Wyszukiwarka
Filtry
wszystkich: 7765
-
Katalog
- Publikacje 5580 wyników po odfiltrowaniu
- Czasopisma 47 wyników po odfiltrowaniu
- Konferencje 24 wyników po odfiltrowaniu
- Osoby 82 wyników po odfiltrowaniu
- Wynalazki 2 wyników po odfiltrowaniu
- Projekty 9 wyników po odfiltrowaniu
- Aparatura Badawcza 8 wyników po odfiltrowaniu
- Kursy Online 22 wyników po odfiltrowaniu
- Wydarzenia 4 wyników po odfiltrowaniu
- Dane Badawcze 1987 wyników po odfiltrowaniu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: HIGH SPEED GENERATOR
-
Effect of Pendolino high-speed rail on the structure of buildings located the proximity of the railway tracks
PublikacjaThe following research focuses on the dynamic analysis of the impact of the high-speed train inducted vibrations on the structures located near railway tracks. The office complex chosen as the subject of calculations is located in the northern part of Poland, in Gdańsk, in the proximity of Pendolino, the high speed train route. The high speed trains are the response for the growing needs for more efficient railway system. However...
-
Impact of digital signal processing on FOC current feedback in high-speed PMSM drive
PublikacjaIn applications where size and weight of the electric motor are among major design concerns, Permanent Magnet Synchronous Motors (PMSMs) with wide operational speed-range are commonly preferred. Due to limited inverter switching frequency, high-speed operation of a drive results in a low ratio between the switching frequency and the fundamental frequency of motor voltage. Such operating conditions have been recently identified...
-
Research and analysis of high-speed data transmission radio link designed for maritime environment
PublikacjaIn these article the realization of digital radio link for high-speed data transmission was presented. Its concept and practical realization, using USRP devices from National Instruments, were described. Developed software for generation and reception of digital signals in baseband, including description of modulation types, and time and frequency synchronization mechanisms, was presented. Moreover, an operation of designed radio...
-
Research and Analysis of High-Speed Data Transmission Radio Link Designed for Maritime Environment
PublikacjaIn these article, the realization of digital radio link for high-speed data transmission was presented. Its concept and practical realization, using USRP devices from National Instruments, were described. Developed software for generation and reception of digital signals in baseband, including description of modulation types, and time and frequency synchronization mechanisms, was presented. Moreover, an operation of designed radio...
-
Torque transmission diagnostic system for high-speed train using state-space observer
PublikacjaW artykule przedstawiono zagadnienie diagnostyki czujnika prędkości silnika i przekładni mechanicznej pociągu. W celach diagnostycznych zastosowano obserwatory stanu do obliczania prędkości obrotowej silnika i momentu obciążenia. Analiza chwilowych wartości obliczonej prędkości obrotowej oraz momentu obciążenia pozwala na diagnozowanie stanu układu transmisji momentu trakcyjnego. Zaprezentowano wyniki badań symulacyjnych i eksperymentalnych...
-
FPGA realization of the high-speed residue-to-binary converter based on chinese remainder theorem
PublikacjaW pracy przedstawiono architekturę, realizację FPGA oraz symulację numeryczną na poziomie bitowym szybkiego konwertera z systemu resztowego do systemu binarnego dla modułów 5-bitowych opartego na chińskim twierdzeniu o resztach. Algorytm konwertera obejmuje obliczanie projekcji ortogonalnych poprzez odczyt pamięci oraz sumowanie modulo M realizowane dwustopniowo, pierwszy stopień oparty o sumatory CSA umożliwia redukcję do zakresu...
-
FPGA realization of the high-speed residue-to-binary converter based on the Chinese Remainder Theorem
Publikacja...
-
Tool Life and Process Dynamics in High Speed Ball End Milling of Hardened Steel
Publikacja -
Loss Minimization-Based Sensorless Control of High-Speed Induction Motor Considering Core Loss
PublikacjaThis paper presents loss-minimizing sensorless control (LMC) strategies utilized to optimize the energy of high-speed induction motor (HSIM) drives. A machine’s ability to operate effectively depends on the estimation of its electrical losses. Although copper losses account for the majority of electrical losses in electrical machines, core loss also contributes a major part, particularly in high-speed induction motors. A review...
-
Implementation of high-speed data transmission technological demonstrator using software defined radio technology
PublikacjaIn the article implementation of high-speed data transmission technological demonstrator using software defined radio technology is presented. A system architecture design including asymmetric framing transmission organization, which differs from the ones used in cellular systems is described. The construction of technological demonstrator consisting of management unit, radio unit and programmable multithreaded software performing...
-
Implementation of high-speed data transmission technological demonstrator using software defined radio technology
PublikacjaIn the article implementation of a high-speed data transmission technological demonstrator using software defined radio technology is presented. A system architecture design including asymmetric framing transmission organization, which differs from the ones used in cellular systems is described. The construction of technological demonstrator consisting of a management unit, radio unit and programmable multi-threaded software performing...
-
A novel method for vibration surveillance during high speed ball end milling of flexible details
PublikacjaPraca dotyczy nadzorowania drgań podczas obróbki zakrzywionych przedmiotów podatnych frezem kulistym, z uwzględnieniem zgodności parametrów modelu modalnego. Przedstawiono analizę dynamiki niestacjonarnego okładu drgającego, z którego wydzielono podukład modalny, strukturalny i łączący. Zastosowano minimalizację poziomu drgań z dopasowaniem prędkości obrotowej wrzeciona do optymalnego kąta przesunięcia fazowego. Eksperymenty doświadczalne...
-
A novel method for vibration surveillance during high speed ball end milling of flexible details
PublikacjaPraca dotyczy nadzorowania drgań układów niestacjonarnych modelowanych metodą elementów skończonych. Obróbka frezem kulistym przedmiotów podatnych jest często stosowana w przypadku nowoczesnych centrów obróbkowych. Drgania względne narzędzie-przedmiot obrabiany mogą doprowadzić do utraty stabilności i powstania drgań samowzbudnych typu chatter. W pracy proponuje się metodę minimalizacji poziomu drgań poprzez dopasowanie prędkości...
-
RNS reverse high-speed converter with quasi-regular structure based on the Chinese Remainder Theorem
PublikacjaPrzedstawiono dwie nowe architektury szybkiego konwertera z systemuresztowego do systemu binarnego oparte o chińskie tw. o resztach. Zastosowano nowe struktury 4-operandowych sumatorów modulo 2M. Pierwsza ze struktur oparta jest o wstępne sumowanie najstarszych bitów wektorów sumy i przeniesienia na wyjściu sumatora CSA, natomiast druga o bezpośrednie wykrywanie przekroczenia 2M. Konwerter wykorzystujący drugą ze struktur charakteryzuje...
-
Creation of a map of optimal spindle speeds for a purpose of surveillance of high speed milling of flexible details
PublikacjaDrgania samowzbudne typu chatter często towarzyszą procesom frezowania szybkościowego. Ich skutkiem są nieodwracalne uszkodzenia powierzchni obrabianej. Mogą one również doprowadzić do intensywnego zużycia narzędzi skrawających, a nawet samej obrabiarki. W pracy przedstawiono metodę umożliwiającą tworzenie mapy optymalnych prędkości obrotowych wrzeciona. Stosowanie podczas procesu frezowania optymalnej prędkości obrotowej wrzeciona...
-
Considerations about the applicability of the Reynolds equation for analyzing high-speed near field levitation phenomena
Publikacjaequation for analyzing near field levitation (NFL) phenomena. Two separate approaches were developed, experimentally verified, and applied to meet the research objective. One was based on the Reynolds equation and the other was based on general conservation equations for fluid flow solved using computational fluid dynamic (CFD). Comparing the calculation results revealed that, for certain operating conditions, differences in the...
-
Modeling the impact of rotor movement on non-linearity of motor currents waveforms in high-speed PMSM drives
PublikacjaMotor current measurement techniques as well as predictive control algorithms for electric drives rely on an assumption of linear motor currents changes resulting from constant inverter output voltages. Recent research has reported that this assumption does not hold in motors with short electrical time constant, and in drives whose rotor position advances substantially during a control period. This paper proposes a simulation model...
-
Appliance of High Speed Camera during Industrial Exploitation on the Example of Static and Dynamic Tests of Steel Probes
Publikacja -
Research of low-speed high torque planet motors supplied with oil-in-water emulsion as working liquid.
PublikacjaWiększość hydraulicznych układów napędowych obecnie jest zasilanych olejami. Ale olej jako medium robocze nie może być stosowany wszędzie tam, gdzie istnieje ryzyko pożaru. dlatego też są stosowane trudnopalne i niepalne ciecze hydrauliczne ja: emulsje, mikroemulsje i roztwory. W referacie opisano stanowisko badawcze zaprojektowane i zbudowane w Katedrze Hydrauliki i Pneumatyki PG, przedstawiono wyniki badań hydraulicznego silnika...
-
A Mechatronic System for Building the Map of Optimal Spindle Speeds During High Speed Milling of Flexible Details
PublikacjaW pracy przedstawiono mechatroniczny system tworzenia mapy optymalnych prędkości obrotowych wrzeciona w celu nadzorowania drgań typu chatter podczas frezowania szybkościowego przedmiotów podatnych. System ten składa się z części pomiarowej oraz części obliczeniowej, w której wykorzystuje się oprogramowanie autorskie i komercyjne. Na bazie uogólnionego warunku Liao-Younga utworzono mapy optymalnych prędkości obrotowych wrzeciona,...
-
State-of-the-art framework for high-speed camera and photogrammetric use in geometry evaluation of prestressed concrete failure process
PublikacjaPrestressed structures are a key to the realization of the boldest architectural ideas, regardless of shape complexity, great height and large span. A characteristic feature of the prestressed structure is the better use of concrete material properties by insertion of internal forces. The internal forces are opposed to external loads effects (forces and deformations of structure). Prestressed reinforced concrete beams are characterized...
-
Structure and properties of the Ti+Ti(C,N) coatings obtained in the PVD process on sintered high speed steel
Publikacja -
Modeling the impact of discretizing rotor angular position on computation of field-oriented current components in high speed electric drives
PublikacjaModern drives consist of alternating current electric motors, and the field-oriented control (FOC) of such motors enables fast, precise, and robust regulation of a drive's mechanical variables such as torque, speed, and position. The control algorithm, implemented in a microprocessor, requires feedback from motor currents, and the quality of this feedback is essential to a drive's control properties. Motor phase currents are sampled...
-
High-speed multi-stage gas-steam turbine with flow bleeding in a novel thermodynamic cycle for decarbonizing power generation
PublikacjaIn the global pursuit of sustainable energy and reduced carbon footprints, advances in power generation techniques play a crucial role, not only in meeting the ever-increasing energy demands but also in ensuring that environmental standards are maintained and that the health of our planet is prioritized for future generations. In the ongoing quest for sustainable energy solutions, novel high-speed multi-stage gas-steam turbine...
-
THE INFLUENCE OF HOUSING ARRANGEMENT AND INTERFERENCE ON PRELOAD AND THEORETICAL LIFETIME OF A SYSTEM OF TAPER ROLLER BEARINGS OF A HIGH SPEED SHAFT OF A WIND TURBINE GEARBOX
PublikacjaA system of two taper roller bearings can carry loads with a high ratio of axial load to radial load. Such a system was proposed for a wind turbine gearbox following the poor durability of original bearing design with the aim of increasing durability. Because of size limits, a proposed system is composed of two different taper roller bearings. Standard manufacturers’ catalogues do not provide information on recommended preload...
-
High-Speed Videoendoscopy Enhances the Objective Assessment of Glottic Organic Lesions: A Case-Control Study with Multivariable Data-Mining Model Development
Publikacja -
Volume optimization of high-speed surface-mounted permanent magnet synchronous motor based on sequential quadratic programming technique and analytical solution
Publikacja -
Michał Michna dr hab. inż.
OsobyJest absolwentem Wydziału Elektrycznego Politechniki Gdańskiej (1998). W 2004 r. uzyskał stopień doktora. Od 2004 r. zatrudniony w Katedrze Energoelektroniki i Maszyn Elektrycznych Politechniki Gdańskiej (asystent, adiunkt, starszy wykładowca). W latach 2010-2015 zastępca kierownik katedry. Jego zainteresowania naukowe i dydaktyczne obejmują szerokie spektrum zagadnień związanych z projektowanie, modelowanie i diagnostyką maszyn...
-
Control of the wind turbine generator
PublikacjaWind power system consists of two main parts: wind turbine and electrical generator. Wind turbine converts the energy of the flowing air into mechanical energy, next generator converts this energy into electrical energy that is sent to the power system. These two processes should be realized with maximum efficiency and the following requirements for the control system can be formulated: opti-mal wind power conversion, compensation...
-
Non-Salient Brushless Synchronous Generator Main Exciter Design for More Electric Aircraft
PublikacjaThis paper presents a prototype of high speed brushless synchronous generators (BSG) design for the application in autonomous electric power generation systems (e.g., airplane power grid). Commonly used salient pole field of the main generator part of BSG was replaced with a prototype non-salient pole field. The main objective of the research is an investigation into the advantages and disadvantages of a cylindrical field of the...
-
Comparative Analysis of Salient and Non-Salient Pole Brushless Synchronous Generator for Application in Autonomous Electric Power System
PublikacjaThis paper presents a comparative study of two types of brushless synchronous generator for application in autonomous electric power systems (e.g. airplane power grid). Commercially used salient pole and a prototype non-salient pole high speed multi-pole brushless synchronous generator (BSG) have been presented. Comparative analysis of both types of the generator has been performed. Chosen simulation (using FEM and circuit models)...
-
Feedback Control of Doubly-Fed Generator Connected to Current Source Converter
PublikacjaDoubly-fed induction generator (DFIG) system supplied by current source converter (CSC) is considered in this article. The DFIG can work in two independent modes: AC grid connection and stand-alone mode. The DFIG is connected to the ac grid directly through its stator and the CSC links the rotor side. In this mode, the active and reactive powers of the DFIG must be controlled. This article proposes two control system structures...
-
DESIGN AND THEORETICAL ANALYSIS OF A PROTOTYPE TILTING-PAD RADIAL BEARING WITH ADJUSTABLE CLEARANCE
PublikacjaThe article introduces a design and analysis results of a prototype ORC (organic Rankine cycle) turbo generator rotor assembly of 300kW power, supported by tilting-pad bearings of original design. The calculations were performed for a prototype turbo generator rotor. The shaft of this machine is supported with two radial bearings, lubricated with an unusual lubricant – a low-boiling-point agent. The main objective of the presented...
-
Mathematical and numerical modelling, L, IDE, sem. 01, summer 21/22,(M:00057379)
Kursy OnlineModelling. Optimal control. Modal analysis. High speed milling. Mechatronic design.
-
Sensorless Rotor Position Estimation of Doubly-Fed Induction Generator Based on Backstepping Technique
PublikacjaThis paper proposes a speed observer algorithm for the sensorless control of a doubly-fed induction generator based on classical adaptive backstepping technique. The sensorless control is shown using classic stator field oriented control which is used to active and reactive power control. Performance of the proposed algorithm of a speed observer is validated by simulation and experimental results obtained using a small-rating generator...
-
Technical evaluation of marine auxiliary diesel engine on the basis of parameters synchronous generator
PublikacjaThe article presents a method for evaluating the technical condition of selected structural elements of the reciprocating internal combustion engine driving a synchronous generator. Th results of measurements of the electric generator parameters are the diagnostic information source. On this basis it is possible to determine the instantaneous angular speed marine engine crankshaft which, in turn, is the basis for reasoning about...
-
Application of Thermo-chemical Technologies for Conversion of Associated Gas in Diesel-Gas Turbine Installations for Oil and Gas Floating Units
PublikacjaThe paper considers the issue of thermo-chemical recovery of engine’s waste heat and its further use for steam conversion of the associated gas for oil and gas floating units. The characteristics of the associated gas are presented, and problems of its application in dual-fuel medium-speed internal combustion engines are discussed. Various variants of combined diesel-gas turbine power plant with thermo-chemical heat recovery are...
-
Real-time generator of AIS/ARPA/GPS data
PublikacjaThe paper presents a real-time generator of AIS/ARPA/GPS position data in the standardized NMEA 0183 text format. Position data are produced by a set of various types of ships simulated on the Polish part of the Baltic Sea and are generated on defined IP/UDP addresses and RS-232 ports. In the simulation an extensive set of input parameters is taken into account including the number of particular types of ships, their dimensions,...
-
Koncepcja i symulacja polowa generatora o zmiennej częstotliwości. Zastosowanie w autonomicznych systemach elektroenergetycznych = Conception and field simulations of a variable frequency generator. Application for autonomous power generation system
PublikacjaStreszczenie angielskie: This paper covers a conception and simulation results for a brushless synchronous generator working with variable speed in an autonomous energy generation system (e.g. airplane power grid, hybrid vehicle, micro-CHP). The papers has two parts: presentation of the generator conception used in modern autonomous energy generation systems, and simulation results using filed model elaborated in Flux2D software....
-
Application of wireless communication to small WECS with induction generator
PublikacjaWind energy conversion systems (WECS) seem to be self-evident elements of the future smart grids. Among many generator types the squirrel cage induction generator (SCIG) characterizes robustness and low cost. A full-scale power converter can perform smooth grid connection over wide speed range of multiple-stage geared SCIG. Increasing number of sensors can improve the WECS control and diagnostics but increasing number of thin wires...
-
A NOVEL CONCEPT OF H2/O2 STEAM GENERATOR
PublikacjaThis paper presents an idea of hydrogen utilization to steam generation to drive a turbine and produce electricity or to supply a condenser as an element of heating system. Electrolysis process is considered as a source of hydrogen as well as oxygen. Hydrogen combustion with a stoichiometric ratio of pure oxygen produces steam at very high temperature. Steam temperature can be controlled by mixing the generated steam with liquid...
-
A novel concept of H2/O2 steam generator
PublikacjaThis paper presents an idea of hydrogen utilization to steam generation to drive a turbine and produce electricity or to supply a condenser as an element of a heating system. Electrolysis process is considered as a source of hydrogen as well as oxygen. Hydrogen combustion with a stoichiometric ratio of pure oxygen produces steam at very high temperature. Steam temperature can be controlled by mixing the generated steam with liquid...
-
Zdzisław Kowalczuk prof. dr hab. inż.
OsobyW 1978 ukończył studia w zakresie automatyki i informatyki na Wydziale Elektroniki Politechniki Gdańskiej, następnie rozpoczął pracę na macierzystej uczelni. W 1986 obronił pracę doktorską, w 1993 habilitował się na Politechnice Śląskiej na podstawie pracy Dyskretne modele w projektowaniu układów sterowania. W 1996 mianowany profesorem nadzwyczajnym, w 2003 otrzymał tytuł profesora nauk technicznych. W 2006 założył i od tego czasu...
-
Research of Emergency Modes of Wind Power Plants Using Computer Simulation
PublikacjaThe aim of this study is to investigate changes in the wind power plant energy production parameters under the conditions of sudden wind changes and voltage drop. To achieve these goals, a simulation of operation of wind power plants was performed. Twelve wind turbines with variable rotational speed equipped with a Fuhrländer FL 2500/104 asynchronous double-fed induction generator (DFIG) were used, each with an installed capacity...
-
Nonlinear Control of a Doubly Fed Generator Supplied by a Current Source Inverter
PublikacjaNowadays, wind turbines based on a doubly fed induction generator (DFIG) are a commonly used solution in the wind industry. The standard converter topology used in these systems is the voltage source inverter (VSI). The use of reverse-blocking insulated gate bipolar transistor (RB-IGBT) in the current source inverter topology (CSI), which is an alternative topology, opens new possibilities of control methods. This paper presents...
-
Krzysztof Jan Kaliński prof. dr hab. inż.
OsobyUkończył studia magisterskie na Wydziale Mechanicznym Technologicznym (MT) PG (1980, dyplom z wyróżnieniem). Stopień doktora otrzymał na Wydziale Budowy Maszyn PG (1988, praca wyróżniona), stopień doktora habilitowanego na Wydziale Mechanicznym (WM) PG (2002, praca wyróżniona), a tytuł profesora nauk technicznych – w 2013 r. Od 2015 r. jest profesorem zwyczajnym, a od 2019 r. - profesorem. Obszar jego badań naukowych obejmuje:...
-
Simulation Studies of Control Systems for Doubly Fed Induction Generator Supplied by the Current Source Converter
PublikacjaThe control system for a Doubly Fed Induction Generator (DFIG) supplied by a grid-connected Current Source Converter (CSC) is presented in this paper. Nonlinear transformation of DFIG model to the multi-scalar form is proposed. The nonlinear control strategy of active and reactive power of DFIG is realized by feedback linearization. In the proposed control scheme, the DFIG model and CSI parameters are included. Two Proportional-Integral...
-
Analysis of Organic Rankine Cycle efficiency and vapor generator heat transfer surface in function of the reduced pressure
PublikacjaIn the paper presented is analysis of the influence of reduced pressure on efficiency and heat transfer area of vapor generator of Organic Rankine Cycle (ORC) in case of subcritical and supercritical parameters of operation. Compared are two cases of subcritical and supercritical ORC featuring a similar arrangement of heat source supply and heat removal, that is featuring the same temperatures of working fluid before the turbine,...
-
A Wind Energy Conversion System Based on a Generator with Modulated Magnetic Flux
PublikacjaIn this work, the concept of an energy conversion system for wind turbines based on the modified permanent magnet synchronous generator (PMSG) is presented. In the generator, a pair of three-phase windings is used, one of which is connected in a “star” and the second in a “delta” configuration. At the outputs of both windings, two six-pulse uncontrolled (diode) rectifiers are included. These rectifiers are mutually coupled by a...
-
Mariusz Deja dr hab. inż.
OsobyAdiunkt w Katedrze Technologii Maszyn i Automatyzacji Produkcji. Ukończył w 1993 roku studia wyższe magisterskie na Wydziale Mechanicznym Politechniki Gdańskiej, kierunek: Mechanika i Budowa Maszyn, specjalność: Projektowanie Procesów Technologicznych. Po ukończeniu studiów podjął pracę w Katedrze Technologii Maszyn i Automatyzacji Produkcji, a jego podstawowy obszar działalności naukowej związany był z technologią docierania...