several distributions of carbon nanotubes....
-
Role of the sulfur to α-carbon thioether bridges in thurincin H
Publikacja -
Photocatalytic activity and surface properties of carbon-doped titanium dioxide
PublikacjaTiO2 domieszkowany węglem otrzymano poprzez hydrolizę izopropanolanu tytanu(IV) i kalcynację w 350ºC w atmosferze powietrza przez 2h. Przeprowadzone badania wykazały, że fenol (0.21 mM) jest efektywnie degradowany w fazie wodnej, w obecności otrzymanego fotokatalizatora oraz światła z zakresu widzialnego (λ>400 nm). Pole powierzchni właściwej otrzymanego C-TiO2 wynosiło około 127 m2/g, fotokatalizator absorbuje światło z zakresu...
-
Total and mineralizable soil carbon as affected by tillage in the Argentinean Pampas
Publikacja -
Carbon Monoxide Fate in the Environment as an Inspiration For Biorefinery Industry: A Review
Publikacja -
Carbon Nanohorns as Reaction Nanochambers – a Systematic Monte Carlo Study
Publikacja -
Preparation and characterization of TiO2/carbon nanowall composite on a transparent substrate
Publikacja -
Preliminary studies on the evolution of carbon assimilation abilities within Mucorales
Publikacja -
Carbon assimilation profiles of mucoralean fungi show their metabolic versatility
Publikacja -
Recent Progress in Polymer Waste-Derived Porous Carbon for Supercapacitors
Publikacja -
CO2 Adsorption Study of Potassium-Based Activation of Carbon Spheres
Publikacja -
TiO2-anatase modified by carbon as the photocatalyst under visible light
Publikacja -
MgO/CaO-loaded porous carbons for carbon dioxide capture
Publikacja -
Carbon‐Nanotube‐Based Stimuli‐Responsive Controlled‐Release System
Publikacja -
Conjugation of polyethylenimine and its derivatives to carbon-encapsulated iron nanoparticles
Publikacja -
Carbon catalysts from pine cones – Synthesis and testing of their activities
Publikacja -
Influence of stress on oxidation behaviour of carbon steel studded coil.
PublikacjaAnalizowano awarię wężownicy kołkowej ze stali węglowej pracującej przez 10 lat w środowisku przegrzanej pary w temperaturze 290ºC i ciśnieniu 0,67 MPa. Obserwacje mikroskopowe powierzchni i przekroju rury ukazały drobne pęknięcia w ściance wynikające z procesu selektywnego utleniania. Zastosowano metodę elementów skończonych w celu ustalenia zależności postępu korozji od ciśnienia i obciążenia cieplnego.
-
Oxide catalysts for carbon nanotube and few layer graphene formation
Publikacja -
On the graphitisation role of oxide supports in carbon nanotube CVD synthesis
Publikacja -
Correction: MOF-5 derived carbon as material for CO2 adsorption
Publikacja -
On the use of Cu catalysts for tailoring carbon nanostructures in alcohol‐CVD
Publikacja -
Facile synthesis and properties of iron oxide spheres coated with carbon
Publikacja -
Thermal and Electrical Characterization of the Carbon Nanofibers Based Cement Composites
Publikacja -
Physicochemical and photocatalytic characterization of mesoporous carbon/titanium dioxide spheres
Publikacja -
Modified Manganese Phosphate Conversion Coating on Low-Carbon Steel
PublikacjaConversion coatings are one of the primary types of galvanic coatings used to protect steel structures against corrosion. They are created through chemical reactions between the metal surface and the environment of the phosphating. This paper investigates the impact that the addition of new metal cations to the phosphating reaction environment has on the quality of the final coating. So far, standard phosphate coatings have contained...
-
Chestnut-Derived Activated Carbon as a Prospective Material for Energy Storage
PublikacjaIn this work, we present the preparation and characterization of biomass-derived activatedcarbon (AC) in view of its application as electrode material for electrochemical capacitors. Porouscarbons are prepared by pyrolysis of chestnut seeds and subsequent activation of the obtainedbiochar. We investigate here two activation methods, namely, physical by CO2and chemical usingKOH. Morphology, structure and specific surface area (SSA)...
-
Fluorescence emission of carbon disulfide in low energy electron collision.
PublikacjaZbadano widma emisyjne dwusiarczku węgla w zakresie widmowym od 235 nm do575 nm wzbudzane zderzeniami elektronów o energii 9.7eV I 15eV. W otrzymanych widmach największe natężenie miały pasma pochodzące z dysocjacji cząsteczek dwusiarczku węgla.
-
Cementite transformation in low carbon steel under the influence of sulphur.
PublikacjaBadano cementyt (węglik Fe3C) w przemysłowym gatunku stali niskowęglowej po długotrwałej eksploatacji w benzynie ciężkiej, zawierającej 0,3 ppm siarki, o temperaturze 200-220C. Wykazano, że cementyt na powierzchni i we wnętrzu stali ulega przemianie w niestabilną, quasi-krystaliczną fazę wzbogaconą w siarkę i pierwiastki domieszkowe a zubożoną w żelazo. Przemiana cementytu i rozpad zdegradowanej fazy związana jest z uwolnieniem...
-
Elemental and water-insoluble organic carbon in Svalbard snow: a synthesis of observations during 2007–2018
PublikacjaLight-absorbing carbonaceous aerosols emitted by biomass or fossil fuel combustion can contribute to amplifying Arctic climate warming by lowering the albedo of snow. The Svalbard archipelago, being near to Europe and Russia, is particularly affected by these pollutants, and improved knowledge of their distribution in snow is needed to assess their impact. Here we present and synthesize new data obtained on Svalbard between 2007...
-
Wyznaczanie współczynnika przejmowania ciepła podczas wrzenia w przepływie dwutlenku węgla (Prediction of flow boling heat transfer coefficient for carbon dioxide in minichannels)
PublikacjaW pracy przedstawiono wyniki obliczeń uzyskane za pomocą własnego modelu półemirycznego dla wybranych danych eksperymentalnych dla wrzenia w przepływie dwutlenku węgla. Metoda obliczeniowa została zweryfikowana z danymi eksperymentalnymi Docoulombiera i innych (2011) oraz Mastrullo i innych (2009). Badania eksperymentalne dotyczą pełnego zakresu zmienności stopnia suchości oraz zakresu prędkości masowej G=200-1200 kg/m2s. rozwijany...
-
The Influence of the Parameters of a Gold Nanoparticle Deposition Method on Titanium Dioxide Nanotubes, Their Electrochemical Response, and Protein Adsorption
Publikacja -
Correction: Highly stable organic–inorganic junction composed of hydrogenated titania nanotubes infiltrated by a conducting polymer
Publikacja -
The pulsed laser ablation synthesis of colloidal iron oxide nanoparticles for the enhancement of TiO2 nanotubes photo-activity
PublikacjaThe rapid, only a few minutes long synthesis of FeO, Fe3O4, and Fe2O3nanoparticles mixture utilizing the pulsedlaser ablation using simply pure iron target and water was demonstrated. The size and crystal phase of Fe-basedNPs were characterized using DLS and HR-TEM techniques, respectively. The metastable suspension of FeO,Fe3O4, and Fe2O3nanoparticles was used to the decoration of anodized TiO2nanotubes (TiO2-NTs) by means ofthe...
-
An integral-differential method for impedance determination of the hydrogen oxidation process in the presence of carbon monoxide in the proton exchange membrane fuel cell
PublikacjaThe impedance of a proton exchange membrane fuel cell powered by hydrogen contaminated with carbon monoxide, ranging from 150 to 300 ppb, is measured and discussed. The tested range of CO concentration complied with the fuel standard specified in the ISO standards. Studies of influence of CO contamination on operation of PEMFC are crucial for further development and commercialization of fuel cells for automotive applications. Based...
-
Quantum and carbon dots conjugated molecularly imprinted polymers as advanced nanomaterials for selective recognition of analytes in environmental, food and biomedical applications
PublikacjaSamples with complex matrix analyzed during explanation of pathogenesis of various diseases and food or environmental monitoring request advanced analytical and instrumental devices. Among the materials used for described purposes, quantum (QDs) or carbon dots (CDs) layered by molecularly imprinted polymer (MIP) shells have gained widespread attention. Unique optical and physicochemical properties of QDs/CDs together with high...
-
Thermosensitive composite based on agarose and chitosan saturated with carbon dioxide. Preliminary study of requirements for production of new CSAG bioink.
PublikacjaThis study introduces a method for producing printable, thermosensitive bioink formulated from agarose (AG) and carbon dioxide-saturated chitosan (CS) hydrogels. The research identified medium molecular weight chitosan as optimal for bioink production, with a preferred chitosan hydrogel content of 40–60 %. Rheological analysis reveals the bioink's pseudoplastic behavior and a sol-gel phase transition between 27.0 and 31.5 °C. The...
-
Leveraging food waste for electricity: A low-carbon approach in energy sector for mitigating climate change and achieving net zero emission in Hong Kong (China)
PublikacjaIn recent years, food waste has been a global concern that contributes to climate change. To deal with the rising impacts of climate change, in Hong Kong, food waste is converted into electricity in the framework of low-carbon approach. This work provides an overview of the conversion of food waste into electricity to achieve carbon neutrality. The production of methane and electricity from waste-to-energy (WTE) conversion are...