Wyniki wyszukiwania dla: MECHANICAL ENGINEERING
-
Assessment of unusual failure in crankshaft of heavy-duty truck engine
PublikacjaThe unusual premature failure of a heavy-duty truck engine crankshaft has been the subject of a rigorous study, and this manuscript describes it in detail. The failure was happened to begin with the growth of the crack from the surface defects, in the form of the clusters of non-metallic inclusions, in the lubrication hole zone of the first main journal, which was the stress concentration zone. A series of experiments including...
-
The influence of phosphorus fractions in bottom sediments on phosphate removal in semi-natural systems as the 3rd stage of biological wastewater treatment
PublikacjaThe research was carried out in two semi-natural systems (the polishing ponds in Swarzewo and the free water surface constructed wetland in Zarnowiec) in Poland. They were built as the 3rd stage of a conventional mechanical–biological wastewater treatment plant. These systems were built to improve the quality of the effluent of treated wastewater. In the polishing ponds and FWS wetland system, suspended solids, organic matter as...
-
Load capacity of steel-aluminium brackets under static and cyclic laboratory tests
PublikacjaThe aim of the research is the laboratory investigation of steel-aluminium brackets employed to fasten lightweight curtain walls to building facilities. Static pressure, suction forces, and cyclic loads parallel to end plates (horizontal – to simulate wind influence) were applied in the study. The steel-aluminium brackets were tested on a reinforced concrete substrate made of C30/37 concrete class to simulate the real working conditions....
-
Influence of soil anisotropic stiffness on the deformation induced by an open pit excavation.
PublikacjaIn this paper, the problem of deformation induced by an open pit excavation in anisotropic stiff soils is analysed by FE modelling. The presented research is focused on the influence of material model with anisotropic stiffness on the accuracy of deformation predictions as compared with the field measurements. A new hyperelastic-plastic model is applied to simulate anisotropic mechanical behaviour of stiff soils. It is capable...
-
Damage of a post-tensioned concrete bridge – Unwanted cracks of the girders
PublikacjaThe cracking of a post-tensioned T-beam superstructure, which was built using the incremental launching method, is analyzed in the paper. The problem is studied in detail, as specific damage was observed in the form of longitudinal cracks, especially in the mid-height zone of the girder at the interface of two assembly sections. The paper is a case study. A detailed inspection is done and non-destructive testing results of the...
-
Advances in Modelling and Analysis of Strength of Corroded Ship Structures
PublikacjaThe present study reviews the recent advances in modelling and analyses the strength of corroded ship structures. Firstly, the time-variant methodologies that consider only the mean structural element thickness loss due to corrosion degradation are identified. Corrosion degradation is regarded as the phenomenon that causes uneven thinning of specimens. This has been captured by various researchers as the loss of mechanical properties...
-
Fabrication and Characterization of Green Polyurethane Foams with Enhanced Vibration Damping Capability
PublikacjaOver the past decades, there has been an intensive development of the technologies and innovations aimed at increasing the quality of life. This development largely concerns the comfort of use of everyday products that, among others, are products of the automotive, construction, or furniture industries. Considering the increase in the comfort of using products such as cars, houses, and flats, one of the comfort features of their...
-
Abual Hassan Mr.
OsobyI have completed my B.Sc in Industrial and Manufacturing Engineering in 2017 from the University of Engineering and Technology in Lahore, Pakistan. In 2017 Chinese Govt Offered me a Fully funded scholarship and completed my MEng in Mechanical Engineering from Northwestern Polytechnical University Xi'an, China. There I graduated with the honor of Excellent Post-Graduate Student of the Year 2020. My research interests include Additive...
-
Core loss resistance impact on sensorless speed control of an induction motor using hybrid adaptive sliding mode observer
PublikacjaInduction motors (IMs) experience power losses when a portion of the input power is converted to heat instead of driving the load. The combined effect of copper losses, core losses, and mechanical losses results in IM power losses. Unfortunately, the core losses in the motor, which have a considerable impact on its energy efficiency, are not taken into account by the generally employed dynamic model in the majority of the studies. Due...
-
[AEiE] Selected topics of electrical engineering - models of electrical machines
Kursy Online{mlang pl} Dyscyplina: automatyka, elektronika i elektrotechnika Zajęcia fakultatywne dla doktorantów II roku Prowadzący: dr hab. inż. Andrzej Wilk, prof. PG, prof. dr hab. inż. Zbigniew Krzemiński Liczba godzin: 15 Forma zajęć: wykład {mlang} {mlang en} Discipline: control, electronic and electrical engineering Facultative course for 2nd-year PhD students Academic teachers: dr hab. inż. Andrzej Wilk, prof. PG, prof....
-
A novel one-variable first-order shear deformation theory for biaxial buckling of a size-dependent plate based on Eringen’s nonlocal differential law
PublikacjaPurpose – This paper aims to present a new one-variable first-order shear deformation theory (OVFSDT) using nonlocal elasticity concepts for buckling of graphene sheets. Design/methodology/approach – The FSDT had errors in its assumptions owing to the assumption of constant shear stress distribution along the thickness of the plate, even though by using the shear correction factor (SCF), it has been slightly corrected, the errors...
-
Monte Carlo simulations of the fracture resistance degradation of asphalt concrete subjected to environmental factors
PublikacjaThe paper presents the results of laboratory tests of SCB (semi-circular beam) samples of asphalt concrete, subjected to the destructive effect of water and frost as well as the aging processes. The determined values of material parameters show significant dispersions, which makes the design of mixtures difficult. Statistical analysis of the test results supplemented by computer simulations made with the use of the proprietary...
-
Tadeusz Widerski dr inż.
OsobyW 1998 roku zdał maturę oraz ukończył Technikum Mechaniczne o profilu budowa maszyn w Dobrym Mieście. W latach 1998 -2003 odbył studia na Wydziale Geodezji i Gospodarki Przestrzennej Uniwersytetu Warmiństko Mazurskiego gdzie zdobył tytuł magistra inżyniera Geodezji i Kartografii. Od 2005 do 2009 roku był słuchaczem Studium Doktorskiego o specjalności geotechnika i inżynieria środowiska na Wydziale Inżynierii Lądowej i Środowiska...
-
Karol Rudziński inż.
OsobyKarol Rudziński (urodzony 18 sierpnia 1979 w Inowrocławiu). Po ukończeniu Technikum Budowy Okrętów w Gdańsku, kontynuował naukę na Wydziale Mechanicznym Politechniki Gdańskiej. Ukończył w 2007 r. studia I stopnia w specjalności: Mechanika i Budowa Maszyn, Technologia maszyn. Od 2002 r. rozpoczął pracę na wydziale Budownictwa Wodnego i Inżynierii Środowiska na Politechnice Gdańskiej (obecnie wydział Inżynierii Lądowej i Środowiska)...
-
Kacper Szturgulewski mgr inż.
OsobySpecjalista naukowo-techniczny w Politechnice Gdańskiej, wiodącej technicznej uczelni badawczej w Polsce. W chwili obecnej zajmuje się wysokoefektywnymi systemami energetycznymi z wykorzystaniem odnawialnych źródeł energii oraz technologii magazynowania energii. Uczestniczę w międzynarodowym projekcie Horizon Europe - 2LIPP (2nd Life for Power Plants), będącym częścią inicjatywy BRIDGE. Dodatkowo, aktywnie angażuje się w inicjatywy...
-
Predicting the seismic collapse capacity of adjacent SMRFs retrofitted with fluid viscous dampers in pounding condition
PublikacjaSevere damages of adjacent structures due to structural pounding during earthquakes have emphasized the need to use some seismic retrofit strategy to enhance the structural performance. The purpose of this paper is to study the influence of using linear and nonlinear Fluid Viscous Dampers (FVDs) on the seismic collapse capacities of adjacent structures prone to pounding and proposing modification factors to modify the median...
-
Lamb wave based structural damage detection using cointegration and fractal signal processing
Publikacja -
Deep learning based segmentation using full wavefield processing for delamination identification: A comparative study
Publikacja -
Deep learning super-resolution for the reconstruction of full wavefield of Lamb waves
Publikacja -
Towards homoscedastic nonlinear cointegration for structural health monitoring
Publikacja -
Damage identification by wavelet analysis
PublikacjaW pracy omówiono metodę identyfikacji rodzaju nieciagłości w 1 wymiarowych elementach konstrukcji wykorzystującą pomiar propagacji fali sprężystej i jej analizę metodą transformacji falkowej.
-
Investigation on the edge forces in ball end milling of inclined surfaces
Publikacja -
Mechanical and technological aspects of micro ball end milling with various tool inclinations
Publikacja -
Effects of extreme pressure and anti-wear additives on surface topography and tool wear during MQCL turning of AISI 1045 steel
Publikacja -
Full wavefield processing by using FCN for delamination detection
Publikacja -
Damage identification by wavelet analysis
Publikacja -
Research and applications of active bearings: A state-of-the-art review
Publikacja -
Saint-Venant torsion based on strain gradient theory
Publikacja -
Research and applications of active bearings: A state-of-the-art review
PublikacjaControllable/active bearings are mainly associated with active magnetic bearings (AMBs), whereas active bearing control is also found in many types of bearings, e.g. fluid, gas and hybrid bearings. The article presents a review of the literature describing the structure and results of studies of active bearings. Active control brings a number of benefits resulting in the fact that their use as a support for rotors becomes increasingly...
-
Monitoring the curing process of epoxy adhesive using ultrasound and Lamb wave dispersion curves
PublikacjaMonitoring the stiffness of adhesives is a crucial issue when considering the durability andstrength of adhesive joints. While there are many studies conducted on specimens madeonly from adhesive, the problem of curing of an adhesive film in real joints is moderatelyconsidered. This paper presents the monitoring of stiffening of epoxy adhesive using ultra-sound. Ultrasonic pulse velocity method was firstly applied for monitoring...
-
An adaptive-noise Augmented Kalman Filter approach for input-state estimation in structural dynamics
PublikacjaThe establishment of a Digital Twin of an operating engineered system can increase the potency of Structural Health Monitoring (SHM) tools, which are then bestowed with enhanced predictive capabilities. This is particularly relevant for wind energy infrastructures, where the definition of remaining useful life is a main driver for assessing the efficacy of these systems. In order to ensure a proper representation of the physical...
-
Detection and size estimation of crack in plate based on guided wave propagation
PublikacjaThe paper presents results of the comprehensive theoretical and experimental investigation of crack detection in metallic plate using guided wave propagation. The main aim of the paper is to develop the novel method which would allow for linear crack size estimation with the use of minimal number of the transducers. In general, there exists the relation between length of the propagation path and the wave amplitude value. However,...
-
A dynamic vehicle-bridge model based on the modal identification results of an existing EN57 train and bridge spans with non-ballasted tracks
PublikacjaThis paper addresses the methodology of the bridge-vehicle dynamic model definition based on the free response measurements of an existing train and existing bridge spans. In the case of the railway vehicle, the methodology uses the impulse excitations of a single car by means of the wedge method. In the case of the bridge spans, free responses are collected after the passages of trains. The global modal parameters (frequencies...
-
Optimal control of 2-wheeled mobile robot at energy performance index
PublikacjaThe paper presents the application of the optimal control method at the energy perfor- mance index towards motion control of the 2-wheeled mobile robot. With the use of the proposed method of control the 2-wheeled mobile robot can realise effectively the desired trajectory. The problem of motion control of mobile robots is usually neglected and thus performance of the realisation of the high level control tasks is limited.
-
Predicting the seismic collapse capacity of adjacent SMRFs retrofitted with fluid viscous dampers in pounding condition
PublikacjaSevere damages of adjacent structures due to structural pounding during earthquakes have emphasized the need to use some seismic retrofit strategy to enhance the structural performance. The purpose of this paper is to study the influence of using linear and nonlinear Fluid Viscous Dampers (FVDs) on the seismic collapse capacities of adjacent structures prone to pounding and proposing modification factors to modify the median...
-
A three-dimensional periodic beam for vibroacoustic isolation purposes
PublikacjaThis paper presents results of investigations on a three-dimensional (3-D) isotropic periodic beam. The beam can represent a vibroacoustic isolator of optimised dynamic characteristics in the case of its longitudinal, flexural and torsional behaviour. The optimisation process concerned both the widths as well as the positions of particular frequency band gaps that are present in the frequency spectrum of the beam. Since the dynamic...
-
Running performance of an aerodynamic journal bearing with squeeze film effect
PublikacjaResults of theoretical and experimental studies concerning the performance of an aerodynamic journal bearing of which running is assisted by squeeze film ultrasonic levitation (SFUL) are presented in this paper. The SFUL mechanism not only can separate journal from the bearing at the start and stop phases of operation but also can significantly contribute to the dynamic stability of the bearing when it runs at speed. Computer calculations...
-
Chatter vibration surveillance by the optimal-linear spindle speed control
PublikacjaArtykuł dotyczy drgań samowzbudnych typu chatter podczas obróbki szybkościwowej frezami kulistymi. Opisano w nim niestacjonarny model procesu skrawania oraz przeprowadzono analizy dynamiki układu z opóźniającym sprzężeniem zwrotnym. W celu zredukowania drgań zaproponowano zmiany prędkości obrotowej wrzeciona. Przedstawiono także procedurę nadzorowaia drgań z wykorzystaniem opisanej metody. Dla wybranych przypadków, w artykule przedstawiono...
-
Improvement of damage detection methods based on experimental modal parameters
PublikacjaW pracy przedstwiono sposoby porawy czułości metod detekcji uszkodzeń wykorzystujacych eksperyentalne parametry modalne konstrukcji. Wykazano, że zastosowanie zawansowanych technik obróbki sygnałów pomiarowych pozwala zdecydowanie poprwaić skutecznośc znanych z literatury metod.
-
Saint-Venant torsion based on strain gradient theory
PublikacjaIn this study, the Saint-Venant torsion problem based on strain gradient theory is developed. A total form of Mindlin's strain gradient theory is used to acquire a general Saint-Venant torsion problem of micro-bars formulation. A new Finite Element formulation based on strain gradient elasticity theory is presented to solve the Saint-Venant torsion problem of micro-bars. Moreover, the problem is solved for both micro and macro...
-
Corrosion damage identification based on the symmetry of propagating wavefield measured by a circular array of piezoelectric transducers: Theoretical, experimental and numerical studies
PublikacjaThe article investigates the results obtained from numerical simulations and experimental tests concerning the propagation of guided waves in corroded steel plates. Developing innovative methodologies for assessing corrosion-induced degradation is crucial for accurately diagnosing offshore and ship structures exposed to harsh environmental conditions. The main aim of the research is to analyze how surface irregularities affect...
-
Cyclic behaviour modelling of additively manufactured Ti-6Al-4V lattice structures
PublikacjaThe present work is concerned with the numerical modelling of the cyclic behaviour of Ti-6Al-4V lattice structures. In the study, diamond structures of titanium alloy produced by the additive laser powder bed fusion (LPBF) method with different degrees of relative density were used. Realistic geometric models of the studied mesostructures were generated using computed microtomography, taking into account the imperfections of the...
-
Smooth least absolute deviation estimators for outlier-proof identification
PublikacjaThe paper proposes to identify the parameters of linear dynamic models based on the original implementation of least absolute deviation estimators. It is known that the object estimation procedures synthesized in the sense of the least sum of absolute prediction errors are particularly resistant to occasional outliers and gaps in the analyzed system data series, while the classical least squares procedure unfortunately becomes...
-
Dynamic mass measurement in checkweighers using a discrete time-variant low-pass filter
PublikacjaConveyor belt type checkweighers are complex mechanical systems consisting of a weighing sensor (strain gauge load cell, electrodynamically compensated load cell), packages (of different shapes, made of different materials) and a transport system (motors, gears, rollers). Disturbances generated by the vibrating parts of such a system are reflected in the signal power spectra in a form of strong spectral peaks, located usually in...
-
A modified method of vibration surveillance by using the optimal control at energy performance index
PublikacjaA method of vibration surveillance by using the optimal control at energy performance index has been creatively modified. The suggested original modification depends on consideration of direct relationship between the measured acceleration signal and the optimal control command. The paper presents the results of experiments and Hardware- in-the-loop simulations of a new active vibration reduction algorithm based on the energy...
-
The instantaneous frequency rate spectogram
PublikacjaAn accelerogram of the instantaneous phase of signal components referred to as an instantaneous frequency rate spectrogram (IFRS) is presented as a joint time-frequency distribution. The distribution is directly obtained by processing the short-time Fourier transform (STFT) locally. A novel approach to amplitude demodulation based upon the reassignment method is introduced as a useful by-product. Additionally, an estimator of energy...
-
Systemidentificationbasedapproachtodynamicweighing revisited
PublikacjaDynamicweighing,i.e.,weighingofobjectsinmotion,withoutstoppingthemonthe weighing platform,allowsonetoincreasetherateofoperationofautomaticweighing systems, usedinindustrialproductionprocesses,withoutcompromisingtheiraccuracy. Sincetheclassicalidentification-basedapproachtodynamicweighing,basedonthe second-ordermass–spring–dampermodeloftheweighingsystem,doesnotyieldsa- tisfactoryresultswhenappliedtoconveyorbelttypecheckweighers,severalextensionsof thistechniqueareexamined.Experimentsconfirmthatwhenappropriatelymodifiedthe identification-basedapproachbecomesareliabletoolfordynamicmassmeasurementin checkweighers.
-
Damage localisation in a stiffened plate structure using a propagating wave
PublikacjaThe paper presents an application of changes in propagating waves for damage detection in a stiffened aluminium plate. The experimental investigation was conducted on an aluminium plate with riveted two L-shape stiffeners. The wave has been excited with a piezoelectric transducer and measured with the Laser Scanning Doppler Vibrometer. Recorded signals were analysed using the special signal processing techniques developed for damage...
-
Fluid–Structure Interaction methods for the progressive anatomical and artificial aortic valve stenosis
PublikacjaCardiovascular system diseases, as aortic valve stenosis, are the main cause of mortality and morbidity among patients. There is still a room for enhancement of the diagnostic and therapeutic procedures, which will lead to improvement of the treatment. One of the remedies are the computer tools to support the medical diagnoses and prostheses design. The development of a procedure for modeling the aortic valves: anatomical tricuspid...
-
Prediction of maximum tensile stress in plain-weave composite laminates with interacting holes via stacked machine learning algorithms: A comparative study
PublikacjaPlain weave composite is a long-lasting type of fabric composite that is stable enough when being handled. Open-hole composites have been widely used in industry, though they have weak structural performance and complex design processes. An extensive number of material/geometry parameters have been utilized for designing these composites, thereby an efficient computational tool is essential for that purpose. Different Machine Learning...