Filtry
wszystkich: 1354
wybranych: 1168
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: NUMERICAL ANALYSIS
-
Numerical Investigation on Dynamic Performance of a Multi-storey Steel Structure Model and Comparison with Experimental Results
PublikacjaShaking table testing is the most commonly adopted method to simulate earthquake forces. This approach allows us to analyze the dynamic performance and provides a valuable insight into the dynamics of building structures, which helps to improve their future safety and reliability. The present study aims to conduct a numerical evaluation of dynamic response of a multi-storey steel structure model, which was previously examined during...
-
Numerical simulation of the influence of the selected factors on the performance of a concrete road barrier H2/W5/B
PublikacjaThis paper discuss the influence of selected factors on the performance of a concrete road barrier H2/W5/B. Modelling techniques of a concrete road safety system were briefly discussed. Comparison to the full scale crash test results has been shown. The concrete road safety barrier has been investigated for evaluation of the overall damage after collision under various initial conditions. The failure assessment criterion has been...
-
Comparing N3-60 cascade exit angles obtained from tunnel measurements and numerical calculations
PublikacjaThe article compares the results of measurements performed in the aerodynamic tunnel at CUT and numerical simulation carried out for a plane cascade of N3-60 profiles. Comparing the measured and calculated results provides opportunities for assessing the range of systematic differences between simulation predictions and actual experimental results.
-
Numerical Solution of the Two-Dimensional Richards Equation Using Alternate Splitting Methods for Dimensional Decomposition
PublikacjaResearch on seepage flow in the vadose zone has largely been driven by engineering and environmental problems affecting many fields of geotechnics, hydrology, and agricultural science. Mathematical modeling of the subsurface flow under unsaturated conditions is an essential part of water resource management and planning. In order to determine such subsurface flow, the two-dimensional (2D) Richards equation can be used. However,...
-
Numerical investigation on dynamic performance of a multi-storey steel structure model and comparison with experimental results
PublikacjaShaking table testing is the most commonly adopted method to simulate earthquake forces. This approach allows us to analyze the dynamic performance and provides a valuable insight into the dynamics of building structures, which helps to improve their future safety and reliability. The present study aims to conduct a numerical evaluation of dynamic response of a multi-storey steel structure model, which was previously examined during...
-
EXPERIMENTAL AND NUMERICAL INVESTIGATION ON SPECIMEN GEOMETRY EFFECT ON THE CTOD VALUE FOR VL-E36 SHIPBUILDING STEEL
PublikacjaThere are special cases in the marine industry, where additional material tests, such as the fracture toughness test, must be performed. Additional fracture toughness tests, such as CTOD (Crack Tip Opening Displacement), are typically performed on three-point bend specimens. The dimension that defines all the specimen dimensions is the thickness of the material to be tested. It is recommended by classification societies (e.g. DNVGL)...
-
Size effect in concrete beams under bending – influence of the boundary layer and the numerical description of cracks
PublikacjaIn the paper the size effect phenomenon in concrete is analysed. The results of numerical simulations of using FEM on geometrically similar un-notched and notched concrete beams under bending are presented. Concrete beams of four different sizes and five different notch heights under three-point bending test were simulated. In total 18 beams were analysed. Two approaches were used to describe cracks in concrete. First, eXtended...
-
Numerical modelling of different airbag folding patterns and their influence on occupant responses in frontal vehicle impact
PublikacjaThis paper presented a procedure for airbag folding for the application in occupant safety studies and analysed the influence of different airbag folding patterns on the occupant severity in frontal impact. Airbags were folded in two patterns: zig-zag and top-roll, using two folding techniques: Initial Metric Method and Explicit Folding. The explicit folding was found to be more expensive in terms of preparation time. However,...
-
Two - scale model for concrete beams subjected to three point bending - numerical analyses and experiments
PublikacjaArtykuł omawia dwu-skalowe podejście do betonu przy wykorzystaniu połączonych modeli. Metodę elementów skończonych zastosowano na poziomie makro. Na poziomie mikro zastosowano metodę elementów dyskretnych. Macierz sztywności wyznaczono na podstawie tensora naprężeń wyznaczonego w skali mikro. Wyniki numeryczne dw-skalowe porównano z wynikami dyskretnymi dla całego obszaru.
-
Experimental and numerical investigations of concrete behaviour at meso-level during quasi-static splitting tension.
PublikacjaArtykuł omawia wyniki numeryczne dotyczące pękania betonu uzyskane stosując metodę elementów dyskretnych. Dwuwymiarowe obliczenia wykonano dla próbek betonowych podczas rozłupywania. Beton został opisany jako model 4-fazowy. Mikrostruktura betonu odpowiadała zdjęciom tomograficznym. Zbadano wpływ warunków brzegowych na proces pękania. W obliczeniach zwrócono uwagę na porzebieg zjawisk mikrostrukturalnych przebieg pękania. Wyniki...
-
EXPERIMENTAL AND NUMERICAL INVESTIGATIONS OF CONCRETE BEHAVIOUR AT MESO-LEVEL DURING QUASI-STATIC SPLITTING TENSION
PublikacjaThe paper describes experimental and numerical results of quasi-static splitting tensile tests on concrete specimens at meso-scale level. The loading strip was made of plywood or steel. Fracture in concrete was detected at the aggregate level by means of three non-destructive methods: 3D x-ray micro-computed tomography, 2D scanning electron microscope and manual 2D digital microscope. The discrete element method was used to directly...
-
Numerical simulations of a triaxial test in granular bodies using discrete particle simulations with contact moments
PublikacjaW artykule przedstawiono wyniki symulacji badania trójosiowego dla materiałów granulowanych. Obliczenia wykonano przy zastosowaniu metody DEM. Pokazano wpływ momentów kontaktowych na wytrzymałość próbki. Zbadano wpływ parametrów mikroskopowych.
-
Experimental and numerical assessment of size effect in geometrically similar slender concrete beams with basalt reinforcement
PublikacjaW artykule przedstawiono doświadczalne i numeryczne wyniki badań efektu skali w geometrycznie podobnych smukłych belkach betonowych ze zbrojeniem bazaltowym. Doświadczenia zostały symulowane stosując metodę elementów skończonych w oparciu o model sprężysto-plastyczny z degradacją sztywności i nielokalnym osłabieniem. Otrzymano dobrą zgodność wyników doświadczalnych z numerycznymi.
-
Nośność konstrukcji gruntowo-łukowej prefabrykowanego wiaduktu w świetle obliczeń numerycznych i badań „in situ”
PublikacjaWartykule przedstawiono analizy przeprowadzone dla wiaduktu WK-15 Pomorskiej Kolei Metropolitalnej wykonanego w technologii łuków prefabrykowanych przykrytych gruntem (system TechSpan). W celu weryfikacji obliczeń numerycznych wykonano próbne obciążenie konstrukcji. Przedstawiono wyniki pomiarów naprężeń i prezmieszczeń konstrukcji. Odniesiono się krytycznie do zastosowanego modelu obliczeniowego.
-
Damage-involved response of two colliding buildings under non-uniform earthquake loading
PublikacjaPounding between insufficiently separated buildings, which may result in considerable damage or may even lead to the total collapse of colliding structures, has been repeatedly observed during earthquakes. Earthquake-induced collisions of buildings has been intensively studied applying various structural models. It was assumed in the analyses, however, that the seismic excitation is identical for all structural supports; whereas,...
-
Stability and load bearing capacity of a truss with elastic braces
PublikacjaThe present paper is devoted to the numerical and experimental investigations of stability of a truss stiffened by elastic braces. The model of a real roof truss scaled by factor ¼ was investigated. In the research the linear buckling and non-linear static analysis of the truss shell and beam model with geometric and material non-linearity is presented. The initial imperfections were assumed in the form of the first buckling mode....
-
Rainscreen panels deformations mods
PublikacjaIn rainscreen panels designing simplified calculation models are used. For plate computation simply supported panels or panels with fixed edges are commonly used. Such approximations are subjected to large errors that lead to inefficient rainscreen panels design. In order to develop a method for determining the optimal geometry of the rainscreen panels, that would take into consideration the real stiffness of both continuous and...
-
The smoothness test for a density function
PublikacjaThe problem of testing hypothesis that a density function has no more than μ derivatives versus it has more than μ derivatives is considered. For a solution, the L2 norms of wavelet orthogonal projections on some orthogonal ‘‘differences’’ of spaces from a multiresolution analysis is used. For the construction of the smoothness test an asymptotic distribution of a smoothness estimator is used. To analyze that asymptotic distribution,...
-
Entropy function application within the selection process of diagnostic parameters of marine diesel and gas turbine engines
PublikacjaThe paper presents the method of conducting an analysis of the diagnostic informativeness among the parameters characterizing the observed gas dynamic processes carried out within working spaces of marine diesel and gas turbine engines. An entropy function, as the measure of uncertainty of the identified states' set of the engine unfitness was applied. Having evaluated the diagnostic information the most adequate parameters were...
-
DYNAMIC RESPONSE OF FORUM GDANSK STRUCTURE DUE TO RAIL TRAFFIC
PublikacjaThe paper presents the study of the impact of vibration induced by the movement of the railway rolling stock on the Forum Gdańsk structure. This object is currently under construction and is located over the railway tracks in the vicinity of the Gdańsk Główny and Gdańsk Śródmieście railway stations. The analysis covers the influence of vibrations on the structure itself and on the people within. The in situ measurements on existing...
-
Modeling of medium flow processes in transportation pipelines - the synthesis of their state-space models and the analysis of the mathematical properties of the models for leak detection purposes
PublikacjaThe dissertation concerns the issue of modeling the pipeline flow process under incompressible and isothermal conditions, with a target application to the leak detection and isolation systems. First, an introduction to the model-based process diagnostics is provided, where its basic terminology, tools, and methods are described. In the following chapter, a review of the state of the art in the field of leak detection and isolation...
-
Tensile validation tests with failure criteria comparison for various GFRP laminates
PublikacjaThe paper studies the mechanical properties of glass fibre reinforced polymers (GFRP) with various types and orientation of reinforcement. Analyzed specimens manufactured in the infusion process are made of polymer vinyl ester resin reinforced with glass fibres. Several samples were examined containing different plies and various fibres orientation [0, 90] or [+45, –45]. To assess the mechanical parameters of laminates, a series...
-
A review on analytical models of brushless permanent magnet machines
PublikacjaThis study provides an in-depth investigation of the use of analytical and numerical methods in analyzing electrical machines. Although numerical models such as the finite-element method (FEM) can handle complex geometries and saturation effects, they have significant computational burdens, are time-consuming, and are inflexible when it comes to changing machine geometries or input values. Analytical models based on magnetic equivalent...
-
DETERMINATION OF SEAKEEPING PERFORMANCE FOR A CASE STUDY VESSEL BY THE STRIP THEORY METHOD
PublikacjaThe increase of seakeeping performance is of particular importance for car and passenger ferries, service ships in the gas and oil extraction industry and offshore wind power farm industry, as well as for special purpose ships (including military applications). In the water areas of the Baltic Sea, North Sea, and Mediterranean Sea, which are characterised by a short and steep wave, the hull shape has a substantial impact on the...
-
Determination of stepped plate thickness distribution using guided waves and compressed sensing approach
PublikacjaGuided waves recently have attracted significant interest as a very promising research area. The signals registered by a specially designed sensor network are processed to assess the state of the tested structure. Despite the constant development of novel damage detection algorithms employing guided waves, the phenomenon of wave propagation still needs detailed recognizing and understanding for the further progress of non-destructive...
-
Expedited Trust-Region-Based Design Closure of Antennas by Variable-Resolution EM Simulations
PublikacjaThe observed growth in the complexity of modern antenna topologies fostered a widespread employment of numerical optimization methods as the primary tools for final adjustment of the system parameters. This is mainly caused by insufficiency of traditional design closure approaches, largely based on parameter sweeping. Reliable evaluation of complex antenna structures requires full-wave electromagnetic (EM) analysis. Yet, EM-driven...
-
Guided wave propagation in diagnostic of steel elements
PublikacjaThis paper is devoted to numerical investigations of elastic wave propagation in steel elements. The aim of this study is to conduct numerical analysis and experimental investigations on the propagation of elastic waves in steel elements in the context of damage detection. In particular, this paper is devoted to detection of damage occurring in the form of notch or changed thickness. This approach utilized the fact that any discontinuities...
-
Guided wave propagation in diagnostic of steel elements
PublikacjaThis paper is devoted to numerical investigations of elastic wave propagation in steel elements. The aim of this study is to conduct numerical analysis and experimental investigations on the propagation of elastic waves in steel elements in the context of damage detection. In particular, this paper is devoted to detection of damage occurring in the form of notch or changed thickness. This approach utilized the fact that any discontinuities...
-
Thermal-FSI modeling of flow and heat transfer in a heat exchangerbased on minichanels
PublikacjaIn this paper selected numerical modelling problems for an advanced thermal-FSI ("Fluid Solid Interaction") mini-channel heat exchanger model are presented. Special attention is given to the heat transfer between the separated mediums for different mass flows. Similar modelling problems have also been discussed in the literature dedicated to numerical and theoretical modelling problems for typical heat exchangers [1, 2, 3]. Basic...
-
A dynamic vehicle-bridge model based on the modal identification results of an existing EN57 train and bridge spans with non-ballasted tracks
PublikacjaThis paper addresses the methodology of the bridge-vehicle dynamic model definition based on the free response measurements of an existing train and existing bridge spans. In the case of the railway vehicle, the methodology uses the impulse excitations of a single car by means of the wedge method. In the case of the bridge spans, free responses are collected after the passages of trains. The global modal parameters (frequencies...
-
On the generalized model of shell structures with functional cross-sections
PublikacjaIn the present study, a single general formulation has been presented for the analysis of various shell-shaped structures. The proposed model is comprehensive and a variety of theories can be used based on it. The cross-section of the shell structure can be arbitrarily analyzed with the presented equations. In other words, various types of shell structures, including cylindrical, conical, spherical, elliptical, hyperbolic, parabolic,...
-
Spectroscopic studies on physicochemical properties of selected unsymmetrical bisacridine derivatives and NMR analysis of their interactions with the model sequence Pu22 aided by molecular dynamics
PublikacjaIn recent years, new promising acridine derivatives have appeared, belonging to the unsymmetrical bisacridines (UAs) family with high anticancer activity. Both their physicochemical properties and their mechanism of action at the molecular level have not been thoroughly analyzed so far. Four derivatives were selected for the study, termed as: C-2028, C-2041, C-2045 and C-2053. The first aim of this work was to determine the protonation...
-
Experimental investigation and process parameter optimization of sheet metal bending by line heating method
PublikacjaThe present study is concerned with the experimental investigation of sheet metal deforming by line heating method that incorporates the combined effect of traverse speed of the torch, thickness of the sheet metal, and the number of passes of the torch. For the numerical analysis of metal bending by line heating, the
-
Badania i analizy kolejowych konstrukcji odciążających typu mostowego
PublikacjaW pracy przedstawiono i omówiono wybrane modele obliczeniowe, wyniki analiz teoretycznych oraz badań trzech typów kolejowych konstrukcji odciążających typu mostowego. Zaprezentowano modele obliczeniowe oraz metodykę badań in situ tego typu konbstrukcji. Przedstawiono wnioski dotyczące zaawansowanych metod obliczeniowych rozszerzonych badań in situ w celu diagnozowania rzeczywistej pracy obiektów mostowych.
-
THE INTERACTION BETWEEN STEEL COLUMN CHORD AND CLOSELY SPACED REINFORCEMENT.
PublikacjaNowadays, more often than before, civil engineering designers are willing to use steel build-up members composed of single or doubled cold-formed chords interconnected using different mechanical connectors. This paper subject is an analysis of cooperation of a closely spaced built-up cold-formed chord interconnected with series of bolts that are located along the length of the member in a specific spacing. This distance along the...
-
Modelling of elastic wave propagation in a bolted joint using a thin layer of shell elements
PublikacjaThere are many mathematical models describing the propagation of elastic waves through the imperfect boundary of two media. They were successfully applied to modelling of high frequency bulk waves and their interaction with local defects. On the other hand, the existing literature models of bolted connections ignore the aspect of imperfect connection between elements. Therefore, this paper presents the concept of application of...
-
Uncertainty of the liquid mass flow measurement using the orifice plate
PublikacjaThe article presents an estimation of measurement uncertainty of a liquid mass flow using the orifice plate. This subject is essential because of the widespread use of this type of flow meters. Not only the quantitative estimation but also the qualitative results of those measurements are important. To achieve these results the authors of the paper propose to use the theory of uncertainty. The article shows the analysis of the...
-
Probabilistic Methods in Reliability Assessment of Engineering Lightweight Structures
PublikacjaThe paper considers the probability-based analysis of structural safety measures. Two different numerical examples of representative lightweight structures are considered – a submerged truss tower supporting an offshore platform, and an overhead power line support truss tower. On the basis of these examples, the importance of a motivated selection of analysis method and a proper choice of the number of important variables is shown....
-
THEORETICAL POTENTIAL OF HYDROGEN PRODUCTION FROM TEXTILES WASTES IN POMERANIAN REGION BY MEANS OF DARK FERMENTATION
PublikacjaModel has been developed for calculating theoretical mass of hydrogen produced from textile wastes by mean of dark fermentation. As vegetable fibres wastes were chosen two mostly used — cotton and linen (flax). As the synthethic carbohydrate rich fiber was chosen viscose. In the background there were introduced: problems of dark fermentation, characteristics of textile material structure. Additionally pathways of the process...
-
Flexural behavior of composite structural insulated panels with magnesium oxide board facings
PublikacjaThe current report is devoted to the flexural analysis of a composite structural insulated panel (CSIP) with magnesium oxide board facings and expanded polystyrene (EPS) core, that was recently introduced to the building industry. An advanced nonlinear FE model was created in the ABAQUS environment, able to simulate the CSIP’s flexural behavior in great detail. An original custom code procedure was developed, which allowed to include...
-
Safety at railway level crossings and Vision Zero
PublikacjaIn this work, safety analysis at the railway level crossings is presented using advanced mathematical modelling. Resistivity of track subgrade panels is taken into account. The analysis does not refer to the assessment of the current regulations. Specific cases of generalized dynamic system are considered by introducing operations S=Δ, S=P defined in space C(N) of real sequences. In this model, generalized discrete exponential...
-
Development of a Response Assessment Tool for a Floating Dock System
PublikacjaDocking operations of ships require a response assessment to ensure structural and personnel safety. Environmental loads and improper ballast adjustments are the main threats to the docking operations. They can cause severe structural damages and stability loss to a floating dock system which includes a floating dock and a docked vessel, even if the velocities of the dock and the vessel are very low during the docking process....
-
Badania eksperymentalne i numeryczne zachowania się zbiorników stalowych poddanych wstrząsom górniczym i sejsmicznym
PublikacjaW niniejszej dysertacji opisano wyniki kompleksowych badań zachowania się zbiorników stalowych poddanych wstrząsom górniczym i umiarkowanym trzęsieniom ziemi. Badania prowadzono dla dwóch zbiorników rzeczywistych zlokalizowanych na terenie Polski. W pierwszym etapie badań przeprowadzono badania eksperymentalne na specjalnym stanowisku laboratoryjnym dla modeli doświadczalnych zbiorników. Badania prowadzono dla różnego poziomu wypełnienia...
-
Experimental and Computational Analysis of the Ship Propeller in Open Water Conditions for Inclined Flow
PublikacjaThe paper presents the results of computational analyses simulating the open water tests of ship propeller in inclined flow. The results of computations are compared with the results of corresponding experimental analyses carried out in the towing tank of Ship Design and Research Centre (CTO S.A.). The object of the research was the model propeller identified as CP469. The aim of the study was to validate the results of numerical...
-
Extending transition curve in analytical design method
PublikacjaThe paper presents the problem of extending the transitional curves, using for this purpose an analytical design method. The basis for the analysis of numerical calculations were carried out for a wide set of parameters characterizing the standard geometric system. We considered an importance of the size of radius of the circular arc and return angle of route on the obtained results after the formulation of appropriate theoretical...
-
Mechanical properties of the human stomach under uniaxial stress action
PublikacjaThe aim of this study was to estimate the range of mechanical properties of the human stomach in order to use the collected data in numerical modelling of surgical stapling during resections of the stomach. The biomedical tests were conducted in a self-developed tensile test machine. Twenty-two fresh human stomach specimens were used for the experimental study of its general strength. The specimens were obtained from morbidly obese...
-
ON ESTIMATION OF OCCUPANT SAFETY IN VEHICULAR CRASHES INTO ROADSIDE OBSTACLES USING NON-LINEAR DYNAMIC ANALYSIS
PublikacjaThe article describes a comparison of two general methods of occupants safety estimation based on a numerical examples. The so-called direct method is mainly based on the Head Injury Criterion of a crash test dummy in a vehicle with passive safety system while the indirect method uses a European standards approach to estimate impact severity level. Numerical simulations in LS-DYNA have been conducted.
-
Zmodernizowany most Łazienkowski w Warszawie – analizy z wykorzystaniem modelu numerycznego MES
PublikacjaW artykule przedstawiono proces modelowania statycznego przęseł mostu Łazienkowskiego w Warszawie, który został poddany odbudowie po pożarze 14 lutego 2015 r. Sprawdzające obliczenia numeryczne wykonano w związku z badaniami konstrukcji podczas próbnego obciążenia. Przeprowadzono weryfikację obliczeń projektowych i zaprojektowano próbne obciążenie. Podsumowano wyniki analizy i badań. Dodatkowo opisano nową, stalową konstrukcję...
-
Timber-frame house resistant to dynamic loads - analysis of wall panel filled with polyurethane foam
PublikacjaThe present study shows the experimentally and numerically determined response of a single timber-frame house wall panel filled with polyurethane (PU) foam under dynamic loads. The harmonic tests were conducted for the following frequencies: 0.5 Hz, 1.0 Hz, 2.0 Hz and 5.0 Hz for various values of the specified displacement. Based on the results of the comparison between the experimental tests and the numerical analyses, the numerical...
-
Modele numeryczne uwzględniające tarczową pracę pokrycia dachowego z blach trapezowych
PublikacjaW artykule porównano wybrane sposoby uwzględniania w modelowaniu numerycznym tarczowej pracy pokrycia dachowego z blachy trapezowej, możliwe do zrealizowania w programie Autodesk Robot Structural Analysis Professional 2015, w celu oceny słuszności stosowania ich do obliczeń konstrukcji nośnej współpracującej z poszyciem z blachy trapezowej. Analizy przeprowadzono dla pojedynczej przepony. Za pomocą powłokowych elementów skończonych...