Filtry
wszystkich: 1138
wybranych: 831
Wyniki wyszukiwania dla: REINFORCED CONCRETE TANK
-
Effect of polymer fibres reinforcement on selected properties of asphalt mixtures
PublikacjaThe paper presents selected results of the research program concerning fibre reinforced asphalt concrete. Aramid-polyalphaolefin fibres was used in this study. Selected properties responsible for low temperature cracking and resistance to permanent deformation are presented in this paper. Low temperature cracking susceptibility was evaluated with the results obtained from bending test of rectangular beams with constant rate of...
-
Load capacity of steel-aluminium brackets under static and cyclic laboratory tests
PublikacjaThe aim of the research is the laboratory investigation of steel-aluminium brackets employed to fasten lightweight curtain walls to building facilities. Static pressure, suction forces, and cyclic loads parallel to end plates (horizontal – to simulate wind influence) were applied in the study. The steel-aluminium brackets were tested on a reinforced concrete substrate made of C30/37 concrete class to simulate the real working conditions....
-
Experimental Study of Dapped-End Beams Subjected to Inclined Load
PublikacjaThis paper presents the results of an experimental investigation of the reinforced concrete (RC) dapped-end beams loaded with inclined forces, compared to identical ones loaded with vertical forces only. Such a load may occur in, for example, Gerber's joints or in dapped-end beams supported on corbels, where the vertical gravitation force is additionally completed with horizontal forces caused by temperature differences, shrinking,...
-
Dome over the Gdynia seaport building
PublikacjaThe paper presents the description of structure and the selected problems of the technical condition, as well as the strength analysis of the thin-walled reinforced concrete shell which has been making a covering of the main hall of the Gdynia Seaport Building through the last 80 years. The rectangle projection of four single curvature shells of the dome was shaped out of mutual perpendicular intersection of two cylindrical shells. The...
-
Schemat powstawania rys na przykładzie osiowo rozciąganego pręta żelbetowego
PublikacjaW artykule przedstawiono w sposób schematyczny ideę powstawania kolejnych rys w konstrukcjach żelbetowych na przykładzie osiowo rozciąganego pręta. Opisano początkowy oraz końcowy stan zarysowania. Wyprowadzono wzór na szerokość rysy. Przedstawiono interpretację geometryczną rys dla fazy początkowego zarysowania oraz efekt tension stiffening na przykładzie elementu osiowo rozciąganego. Przedstawiono przykładowe obliczenia miary...
-
Impact response of two-layered grouted aggregate fibrous concretecomposite under falling mass impact
PublikacjaTwo-layered Grouted Aggregates Fibrous Concrete Composite (TGAFCC) is a new category concrete which became popular recently and attracted the attention of researchers globally. Recent studies indicated that TGAFCC has notable improvement in mechanical properties, which has been sufficiently documented. However, the impact behaviour of TGAFCC when combined with Glass Fibre Mesh (GFM) and Textile Fibre Mesh (TFM) is still unexplored....
-
Soil-structure interaction effects on modal parameters of office buildings with different number of stories
PublikacjaThe paper summarizes the results of a numerical investigation designed to study the soil-structure interaction effects on modal parameters of three office buildings. The reinforced-concrete 4-storey, 8-storey, and 12-storey office buildings, each with additional two levels of embedded basements, represent low, medium, and high-rise structures, respectively. In order to conduct this research, detailed finite-element structure models...
-
Non-Linear Analysis of Inter-Story Pounding between Wood-Framed Buildings during Ground Motion
PublikacjaPounding between adjacent buildings during ground motion may result in structural damage or lead to total destruction of structures. The research on the phenomenon has recently been much advanced; however, the analyses have been carried out only for concrete, steel, and masonry structures, while pounding between wooden buildings has not been studied so far. The aim of this paper is to show the results of detailed non-linear seismic...
-
Retrievable strain measuring system in screw displacement piles - readings and results interpretation problems
PublikacjaStatic load tests on foundation piles are generally carried out in order to determine load – displacement characteristic of the pile. For more detailed information, e.g. force distribution along the shaft, load transfer mechanism and characteristics of soil-structure interaction (unit resistance curves t-z, q-z) additional pile instrumentation is required. Most popular techniques focus on direct concrete strain measurements and...
-
Shear Cap Size Selection Method Based on Parametric Analysis of ACI-318 Code and Eurocode 2 Standard
PublikacjaThe scope of the paper is to propose a method for determining the size of shear caps in a slab–column-connections-reinforced concrete structure. Usually, shear heads are used to enhance slab–column connection, especially when the transverse reinforcement does not give the required punching shear load capacity. The dimensions of the shear head should provide the punching shear resistance of the connection inside and outside the...
-
Wpływ zbrojenia polimerowymi włóknami rozproszonymi na wybrane właściwości mieszanek mineralno-asfaltowych
PublikacjaW artykule przedstawiono wybrane wyniki badań mieszanek mineralno-asfaltowych zbrojonych polimerowymi włóknami rozproszonymi. Ocenie poddano mieszankę włókien zbrojących aramidowo-poliolifenowych pod kątem wpływu ich zastosowania na właściwości niskotemperaturowe i odporności na deformacje trwałe mieszanek mineralno-asfaltowych. Właściwości niskotemperaturowe oceniano na podstawie testu zginania próbek belkowych oraz na podstawie...
-
Building Information Modelling as an opportunity and risk for stakeholders involved in construction investment process
PublikacjaThe requirements to apply Building Information Modelling (BIM) in public investments worldwide are currently very high. Significant interest (sometimes formulated also as a requirement) in BIM technology can be observed also among private investors. Design technology that applies BIM is supported by many private investors due to its numerous advantages. A growing group of construction designers (steel, concrete and reinforced concrete...
-
Tubular House - Form Follows Technology, Concrete Shell Structure with Inner Thermal Insulation
PublikacjaThe aim of this paper is the theoretical analysis of the possibilities and limitations of using an unconventional technology and the original architectural form stemming from it – the building with external construction and internal insulation. In Central European climatic conditions, the traditional solution for the walls of heated buildings relies on using external thermal insulation. This stems from building physics: it prevents...
-
Models of Structures in Didactics
PublikacjaThe final aim of teaching students subjects, such as structural mechanics, reinforced concrete, and steel structures is to teach them how structures work in a given building as well as to provide them with skills enabling them to calculate and design structures. The behavioral model of the structure, contrary to the architectural model, which focuses mainly on the external form of the building, shows workings from both the static...
-
Optimized Computational Intelligence Model for Estimating the Flexural Behavior of Composite Shear Walls
PublikacjaThis article presents a novel approach to estimate the flexural capacity of reinforced concrete-filled composite plate shear walls using an optimized computational intelligence model. The proposed model was developed and validated based on 47 laboratory data points and the Transit Search (TS) optimization algorithm. Using 80% of the experimental dataset, the optimized model was selected by determining the unknown coefficients of...
-
Numerical Study on Seismic Response of a High-Rise RC Irregular Residential Building Considering Soil-Structure Interaction
PublikacjaThe objective of the present study is to investigate the importance of soilstructure interaction effects on the seismic response of a high-rise irregular reinforced-concrete residential building. In order to conduct this research, a detailed three-dimensional structure model was subjected to various earthquake excitations, also including a strong mining tremor. Soil-foundation flexibility was represented using the spring-based...
-
Influence of the Shear Cap Size and Stiffness on the Distribution of Shear Forces in Flat Slabs
PublikacjaThe scope of this paper is to investigate analytically and numerically the influence of shear cap size and stiffness on the distribution of shear forces in flat slabs in a slab–column-connections-reinforced concrete structure. The effect of support (shear cap) stiffness on the calculation of the length of the shear control perimeter according to the available methods is presented. Based on the analysis, the authors indicate in...
-
A HISTORICAL BUILDING'S RESTORATION IN THE CONSTRUCTIONAL ASPECT ON THE EXAMPLE OF A BUILDING LOCATED IN POLAND
PublikacjaObjects of cultural heritage are an extremely important element in the proper functioning of the social life. They provide information on our ancestors' actions, as well as shape our culture and social awareness. It is important for the historical objects to provide those information accurately, that is without any unnecessary human intervention over the years of the monument's existence. However, it is not always possible due...
-
Wave Method for Structural Health Monitoring: Testing Using Full-Scale Shake Table Experiment Data
PublikacjaAn algorithm of the wave method for structural health monitoring (SHM) is tested and calibrated using shake table experiment data of a full-scale, seven-story, reinforced-concrete building slice. The method is based on monitoring changes in the velocity of waves propagating vertically through the structure, identified by least-squares (LSQ) fit of beam models. The experiment was conducted by a team from the University of California,...
-
EVALUATION OF 3D MODEL OF REBAR FOR QUANTITATIVE PARAMETERS
PublikacjaThe construction industry practices and processes are evolving constantly, and with the emergence of Industry 4.0, the use of technologies is expanding. Construction progress monitoring is an essential project lifecycle process; project success and timely completion are linked with effective progress monitoring operations and adopted tools. In the domain of automated construction progress monitoring, 3D modeling techniques have...
-
Introducing a Computational Method to Retrofit Damaged Buildings under Seismic Mainshock-Aftershock Sequence
PublikacjaRetrofitting damaged buildings is a challenge for engineers, since commercial software does not have the ability to consider the local damages and deformed shape of a building resulting from the mainshock record of an earthquake before applying the aftershock record. In this research, a computational method for retrofitting of damaged buildings under seismic mainshock-aftershock sequences is proposed, and proposed computational...
-
Nonlinear numerical simulation of earthquake-induced pounding between timber frame buildings
PublikacjaEarthquakes may induce serious dynamic loads acting on buildings, which can lead to damage or even destruction of the whole structure. In densely populated areas, it is quite common that buildings are located very close one to another which can result in pounding between them during ground motions. Due to the environmental awareness, multi-story timber frame buildings are gaining popularity and therefore there is a need to investigate...
-
Seismic damage diagnosis in adjacent steel and RC MRFs considering pounding effects through improved wavelet-based damage-sensitive feature
PublikacjaThis paper aims to propose complex Morlet (cmorfb-fc) wavelet-based refined damage-sensitive feature (rDSF) as a new and more precise damage indicator to diagnose seismic damages in adjacent steel and Reinforced Concrete (RC) Moment Resisting Frames (MRFs) assuming pounding conditions using acceleration responses. The considered structures include 6- and 9-story steel and 4- and 8-story RC benchmark MRFs that are assumed to have...
-
Linear viscoelastic transversely isotropic model based on the spectral decomposition of elasticity tensors
PublikacjaThe linear viscoelasticity is still a useful model in the engineering for studying the behavior of materials loaded with different loading rates (frequencies). Certain types of materials reveal also an anisotropic behavior: fiber reinforced composites, asphalt concrete mixtures, or wood, to name a few. In general, researchers try to identify experimentally the dependence of engineering constants like: directional Young’s moduli...
-
Fragility analysis of structural pounding between adjacent structures arranged in series with various alignment configurations under near‑field earthquakes
PublikacjaA major cause of local to total damages is related to structural pounding in a large number of past earthquakes. In general, these collisions take place as a result of differences in the dynamic characteristics of the colliding structures. To acquire a better perception of the behavior of structures, in this paper, three structures featuring different heights are modeled in series and with various configurations next to each other...
-
Results of acoustic emission tests of corrosion protection degree of ship steel tanks covered by means of protective coatings (Phase I)
PublikacjaThis paper presents methods and results of the 1st series of tests of acoustic emission (AE) signals, aimed at assessing degree of corrosion protection of a tank made of hull structural steel, protected by means of a protective coating combined from polyurethane layer and concrete filler. The tests were carried outin compliance with a method specially elaborated for application to the work in question. In the method were used requirements...
-
Seismic damage diagnosis in adjacent steel and RC MRFs considering pounding effects through improved wavelet-based damage-sensitive feature
PublikacjaThis paper aims to propose complex Morlet (cmorfb-fc) wavelet-based refined damage-sensitive feature (rDSF) as a new and more precise damage indicator to diagnose seismic damages in adjacent steel and Reinforced Concrete (RC) Moment Resisting Frames (MRFs) assuming pounding conditions using acceleration responses. The considered structures include 6- and 9-story steel and 4- and 8-story RC benchmark...
-
Doraźna nośność słupów o przekroju kołowym z rur FRP wypełnionych betonem Badania, teoria, obliczanie
PublikacjaPraca ma charakter monografii opisującej aktualny stan wiedzy z zakresu badań, teorii i projektowania słupów CFFT (concrete-filled fiber-reinforced polymer tube). Celem prowadzonych przez autora prac studialnych i badań własnych, w tym eksperymentalnych, jest szczegółowa analiza doraźnej nośności i zachowania się słupów CFFT poddanych ściskaniu osiowemu i mimośrodowemu. W pierwszym rozdziale wyjaśniono motywację autora do podjęcia...
-
The propagation of the waves in the CTO S.A. towing tank
PublikacjaThe paper presents the results of research focused on the wave propagation in the CTO S.A. deepwater towing tank. In the scope of paper, the wavemaker transfer function was determined for regular waves, based on the Biésel Transfer Function and further for irregular waves, based on Hasselman model of nonlinear energy transfer. The phenomena: wave damping, wave breakdown and wave reflection, were measured, analyzed and mathematically...
-
Modelling, Simulation and Optimization of the Wavemaker in a Towing Tank
PublikacjaThe paper analyses the problem of experimental identification (frequency response), modelling and optimization of the towing tank wavemaker in the Scilab/Xcos environment. The experimental identification of the objects (the towing tank wavemaker placed in the hydrodynamic laboratory of the CTO S.A. Ship Design and Research Centre (CTO)) and the implementation of the models in the simulation environment, enable to perform: 1. tuning...
-
Reliability estimation of underground horizontal fuel tank limit states
PublikacjaFuel tanks are designed with regard to standard loads and operating conditions. The investigations of the paper show the impact of such factors as tank corrosion and other means on the variation of stress fields and deformation of the underground horizontal tank shell. The introduction of probabilistic methods allows for structural reliability assessment. While the computational time of the entire tank FEM model is high, the preliminary...
-
Deformations of the steel schell of a vertical cylindrical tank caused by underpressure
PublikacjaUnderpressure in a tank with a fixed roof may arise in the final stage of its construction as well as during its usage. This article presents stages of deformations of the tank shell and their development from the occurrence of the first deformation to either removal of the causes of underpressure or cracking of the steel shell.
-
Composite as a Material of the Future in the Era of Green Deal Implementation Strategies
PublikacjaComposite materials have become synonymous with modernity, desired in nearly every aspect of our daily lives, from simple everyday objects to sanitary facilities, pipelines, the construction of modern sewer networks, their renovation, water supply, and storage reservoirs, to complex structures—automotive, planes, and space science. Composites have seen a considerable rise in attention owing to their characteristics, durability,...
-
Experimental study on earthquake-induced pounding between steel structures
PublikacjaPounding between adjacent structures has been repeatedly observed during major earthquakes. The phenomenon may cause some local damage at the points of interactions, it may also lead to substantial destruction, permanent deformations or total collapse of colliding structures. The effects of earthquake-induced structural pounding have been studied for more than three decades now. However, most of the studies concerned masonry as...
-
Digital Control System of the Wavemaker in the Towing Tank
PublikacjaThe paper describes a digital control system of the rigid flap wavemaker in a towing tank in CTO S.A. Ship Design and Research Centre. The control system is based on an 8-bit AVR microcontroller and consists of two cascading PID controllers. The digital system replaced the previous analogue system from 1974 and has been integrated with the existing sensors and actuators of the wavemaker. The new control system allows to obtain...
-
Generation and Propagation of Nonlinear Waves in a Towing Tank
PublikacjaThe paper presents the results of the research focused on linear and nonlinear wave generation and propagation in a deepwater towing tank equipped with a single flap-type wavemaker of variable draft. The problem of wave generation and propagation has been theoretically formulated and solved by applying an analytical method; linear and nonlinear solutions were obtained. The linear solution has been verified experimentally. The...
-
Synthesis of a state feedback controller for an averaging tank with variable filling
PublikacjaIn paper, a nonlinear averaging tank with variable filling is considered. The main purpose of this research work was the modelling and control system synthesis of an averaging tank. The control objectives included ensuring stability and zero steady-state error of the system and achieving settling time as short as possible, while maintaining a minimal overshoot. In order to achieve the intended purpose, firstly a mathematical model...
-
Using differential pressure sensor to measure nitrous oxide level in a tank
PublikacjaA method for measuring the level of liquid nitrous oxide oxidizer in a hybrid rocket motor oxidizer tank is proposed. Presented approach is more accurate than the most commonly used method of this measurement, which employs weighting of the whole sounding rocket or an oxidizer tank. In our solution we use a differential pressure sensor to measure the change of pressure at the bottom of an oxidizer tank in comparison to the pressure...
-
Analysis of Impulse Responses Measured in Motion in a Towing Tank
PublikacjaThe growing interest in developing autonomous underwater vehicles (AUVs) and creating underwater sensor networks (USNs) has led to a need for communication tools in underwater environments. For obvious reasons, wireless means of communication are the most desirable. However, conducting research in real conditions is troublesome and costly. Moreover, as hydroacoustic propagation conditions change very significantly, even during...
-
Analysis of Impulse Responses Measured in Motion in a Towing Tank
PublikacjaThe growing interest in developing autonomous underwater vehicles (AUVs) and creating underwater sensor networks (USNs) has led to a need for communication tools in underwater environments. For obvious reasons, wireless means of communication are the most desirable. However, conducting research in real conditions is troublesome and costly. Moreover, as hydroacoustic propagation conditions change very significantly, even during...
-
Design of three control algorithms for an averaging tank with variable filing
PublikacjaAn averaging tank with variable filling is a nonlinear multidimensional system and can thus be considered a complex control sys-tem. General control objectives of such object include ensuring stability, zero steady state error and achieving simultaneously shortest possible settling time and minimal overshoot. The main purpose of this research work was the modelling and synthesis of three control systems for an averaging tank. In...
-
Identification of dynamic parameters in the context of diagnostics of steel tank with different level of liquid.
PublikacjaThe paper presents an experimental study to identify the dynamic parameters of a water-filled tank model. The experimental modal analysis approach involving the excitation at one point of the structure and acquisition of vibra tions at selected points distri buted over the tank surface allowed to determine the resonance frequencies, mode shapes and damping ratios. The main aim of the research was to examine the influence of...
-
Probabilistic estimation of diverse soil condition impact on vertical axis tank deformation
PublikacjaThe calculations of fuel tanks should take into account the geometric imperfections of the structure as well as the variability of the material parameters of the foundation. The deformation of the tank shell can have a significant impact on the limit state of the structure and its operating conditions. The paper presents a probabilistic analysis of a vertical-axis, floating-roof cylindrical shell of a tank with a capacity of 50000...
-
CONTROL OF THE WAVES IN A TOWING TANK WITH THE USE OF A BLACK-BOX MODEL
PublikacjaThe paper describes an adaptive control system of the waves, implemented in the Ship Design and Research Centre, CTO S.A. The purpose of generating the waves in the towing tank is the modelling of the environmental conditions during hydrodynamic model tests. The tests are performed on scale models of towed or free running ships, anchored structures like oil rigs or bottommounted structures, e.g. wind turbines. In the towing tank...
-
Justifying the prolongation of the service life of the bearing structure of a tank car when using Y25 bogies
PublikacjaThis paper substantiates the use of Y25 bogies under tank cars in order to prolong their service life. The reported study has been carried out for a tank car with rated parameters, as well as the actual ones, registered during full-scale research. Mathematical modeling was performed to determine the basic indicators of the tank car dynamics. The differential equations of motion were solved by a Runge-Kutta method using the Mathcad...
-
Diagnosis of Damage in a Steel Tank with Self-Supported Roof through Numerical Analysis
PublikacjaThe safety of civil engineering structures is one of the most important issues of building industry. That is why the assessment of the damage-involved structural response has recently become of major concern to engineers. Among a number of different approaches to diagnosis of damage, the method of measuring the changes in natural frequencies is considered to be one of the most effective indicators of global damage. From the practical...
-
Fuzzy Control of Waves Generation in a Towing Tank
PublikacjaThis paper presents the results of research related to the transformation of electrical energy into potential and kinetic energy of waves generated on the water surface. The waves are generated to model the environmental conditions for the needs of the model tests. The model tests are performed on model-scale objects to predict the features of full-scale maritime objects. It is done to improve human safety and the survivability...
-
Developing Methodology for Model Tests of Floating Platforms in Low -Depth Towing Tank
PublikacjaThe paper presents two different methods of physical modeling of semi-submersible platform mooring system for research in low depth towing tank. The tested model was made in the scale of 1:100 resembling the "Thunder Horse" platform moored in the Gulf of Mexico at a depth of 1,920 m. Its mooring system consisted of 16 semi-taut mooring lines (chain-wire-chain) spaced starshape and attached at the bottom to suction piles. The tests...
-
Environmemtal Degradation of Ramie Fibre Reinforced Biocomposites
PublikacjaThe estimation of environmental degradibility of different fibre reinforced biocomposites in Baltic sea and in compost with activated sludge under natural conditions is the subject of this paper. Two types of biocomposites, ramie fibre/ecoflex and ramie fibre/cellulose nanofibre reinforced corn starch resin, were studied.It was demonstrated that the biocomposites with natural fibre of ramie were degraded in compost faster than...
-
Poroelastic Road Surfaces - State of The Art
PublikacjaPoroelastic Road Surfaces (PERS) constitute a specific group of pavements containing a great amount of crumbled rubber. In most cases rubber aggregate constitutes about 20% of the mixture (by weight) and a polyurethane resin is used as a binder. As a result, PERS is characterized by a much higher elasticity than asphalt and a high porosity typical for drainage pavements. Due to this, tire/road noise is greatly reduced and on top...