wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: DIRECTIONAL PULSE PROPAGATION
-
Spectral reflectance modeling of ZnO layers made with Atomic Layer Deposition for application in optical fiber Fabry-Perot interferometric sensors
PublikacjaSuitability of zinc oxide (ZnO) layers grown using Atomic Layer Deposition for operation in optical-fiber extrinsic Fabry-Perot sensors is investigated using a numerical model. Reflectance spectra obtained using the developed model indicate that the application of these layers in optical-fiber extrinsic Fabry-Perot sensors is difficult as it may require a source whose spectrum width is about 300 nm. A series of ZnO layers grown...
-
Corrigendum to “Fatigue life improvement using low transformation temperature weld material with measurement of residual stress” [Int. J. Fatigue 164 (2022) 107137]
PublikacjaWelding processes often produce high levels of tensile residual stress. Low transformation temperature (LTT) welding wires utilise phase transformation strains to overcome the thermal contraction of a cooling weld. In this paper, the residual stress within each weld was quantified using the milling/strain gauge method, being the strain change measured as the weldment was milled away. The fatigue tests were conducted under uniaxial...
-
Accurate Post-processing of Spatially-Separated Antenna Measurements Realized in Non-Anechoic Environments
PublikacjaAntenna far-field performance is normally evaluated in expensive laboratories that maintain strict control over the propagation environment. Alternatively, the responses can be measured in non-anechoic conditions and then refined to extract the information on the structure field-related behavior. Here, a framework for correction of antenna measurements performed in non-anechoic test site has been proposed. The method involves automatic...
-
Conditions for Multiple Acquisition of Echoes from Stationary Targets in Successive Transmissions of Active Sonars
PublikacjaIn echolocation, the highest possible number of contacts with a detected target is clearly decisive on the possibilities of echo processing to optimise the estimation of distinctive characteristics of the observed target. In hydrolocation, the slow propagation of acoustic waves in water reduces the number of contacts of echosounders and sonars with detected targets. The article considers model conditions for acquiring multiple...
-
Underwater Acoustic Communications in Time-Varying Dispersive Channels
PublikacjaUnderwater acoustic communication (UAC) system designers tend to transmit as much information as possible, per unit of time, at as low as possible error rate. However, the bit rate achieved in UAC systems is much lower than for wire or radio-communication systems. This is due to disadvantageous properties of the UAC channels, namely the sea and inland waters. Estimation of UAC channel transmission properties is possible within...
-
Path Loss Analysis for the IoT Applications in the Urban and Indoor Environments
PublikacjaThe Internet of Things (IoT) networks concept implies their presence in a various and untypical locations, usually with a disturbed radio signals propagation. In the presented paper an investigation of an additional path loss observed in an underground environment was described. The proposed measurement locations correspond to the operation areas of rapidly growing narrowband IoT (NBIoT) networks, the ones using the Long Term Evolution...
-
Fatigue life improvement using low transformation temperature weld material with measurement of residual stress
PublikacjaWelding processes often produce high levels of tensile residual stress. Low transformation temperature (LTT) welding wires utilise phase transformation strains to overcome the thermal contraction of a cooling weld. In this paper, the residual stress within each weld was quantified using the milling/strain gauge method, being the strain change measured as the weldment was milled away. The fatigue tests were conducted under uniaxial...
-
Preload monitoring in a bolted joint using Lamb wave energy
PublikacjaThe knowledge of the load in prestressed bolted connections is essential for the proper operation and safety of engineering structures. Recently, bolted joints have become an area of intensive research associated with non-destructive diagnostics, in particular in the context of wave propagation techniques. In this paper, a novel procedure of bolt load estimation based on the energy of Lamb wave signals was proposed. Experimental...
-
Rapid design closure of linear microstrip antenna array apertures using response features
PublikacjaA simple yet reliable approach to a rapid design closure of linear antenna array apertures at the electromagnetic (EM)-simulation level is proposed. Our methodology exploits an underlying array factor (AF) model suitably corrected by means of characteristic points (angles and levels) of the radiation pattern of the EM model of the antenna array aperture. This conveniently allows for controlling both the side lobe levels...
-
Reduced-cost constrained miniaturization of wideband antennas using improved trust-region gradient search with repair step
PublikacjaIn the letter, an improved algorithm for electromagnetic (EM)-driven size reduction of wideband antennas is proposed. Our methodology utilizes variable-fidelity EM simulation models, auxiliary polynomial regression surrogates, as well as multi-point response correction. The constraint handling is implicit, using penalty functions. The core optimization algorithm is a trust-region gradient search with a repair step added in order...
-
Block Conjugate Gradient Method with Multilevel Preconditioning and GPU Acceleration for FEM Problems in Electromagnetics
PublikacjaIn this paper a GPU-accelerated block conjugate gradient solver with multilevel preconditioning is presented for solving large system of sparse equations with multiple right hand-sides (RHSs) which arise in the finite-element analysis of electromagnetic problems. We demonstrate that blocking reduces the time to solution significantly and allows for better utilization of the computing power of GPUs, especially when the system matrix...
-
Implicit Space Mapping for Variable-Fidelity EM-Driven Design of Compact Circuits
PublikacjaSpace mapping (SM) belongs to the most successful surrogate-based optimization (SBO) methods in microwave engineering. Among available SM variations, implicit SM (ISM) is particularly attractive due to its simplicity and separation of extractable surrogate model parameters and design variables of the circuit/system at hand. Unlike other SM approaches, ISM exploits a set of preassigned parameters to align the surrogate with the...
-
Expedited Design Closure of Antennas By Means Of Trust-Region-Based Adaptive Response Scaling
PublikacjaIn the letter, a reliable procedure for expedited design optimization of antenna structures by means of trust-region adaptive response scaling (TR-ARS) is proposed. The presented approach exploits two-level electromagnetic (EM) simulation models. A predicted high-fidelity model response is obtained by applying nonlinear frequency and amplitude correction to the low-fidelity model. The surrogate created this way is iteratively rebuilt...
-
Hybrid Technique Combining the FDTD Method and Its Convolution Formulation Based on the Discrete Green's Function
PublikacjaIn this letter, a technique combining the finite-difference time-domain (FDTD) method and its formulation based on the discrete Green's function (DGF) is presented. The hybrid method is applicable to inhomogeneous dielectric structures that are mutually coupled with wire antennas. The method employs the surface equivalence theorem in the discrete domain to separate the problem into a dielectric domain simulated using the FDTD method...
-
Analytical Expression for the Time-Domain Discrete Green's Function of a Plane Wave Propagating in the 2-D FDTD Grid
PublikacjaIn this letter, a new closed-form expression for the time-domain discrete Green's function (DGF) of a plane wave propagating in the 2-D finite-difference time-domain (FDTD) grid is derived. For the sake of its verification, the time-domain implementation of the analytic field propagator (AFP) technique was developed for the plane wave injection in 2-D total-field/scattered-field (TFSF) FDTD simulations. Such an implementation of...
-
Expedited design of microstrip antenna subarrays using surrogate-based optimization
PublikacjaComputationally efficient simulation-driven design of microstrip antenna subarrays is presented. The proposed design approach aims at simultaneous adjustment of all relevant geometry parameters of the subarray, which allows us to take into account the effect of the feeding network on the subarray radiation pattern (in particular, the side lobe level, SLL). In order to handle a large number of variables involved in the design process,...
-
Expedited EM-driven multi-objective antenna design in highly-dimensional parameter spaces
PublikacjaA technique for low-cost multi-objective optimization of antennas in highly-dimensional parameter spaces is presented. The optimization procedure is expedited by exploiting fast surrogate models, including coarse-discretization EM antenna simulations and response surface approximations (RSA). The latter is utilized to yield an initial set of Pareto non-dominated designs which are further refined using response correction methods....
-
Simple 60 GHz Switched Beam Antenna for 5G Millimeter-Wave Applications
Publikacja -
Reliable Greedy Multipoint Model-Order Reduction Techniques for Finite-Element Analysis
PublikacjaA new greedy multipoint model-order reduction algorithm for fast frequency-domain finite-element method simulations of electromagnetic problems is proposed. The location of the expansion points and the size of the projection basis are determined based on a rigorous error estimator. Compared to previous multipoint methods, the quality of the error estimator is significantly improved by ensuring the orthogonality of the projection...
-
Model Correction and Optimization Framework for Expedited EM-Driven Surrogate-Assisted Design of Compact Antennas
PublikacjaDesign of compact antennas is a numerically challenging process that heavily relies on electromagnetic (EM) simulations and numerical optimization algorithms. For reliability of simulation results, EM models of small radiators often include connectors which—despite being components with fixed dimensions—significantly contribute to evaluation cost. In this letter, a response correction method for antenna models without connector,...
-
A Broadband Circularly Polarized Wide-Slot Antenna with a Miniaturized Footprint
PublikacjaThis letter presents a novel and simple feeding technique for exciting orthogonal components in a wide-slot antenna. In this technique, a rectangular bracket-shape parasitic strip is placed at the open end of the straight microstrip line to excite the fundamental horizontal and vertical components of the circular polarization (CP). The proposed technique—when employed in conjunction with the asymmetrical geometry of coplanar waveguide...
-
Implementation of FDTD-Compatible Green's Function on Graphics Processing Unit
PublikacjaIn this letter, implementation of the finite-difference time domain (FDTD)-compatible Green's function on a graphics processing unit (GPU) is presented. Recently, closed-form expression for this discrete Green's function (DGF) was derived, which facilitates its applications in the FDTD simulations of radiation and scattering problems. Unfortunately, implementation of the new DGF formula in software requires a multiple precision...
-
Uniform sampling in constrained domains for low-cost surrogate modeling of antenna input characteristics
PublikacjaIn this letter, a design of experiments technique that permits uniform sampling in constrained domains is proposed. The discussed method is applied to generate training data for construction of fast replacement models (surrogates) of antenna input characteristics. The modeling process is design-oriented with the surrogate domain spanned by a set of reference designs optimized with respect to the performance figures and/or operating...
-
RSS-based DoA Estimation Using ESPAR Antennas and Interpolated Radiation Patterns
PublikacjaIn this letter, it is shown how an algorithm, which employs received signal strength (RSS) values in order to estimate direction-of-arrival (DoA) of impinging signals in wireless sensor network (WSN) nodes equipped with electronically steerable parasitic array radiator (ESPAR) antennas, can easily be improved by applying an interpolation algorithm to radiation patterns recorded in the calibration phase of the DoA estimation process....
-
Simple 2-D Direction-of-Arrival Estimation Using an ESPAR Antenna
PublikacjaIn this letter, it has been shown how an electronically steerable parasitic array radiator (ESPAR) antenna can be used for 2-D direction-of-arrival (DoA) estimation employing received signal strength (RSS) values only. The proposed approach relies on changes in RSS values recorded at the antenna output port observed for different vertical and horizontal directions, while antenna’s main beam sweeps 360° area around the ESPAR antenna. Based...
-
Objective relaxation algorithm for reliable simulation-driven size reduction of antenna structure
PublikacjaThis letter investigates reliable size reduction of antennas through electromagnetic-driven optimization. It is demonstrated that conventional formulation of the design task by direct footprint miniaturization with imposing constraints on electrical performance parameters may not lead to optimum results. The reason is that—in a typical antenna structure—only a few geometry parameters explicitly determine the antenna footprint,...
-
Reliable Multi-Stage Optimization of Antennas for Multiple Performance Figures in Highly-Dimensional Parameter Spaces
PublikacjaDesign of modern antenna structures needs to account for multiple performance figures and geometrical constraints. Fulfillment of these calls for the development of complex topologies described by a large number of parameters. EM-driven tuning of such designs is mandatory yet immensely challenging. In this letter, a new framework for multi-stage design optimization of multi-dimensional antennas with respect to several performance...
-
A Geometrically Simple Compact Wideband Circularly Polarized Antenna
PublikacjaA compact broadband wide-slot circular polarization (CP) antenna is proposed. An inverted L-shape parasitic strip at the open end of a microstrip line extension and a slot modification is applied to attain wideband CP. The advantage of this technique is simplicity which makes it readily re-designable for different frequency bands. To demonstrate the concept, three designs working at different frequencies are obtained. The redesign...
-
A Wideband Corrugated Ridged Horn Antenna with Enhanced Gain and Stable Phase Center for X- and Ku-Band Applications
PublikacjaIn this letter, a structure and design procedure of a novel double-flared conical horn antenna with an improved gain and a stable phase center is presented. The antenna incorporates a hybrid ridged and corrugated structure. A double-ridged section is responsible for ensuring a wideband operation, whereas the corrugated section supports the hybrid mode. The antenna impedance bandwidth (VSWR < 2) is 6 GHz to 20 GHz. Excellent performance...
-
RSS-Based DoA Estimation for ESPAR Antennas Using Support Vector Machine
PublikacjaIn this letter, it is shown how direction-of-arrival (DoA) estimation for electronically steerable parasitic array radiator (ESPAR) antennas, which are designed to be integrated within wireless sensor network nodes, can be improved by applying support vector classification approach to received signal strength (RSS) values recorded at an antenna's output port. The proposed method relies on ESPAR antenna's radiation patterns measured...
-
Feedline Alterations for Optimization-Based Design of Compact Super-Wideband MIMO Antennas in Parallel Configuration
PublikacjaThis letter presents a technique for size reduction of wideband multiple-input-multiple-output (MIMO) antennas. Our approach is a two-stage procedure. At the first stage, the antenna structure is modified to improve its impedance matching. This is achieved through incorporation of an n-section tapered feedline, followed by reoptimization of geometry parameters. Reducing the maximum in-band reflection well beyond the acceptance...
-
Low-Cost Data-Driven Surrogate Modeling of Antenna Structures by Constrained Sampling
PublikacjaFull-wave electromagnetic (EM) analysis has become one of the major design tools for contemporary antenna structures. Although reliable, it is computationally expensive which makes automated simulation-driven antenna design (e.g., parametric optimization) difficult. This difficulty can be alleviated by utilization of fast and accurate replacement models (surrogates). Unfortunately, conventional data-driven modeling of antennas...
-
A structure and simulation-driven design of compact CPW-fed UWB antenna
PublikacjaIn this letter, a structure of a miniaturized ultra-wideband CPW-fed antenna and its design proce-dure are presented. The antenna is a modified version of the design previously proposed in the literature, with additional degrees of freedom introduced in order to improve the structure flexibility. The small size is achieved by executing a rigorous optimization procedure that consists of two stages: (i) smart random search carried...
-
Fast simulation-driven design optimization of UWB band-notch antennas
PublikacjaIn this letter, a simple yet reliable and automated methodology for rapid design optimization of ultra-wideband (UWB) band-notch antennas is presented. Our approach is a two-stage procedure with the first stage focused on the design of the antenna itself, and the secondstage aiming at identification of the appropriate dimensions of the resonator with the purpose of allocating the band-notch in the desired frequency range. For the...
-
Multi-objective antenna design by means of sequential domain patching
PublikacjaA simple yet robust methodology for rapid multiobjective design optimization of antenna structures has been presented. The key component of our approach is sequential domain patching of the design space which is a stencil-based search that aims at creating a path that connects the extreme Pareto-optimal designs, obtained by means of single-objective optimization runs. The patching process yields the initial approximation of the...
-
Rapid EM-driven antenna dimension scaling through inverse modeling
PublikacjaIn this letter, a computationally feasible technique for dimension scaling of antenna structures is introduced. The proposed methodology is based on inverse surrogate modeling where the geometry parameters of the antenna structure of interest are explicitly related to the operating frequency. The surrogate model is identified based on a few antenna designs optimized for selected reference frequencies. For the sake of computational...
-
a novel modified star-triangular fractal (MSTF) monopole antenna for super-wideband applications
Publikacja -
a novel modified star-triangular fractal (MSTF) monopole antenna for super-wideband applications
Publikacja -
Fast EM-driven size reduction of antenna structures by means of adjoint sensitivities and trust regions
PublikacjaIn this letter, a simple yet robust and computationally efficient optimization technique for explicit size reduction of antenna structures is presented. Our approach directly handles the antenna size as the main design objective, while ensuring satisfactory electrical performance by means of suitably defined penalty functions. For the sake of accuracy, the antenna structure is evaluated using high-fidelity EM simulation. In order...
-
A New Expression for the 3-D Dyadic FDTD-Compatible Green's Function Based on Multidimensional Z-Transform
PublikacjaIn this letter, a new analytic expression for the time-domain discrete Green's function (DGF) is derived for the 3-D finite-difference time-domain (FDTD) grid. The derivation employs the multidimensional Z-transform and the impulse response of the discretized scalar wave equation (i.e., scalar DGF). The derived DGF expression involves elementary functions only and requires the implementation of a single function in the multiple-precision...
-
Structure and computationally-efficient simulation-driven design of compact UWB monopole antenna
PublikacjaIn this letter, a structure of a small ultra-wideband (UWB) monopole antenna, its design optimization procedure as well as experimental validation are presented. According to our approach, antenna compactness is achieved by means of a meander line for current path enlargement as well as the two parameterized slits providing additional degrees of freedom that help to ensure good impedance matching. For the sake of reliability, the...
-
Dual-Polarized Wideband Bandpass Metasurface-Based Filter
PublikacjaThis paper presents a novel metasurface-based bandpass filter. The structure is realized by simply patterning a double-sided AD250 substrate, and does not require any vias or insertion of lumped elements. The top layer is an annular- aperture-array with multiple inner conductors, whereas the bottom layer is a first-order Hilbert-curve array. FEM-based simulation results of the filter are obtained using HFSS. The experimental validation...
-
Design and experimental verification of multi-layer waveguide using pin/hole structure
PublikacjaThis study presents a novel technique for minimizing RF leakage in metallic hollow waveguides fabricated using the multilayer split-block method. By integrating a pin/hole wall into the split-block multilayers, a substantial reduction of RF leakage can be achieved while reducing the circuit size and mitigating the performance variations. To validate the proposed approach, a slot antenna fed by single ridge waveguide has been prototyped...
-
Absorbing Boundary Conditions Derived Based on Pauli Matrices Algebra
PublikacjaIn this letter, we demonstrate that a set of absorbing boundary conditions (ABCs) for numerical simulations of waves, proposed originally by Engquist and Majda and later generalized by Trefethen and Halpern, can alternatively be derived with the use of Pauli matrices algebra. Hence a novel approach to the derivation of one-way wave equations in electromagnetics is proposed. That is, the classical wave equation can be factorized...
-
Scattering in a section of ferrite coupled microstrip lines: theory and application in nonreciprocal devices
PublikacjaPrzeprowadzono analizę pełnofalową sekcji sprzężonych ferrytowych linii mikropaskowych wykorzystującą w rozwinięciu pola em fale prowadzone w izotropowych złączach wejściowych sekcji oraz jej fajl ferrytowych. W wyniku określono macierz S sekcji. Przeprowadzono modelowanie własności rozproszenia układu oraz symulację parametrów transmisyjnych układów niewzajemnych projektowanych z wykorzystaniem proponowanego układu ferrytowego.
-
Isolator using a ferrite-coupled-lines gyrator
PublikacjaPrzedstawiono koncepcję nowego typu gyratora wykonywanego poprzez zwarcie lub rozwarcie ferrytowych linii sprzężonych (FCL). Redukując w taki sposób macierz rozproszenia (S) sekcji FCL określono macierz S gyratora oraz procedurę jego projektowania. Poprzez odpowiednie wprowadzenie warstwy rezystywnej do układu gyratora zaprojektowano nowy układ isolatora typu FCL oraz podano metodykę jego projektowania. Koncepcje proponowanych...
-
A Note on Fractional Curl Operator
PublikacjaIn this letter, we demonstrate that the fractional curl operator, widely used in electromagnetics since 1998, is essentially a rotation operation of components of the complex Riemann–Silberstein vector representing the electromagnetic field. It occurs that after the wave decomposition into circular polarisations, the standard duality rotation with the angle depending on the fractional order is applied to the left-handed basis vector...
-
A New Type of Macro-Elements for Efficient Two-Dimensional FEM Analysis
PublikacjaThis letter deals with a model order reduction technique applicable for driven and eigenvalue problems solved using the finite element method (FEM). It allows one to efficiently compute electromagnetic parameters of structures comprising small features that require strong local mesh refinement. The subdomains of very fine mesh are separated from the global domain as so called macro-elements that undergo model reduction. The macro-elements...
-
Tuning a Hybrid GPU-CPU V-Cycle Multilevel Preconditioner for Solving Large Real and Complex Systems of FEM Equations
PublikacjaThis letter presents techniques for tuning an accelerated preconditioned conjugate gradient solver with a multilevel preconditioner. The solver is optimized for a fast solution of sparse systems of equations arising in computational electromagnetics in a finite element method using higher-order elements. The goal of the tuning is to increase the throughput while at the same time reducing the memory requirements in order to allow...
-
Electromagnetic curtain effect and tunneling properties of multilayered periodic structures
PublikacjaArtykuł przedstawia analizę rozpraszania fali elektromagnetycznej na wielowarstwowych strukturach periodycznych. W analizowanych strukturach zaobserwowano efekt tunelowania fali oraz efekt przestrajania pasm zaporowych/przepustowych (efekt kurtyny elektromagnetycznej)