Wyszukiwarka
Filtry
wszystkich: 95
wybranych: 88
Filtry wybranego katalogu
Wyniki wyszukiwania dla: CONTACT ANGLE
-
Measurements of droplet contact angle of nanofluids
PublikacjaPrzedstawiono wyniki pomiarów kąta zwilżania trzech nanocieczy: woda-Al2O3, woda-TiO2 oraz woda-Cu. Koncentracja nanocząstek wynosiła: 0.01%, 0.1% oraz 1%. Pomiary przeprowadzono dla podłoża szklanego, aluminiowego i ze stali nierdzewnej. Kąt zwilżania mierzono za pomocą goniometru, a także na podstawie zdjęć wykonanych za pomocą kamery cyfrowej.
-
Determination of binder-aggregate adhesion by contact angle measurement
PublikacjaThe key factor in asphalt pavement durability, especially in the presence of water, is adhesion of the bituminous binder to mineral aggregates. There are currently no standard laboratory test procedures that can quickly and accurately measure the strength of the interaction (bond) between the binder and aggregate. In this regard, to evaluate the adhesion force measurements based on the contact angle between the binder and the aggregate...
-
INFLUENCE OF SURFACE CURVATURE ON SESSILE DROPLET CONTACT ANGLE OF NANOFLUIDS
PublikacjaThis paper deals with change in contact angle of droplets of three nanofluids, i.e. water-Al2O3, water-TiO2 and water-Cu. Nanoparticles were tested at the concentration of 0.01%, 0.1%, and 1% by weight. Although dispersants were not used to stabilize the suspension, the solutions tested exhibited satisfactory stability. Ultrasonic vibration was used in order to stabilise the dispersion of the nanoparticles. Experimental measurements...
-
Contact angle of the ferronanofluid and influence of the magnetic field on the drying droplet
Publikacja -
Influence of concentration on contact angle of water-Cu nanofluid on glass substrate
PublikacjaIn the paper the results of an experimental investigation of influence of nanoparticle concentration on contact angle of water-Cu nanofluid on glass substrate have been presented. Nanoparticles were tested at the concentration of 0.01%, 0.1%, and 1% by weight. In the present study copper was applied as nanoparticle while distilled, deionized water was used as a base fluid. The mean diameter of nanoparticle is estimated to be 50...
-
Evaluation of fouling potential of nanofiltration membranes based on the dynamic contact angle measurements
Publikacja -
Sessile droplet contact angle of water–Al2O3, water–TiO2 and water–Cu nanofluids
PublikacjaThis work presents measurements of the contact angle of sessile droplets for three nanofluids, i.e. water–Al2O3, water–TiO2 and water–Cu. The plates made of glass, anodized aluminium and stainless steel of different roughness served as substrates. Ultrasonic vibration was used for 30–60 min in order to stabilise the dispersion of the nanoparticles. Nanoparticles were tested at the concentration of 0.01%, 0.1%, and 1% by weight....
-
SESSILE DROPLET CONTACT ANGLE OF WATER-Al2O3, WATER-TiO2 AND WATER-Cu NANOFLUIDS
PublikacjaThe goal of the present work was the experimental determination of the contact angle of droplets of three nanofluids on various substrates. Of particular interest was effect of nanoparticle concentration on droplet contact angle.
-
The effect of boiling in a thermosyphon on surface tension and contact angle of silica and graphene oxide nanofluids
Publikacja -
New Simple and Robust Method for Determination of Polarity of Deep Eutectic Solvents (DESs) by Means of Contact Angle Measurement
PublikacjaThe paper presents a new method for evaluating the polarity and hydrophobicity of deep eutectic solvents (DESs) based on the measurement of the DES contact angle on glass. DESs consisting of benzoic acid derivatives and quaternary ammonium chlorides–tetrabutylammonium chloride (TBAC) and benzyldimethylhexadecylammonium chloride (16-BAC)—in selected molar ratios were chosen for the study. To investigate the DESs polarity, an optical...
-
New Simple and Robust Method for Determination of Polarity of Deep Eutectic Solvents (DESs) by Means of Contact Angle Measurement
Publikacja -
Rozmyty system wnioskowania do oszacowania maksymalnego naprężenia kontaktowego na powierzchni panewki endoprotezy stawu biodrowego w zależności od kąta Wiberga i masy ciała pacjenta = Fuzzy reasoning system for maximal contact stress estimation on acetabular surface in hip endoprosthesis based on Wiberg angle and weight of patient
PublikacjaPrzedstawiono możliwość wykorzystania systemu rozmytego, który wykorzystując rozumowanie przybliżone określa maksymalne naprężenie kontaktowe na powierzchni przenoszenia obciążeń panewki endoprotezy stawu biodrowego, biorąc pod uwagę kąt Wiberga oraz masę ciała pacjenta.
-
Wettability of Horizontal Stainless Steel Tube by Nanofluid Droplets
PublikacjaThe goal of the present work was the experimental determination of the contact angle of three nanofluids, i.e. water-Al2O3, water-Cu and water-TiO2 on horizontal stainless steel tube of 1.6 mm OD. Of particular interest was the effect of nanoparticle concentration (0.01%, 0.1%, and 1% by weight) on droplet contact angle.
-
Wettability of Horizontal Stainless Steel Tube by Nanofluid Droplets
PublikacjaThe goal of the present work was the experimental determination of the contact angle of three nanofluids, i.e. water-Al2O3, water-Cu and water-TiO2 on horizontal stainless steel tube of 1.6 mm OD. Of particular interest was the effect of nanoparticle concentration (0.01%, 0.1%, and 1% by weight) on droplet contact angle.
-
Leaf wettability and plant surface water storage for common wetland species of the Biebrza peatlands (northeast Poland)
PublikacjaWetlands play a crucial role in buffering the effects of climate change. At the same time, they are one of the most endangered ecosystems on the globe. The knowledge of the water cycle and energy exchange is crucial for the practical preservation and exploiting their capabilities. Leaf wettability is an important parameter characterising the plant's ability to retain water on its surface, and is linked to the ecosystems' hydrological...
-
The effect of the exposure-in-oil on the contact of the polymers forming sliding layers in hydrodynamic bearings. Wpływ ekspozycji w oleju na kąt zwilżania polimerów stosowanych na warstwy ślizgowe w łożyskach hydrodynamicznych.
PublikacjaPolimery stosowane jako warstwy ślizgowe w hydrodynamicznych łożyskach wzdłużnych to zazwyczaj tworzywa termoplastyczne charakteryzujące się relatywnie wysokimi wartościami kątów zwilżania w porównaniu z metalami. Metale, w tym również Babbitt czy inne stopy łożyskowe, cechują niskie wartości kątów zwilżania. Im niższy kąt, tym powierzchnia lepiej się zwilża. Tworzywa sztuczne wykorzystywane w węzłach tribologicznych mających zapewnić...
-
The effect of surfactants mixtures composition on wetting of different solid materials
PublikacjaThe wetting properties of surfactants mixtures were investigated. Three types of compounds were used: nonionic gemini α, α'-[2,4,7,9-tetramethyl-5-decyne-4,7-diyl]bis[ω-hydroxyl-olioxyethylene] (S-10), anionic sodium dodecyl sulphates (SDS) and cationic dodecyl trimethyl ammonium bromide (DTAB). The materials used in wetting experiments were steel and methyl polymethacrylate. These materials differ...
-
Comparative 3D DEM simulations of sand–structure interfaces with similarly shaped clumps versus spheres with contact moments.
PublikacjaThree-dimensional simulations of a monotonic quasi-static interface behaviour between initially dense cohesionless sand and a rigid wall of different roughness during tests in a parallelly guided direct shear test under constant normal stress are presented. Numerical modelling was carried out by the discrete element method (DEM) using clumps in the form of convex non-symmetric irregularly shaped grains. The clumps had an aspect...
-
AUGMENTATION OF THE CRITICAL HEAT FLUX IN WATER-Al2O3, WATER-TiO2 AND WATER-Cu NANOFLUIDS
PublikacjaThe main aim of the proposed study is therefore recognition of the phenomena accompanying nucleate boiling crisis of selected nanofluids during boiling on horizontal tubes of various outside diameters. Of particular interest is impact of contact angle and tube diameter on the value of critical heat flux. The results obtained should give more light on the nature of nucleate boiling crisis and will serve as a basis for future theoretical...
-
Influence of geometrical and operational parameters on tooth wear in the working mechanism of a satellite motor
PublikacjaThis article describes the phenomena affecting the wear of the rotor of the working mechanism in a hydraulic satellite motor. The basic geometrical relationships that allow the calculation of the coordinates of the points of contact between the satellite and the rotor and the curvature are presented. A method for calculating the number of contacts of the satellite teeth with the rotor teeth and of the satellite teeth with the curvature...
-
Effects of electrophoretic deposition times and nanotubular oxide surfaces on properties of the nanohydroxyapatite/nanocopper coating on the Ti13Zr13Nb alloy
PublikacjaLoad-bearing implants are developed with a particular emphasis placed on an application of ceramic hydroxyapatite coatings in order, to enhance the bioactivity of titanium implants and to shorten the healing time. Therefore, thin, fully crystalline coatings that are, highly adhesive, hydrophilic and demonstrating antibacterial properties are ly looked for. The aim of this research was to develop and characterize the properties...
-
Study of Nanohydroxyapatite Coatings Prepared by the Electrophoretic Deposition Method at Various Voltage and Time Parameters
PublikacjaThe aim of the work is to compare the properties of nanohydroxyapatite coatings obtained using the electrophoretic deposition method (EDP) at 10 V, 20 V, and 30 V, and with deposit times of 2 and 5 min. The primary sedimentation was used to minimize the risk of the formation of particle agglomerates on the sample surface. Evaluation of the coating was performed by using a Scanning Electron Microscope (SEM), Energy-Dispersive Spectroscopy...
-
Sustainable Chemically Modified Mater-Bi/Poly(ε-caprolactone)/Cellulose Biocomposites: Looking at the Bulk through the Surface
PublikacjaSustainable polymer composites are progressively under development in a technological paradigm shift from "just use more and more" to "convert into value-added products". The bio-based blends based on Mater-Bi bio-plastic (A) and poly(ε-caprolactone) (B), at a weight ratio of 70:30 (A:B) were developed, followed by the addition of UFC100 cellulose (C) filler to yield 70/30 (w/w) (A:B)/C sustainable biocomposites. The effects of...
-
Modeling protein structures with the coarse-grained UNRES force field in the CASP14 experiment
PublikacjaThe UNited RESidue (UNRES) force field was tested in the 14th Community Wide Experiment on the Critical Assessment of Techniques for Protein Structure Prediction (CASP14), in which larger oligomeric and multimeric targets were present compared to previous editions. Three prediction modes were tested (i) ab initio (the UNRES group), (ii) contact-assisted (the UNRES- contact group), and (iii) template-assisted (the UNRES-template...
-
Wpływ wysokiej osteotomii piszczelowej na mechanikę stawu kolanowego
PublikacjaW rozprawie podjęto próbę weryfikacji wpływu zabiegu chirurgicznego wysokiej osteotomii piszczelowej na mechanikę stawu kolanowego. Po wykonanym przeglądzie literatury, postawiono trzy hipotezy, które poddano weryfikacji na drodze badań numerycznych. Otrzymane wyniki zwalidowano poprzez badania nacisków powierzchniowych występujących w stawach kolanowych świni domowej, prowadzonych na maszynie do jednoosiowego ściskania. Praca...
-
Surface modification of PMMA polymer and its composites with PC61BM fullerene derivative using an atmospheric pressure microwave argon plasma sheet
PublikacjaThis paper presents the results of experimental investigations of the plasma surface modification of a poly(methyl methacrylate) (PMMA) polymer and PMMA composites with a [6,6]-phenyl-C61-butyric acid methyl ester fullerene derivative (PC61BM). An atmospheric pressure microwave (2.45 GHz) argon plasma sheet was used. The experimental parameters were: an argon (Ar) flow rate (up to 20 NL/min), microwave power (up to 530 W), number...
-
Investigation of the Effects of Tool Positioning Factors on Peak Temperature in Dissimilar Friction Stir Welding of AA6061-T6 and AA7075-T6 Aluminum Alloys
PublikacjaAmong the emerging new welding techniques, friction stir welding (FSW) is used frequently for welding high-strength aluminum alloys that are difficult to weld by conventional fusion-welding techniques. This paper investigated the effects of tool-positioning factors on the maximum temperature generated in the dissimilar FSW joint of AA6061-T6 and AA7075-T6 aluminum alloys. Three factors of plunge depth, tool offset, and tilt angle...
-
Sustainable chemically modified poly(butylene adipate-co-terephthalate)/thermoplastic starch/poly(ε-caprolactone)/cellulose biocomposites: looking at the bulk through the surface
PublikacjaSustainable polymer composites (or biocomposites) based on renewable and green polymers are progressively under development in a technological paradigm shift from “just use more and more” to “convert into value-added products”. Therefore, significant efforts should focus not only on their reduced environmental impact but also on maximizing their performance and broadening their application range. Herein, the bio-based blends based...
-
Superhydrophobic and superoleophilic melamine sponges impregnated with deep eutectic solvents for oil spill cleanup
PublikacjaThe extensive extraction of oil from the bottom of seas and oceans and its transportation by tankers increase the risk of potential environmental disasters associated with hydrocarbon fractions entering water reservoirs. Therefore, this paper presents the preparation of a simple impregnation of a melamine sponge with deep eutectic solvents (DES), which can be obtained from natural sources, including coconut oil, palm kernel oil,...
-
Defected Ag/Cu-MOF as a modifier of polyethersulfone membranes for enhancing permeability, antifouling properties and heavy metal and dye pollutant removal
PublikacjaIn this study, a novel bimetallic metal-organic framework (MOF) i.e. Ag/Cu-MOF was synthesized using a solvothermal method and later incorporated at different concentrations (0.1–2 wt%) using a phase inversion method for modification and antifouling property improvement of polyethersulfone (PES) membranes. The resulting Ag/Cu-MOF characteristics were investigated using different techniques, such as FTIR, XRD, FE-SEM and EDX. The...
-
Effects of solution composition and electrophoretic deposition voltage on various properties of nanohydroxyapatite coatings on the Ti13Zr13Nb alloy
PublikacjaThe purpose of the research was to establish the influence of the solution composition and the electrophoretic deposition voltage on the coating homogeneity and thickness, nanohardness, adhesion, corrosion resistance and wettability. The Ti13Zr13Nb alloy was coated by the electrophoretic technique with hydroxyapatite in a solution containing 0.1, 0.2 or 0.5 g nanoHAp in 100 mL of suspension and at voltage 15, 30 or 50 V. The scanning...
-
Susceptibility to Degradation in Soil of Branched Polyesterurethane Blends with Polylactide and Starch
PublikacjaA very important method of reducing the amount of polymer waste in the environment is the introduction to the market of polymers susceptible to degradation under the influence of environmental factors. This paper presents the results of testing the susceptibility to degradation in soil of branched polyesterurethane (PUR) based on poly([R,S]-3-hydroxybutyrate) (R,S-PHB), modified with poly([D,L]-lactide) (PLA) and starch (St). Weight...
-
Biological and mechanical research of titanium implants covered with bactericidal coating
PublikacjaThe paper concerns the biological and mechanical properties of titanium implants with an antibacterial coating. The Ti13Zr13Nb alloy samples were coated with hydroxyapatite (HAp) coatings using the electrophoretic deposition technique (EPD). Subsequently, the surface of the samples was modified with silver, copper, and nickel nanoparticles by the immersion method. Different titanium sample types (i.e. HAp-only and nanometals-enriched...
-
Research of chitosan coatings deposited by electrophoretic deposition method at various voltage and time parameters
PublikacjaThe aim of this research is to estimate the electrophoretic deposition main parameters, such as voltage and time duration, that will provide optimal characteristics of the surface layer. Chitosan coatings were synthesized on biomedical Ti13Zr13Nb alloys at 20 V and 30 V and with deposit times of 2min, 5 min, 10 min, and 15 min. Evaluation of the coating was performed by using Scanning Electron Microscope (SEM), Energy-Dispersive...
-
The study of structure and surface morphology of lithium titanate sol-gel derived thin films
PublikacjaIn this paper the structure and the surface morphology of lithium titanate (LTO) thin films are presented. Nanocrystalline thin films were prepared by sol–gel method. To examine the influence of the annealing time on as-prepared films crystallization, the coatings were heated at different temperatures in the range of 500 °C–600 °C for 10, 20, 40 and 80 h. The structure of the obtained material was investigated using the X-ray diffraction...
-
Hybrid cross-linked chitosan/protonated-proline:glucose DES membranes with superior pervaporation performance for ethanol dehydration
PublikacjaThis work explores a protonated L-proline:glucose (molar ratio 5:1) deep eutectic solvent (DES) in fabricating biopolymer membranes utilizing chitosan (CS). Initially, the miscibility of CS and DES to prepare homogeneous dense blend membranes has been investigated. Different techniques, such as scanning electron microscopy, contact angle (CA), atomic force microscopy (AFM), Fourier transformed infrared spectroscopy (FTIR) and swelling...
-
A model of liquid film breakdown formed due to impingement of a two-phase jet on a horizontal surface
PublikacjaThe present work aims to provide an explanation to the phenomenon of breakdown of the thin liquid film created by impinging two-phase, liquid-gas jet. Existing in the literature models describe merely thebreakdown of single phase liquid films. The model presented here is based on examination of mass and energy equations under the applied criterion of the minimum of total energy. That allows to determinethe minimum thickness of...
-
The influence of a change in the meniscus cross-sectional shape on the medio-lateral translation of the knee joint and meniscal extrusion
PublikacjaObjective The purpose of this study was to evaluate the influence of a change in the meniscus cross sectional shape on its position and on the biomechanics of a knee joint. Methods One main finite element model of a left knee joint was created on the basis of MRI images. The model consisted of bones, articular cartilages, menisci and ligaments. Eight variants of this model with an increased or decreased meniscus height were then...
-
Influence of Two-Stage Anodization on Properties of the Oxide Coatings on the Ti–13Nb–13Zr Alloy
PublikacjaThe increasing demand for titanium and its alloys used for implants results in need of such innovative surface treatment that may jointly increase corrosion resistance and biocompatibility, and demonstrate antibacterial protection at no cytotoxicity. The purpose of this research was to characterize the effect of two-stage anodization, performed for 30 min in phosphoric acid, at the presence of hydrofluoric acid in the second stage....
-
Influence of Different Nanometals Implemented in PMMA Bone Cement on Biological and Mechanical Properties
PublikacjaCemented arthroplasty is a common process to fix prostheses when a patient becomes older and his/her bone quality deteriorates. The applied cements are biocompatible, can transfer loads, and dampen vibrations, but do not provide antibacterial protection. The present work is aimed at the development of cement with antibacterial effectivity achieved with the implementation of nanoparticles of different metals. The powders of Ag,...
-
Hyperbranched polyethylenimine functionalized silica/polysulfone nanocomposite membranes for water purification
PublikacjaHyperbranched polyethyleneimine functionalized silica (PEI-SiO2) nanoparticles with considerable hydrophilicity were synthesized and incorporated into a polysulfone (PSF)/dimethylacetamide (DMA)/polyvinylpyrrolidone (PVP) membrane casting solution in five different ratios to fabricate PEI-SiO2/PSF nanocomposite membranes using nonsolvent-induced phase separation. The hydrophilic PEI-SiO2 nanoparticles were characterized by TEM,...
-
The Chemical and Biological Properties of Nanohydroxyapatite Coatings with Antibacterial Nanometals, Obtained in the Electrophoretic Process on the Ti13Zr13Nb Alloy
PublikacjaThe risk of an early inflammation after implantation surgery of titanium implants has caused the development of different antimicrobial measures. The present research is aimed at characterizing the effects of nanosilver and nanocopper dispersed in the nanohydroxyapatite coatings, deposited on the Ti13Zr13Nb alloy, and on the chemical and biological properties of the coatings.The one-stage deposition process was performed by the...
-
Electrophoretic Deposition and Characteristics of Chitosan–Nanosilver Composite Coatings on a Nanotubular TiO2 Layer
PublikacjaThe surface treatment of titanium implants has been applied mainly to increase surface bioactivity and, more recently, to introduce antibacterial properties. To this end, composite coatings have been investigated, particularly those based on hydroxyapatite. The present research was aimed at the development of another coating type, chitosan–nanosilver, deposited on a Ti13Zr13Nb alloy. The research comprised characterization of the...
-
Assessment of the impact of bacteria Pseudomonas denitrificans, Pseudomonas fluorescens, Bacillus subtilis and yeast Yarrowia lipolytica on commercial poly(ether urethanes)
PublikacjaThe assessment of the impact of the bacteria Pseudomonas denitrificans, Pseudomonas fluorescens, Bacillus subtilis and yeast Yarrowia lipolytica on commercial poly(ether urethanes) Tecoflex® and Tecothane® is presented. The polyurethane samples were incubated with pure cultures of the microorganisms at 30 °C for five months. The changes in the chemical structure of the polymers were evaluated using loss of weight and contact angle...
-
Polyurethane glycolysate from industrial waste recycling to develop low dielectric constant, thermally stable materials suitable for the electronics
PublikacjaWe are utilizing a new method to improve the dielectric properties of a conventional polymer using a recycled polymer product. The polyurethane foams are recycled by glycolysis process and the derived material was applied to improve the dielectric properties of the brittle DGEBA epoxy resin. Two main parameters that determine the applicability of the material as a dielectric (the dielectric constant and dielectric loss), were studied...
-
Zeolitic imidazolate framework (ZIF-8) modified cellulose acetate NF membranes for potential water treatment application
PublikacjaIn this study, cellulose acetate (CA)-based nanofiltration membranes, modified with zeolitic imidazole framework-8 (ZIF-8) particles, were prepared with various ZIF-8 contents (0, 0.1, 0.25, 0.5, 1 and 2 wt%), to obtain membranes with improved flux and filtration performance by combining advantages of CA polymer and ZIF-8 metal-organic frameworks. Removal efficiency studies were carried out with bovine serum albumin and two different...
-
Superhydrophobic sponges based on green deep eutectic solvents for spill oil removal from water
PublikacjaThe paper described a new method for crude oil-water separation by means of superhydrophobic melamine sponges impregnated by deep eutectic solvents (MS-DES). Due to the numerous potential of two-component DES formation, simple and quick screening of 156 non-ionic deep eutectic solvents using COSMO-RS (Conductor-like Screening Model for Real Solvents) computational model was used. DES which were characterized by high solubility...
-
Sphere Drive and Control System for Haptic Interaction With Physical, Virtual, and Augmented Reality
PublikacjaA system for haptic interaction with physical, virtual, and augmented realities, founded on drive and measurement elements (DMEs), is considered. The system consists of eight DME rolls equipped with linear actuators, able to measure their angular velocity, drive the sphere, and adjust downforce (pressing the roll against the sphere). Two modeling issues are addressed. Special effort is put in to compensate for various technical...
-
In Vitro Biological Characterization of Silver-Doped Anodic Oxide Coating on Titanium
PublikacjaDespite the high biocompatibility and clinical effectiveness of Ti-based implants, surface functionalization (with complex osteointegrative/antibacterial strategies) is still required. To enhance the dental implant surface and to provide additional osteoinductive and antibacterial properties, plasma electrolytic oxidation of a pure Ti was performed using a nitrilotriacetic acid (NTA)-based Ag nanoparticles (AgNP)-loaded calcium–phosphate...
-
Properties of Nanohydroxyapatite Coatings Doped with Nanocopper, Obtained by Electrophoretic Deposition on Ti13Zr13Nb Alloy
PublikacjaNowadays, hydroxyapatite coatings are the most common surface modification of long-term implants. These coatings are characterized by high thickness and poor adhesion to the metallic substrate. The present research is aimed at characterizing the properties of nanohydroxyapatite (nanoHAp) with the addition of copper nanoparticle (nanoCu) coatings deposited on the Ti13Zr13Nb alloy by an electrophoresis process. The deposition of...