Filtry
wszystkich: 112
Wyniki wyszukiwania dla: REINFORCEMENT, REPAIR OF ASPHALT PAVEMENTS, GEOGRIDS, BEARING LOAD CAPACITY, INTERLAYER BOND
-
Wpływ zastosowania zbrojenia warstw asfaltowych geosyntetykami na nośność remontowanej nawierzchni drogowej – cz. 1
PublikacjaArtykuł prezentuje efekty rozpoczętego i trwającego programu badawczego, którego celem jest poszukiwanie trwałego i skutecznego rozwiązania wzmocnienia nawierzchni lub remontu nawierzchni, jakim jest zbrojenie nawierzchni drogowych w warstwach asfaltowych geosiatkami z włókien szklanych, szklano-węglowych i węglowych wstępnie przesączonych asfaltem. Siatki te zostały wykorzystane jako zbrojenie warstw asfaltowych na fragmencie...
-
Model tests of cast-in-place piles formed by using different types of auger
PublikacjaModel tests are still a popular research tool used to observe and determine the mechanisms of pile-soil interaction. Due to the significant scale effect, the results of model tests performed in the 1g system can only be analysed from the qualitative side. This article describes and presents the results of 1g pile model tests carried out for comparative purposes. There were tested the effectiveness and efficiency of various types...
-
Verification of punching shear outside the shear cap by the direct method
PublikacjaThe proposition of a method to verify the punching resistance for very large supports based on the EN 1992-1-1 standard is described in this paper. The present standard guidelines for the calculation of the punching resistance for large supports are also summarised. The proposed direct method is compared with other standard methods using an example taken from design practice. This method consists of a direct check of the shear...
-
Shear fracture of longitudinally reinforced concrete beams under bending using Digital Image Correlation and FE simulations with concrete micro-structure based on X-ray micro-computed tomography images
PublikacjaThe paper presents experimental and numerical investigations of the shear fracture in rectangular concrete beams longitudinally reinforced with steel or basalt bar under quasi-static three point bending. Shear fracture process zone formation and development on the surface of beams was investigated by Digital Image Correlation (DIC) whereas thorough analyses of 3D material micro-structure, air voids, width and curvature of shear...
-
Analysis of Failure Mechanism in Joints with Positive Eccentricity in CFS Truss
PublikacjaThe paper presents studies concerning the load-bearing capacity of truss joints with a positive eccentricity resulting from the arrangement of geometric members and the failure mechanisms observed in the joints. Based on the previously conducted experimental study, a numerical model of the tested fragment of the CFS truss with eccentricity in the joint was created and validated. All structural details of the tested truss and the...
-
Analysis of pavement structure sensitivity to passage of oversized heavy duty vehicle in terms of bearing capacity
PublikacjaOversized heavy duty vehicles occur in traffic very rarely but they reach extremely high weights, even up to 800 tonne. The detrimental impact of these vehicles on pavement structure is much higher than in case of commercial vehicles that comprise typical traffic, thus it is necessary to assess the sensitivity of pavement structure to passage of oversized vehicles. The paper presents results of sample calculations of load equivalency factor...
-
Experimental investigation of joint with positive eccentricity in CFS truss
PublikacjaDue to technological restrictions, in the case of trusses made of CFS open cross-sections, positive eccentricities in the truss joints have become very frequent. Therefore studies concerning the load-bearing capacity of truss joints with positive eccentricity were undertaken. It was assumed that the resistance of cold-formed steel (CFS) open cross-section truss joints located on compression chords and with positive eccentricity...
-
The Idea of Using Adhesive Bonds in Shaping of Cold-formed Thin-walled Beam-columns
PublikacjaThe chapter concerns the idea of using adhesive bonds in the shaping of cold-formed thin-walled beam-columns. The idea of adhesive-bonded connections is not new but is unlikely to have been used in the design and shaping of thin-walled beam-columns in civil engineering up to date. Metal bar structures, including (due to economic reasons) thin-walled structures, are the most common and effective means to build engineering superstructures/loadbearing...
-
Numerical analysis of pile installation effects in cohesive soils
PublikacjaIn this thesis the empirical equation for radial effective stress calculation after displacement pile installation and following consolidation phase has been proposed. The equation is based on the numerical studies performed with Updated Lagrangian, Arbitrary Lagrangian-Eulerian and Coupled Eulerian-Lagrangian formulations as well as the calibration procedure with database containing world-wide 30 pile static loading tests in cohesive...
-
Effects of full displacement pile installation on the stress and deformation state of surrounding soil: review
PublikacjaSeveral field and model tests have been conducted to investigate the impact of pile installation on bearing capacity. However, little is known about how piles behave during installation, how they interact with the surrounding soil, and how this affects sandy soil properties. This review paper investigates the effect of pile driving on surrounding sandy soil as it compacts sandy soil near to the pile. For this purpose, various related...
-
Osteoblast and bacterial cell response on RGD peptide‐functionalized chitosan coatings electrophoretically deposited from different suspensions on Ti13Nb13Zr alloy
PublikacjaMetallic materials for long-term load-bearing implants still do not provide high antimicrobial activity while maintaining strong compatibility with bone cells. This study aimed to modify the surface of Ti13Nb13Zr alloy by electrophoretic deposition of a chitosan coating with a covalently attached Arg-Gly-Asp (RGD) peptide. The suspensions for coating deposition were prepared in two different ways either using hydroxyacetic acid...
-
Electrophoretic deposition and characterization of composite chitosan/Eudragit E 100 or poly(4-vinylpyridine)/mesoporous bioactive glass nanoparticles coatings on pre-treated titanium for implant applications
PublikacjaTitanium implants are surface-modified to achieve bioactivity and often antibacterial properties. Such surface coatings may increase corrosion degradation and be weakly attached to the substrate. In the present research, biodegradable composite coatings, investigated so far as smart environment-sensitive, slowly releasing silver to the implant neighborhood, were produced as a combination of chitosan (CS) with Eudragit E 100 (EE100)...