Wyszukiwarka
Filtry
wszystkich: 1059
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: bitumen-polymer blend
-
Validation Process for Computational Model of Full-Scale Segment for Design of Composite Footbridge
PublikacjaExperimental tests and numerical simulations of a full-scale segment of a foot and cycle bridge made of polymer composites are presented in the paper. The analysed structure is made of sandwich panels, which consist of glass fibre reinforced polymer (GFRP) multi-layered laminate faces and a PET foam (obtained from recycling) core. The dimensions of the segment cross-section are the same as for the target footbridge; however, span...
-
Sensing the onset of epoxy coating degradation with combined Raman spectroscopy/atomic force microscopy/electrochemical impedance spectroscopy
PublikacjaThe paper presents the results of investigation on epoxy resin durability upon 12-week exposure to UV radiation. The aim was early determination of the onset of epoxy degradation and for this purpose an epoxy film on steel substrate systems were periodically inspected using Raman spectroscopy, atomic force microscopy and electrochemical impedance spectroscopy. The behaviour of examined polymer could be divided into three periods: immunity,...
-
High-density Polyethylene - Expanded Perlite Composites: Structural Oriented Analysis of Mechanical and Thermomechanical Properties
PublikacjaAs part of this work, research was carried out on the effect of the addition of expanded perlite (PR) on the mechanical and thermomechanical properties of high-density polyethylene (PE) composites. Composites containing from 1 to 10 wt% of the inorganic filler were produced. Polyethylene-based composites manufactured by twin-screw extrusion and formed in the compression molding process were subjected to mechanical, thermomechanical,...
-
Waste tire rubber as low-cost and environmentally-friendly modifier in thermoset polymers – a review
PublikacjaNowadays, waste tire rubber (WTR) management is a growing and serious problem. Therefore, research works focused on the development of cost-effective and environmentally-friendly methods of WTR recycling are fully justified. Incorporation of WTR into polymer matrices and composite materials attracts much attention, because this approach allows sustainable development of industrially applicable waste tires recycling technologies....
-
Experimental Studies of Concrete-Filled Composite Tubes under Axial Short- and Long-Term Loads
PublikacjaThe paper presents experimental studies on axially compressed columns made of concrete-filled glass fiber reinforced polymer (GFRP) tubes. The infill concrete was C30/37 according to Eurocode 2. The investigated composite pipes were characterized by different angles of fiber winding in relation to the longitudinal axis of the element: 20, 55 and 85 degrees. Columns of two lengths, 0.4 m and 2.0 m, were studied. The internal diameter...
-
Low Noise Poroelastic Road Pavements Based On Bituminous Binder
PublikacjaTire/road noise is the dominant source of traffic noise. It depends both on the tire design and on the characteristics of road pavements as well as on the vehicles’ operating conditions. Due to the fact that conventional (pneumatic) car tires have almost reached the limits of their ability to further reduce their noisiness, it is widely believed that the additional reduction of tire noise will be possible mainly through modifications...
-
Strain-dependent behaviour of cold recycled material mixtures in cyclic compression tests
PublikacjaThe purpose of the study is to evaluate strain-dependent behaviour of Cold Recycled Material (CRM) mixtures using three frameworks typically applied for Hot Mix Asphalt (HMA): linear viscoelastic (LVE) limits; non-linearity directions; changes in rheological model parameters. To this aim, the complex modulus of three CRM mixtures with different bitumen-to-cement ratio (0.2, 0.6 and 1.8) was measured in cyclic compression mode,...
-
Method for the simultaneous determination of monoaromatic and polycyclic aromatic hydrocarbons in industrial effluents using dispersive liquid-liquid microextraction with GC-MS
PublikacjaWe present a new method for simultaneous determination of 22 monoaromatic and polycyclic aromatic hydrocarbons in postoxidative effluents from the production of petroleum bitumen using dispersive liquid-liquid microextraction coupled to gas chromatography and mass spectrometry. The eight extraction parameters including the type and volume of extraction and disperser solvent, pH, salting out effect, extraction and centrifugation...
-
ANALYSIS OF CLIMATIC ZONES IN POLAND WITH REGARD TO ASPHALT PERFORMANCE GRADING
PublikacjaTowards the end of the last century a new system of bitumen grading was developed and implemented as part of the American Strategic Highway Research Program (SHRP). Its aim was to better adjust the testing methods and requirements for road bitumens to the actual conditions in which those bitumens serve in road pavements. Currently in Poland, similarly as in the other EU countries, road bitumens are tested and classified with regard...
-
The impact of thermomechanical and chemical treatment of waste Brewers’ spent grain and soil biodegradation of sustainable Mater-Bi-Based biocomposites
PublikacjaDue to the massive plastic pollution, development of sustainable and biodegradable polymer materials is crucial to reduce environmental burdens and support climate neutrality. Application of lignocellulosic wastes as fillers for polymer composites was broadly reported, but analysis of biodegradation behavior of resulting biocomposites was rarely examined. Herein, sustainable Mater-Bi-based biocomposites filled with thermomechanically-...
-
Are you the change? Exploring citizen engagement for Smart Sustainable Cities
Kursy OnlineThe purpose of this course is to explore citizen engagement in the context of smart, sustainable cities, with the goal of providing students with an understanding of the principles and practices involved in urban landscaping. Throughout the course, students will explore key concepts and practical applications across various domains, from understanding the principles of citizen engagement to analyzing the role of digital technologies...
-
Compatibilization of polymeric composition filled with ground tire rubber – short review
PublikacjaWaste rubber is recognized as valuable materials resource and searching for new recycling methods is the main activity of many research institutions and companies. At the turn of the last years only few scientific papers about foamed polymer compositions filled with ground tire rubber were published. In paper review about progress in compatibilization and foaming of polymeric compositions filled with ground tire rubber.
-
Reliable renewable energy – application of electrochemical capacitors for electrical energy storage
PublikacjaThis paper presents electrical energy storage devices such as electrochemical capacitors, their principle of operation and electrode materials most commonly used in their manufacturing technology. Moreover, our research on development of new nanocomposite materials based on multi-walled carbon nanotubes and conducting polymer is shown. Additionally, the possibility and advantages of application of supercapacitors for accumulation...
-
Determination of the shape of the CFGFT cylindrical column based on laboratory tests
PublikacjaAnalyses were carried out on glass-fibre-reinforced polymer tube columns with reference to laboratory tests. The angles of the glass fibre beams were 20◦, 55◦ and 85◦. The study employed non-classical operational calculus. Various modulated harmonic signal shapes were considered for columns and tubes at buckling. The buckling loads were assessed and compared for different models.
-
On geometrically non-linear FEA of laminated FRP composite panels
PublikacjaThe paper presents a state-of-art review on Finite Element Analysis (FEA) of geometrically non-linear problems for laminated composite plates and shells made as fibre reinforced polymer (FRP) laminates. Besides a subjective overview of the historical development of geometrically non-linear FEA of laminated FRP composite panels, some remarks on possible future issues in this research area are given
-
Interfacial adhesion evaluation in (low-density polyethylene)/elastomer blends
PublikacjaLow-density polyethylene (LDPE) with different elastomers at a ratio of 50/50 wt% blends was prepared by using a co-rotating twin-screw extruder. Three kinds of elastomers were used: ground tire rubber (GTR), partially crosslinked butyl rubber (KalarVR ), and styrenebutadiene- rubber block copolymer (SBS; KratonVR ). For better characterization of interaction between polyethylene and elastomer, influence of the type of elastomer on...
-
Experimental investigation of performance and emission characteristics of a miniature gas turbine supplied by blends of kerosene and waste tyre pyrolysis oil
PublikacjaFossil fuels are non-renewable sources of energy that could be depleted in the near future, giving rise to amajor energy crisis. Scientists from all over the world are working on new technologies to produce fuelnot only from renewable sources but also from waste. This article is concerned with: (i) waste tyremanagement by means of the pyrolysis process, (ii) investigation of physico-chemical parameters ofwaste tyre pyrolysis oil...
-
Preparation and characterisation of solution-cast Nafion membrane
PublikacjaNafion is a commercial name for a perfluorosulfonic polymer, which has been developed in 1962 by Dupont de Nemours. This polymer consists of a polytetrafluoroethylene backbone and regular spaced long perfluorovinyl ether pendant side chains terminated by a sulfonate ionic group. These sulfonate groups are responsible for cation-exchange properties of Nafion. Thanks to the ion-exchange properties, water permeability, good chemical,...
-
Silicon oxycarbide-tin nanocomposite derived from a UV crosslinked single source preceramic precursor as high-performance anode materials for Li-ion batteries
PublikacjaIn this work, we report an innovative and facile UV light-assisted synthesis of a nanocomposite based on silicon oxycarbide (SiOC) and tin nanoparticles. SiOC ceramic matrix, containing a conductive free carbon phase, participates in lithium-ion storage, and buffers the volume changes of Li-alloying/de-alloying material. The reported synthesis procedure through a polymer-derived ceramic route involves the preparation of a single-source...
-
Mechanical properties of PVDF-coated fabric under tensile tests
PublikacjaThis article describes the laboratory tests necessary to identify the mechanical properties of the polyvinylidene fluoride (PVDF)-coated fabrics named Precontraint 1202S and Precontraint 1302S. First, a short survey of the literature concerning the description of coated woven fabrics is presented. Second, the material parameters for PVDF-coated fabrics are specified on the basis of biaxial tensile tests. A comparison of the 1:1...
-
Effect of starch fillers on the dynamic mechanical properties of rubber biocomposite materials
PublikacjaIn the paper the results of dynamic mechanical study of the biocomposites containing one of two types of (potato or corn) strach used as fillers in different amount were discussed. The composites were obtained from rubbery mixture containing natural rubber (NR) as a main component. Thermomechanical analyses (by DMA) showed that the used quantity of strach fillers only slightly influence on the glass transition temperature of vulcanizates.
-
Investigation of volatile low molecular weight compounds formed during continuous reclaiming of ground tire rubber
PublikacjaGround tire rubber was thermo-mechanically reclaimed at different temperature conditions (80, 120, 160 °C) using a co-rotating twin screw extruder. The progress of ground tire rubber reclaiming was evaluated with specific mechanical energy, sol fraction and thermogravimetric analysis. Volatile organic compounds (VOCs) including volatile sulfur compounds (VCSs) released from ground tire rubber and ground tire rubber after reclaiming...
-
Nonlinear viscoelasticity in Three Dimensional filler reinforced rubber composites and nanocomposites
PublikacjaThis chapter describes the influence of three-dimensional nanofillers used in elastomers on the nonlinear viscoelastic properties. In particular, this part focuses and investigates the most important three-dimensional nanoparticles, which are used to produce rubber nanocomposites. The rheological and the dynamic mechanical properties of elastomeric polymers, reinforced with spherical nanoparticles, like POSS, titanium dioxide and...
-
Weldability of pipe grade polyethylenes as realized from thermal and mechanical properties assessments
PublikacjaSince polyethylene (PE) has been widely accepted for the production of high-pressure fluid conveying pipelines, studies devoted to weldability of PE connections were always of major importance. In this study, two industrial PE grades designed for pipe production, namely PE80 and PE100, were injection molded, cut, and then welded as PE100-PE100, PE100-PE80, and PE80-PE80. The heat-welded joints were assessed by differential scanning...
-
Curing characteristics, mechanical and thermal properties of reclaimed ground tire rubber cured with various vulcanizing systems
PublikacjaGround tire rubber was thermo-mechanical reclaimed at 120 °C using a co-rotating twin screw extruder. The effect of vulcanizing system type on curing characteristics, static mechanical properties (tensile strength, elongation-at-break, hardness and resilience), dynamic mechanical properties and thermal properties of reclaimed ground tire rubber was investigated. Reclaimed rubber was cured using different types of vulcanization...
-
Effect of high loading of titanium dioxide particles on the morphology and selected properties of natural rubber-based composites
PublikacjaThe aim of this work was to prepare and characterize the natural rubber vulcanizates contained different amounts of titanium dioxide particles. At first rubber mixture was prepared using a laboratory two-roll mill and then samples were vulcanized in a hydraulic press. The formulation of rubber mixture and rubber-processing technique is based on our earlier investigations. Materials were obtained at the different titanium dioxide...
-
Characterization of volatile compounds, structural, thermal and physico-mechanical properties of cross-linked polyethylene foams degraded thermo-mechanically at variable times
PublikacjaWaste cross-linked polyethylene foam (wXLPE) was thermo-mechanically degraded at variable time using internal batch mixer. The progress of wXLPE degradation has been investigated by using a simultaneous thermogravimetric/differential scanning calorimetry analyzer coupled with Fourier transform infrared spectroscopy, swelling measurements, tensile tests and scanning electron microscopy. Volatile organic compounds generated during...
-
Rheological characteristics of oligomeric semiproducts gained via chemical degradation of polyurethane foam using crude glycerin in the presence of different catalysts
PublikacjaPolyurethane (PU) recycling is a topic of growing interest due to the increasing amount of polyurethane waste. The main purpose of polyurethane chemical recycling is to recover the starting polyol. In this study, a method of polyurethane thermochemical recycling, glycerolysis by means of crude glycerin, is proposed. This work presents a comparative study of commercial catalysts used in order to accelerate the decomposition process,...
-
Microwave radiation in the synthesis of urethane prepolymers
PublikacjaThis paper describes the use of microwave radiation in the synthesis of urethane prepolymers in bulk (without solvent). The prepolymers were synthesized using 1,6-hexamethylene diisocyanate (HDI) and poly (ε-caprolactone) diol (PCL) at a molar ratio of 4:1. The reaction was carried out without a catalyst in the reactor with a conventional heating system (oil bath) or in the microwave reactor (MW Reactor NOVA 09) at temperatures...
-
Preparation and characterization of rigid polyurethane-polyglycerolnanocomposite foams
PublikacjaThis work reports on the preparation of polyurethane-polyisocyanurate (PUR-PIR) foams containing different polyglycerols and layered silicate nanoclays. The rigid polyurethane foams were obtained in a laboratory scale, in a single step method, from a two-component system with a NCO to OH groups ratio equal to two. The reaction mixture consisted of the proper amounts of a commercial oligoetherpolyol, polyglycerol, catalysts, water,...
-
Local impedance spectra of organic coatings
PublikacjaPublikacja przedstawia nowe podejście do lokalnych spektroskopowych pomiarów impedancyjnych powłok organicznych, oparte o mikroskop sił atomowych pracujący w trybie kontaktowym. Pomiędzy nieporuszającą się igłę mikroskopu i podłoże metalowe pokryte powłoką epoksydową przyłożono serię sinusoidalnych napięciowych sygnałów pobudzenia w zadanym zakresie częstotliwości. W ten sposób zarejestrowano lokalne widma w trybie "frequency by...
-
Effect of bio-based components on the chemical structure, thermal stability and mechanical properties of green thermoplastic polyurethane elastomers
PublikacjaIt seems to be obvious that conditions changes during polyols synthesis have impact on the polyols properties. Even the chemical formula is the same or similar, physicochemical properties and also molecular weight of polyols might be different and are significant in term of future polyurethanes properties and processing. In this work, fully bio-based poly(propylene succinate)s synthesized at different temperature conditions were...
-
The influence of amorphous macrodiol, diisocyanate type and l-ascorbic acid modifier on chemical structure, morphology and degradation behavior of polyurethanes for tissue scaffolds fabrication
PublikacjaStudies described in this work were related to the bulk synthesis and characterization of polyurethanes (PURs) obtained with the use of cyclic 4,4′-methylene bis(cyclohexyl isocyanate) (HMDI) or linear 1,6-hexamethylene diisocyanate (HDI), amorphous α,ω-dihydroxy(ethylene-butylene adipate) macrodiol (PEBA), 1,4-butandiol (BDO) chain extender and dibutyltin dilaurate (DBTDL) catalyst. Obtained PURs were modified with l-ascorbic...
-
Effect of molar ratio [NCO]/[OH] groups during prepolymer chains extending step on the morphology and selected mechanical properties of final bio‐based thermoplastic poly(ether‐urethane) materials
PublikacjaThe main aim of this work was to investigate the effect of [NCO]/[OH] molar ratio used during the prepolymer chain extending step (with bio‐based diols) on the chemical structure, and thermomechanical and mechanical properties of thermoplastic poly(ether‐urethane)s. Thermoplastic poly(ether‐urethane)s were obtained from bio‐based polyol (polytrimethylene ether glycol), bio‐based glycol (1,4‐butanediol or 1,3‐propanediol), and 4,4'diphenylmethane...
-
Fully bio-based poly(propylene succinate) synthesis and investigation of thermal degradation kinetics with released gases analysis
PublikacjaOne of the most important information about polyesters is their thermal stability and phase transition tem- peratures. These characteristics give information about the promising behavior of the polyester during proces- sing. In this work, linear bio-based polyester polyols were prepared with the use of succinic acid and 1.3- propanediol (both with natural origin). As a polycondensation catalyst was used tetraisopropyl orthotitanate...
-
Oxygen concentration regulated the efficient liquefaction of vulcanized natural rubber
PublikacjaOxidative liquefaction represents a promising avenue for the homogeneous and high-value utilization of waste tire rubber. Given that truck tires predominantly comprise natural rubber (NR), this study investigated the efficient liquefaction of vulcanized NR regulated by oxygen concentration. Remarkably, the liquefaction of vulcanized NR was realized with an oxygen concentration of 75 % at 200 °C within 3 min. FTIR spectroscopy showed...
-
Degradation of polyurethanes in sea water
PublikacjaOceniono degradowalność różnych poliuretanów w wodzie morskiej Bałtyku. Porównano te dane z wynikami stopnia degradacji poliuretanów w wodzie morskiej z dodatkiem azydku sosowego. Ocenę stopnia degradacji przeprowadzano na podstawie pomiarów zmian masy, właściwości mechanicznych i morfologii przed i po procesie degradacji. Wykazano, że różna podatność na degradację poliuretanów w wodzie morskiej związana jest z ich odmiennym stopniem...
-
Preparation and characterization of rigid polyurethane -polyglycerol nanocomposite foams
PublikacjaThis work reports on the preparation of polyurethane–polyisocyanurate (PUR–PIR) foams containing different polyglycerols and layered silicate nanoclays. The rigid polyurethane foams were obtained in a laboratory scale, in a single step method, from a two-component system with a NCO to OH groups ratio equal to two. The reaction mixture consisted of the proper amounts of a commercial oligoetherpolyol, polyglycerol, catalysts, water,...
-
Linear and branched polyester resins based on dimethyl-2,5-furandicarboxylate for coating applications
PublikacjaIn this study, novel bio-based hydroxyl-functional (co)polyesters from dimethyl-2, 5-furandicarboxylate (DMF), 2,3-butanediol, and a variety of comonomers viz. glycerol, pentaerythritol or trimethylolpropane are prepared using a solvent-free, bulk polycondensation technique. Extensive molecular and thermal characterization was performed to elucidate the properties of these materials. The materials showed suitable properties for solvent-borne...
-
Effect of Compounding Conditions on Static and Dynamic Mechanical Properties of High Density Polyethylene/Ground Tire Rubber Blends
PublikacjaSearching for new and cost-effective methods of waste rubber recycling is a subject of research in many scientific centers in the world. In this paper there are presented results of the research of the extrusion process of cheap and environmentally friendly thermoplastic compositions containing 50 % wt. of masses of ground tire rubber (GTR). The aim of this study was to determine the relationship between the mixing conditions and...
-
Curing characteristics, mechanical properties and morphology of butyl rubber filled with ground tire rubber (GTR)
PublikacjaThe results on testing application of ground tire rubber (GTR), as potential filler for butyl rubber, are pre- sented. The GTR content variation, within the range of 10–90 phr, was studied with respect to the vulcanization process, static mechanical properties (tensile strength, elongation-at-break, hardness and resilience), dynamic mechanical properties and the morphology of the obtained vulcanizates. Butyl rubber was characterized...
-
Rigid polyurethane foams from a polyglycerol-based polyol
PublikacjaRigid polyurethane foams (rPUs) were synthesized by replacing 35 and 70 wt.% of petrochemical polyol with polyglycerol. Two types of polyglycerol with different molecular weights and hydroxyl numbers were used to obtain new ‘‘green’’ polyurethane–polyglycerol foams. The foams were prepared by a single step method for the ratio of NCO/OH groups equal to 2. rPUs synthesized with polyglycerol showed regular cellular structure, with...
-
Synthesis and characterisation of polyurethane elastomers with semi-products obtained from polyurethane recycling
PublikacjaIn this work polyurethane elastomers were synthesised by using different mixtures of a petrochemical and glycerolysate polyols and 4,4-diphenylmethane diisocyanate (MDI). Glycerolysate polyol was produced from polyurethane foam decomposition using crude glycerine as a decomposition agent. The structure and thermal properties of obtained semi-product were similar to the polyol used in the synthesis of original foam. Glycerolysate...
-
Evaluation of structural change during fast transformation process of cross-linked NR into liquid NR by light pyrolysis
PublikacjaThe presence of cross-linked networks in rubber creates a tremendous problem for recycling and reusing of waste rubber. Fast transformation of cross-linked natural rubber (NR) into liquid natural rubber was carried out by light pyrolysis in temperature range from 240 to 300 °C in variable time (in range: 1–30 min). The transformation efficiency was evaluated by measuring the sol fraction and the cross-link density of the gel fraction....
-
Thermoplastic polyurethanes derived from petrochemical or renewable resources: A comprehensive review
PublikacjaThermoplastic polyurethanes (TPUs) materials are obtained by the reaction of polyol (ether-, ester-, and carbonate-based diols with average molecular weight in the range from 1,000 to 3,000 g/mol) with aliphatic or aromatic diisocyanates. Synthesized materials consist of the hard and soft segments which are separated in different level. All mechanical and thermal properties of TPUs depend on the chemical structure of used monomers,...
-
A comparative study on selective properties of Kraft lignin–natural rubber composites containing different plasticizers
PublikacjaEffect of plasticizer type on the kraft lignin–nat- ural rubber composite microstructure and selected proper- ties was determined. The composites were prepared with addition of a commonly used naphthenic oil plasticizer to study the decomposition product of polyurethane (glyc- erolysate) and its characteristics. Kraft lignin powder was incorporated into the natural rubber matrix in amounts of 10 and 40 parts per 100 parts of natural...
-
Elastic polyurethane foams containing graphene nanoplatelets
PublikacjaElastic polyurethane foams were produced from two-component polyurethane systems (SPECFLEX NE 113 izocyjanian/NR 816 poliol system—SPC and Elastic MBMarket company system POLYOL ET MB 500/ISO ET MB 800—ET) by using a one-step method. The foams were a graphene nanoplatelets (GNP) in the amount ranging from 1 to 2 wt.%. The effect of the nanofiller on polyurethane matrix was determined by analyzing the chemical structure, static...
-
Thermoplastic polyurethanes with glycolysate intermediates from polyurethane waste recycling
PublikacjaThe polyol is a major component in polyurethane formulations and therefore introducing to the formulation recycled polyol (obtained during decomposition process) allows decreasing the usage of pure petrochemical components. In this work, thermoplastic polyurethanes were prepared using various mixtures of a petrochemical macrodiol poly(ethylene-butylene adipate)diol (PEBA) and a recycled glycolysate intermediate, called glycolysate...
-
Reactive extrusion of biodegradable aliphatic polyesters in the presence of free-radical-initiators: A review
PublikacjaNowadays, growing attention is being paid to the environment and sustainability, what fully justified research works focused on modification of biodegradable polymers and their composites. In this field of research reactive extrusion seems to be the most promising approach, which fits well to sustainable development strategy. In In the present work, the in-situ modification of biodegradable aliphatic polyesters and the compatibilization...
-
A comprehensive evaluation of flexible FDM/FFF 3D printing filament as a potential material in medical application
PublikacjaThe use of FDM/FFF in 3D printing for medical sciences is becoming common. This is due to the high availability and decent price of both 3D printers and filaments useful for FDM/FFF. Currently, researchers' attention is focused mainly on the study of medical filaments based on PLA, PCL or their modifications. This contributes to insufficient diversity of medical-grade filaments on the market. Moreover, due to the lack of specified...