Filtry
wszystkich: 902
-
Katalog
Wyniki wyszukiwania dla: WASTE PLASTIC STRAWS
-
Zagospodarowanie ciepła odpadowego z biogazowych agregatów kogeneracyjnych w oczyszczalni ścieków
PublikacjaW pracy opisano koncepcję współpracy biogazowych modułów kogeneracyjnych z niskotemperaturowym obiegiem parowym. Proponowana modernizacja pozwoliłaby na wykorzystanie entalpii fizycznej spalin, tym samym zwiększając sprawność urządzeń wytwarzających ciepło i energię elektryczną. Tego typu rozwiązanie umożliwiłoby częściowe pokrycie zapotrzebowania własnego na energię elektryczną, generując oszczędności w przedsiębiorstwie. W artykule...
-
Numerical analyses of novel prefabricated structural wall panels in residential buildings based on laboratory tests in scale 1:1
PublikacjaThe paper presents experimental and numerical investigations on novel prefabricated composite building wall panels for residential building constructions. The wall panels were composed of reinforced concrete ribbed elements with the core from the EPS foam as the thermal insulation. The wall panels in the full-scale 1:1 were subjected to vertical loads. In the first step, the experiments were analysed with simple usual static methods....
-
Experimental study on the behaviour of steel columns under seismic-induced axial impact load
PublikacjaIt has been observed during major earthquakes that the so called soft-storey failure of an upper floor of a structure results in large impact load acting on structural members of the lower storeys. It may further lead to progressive collapse of the whole structure substantially intensifying human and material losses. Therefore, the aim of this paper is to investigate experimentally the behaviour of columns under bending (observed...
-
Super tough interpenetrating polymeric network of styrene butadiene rubber‐poly (methyl methacrylate) incorporated with general purpose carbon black ( N660 )
PublikacjaA classic set of polymeric interpenetrating polymeric network (IPN) microcomposites has been fabricated using an elastomer—styrene butadiene rubber [SBR], a thermoplastic poly(methyl methacrylate)-PMMA and with carbon black (CB)-N660 as a filler and reinforcing agent. This synthesized IPN composite can be promisingly employed as a toughened plastic and vibrational damper in a wide service range with excellent thermal stability,...
-
Hydrogen production from biomass using dark fermentation
PublikacjaHydrogen applicability in the power, chemical and petrochemical industries is constantly growing. Efficientmethods of hydrogen generation from renewable sources, including waste products, are currently being de-veloped, even though hydrogen is mainly produced through steam reforming or thermal cracking of natural gasor petroleum fractions. In paper alternative methods of hydrogen production with a particular emphasis on darkfermentation...
-
Tackling microplastics pollution in global environment through integration of applied technology, policy instruments, and legislation
PublikacjaMicroplastic pollution is a serious environmental problem that affects both aquatic and terrestrial ecosystems. Small particles with size of less than 5 mm, known as microplastics (MPs), persist in the environment and pose serious threats to various species from micro-organisms to humans. However, terrestrial environment has received less attention than the aquatic environment, despite being a major source of MPs that eventually...
-
Inkjet Printing of Lanthanide–Organic Frameworks for Anti-Counterfeiting Applications
PublikacjaPhotoluminescent lanthanide−organic frameworks (Ln-MOFs) were printed onto plastic and paper foils with a conventional inkjet printer. Ln-MOF inks were used to reproduce color images that can only be observed under UV light irradiation. This approach opens a new window for exploring Ln-MOF materials in technological applications, such as optical devices (e.g., lab-on-a-chip), as proof of authenticity for official documents.
-
Reactive Processing and Functionalization of Ground Tire Rubber
PublikacjaThe dynamic development of the automotive industry resulted in a sig- nificant increase in rubber wastes, especially end-of-life tires, which are a serious threat to the natural environment and human health. This situation has enforced the industry and academic research groups to search new and cost-effective methods for recycling waste tires. In this field of research, reactive processing and functionaliza- tion seem to be a...
-
Renewable Resources for Polyurethanes and Polyurethane Composites: A Review
PublikacjaEach year, more than two million tons of polyurethane is produced in the EU by reacting isocyanates with polyols made from fossil fuel. In addition, there are appreciable quantities of petroleum based functional additives applied in the industry nowadays for both polyols and polyurethane materials. It is therefore of key importance to develop sustainable economically viable polyols with enhanced functionalities, and thereby reducing...
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_v_2
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_v_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_h_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_v_5
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_h_5
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_h_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_h_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_v_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_h_5
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_v_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 009_v_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_v_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_v_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_h_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_h_5
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_h_4
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_v_2
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 039_h_3
Dane BadawczeData gathered in sliding ring-on-block (flat contact) tribological experiment. Materials: alloy steel (heat treated) vs. ABS plastic.
-
End-of-life management of single-use baby diapers: Analysis of technical, health and environment aspects
PublikacjaSingle-use baby diapers belongs to an important group of products used in the parenting journey because of their high performance and convenience. Single-use baby diapers are normally thrown away after one-time use, resulting in a waste management problem. The goal of this paper was to better understand main environmental concerns of different types of diapers and address how to reduce them, with a special consideration of waste...
-
Nanotechnologies in Development of Structural Materials and Biomaterials
PublikacjaThe nanometric materials and technologies resulted in nanostructures are reviewed. The examples of nanomaterials are shown. The typical nanotechnologies, including plastic deformation, mechanical attrition, controlled detonation, hot plasma jet synthesis, laser vaporisation, CVD and PVD, mechanical milling, annealing, ultrasonic irradiation, nanolithography, electrocrystallisation, electrospinning, sol-gel method, cryogenic laser-enhanced...
-
Development of conductive porous media as packing materials for biotrickling filter – microbial fuel cell system (BTF-MFC system)
Dane BadawczeDataset presents values of electrical resistance measured for three developed conductive packimg materials for the application in a BTF-MFC system.
-
RENEMO Redukcja emisji N2O w oczyszczalniach ścieków – pomiary, modelowanie i optymalizacja procesu
ProjektyProjekt realizowany w Wydział Inżynierii Lądowej i Środowiska zgodnie z porozumieniem WPN/7/2013 z dnia 2013-07-15
-
Insights into baby disposable diapers sustainable application
PublikacjaThe sustainable use of baby disposable diapers is one of the issues currently being discussed to reduce the undesirable impact on the environment and improve the public's understanding of the proper use of diapers. This issue is a step toward promoting a cleaner, greener, and waste-less environment. In this article, the authors discuss options for a viable future for both people and the planet. We believe that it inspire others...
-
RB21T RECO Baltic 21 Tech
ProjektyProjekt realizowany w Wydział Chemiczny zgodnie z porozumieniem #64 z dnia 2011-01-13
-
Thermo-Chemical Decomposition Study of Polyurethane Elastomer Through Glycerolysis Route with Using Crude and Refined Glycerine as a Transesterification Agent
PublikacjaDue to the increasing amount of polyurethane waste, chemical recycling of these materials is a topic of growing interest for many researchers. The primary pur- pose of polyurethane feedstock recycling is to recover the starting polyol. In this study glycerolysis using glycerine from two sources and two purity grades is proposed as a method of chemical recycling. The main effort of this paper focuses on the employment of commercial...
-
OIL-ASSISTED THERMO-MECHANICAL RECLAMATION OF GROUND TIRE RUBBER
PublikacjaNowadays, it is crucial to seek for the methods of by-products and waste utilization, considering both environmental and economic factors. The example of waste material generated in the massive amounts, which requires the attention is ground tire rubber generated during recycling of post-consumer car tires. It can be applied as a filler into different polymer matrices, but to enhance its effectivity proper modifications should...
-
Zbigniew Łubniewski dr hab. inż.
Osoby -
SELECTED COMBINED POWER SYSTEMS CONSISTED OF SELFIGNITION ENGINE AND STEAM TURBINE
PublikacjaThis paper presents optimization of selected combined diesel engine-steam turbine systems. Two systems: the system combined with waste heat one-pressure boiler only and its version containing additionally low-pressure boiler proper feeding degasifier and the system of two-pressure cycle, were taken into considerations. Their surplus values of power output and efficiency associated with utilization of waste heat contained in piston...
-
WERYFIKACJA KONCEPCJI PRZEGUBÓW PLASTYCZNYCH PROJEKTOWANYCH NA ODZIAŁYWANIA SEJSMICZNE WIADUKTU V6 OBWODNICY ISTAMBUŁU
PublikacjaW pracy zawarto wyniki analiz betonowego wiaduktu V6 budowanego w ciągu obwodnicy Istambułu w Turcji realizowanego w ramach projektu Northern Marmara Highway. Przeprawę stanowią dwie niezależne nitki o skrzynkowym przekroju poprzecznym i szerokości 22,00 m. Schemat statyczny obiektu to belka dziewięcioprzęsłowa o długości całkowitej 446,86 m oparta na podporach słupowych o zmiennej sztywności (rys.1) i wysokościach zmieniających...
-
"Raport z wstępnych badań własności stali trudnościeralnej 460HB",. ang "Report on preliminary tests of the properties of wear-resistant steel 460HB"
PublikacjaMikrostrukturę badanej stali trudnościeralnej 460HB stanowi drobnoziarnisty martenzyt odpuszczony, który jest właściwy dla stali konstrukcyjnych niskowęglowych, niskostopowych ulepszonych cieplnie. W przypadku blach grubych, do których zalicza się badana stal, struktura może ulec zaburzeniu, jeżeli w hutniczym procesie wytwórczym wystąpiła niejednorodność odkształcenia plastycznego i w konsekwencji tworzenie się pasm segregacyjnych,...
-
Energy Systems Stations, W, ET, sem.7, zimowy 22/23 (PG_00042106)
Kursy OnlineInternal combustion engines - principle of operation and classification. Heat balance of the engine. Uniform and combined propulsion systems.The main comonents of the propulsion system. Power plant efficiency and waste heat utilization. Cooling water system, lubricating oil system, fuel oil systeml, gaseos fuel system (LNG), compressed air system, exhaust gas system. Fittings and accessories of pipeline systems in the power plant....
-
Management of low-temperature heat source by ORC aided by additional heat source
PublikacjaThe presented work is aimed at utilisation of waste heat in the manner to produce electricity in ORC installation. Therefore the precondition of the study was to use the waste heat available in the form of a stream of hot water at 90°C. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. That was the incentive to search for the ways of increasing the temperature of the...
-
Implementing fermentation technology for comprehensive valorisation of seafood processing by-products: A critical review on recovering valuable nutrients and enhancing utilisation
PublikacjaFermentation technology is a biorefining tool that has been used in various industrial processes to recover valuable nutrients from different side streams. One promising application of this technique is in the reclamation of nutritional components from seafood side streams. Seafood processing generates significant amounts of waste, including heads, shells, and other side streams. These side streams contain high quantities of valued...
-
ACTIVATED BIOCHAR AS AN ADSORBENT OF ORGANIC POLLUTANTS FOR WATER AND WASTEWATER TREATMENT
PublikacjaThe use of biomass, especially waste biomass, as an alternative energy source is a very important issue today. Pyrolysis is a process of thermal degradation of raw material and one of its products is biochar. This product is mainly distinguished by its high carbon content, and by improving its quality through activation, it can be more widely used. Activated biocarbon has a strongly developed surface and porous structure, and as...
-
S-scheme heterojunction Bi2O3-ZnO/Bentonite clay composite with enhanced photocatalytic performance
PublikacjaThe industrial waste water is always a bottleneck problem in the modern civilization of the present era. In a quest to develop effective methods for the elimination of lethal pollutants from the waste water and water remediation, this work is focused on the development of a rapid and proficient approach for preparing supported binary metal oxide catalyst for photocatalytic advance oxidation process used in waste water treatment...
-
Launching of steel bridge girder. Application of nonlinear shell models
PublikacjaThe paper describes the final technology of launching the steel bridge superstructure. The original technology failed in the first construction stage. Local damage of steel webs caused by plastic buckling stopped the procedure. In the effect of damage a new consulting team was employed to solve the problem and redesign a technology of constructing. The key element of the new solution was developed with great help of non-linear...
-
Detection of person presence and its activity in the bathtub
PublikacjaA practical application of a bioimpedance technique for a detection of a bathing person is presented in the paper. It addresses the possibility of supervising people in the bathtub without voiding of their intimacy. The measurement system installed in a fiber-glass or a plastic bathtub is able to detect a presence of the bathing person, to estimate its activity and thus to detect potentially dangerous events. In the paper a principle...
-
3D-Breast System for Determining the Volume of Tissue Needed for Breast Reconstruction
Publikacja3D imaging systems can be used to effectively determine breast volumes for surgical applications. This article presents methods for surface reconstruction and volume determination based on the point cloud created by 3D imaging. Such a system would be used to accurately estimate breast volume in patients classified for breast reconstruction surgery at plastic surgery centers. To develop such a system, various methods of determining...
-
Management of low-temperature heat source by ORC aided by additional heat source
PublikacjaIn the paper presented is a concept to utilize waste heat from the power plant with the aid of the low-temperature ORC cycle. The ORC system is heated from two heat sources, the first one being the flow rate of waste heat obtained from the exhaust gases. Subsequently, the working fluid in the cycle is additionally heated by the condensing steam from the low pressure turbine extraction points increasing in such way the level of...
-
Immunophenotyping and transcriptional profiling of in vitro cultured human adipose tissue derived stem cells
PublikacjaAdipose-derived stem cells (ASCs) have become an important research model in regenerative medicine. However, there are controversies regarding the impact of prolonged cell culture on the ASCs phenotype and their differentiation potential. Hence, we studied 10 clinical ASCs replicates from plastic and oncological surgery patients, in six-passage FBS supplemented cultures. We quantified basic mesenchymal cell surface marker transcripts...
-
The investigation of polyester composites filled by modified bentonite
PublikacjaPraca dotyczy zagospodarowania odpadów poliestrowo-szklanych przez wytworzenie kompozytów z ich użyciem oraz żywicy poliestrowej, mączki dolomitowej i nanonapełniacza. Wykazano, ze dodatek 2% nanonapełniacza do do kompozytów poliestrowych zawierających 15% masowych odpadów pozwala na uzyskanie materiału wykazującego korzystne właściwości wytrzymałościowe. Proponowany sposób modyfikacji kompozytów poliestrowych jest nowym rozwiązaniem...