Filtry
wszystkich: 152
Wyniki wyszukiwania dla: BOILING
-
Size-exclusion chromatography for the determination of the boiling point distribution of high-boiling petroleum fractions
PublikacjaThe paper describes a new procedure for the determination of boiling point distribution of high-boiling petroleum fractions using size exclusion chromatography with refractive index detector. Thus far, the determination of boiling range distribution by chromatography has been accomplished using simulated distillation with gas chromatography with the flame ionization detection. This study revealed that in spite of substantial differences...
-
Boiling crisis - danger or a must?
PublikacjaW artykule przedstawiono zjawisko kryzysu wrzenia w przepływie. W głównej mierze skupiono się na zjawisku dryout'u podczas przepływu pierścieniowego. W pracy przedstawiono teoretyczny model wysychania filmu cieczowego na ściance wraz z jego modyfikacją w oparciu o model dwurównaniowy zaprezentowany przez Sedlera i Mikielewicza (1981). Model ten opiera się na bilansie cieczy w rdzeniu przepływu i w filmie cieczowym, gdzie głównym...
-
Optimal boiling temperature for ORC installation
PublikacjaW pracy przedstawiono oryinalne kryterium wyznaczania optymalnej temperatury odparowania czynnika w obiegu ORC w postaci równań analitycznych. Pokazano przykład obliczeniowy na bazie R134a, wody i etanolu.
-
Visualization of water boiling in tube bundle
PublikacjaW pracy przedstawiono wyniki wizualizacji, za pomocą systemu laserowego noża świetlnego (PIV), wrzenia cieczy w pęku rur. Wykorzystanie systemu PIV umożliwiło analizę skomplikowanej struktury przepływu cieczy podczas wrzenia, a także wzajemnego oddziaływania pomiędzy sekcją grzejną a wrzącą cieczą.
-
Modelling of heat transfer in flow boiling
PublikacjaW pracy przedstawiono zagadnienia związane z modelowaniem wrzenia w przepływie w kanałach o małej średnicy. Przedstawiono modyfikację rozwijanej przez autorów korelacji umożliwiającej wyznaczanie współczynnika przejmowania ciepła podczas wrzenia w przepływie.
-
Flow and pool boiling on porous coated surfaces
PublikacjaOmówiono wpływ powłoki porowatej na przebieg wrzenia w przepływie i w dużej objętości na przykładzie własnych badań eksperymentalnych.
-
A study of flow boiling heat transfer in minichannels
PublikacjaW pracy przedstawiono badania eksperymentalne wrzenia w przepływie w minikanale o średnicy wewnętrznej 2.3mm i długości 38cm. Uzyskano rozłady temperatury wzdłuż ścianki kanału oraz lokalne współczynniki przejmowania ciepła. Dane skorelowano z korelacją półempiryczną uzyskując zadowalającą zgodność.
-
Modelling of convective heat transfer in flow boiling.
PublikacjaW pracy przedstawiono rozważania dotyczące modelowania przepływu z wrzeniem w zastosowaniu do kanałów o małej średnicy. Stwierdzono,że stosowanie korelacji obowiązujących dla średnic konwencjonalnych nie sprawdza się z praktyką w przypadku małych średnic.
-
Sensitivity study of correlation for flow boiling in tubes.
PublikacjaW referacie skupiono uwagę na szczegółowym zbadaniu wpływu wybranych typów modeli, opisujących współczynnik oporu przepływu oraz współczynnik przejmowania ciepła dla wrzenia w przepływie na korelację dla wrzenia w przepływie ( wyprowadzoną dla rur o konwencjonalnych wymiarach -półempiryczny model Mikielewicza ). Otrzymane wyniki porównano z danymi eksperymentalnymi.
-
Flow boiling of R22 and R134 a in enhanced tubes.
PublikacjaPrzedstawiono wyniki badań wrzenia R22 oraz R134a w rurkach gładkich i o rozwiniętej powierzchni: mikrożebrowanej i śrubowo-formowanej. Podano opis stanowiska badawczego, procedury pomiarowej oraz metody obliczania średniego współczynnika przejmowania ciepła. Omówiono wyniki badań eksperymentalnych na tle danych cytowanych w literaturze, a także w porównaniu do wybranych korelacji.
-
Nucleate pool boiling on porous metallic coatings
PublikacjaPrzedstawiono wyniki systematycznych badań eksperymentalnych przejmowania ciepła podczas wrzenia pęcherzykowego wody destylowanej w stanie nasycenia od płaskich i cylindrycznych powierzchni o specjalnie przygotowanej powierzchni: gładkiej, chropowatej oraz pokrytej warstwą porowatą.
-
Flow and pool boiling on porous coated surfaces
PublikacjaPrzedstawiono wyniki badań eksperymentalnych wrzenia na:a)rurkach i płytkach z powłokami porowatymi o różnej grubości i porowatości, b) rurkach, których jedynie górna część była pokryta powłoką porowatą, c) pęku rur wykonanym z rurek z powłoką porowatą. Zaprezentowano również wyniki pomiarów współczynnika przejmowania ciepła i spadku ciśnienia podczas wrzenia w w przepływie wybranych czynników chłodniczych i ich mieszanin z olejem...
-
Simulation of temperature field in cylindrical boiling heating section
PublikacjaW pracy przedstawiono wyniki obliczeń cylindrycznej sekcji grzejnej. Biorąc pod uwagę geometrię i konstrukcję sekcji grzejnej zaprezentowano rozwiązania pola temperatury dla cylindrycznej sekcji grzejenej. W uzyskaniu rozwiązania posłużono się metodą elementów skończonych.
-
Modelling of flow boiling process in small diameter tubes.
PublikacjaW pracy zastosowano standardową korelację wrzenia w przepływie (wyprowadzoną dla rur o konwencjonalnych wymiarach) do przypadków wrzenia w rurach o małych średnicach. Porównanie wyników obliczeń z danymi literaturowymi wykazało nieużyteczność tej korelacji. Wykazano zatem potrzebę prowadzenia badań podstawowych celem uzyskania korelacji pozwalającej umiejętnie przewidywać warunki wymiany ciepła w kanałach o małych średnicach.
-
Flow boiling of oil-refrigerant mixtures in smooth tubes
PublikacjaPrzedstawiono wyniki badań współczynnika przejmowania ciepła i spadku ciśnienia podczas wrzenia czynników R 22, R 134a i R 407C i ich mieszanin z olejem w rurach gładkich. Opisano procedurę badawczą. Udział masowy oleju w mieszaninie z czynnikiem wynosił 0,1% i 5%. Zaobserwowano negatywny wpływ obecności środka smarnego we wrzącym czynniku chłodniczym.
-
Experimental investigations of R22 flow boiling in enhanced tubes.
PublikacjaPrzedstawiono wyniki badań eksperymentalnych wrzenia R22 podczas wrzenia w przepływie wewnątrz rur o rozwiniętej powierzchni przejmowania ciepła: miedzianej rury niskożebrowanej wewnętrznie, stalowej rury formowanej śrubowo oraz stalowej rury z pokryciem porowatym. Przeprowadzono także badania na dwóch rurach gładkich, o średnicy odpowiadającej maksymalnej średnicy wewnętrznej rur o rozwiniętej powierzchni. Średnie wartości...
-
Boiling heat transfer performance of the thermosiphon heat exchanger
PublikacjaPrzedstawiono wyniki badań eksperymentalnych prototypowego, termosyfonowgo wymiennika ciepła. W szczególności określono wpływ geometrii pęku rur, stanu powierzchni rurek oraz poziomu cieczy w parowniku na wydajność cieplną wymiennika.
-
Flow Boiling in Minigap in the Reversed Two-Phase Thermosiphon Loop
PublikacjaThe paper presents the results of experimental investigations of a model of a heat exchanger featuring a minigap, which is perceived as an evaporator for an inverted thermosiphon. The system works with a single component test fluid. The tested evaporator generates pumping power in the test loop in a way similar to the mammoth pump. The tests regarded a module of the heat exchanger, consisting of a hot leg and a cold leg with the...
-
Pool boiling of water-Cu nanofluid on porous coated tube
PublikacjaPrzedstawiono wyniki pomiarów współczynnika przejmowania ciepła podczas wrzenia nanocieczy woda-Cu na poziomej rurce pokrytej aluminiową powłoka porowatą o grubości 0.15 mm i porowatości ok. 40%. Koncentracja nanocząstek wynosiła 0.01%, 0.1% oraz 1%. Badania wykonano dla trzech wartości ciśnienia wrzenia: 200 kPa, 100 kPa oraz 10 kPa.
-
Heat transfer during pool boiling on smooth tube bundle
PublikacjaPrzedstawiono wyniki pomiarów współczynnika przejmowania ciepła dla pęku 19 gładkich rurek ze stali nierdzewnej ogrzewanych elektrycznie podczas wrzenia wody destylowanej, metanolu i R141b. Zaproponowano równanie korelacyjne do obliczania średniego współczynnika przejmowania ciepła.
-
Horizontal flow boiling of refrigerants inside porous coated tube.
PublikacjaPrzedstawiono wyniki badań przejmowania ciepła i spadku ciśnienia podczas wrzenia czynników chłodniczych R22, R134a i R407C w poziomej rurce z wewnętrzną powłoką porowatą.
-
Nucleate pool boiling modelling and experimental investigation : chapter 7
PublikacjaOmówiono wpływ powłoki porowatej nanoszonej na całą powierzchnię rurki lub jej fragment na osiągany współczynnik przejmowania ciepła, krytyczne gęstości strumienia ciepła, a także obwodowy rozkład temperatury przy wrzeniu pęcherzykowym na zewnętrznej powierzchni poziomej rurki.Przedstawiono wyniki badań częstotliwości odrywania się pęcherzyków oraz pól prędkości wokół wzrastającyh i unoszących się pęcherzyków przy wrzeniu z pojedynczych...
-
Improved correlation for modelling of boiling processes in small diameter tubes.
PublikacjaW pracy przedstawiono rozważania na temat wrzenia w przepływie dwufazowym w kanałach o małej średnicy. Modyfikacji uległa korelacja zapostulowana wcześniej przez Mikielewicz i inni, poprzez wprowadzenie efektów związanych z napięciem powierzchniowym, także liczba konwekcyjna została poprawiona. Zastosowanie korelacji jest bardzo proste z uwagi na jej analityczną postać, co jest jej podstawową zaletą. Porównanie z danymi eksperymentalnymi...
-
Experimental study of boiling heat transfer in the stagnation point of water microjet
PublikacjaIn the paper presented is a comparison of computational model with experimental data. Numerical model of liquid film with phase change in the stagnation zone due to impingement of the microjet is more widely presented in authors previous work. The radius on which theevaporation process is taking place can be determined from the energy balance on the element of the plate. That radius has also been confirmed experimentally in the...
-
Pool boiling of nanofluids on rough and porous coated tubes: experimental and correlation
PublikacjaThe paper deals with pool boiling of water-Al2O3 and water- Cu nanofluids on rough and porous coated horizontal tubes. Commercially available stainless steel tubes having 10 mm outside diameter and 0.6 mm wall thickness were used to fabricate the test heater. The tube surface was roughed with emery paper 360 or polished with abrasive compound. Aluminium porous coatings of 0.15 mm thick with porosity of about 40% were produced by...
-
Pressure drop and heat transfer during boiling and condensation at subcritical region
PublikacjaMost of the data presented in the literature relate to saturation temperatures in the range - 20°C to 40°C due to the application in refrigeration technology. There is necessity to extend databases to higher values of saturation temperature due to new applications such as Organic Rankine Cycle and high temperature heat pumps. Only few papers contain data for high reduced pressure for low boiling point liquids. This paper focus...
-
Design analysis of Tesla micro-turbine operating on a low-boiling medium
PublikacjaThis paper presents results of the design analysis of a Tesla bladeless turbine intended for a co-generating micro-power plantof heat capacity 20 kW, which operates in an organic Rankine cycle on a low-boiling medium. Numerical calculations of flowin several Tesla turbine models were performed for a range of design parameters. Results of investigations exhibit interestingfeatures in the distribution of flow parameters within the...
-
Flow boiling intensification in minichannels by means of mechanical flow turbulising inserts
PublikacjaThe work presents the results of experimental investigation on heat transfer in minichannels. Refrigerant R123 was used as a test fluid. Single vertical silver tubes of 380 mm length and 2.3 mm diameter were examined with two variants of turbulising inserts. A wide range of parameters was considered, namely mass flux G=534-3011 kg/(m2s), heat flux qw=28.5-68.4 kW/m2, saturation temperature Tsat=23-86 stC and the full range of vapour...
-
Pool boiling of water-Al2O3 nanofliud on horizontal porous coated tube
PublikacjaPrzedstawiono wyniki badań przejmowania ciepła podczas wrzenia w dużej objętości nanocieczy woda-Al2O3 na poziomej rurce z aluminiową powłoką porowatą o grubości 0.15 mm i porowatości 40%. Koncentracja nanocząstek wnosiła 0.01%, 0.1% oraz 1%. Niezależnie od koncentracji współczynnik przejmowania ciepła przy wrzeniu nanocieczy był niższy niż przy wrzeniu wody destylowanej.
-
Investigation of R 22 and R 134a flow boiling in enhanced tubes
PublikacjaPrzedstawiono wyniki pomiarów współczynnika przejmowania ciepła i spadków ciśnienia podczas wrzenia w przepływie R22 oraz R134a. Do badań użyto dwie rurki o rozwiniętej wewnętrznej powierzchni, tj. rurkę śrubowo-formowaną i rurkę niskożebrowaną oraz dwie rurki gładkie, jako rurki referencyjne. Eksperymenty przeprowadzono przy temperaturze nasycenia ok. zero stopni Celsjusza i końcowym stopniu suchości ok. 0.7. Wyniki badań eksperymentalnych...
-
Experimental Investigations On The Momentum Pressure Drop During Flow Boiling Of R134a
PublikacjaThe article presents experimental investigations of the pressure drop during twophase flow. Experiments were performed for both adiabatic and heated flow of R134a. Obtained flow patterns were compared with the literature. Obtained data is used to validate momentum pressure drop predictions, a set of graphs showing comparisons, for a representative set of experimental conditions, of the two-phase frictional pressure gradients for...
-
An improved method for flow boiling heat transfer with account of the reduced pressure effect
PublikacjaIn the paper are presented the results using the authors own model to predict heat transfer coefficient during flow boiling. The model has been tested against a large selection of experimental data to investigate the sensitivity of the in-house developed model. In the work are presented the results of calculations obtained using the semi-empirical model on selected experimental flow boiling data of the refrigerants: R134a, R1234yf,...
-
A simplified energy dissipation based model of heat transfer for subcooled flow boiling
PublikacjaIn the paper a model is presented based on energetic considerations for subcooled flow boiling heat transfer. The model is the extension of authors own model developed earlier for saturated flow boiling and condensation. In the former version of the model we used the heat transfer coefficient for the liquid single-phase as a reference level, due to the lack of the appropriate model for heat transfer coefficient for the subcooled...
-
The effect of reduced pressure on carbon dioxide flow boiling heat transfer in minichannels
Publikacja. In the paper presented are the results of the study on the effect of reduced pressure on flow boiling heat transfer data in minichannels as well as conventional ones. That effect renders that most of heat transfer correlations fail to return appropriate results of predictions. Mostly they have been developed for the reduced pressures from the range 0.1-0.3. The special correction has been postulated to the in-house model of flow...
-
Thermal performance of a prototype plate heat exchanger with minichannels under boiling conditions
PublikacjaTo solve the problem and to meet the requirements of customers in the field of high heat fluxes transfer in compact units, a new design of plate heat exchanger with minichannels (minichannels PHE) was proposed. The aim was to construct a compact heat exchanger of high effectiveness for the purpose of household cogeneration ORC system. In this paper the experimental analysis of an assembled prototype of such compact heat exchanger...
-
Modelling study of flow boiling heat transfer of perspective fluids for refrigeration technology
PublikacjaThere is a gap of knowledge on flow boiling at high saturation temperatures and higher values of reduced pressure. Thus far, the in-house developed semi-empirical model for flow boiling and flow condensation showed a satisfactory accuracy for calculations for various refrigeration fluids for a wide scope of reduced pressures. This study presents results of calculations of heat transfer coefficient of perspective refrigeration fluids,...
-
Prediction of flow boiling heat transfer data for R134a, R600a and R290 in minichannels
PublikacjaIn the paper presented is the analysis of the results of calculations using a model to predict flow boiling of refrigerants such as R134a, R600a and R290. The latter two fluids were not used in development of model semiempirical correction. For that reason the model was verified with present experimental data. The experimental research was conducted for a full range of quality variation and a relatively wide range of mass velocity....
-
Experimental and theoretical study of flow boiling and dryout phenomenon of ethanol in vertical minitubes
PublikacjaW ramach przeprowadzonych prac zaadoptowano istniejące stanowisko do badań laminarnej konwekcji wymuszonej, wrzenia w przepływie oraz wysychania filmu cieczy na ściance kanału wykorzystując etanol jako płyn roboczy. Przeprowadzono systematyczne badania wrzenia w przepływie dla dwóch średnic rur, tj. 1.15mm i 2.3mm. W badaniach wykorzystano najnowsze osiągnięcia z zakresu technik termowizyjnych celem znalezienia dokładnej lokalizacji...
-
Pool boiling of water-Al2O3 and water-Cu nanofluids on horizontal smooth tubes
PublikacjaPrzedstawiono wyniki pomiarów współczynnika przejmowania ciepła podczas wrzenia dwóch nanocieczy, tj. woda-Al2O3 i woda-Cu o trzech koncentracjach masowych nanocząstek: 0.01%,0.1% oraz 1% na poziomych gładkich rurkach ze stali nierdzewnej i miedzi o średnicy zewnętrznej 10 mm.
-
Low-Pressure Injection of Water and Urea-Water Solution in Flash-Boiling Conditions
Publikacja -
Modelling of temperature field of flat boiling section with active single nucleation site
PublikacjaZaprezentowano główne założenia wybranych modeli wrzenia dla pojedynczego centrum nukleacji. Przedstawiony model numeryczny dotyczy zagadnienia dwuwymiarowego, osiowo-symetrycznego, nieizotropowego przewodzenia ciepła dla warunków brzegowych pierwszego, drugiego i trzeciego rodzaju. Warunek brzegowy drugiego rodzaju reprezentuje gęstość strumienia ciepła połączoną z generacją pęcherzy z pojedynczego centrum nukleacji.
-
Horizontal flow boiling of R22, R134a and their mixtures with oil in smooth and enhanced tubes
PublikacjaOpisano stanowisko i procedurę badawczą. Przedstawiono wyniki badań wrzenia czynników R 22 i R 134a oraz ich mieszanin z olejem wewnątrz dwóch rur gładkich i dwóch rur o rozwiniętej powierzchni. Zweryfikowno wybrane korelacje współczynnika przejmowania ciepła podczas wrzenia czystych czynników chłodniczych w rurach gładkich.
-
Pool boiling of water-Al2O3 and water-Cu nanofluids on horizontal smooth tubes
PublikacjaPrzedstawiono wyniki badań eksperymentalnych wrzenia dwóch nanocieczy woda-Al2O3 i woda Cu na poziomych gładkich rurkach stalowych i miedzianych. Koncentracja nanoicząstek wynosiła 0.01%, 0.1% oraz 1%.
-
Influence of pressure on heat transfer during pool boiling on smooth tube bundle
PublikacjaPrzedstawiono wyniki badań eksperymentalnych wrzenia wody, metanolu i R141b na pęu rur głądkich w warunkach podcisnienia i ciśnienia atmosferycznego
-
Chapter 1. Modelling of temperature field of cylindrical pool boiling heating section
PublikacjaPoddano analizie fundamentalny problem określania temperatury powierzchni, na której zachodzi wrzenie. Rozpatrzono dwa przypadki ogrzewania sekcji: z zastosowaniem grzejnika patronowego oraz użyciem sekcji jako elementu oporowego. Sformułowano i rozwiązano zagadnienia brzegowe 1D, 2D ORAZ 3D. Przedstawiono wyniki obliczeń numerycznych z zastosowaniem MES.
-
Flow boiling of R22, R134a and R 407C inside horizontal smooth tubes.
PublikacjaPrzedstawiono wyniki badań współczynnika przejmowania ciepła i spadku cisnienia podczas wrzenia czynników R22, R134a i R407C w rurach gładkich, wykonanych z miedzi i ze stali nierdzewnej.Opisano stanowisko i procedurę badawczą. Temperatura wrzenia wynosiła 0 st.C, stopień suchości na wlocie do odcinka pomiarowego był równy O, a na wylocie 0,7. Badania prowadzono w zakresie gestości strumienia masy od 250 do 500 kg/m2s. Zaobserwowano...
-
Influence of porous coating on heat transfer during R22 and R134a flow boiling.
PublikacjaPrzedstawiono wpływ powłoki porowatej na przenoszenie ciepła i spadku ciśnienia podczas wrzenia w przepływie czynników chłodniczych, R22 i R134a.
-
Pool Boiling of Water–Al2O3 and Water–Cu Nanofluids Outside Porous Coated Tubes
PublikacjaThis paper deals with pool boiling ofwater–Al2O3 and water–Cu nanofluids on porous coated, horizontal tubes. Commercially available stainless-steel tubes having 10 mm outside diameter and 0.6 mm wall thickness were used to fabricate a test heater. Aluminum porous coatings 0.15 mm thick with porosity of about 40% were produced by plasma spraying. A smooth tube served as a reference tube. The experiments were conducted under different...
-
COMPARISON OF HEAT TRANSFER CHARACTERISTICS IN SURFACE COOLING WITH BOILING MICROJETS OF WATER, ETHANOL AND HFE7100
PublikacjaThe basis of microjet technology is to produce laminar jets which when impinging the surface have a very high kinetic energy at the stagnation point. Boundary layer is not formed in those conditions, while the area of film cooling has a very high turbulence resulting from a very high heat transfer coefficient. Applied technology of jet production can result with the size of jets ranging from 20 to 500μm in breadth and 20 to 100μm...
-
A semi-empirical model for flow boiling heat transfer with account of the reduced pressure effect
PublikacjaIn the present study the attention was focused on the influence of reduced pressure on the predictions of heat transfer during flow boiling at the extensive range of pressures. The results of calculations were to test the sensitivity of the in-house flow boiling model with respect to the selection of the appropriate two-phase flow multiplier, which is one of the distinctive elements of that model. For this purpose a few two-phase...
-
Non-adiabatic Effects in Pressure Drop Calculations in Flow Boiling and Flow Condensation in Minichannels
PublikacjaConsiderations presented in the paper relate both to the case of flow boiling and flow condensation in conventional channels as well as small diameter ones. Authors devoted all the possible attention that the modeling presented is applicable to the whole range of quality variation in both cases of condensation and boiling. The form of two-phase flow multiplier, which is a major factor in modeling presented here, should be capable...
-
A simplified energy dissipation based model of heat transfer for post-dryout flow boiling
Publikacjamodel for post dryout mist flow heat transfer is presented based on considerations of energy dissipation in the flow. The model is an extension of authors own model developed earlier for saturated and subcooled flow boiling. In the former version of the model the heat transfer coefficient for the liquid singlephase convection as a reference was used, due to the lack of the appropriate model for heat transfer coefficient for the...
-
A new procedure for the determination of distillation temperature distribution of high-boiling petroleum products and fractions
PublikacjaThe distribution of distillation temperatures of liquid and semi-fluid products, including petroleum fractions and products, is an important process and practical parameter. It provides information on properties of crude oil and content of particular fractions, classified on the basis of their boiling points, as well as the optimum conditions of atmospheric or vacuum distillation. At present, the distribution of distillation temperatures...
-
Prediction of flow boiling heat transfer coefficient for carbon dioxide in minichannels and conventional channels
PublikacjaIn the paper are presented the results of calculations using authors own model to predict heat transfer coefficient during flow boiling for carbon dioxide. The experimental data from various researches were scrutinised conducted for a full range of quality variation and wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house model. The work shows the importance of taking into account surface...
-
Prediction of flow boiling heat transfer coefficient for carbon dioxide in minichannels and conventional channels
PublikacjaIn the paper presented are the results of calculations using authors own model to predict heat transfer coefficient during flow boiling of carbon dioxide. The experimental data from various resea rches were collected. Calculations were conducted for a full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house model. The results show the importance of taking into...
-
Experimental study and comparison with predictive methods for flow boiling heat transfer coefficient of HFE7000
PublikacjaThis article describes an experimental study of flow boiling of HFE7000 inside a smooth vertical channel. The investigation has been carried out in a circular stainless-steel tube with an inner diameter of 2.3 mm. The data have been collected for the applied heat fluxes q ranging from 61 to 205 kW/m2, the mass flux G ranging from 214 to 1006 kg/(m2 s), the saturation temperature Tsat ranging from 30 to 54 °C and the full range...
-
Flow distribution and heat transfer in minigap and minichannel heat exchangers during flow boiling
PublikacjaThe topic of boiling heat transfer in miniscale geometries has focused the ever increasing interest of researchers in recent years. However, most of the works are related to mini- and microchannels and much less to minigaps. Meanwhile, minigaps allow for more comprehensive experimental studies, i.e. flow visualisations due to the flat, two-dimensional configuration of the flow. The results of the experimental investigations of...
-
Thermal-hydraulic issues of flow boiling and condensation in organic Rankine cycle heat exchangers
PublikacjaW pracy przedstawiono szereg zagadnień cieplno-przepływowych podczas wrzenia i kondensacji w przepływie w wymiennikach ciepła obiegu ORC. Uwzględniono przemiany fazowe. Analizowano zagadnienia stabilności pracy wymienników oraz ich dynamikę
-
Comparison of heat transfer characteristics in surface cooling with boiling microjets of water, ethanol and HFE7100
PublikacjaThe basis of microjet technology is to produce jets which impinge the surface at the stagnation point with a very high kinetic energy. Main objective of this paper was to investigate the physical phenomena occurring on solid surfaces upon impingement of the single microjet in case of three fluids, namely water, ethanol and HFE7100. Intense heat transfer in the impact zone of microjet has been examined and described with precise...
-
Circumferential temperature distribution during pool boiling of R 141b onhorizontal modified tubes.
PublikacjaZaproponowano własną bierną, metodę intensyfikacji przejmowania ciepła w obszarze górnej tworzącej rurki w celu zminimalizowania obwodowego rozkładu temperatury. Metoda polega na naniesieniu aluminiowej warstwy porowatej tylko na części powierzchni rurki - właśnie w obszarze górnej tworzącej.
-
Influence of porous coating on heat transfer during flow boiling of R22, R134a and R407C
PublikacjaPrzedstawiono wpływ pwłoki porowatej w pozionej rurce podczas wrzenia w przepływie i spadku ciśnienia czynników chłodniczych R22, R134a i R407C.
-
The effect of boiling in a thermosyphon on surface tension and contact angle of silica and graphene oxide nanofluids
Publikacja -
Determination of dryout localization using a five-equation model of annular flow for boiling in minichannels
PublikacjaDetailed studies have suggested that the critical heat flux in the form of dryout in minichannels occurs when the combined effects of entrainment, deposition, and evaporation of the film make the film flow rate go gradually and smoothly to zero. Most approaches so far used the mass balance equation for the liquid film with appropriate formulations for the rate of deposition and entrainment respectively. It must be acknowledged...
-
Nucleate pool boiling heat transfer from small horizontal smooth tube bundles
PublikacjaPrzedstawiono wyniki pomiarów współczynnika przejmowania ciepła podczas wrzenia wody destylowanej, metanolu i R141b na poziomym pęku rur gładkich, który składał się z 19 rurek, ogrzewanych elektrycznie, w układzie przestawionym i podziałce 1.7d oraz 2.0d. Wyznaczono również wartości współczynnika wpływu pęku. Podano równanie korelacyjne do obliczania średniego współczynnika przejmowania ciepła
-
Comparitive study of heat transfer and pressure drop during flow boiling and flow condensation in minichannels
PublikacjaIn the paper a method developed earlier by authors is applied to calculations of pressure drop and heat transfer coefficient for flow boiling and also flow condensation for some recent data collected from literature for such fluids as R404a, R600a, R290, R32,R134a, R1234yf and other. The modification of interface shear stresses between flow boiling and flow condensation in annular flow structure are considered through incorporation...
-
Effect of asymmetric fluid flow distribution on flow boiling in a microchannel heat sink – An experimental investigation
PublikacjaFlow boiling in microchannels is emerging as an exclusive cooling solution for miniaturized high-power electronic devices alongside having other high heat flux applications. Size miniaturization at microscale strangely increases heat transfer performance as well as flow boiling instabilities. Many flow boiling instabilities are interrelated and result from imperfect hydrodynamic conditions. One of such problems is flow maldistribution among...
-
Flow boiling of R1233zd(E) in a 3 mm vertical tube at moderate and high reduced pressures
PublikacjaThe results of flow boiling of R1233zd(E) in a 3 mm vertical stainless steel tube are presented at moderate and high saturation temperatures. Integral flow characteristics in the form of pressure drop and heat transfer coefficient are discussed for saturation temperatures ranging from 115 to 145 °C (corresponding reduced pressures from 0.2 to 0.7), mass velocity of 800 kg/m2s and heat flux of 20 kW/m2. All of the obtained heat...
-
Calculation method for flow boiling and flow condensation of R134a and R1234yf in conventional and small diameter channels
PublikacjaThe paper presents the results of calculations performed using the authors’ model to predict the heat transfer coefficient during flow boiling for two refrigerants R134a and R1234yf. The experimental data from various past studies have been collected and the calculations have been conducted for the full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house...
-
EXPERIMENTAL VERIFICATION OF THE METHOD OF FLOW BOILING AND FLOW CONDENSATION HEAT TRANSFER PREDICTION FOR SELECTED FLUIDS
PublikacjaIn the paper presented are the results of calculations using authors own model to predict heat transfer coefficient during flow boiling of different refrigerants. The experimental data from various research studies from literature were collected. Calculations were conducted for a full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in- house developed model....
-
A new method for determination of flow boiling heat transfer coefficient in conventional diameter channels and minichannels
PublikacjaW pracy przedstawiono rozważania związane z modelowaniem wrzenia w przepływie w kanałach o średnicach konwencjonalnych, małych i minikanałach. Przedstawiono przegląd podejść do modelowania wymiany ciepła i w tym świetle przedstawiono oryginalne podejście autora. W przeciwieństwie do innych podejść metoda autora ma zastosowanie zarówno do kanałów o średnicach konwencjonalnych i minikanałach. Przedstawiono zadowalające porównania...
-
Circumferential temperature distribution during nucleate pool boiling outside smooth and modified horizontal tubes
PublikacjaPrzedstawiono wyniki badań eksperymentalnych obwodowego rozkłądu temperatury w poziomych rurkach, ogrzewanych elektrycznie na których zachodzi wrzenie pęcherzykowe. Wykazano, że lokalne - w obszarze górnej tworzącej rurki, zastosowanie powłki porowatej prowadzi do wygładzenia rozkładu temperatury oraz obniżenia średniej temperatury ścianki.
-
Influence of wall temperature on heat transfer coefficient during R 22 boiling in microfin tube
PublikacjaPrzedstawiono wyniki badań współczynnika przejmowania ciepła i spadku ciśnienia podczas wrzenia czynnika R 22 w rurze nisko żebrowanej. Opisano stanowisko i procedurę badawczą. Zaobserwowano spadek współczynnika przejmowania. Opisano stanowisko i procedurę badawczą. Zaobserwowano spadek współczynnika przejmowania ciepła wraz ze wzrostem temperatury ścianki rury.
-
A semi-empirical method for calculation of heat transfer coefficient in flow boiling for conventional tubes and minichannels
PublikacjaW pracy przedstawiono zagadnienia któe należy uwzględnić podczas modelowania wymiany ciepła z wrzeniem w przepływie w kanałach o małej średnicy. Uzyskano dobrą zgodność z wynikami badań eksperymentalnych.
-
A semi-empirical method for calculation of heat transfer coefficient in flow boiling for conventional tubes and minichannels
PublikacjaW pracy przedstawiono zagadnienia które należy uwzględnić podczas modelowania wymiany ciepła z wrzeniem w przepływie w kanałach o małej średnicy. Uzyskano dobrą zgodność z wynikami badań eksperymentalnych.
-
Experimental validation of pressure drop models during flow boiling of R134a – effect of flow acceleration and entrainment
PublikacjaA crucial step to assure proficient work of power and process apparatus is their proper design. A wide array of those devices operates within boiling or condensation of the working fluid to benefit from high heat transfer rates. Two-phase flows are associated with high heat transfer coefficients because of the latent heat of evaporation and high turbulence level between the liquid and the solid surface. Predicting heat transfer...
-
Modelling of saturated, subcooled and post-dryout flow boiling with the energy dissipation based semi-empirical model
PublikacjaA comprehensive semi-empirical model for saturated, subcooled and post dryout heat transfer is presented based on considerations of energy dissipation in the flow. The fundamental hypothesis in the model is the fact that heat transfer during flow boiling can be treated as a sum of two contributions constituting the total energy dissipation in the flow, namely the energy dissipation due to the shearing flow without the bubbles and...
-
Heat Transfer During Pool Boiling of Water, Methanol and R141b on Porous Coated Horizontal Tube Bundles
PublikacjaThis paper presents the results of experimental investigation of water, methanol and R141b refrigerant boiling on horizontal porous coated tube bundles supposed to represent a flooded-type evaporator. Experiments were carried out for a bundle of 19 tubes in triangular layout for two pitch-to-diameter ratio values – 1.7 and 2.0 – in atmospheric and sub-atmospheric pressure conditions. Average heat transfer coefficients – both local,...
-
Comparison of predictive methods for flow boiling heat transfer in conventional channels and minichannels - the effect of reduced pressure
PublikacjaIn the paper are presented the results of follow on studies from [1]–[3] using authors own model to predict heat transfer coefficient during flow boiling. The model has been tested against a large selection of experimental data collected from various researchers to investigate the sensitivity of the in-house developed model. The collected experimental data came from various studies from literature and were conducted for the full...
-
The importance of individual spray properties in performance improvement of a urea-SCR system employing flash-boiling injection
PublikacjaThe appropriate mixing of a urea–water solution (UWS) with exhaust gases in a selective catalytic reduction system is crucial to efficiently reduce nitrogen oxides and diminish the deposition of liquid wall film. One of the methods to enhance the mixing of the UWS with the exhaust gases is a flash-boiling injection. Its positive effect has been linked with a reduced Sauter mean diameter (SMD) and improved evaporation, but the...
-
COMPARISON OF PREDICTIVE METHODS FOR FLOW BOILING HEAT TRANSFER IN CONVENTIONAL CHANNELS AND MINICHANNELS – THE EFFECT OF REDUCED PRESSURE
PublikacjaIn the paper are presented the results of follow on studies from [1]–[3] using authors own model to predict heat transfer coefficient during flow boiling. The model has been tested against a large selection of experimental data collected from various researchers to investigate the sensitivity of the in-house developed model. The collected experimental data came from various studies from literature and were conducted for the full...
-
The thermostability, bioactive compounds and antioxidant activity of some vegetables subjected to different durations of boiling: investigation in vitro
PublikacjaThis research was performed in order to compare the water and acetone extracts of raw and boiled for 10, 20, 40 and 60 min Korean lotus roots (KLR) and Polish white onion (PWO) in the contents of theirbioactive compounds, antioxidant activity and thermostability.It was found that polyphenols (mg GAE/g), flavanols (mg GAE/g), flavonoids (mg CE/g), anthocyanins (mg CGE/kg) and tannins (mg CE/g) in water extract of raw lotus roots...
-
The termostability, bioactive compounds and antioxidant activity of some vegetables subjected to different durations of boiling: investigation in vitro.
PublikacjaThis research was performed in order to compare the water and acetone extracts of raw and boiled for 10, 20, 40 and 60 min Korean lotus roots (KLR) and Polish white onion (PWO) in the contents of theirbioactive compounds, antioxidant activity and thermostability. It was found that polyphenols (mg GAE/g), flavanols (mg GAE/g), flavonoids (mg CE/g), anthocyanins(mg CGE/kg) and tannins (mg CE/g) in water extract of raw lotus roots...
-
Heat transfer during pool boiling of water, methanol and R141b on porous coated horizontal tube bundles
PublikacjaPrzedstawiono wyniki badań eksperymentalnych wrzenia wody, metanolu i R141b na poziomym pęczku rur pokrytych metaliczna powłoką porowatą. Badania przeprowadzono dla podziałek rur 1.7d oaz 2d, przy ciśnieniu atmosferycznym i podciśnieniu.
-
Heat transfer and pressure drop during flow boiling of refrigerant/oil mixture inside smooth tube
PublikacjaW pracy przedstawiono wyniki badań współczynnika przejmowania ciepła i spadku ciśnienia podczas wrzenia czystych oraz zaolejonych czynników chłodniczych (R22, R134a, R407C) wrzących w poziomej stalowej rurce.
-
Experimental study of flow boiling pressure drop and heat transfer of R1233zd(E) at moderate and high saturation temperatures
PublikacjaThe paper presents the results of experimental study of flow boiling of R1233zd(E) in minichannel at moderate and high saturation temperatures. The heat transfer coefficient and pressure drop were measured for flow boiling in a stainless steel tube with 2 mm inside diameter and a length of 300 mm. Experiment has been conducted for saturation temperatures ranging from 83 to 145 °C which corresponds to values of reduced pressures...
-
Non-isothermal effects in a common method for calculation of heat transfer coefficient in flow boiling and flow condensation in minichannels
PublikacjaW pracy przestawiono efekty nieizotermiczne w metodzie wyznaczania współczynnika przejmowania ciepła podczas wrzenia w przepływie oraz kondensacji w przepływie w minikanałach. Wyniki obliczeń porównano z badaniami eksperymentalnymi z literatury, uzyskując dobrą zgodność.
-
Experimental investigation of M-shape heat transfer coefficient distribution of R123 flow boiling in small-diameter tubes
PublikacjaW publikacji przedstawiono wyniki badań wrzenia czynnika R123 w srebrnych rurkach o małych średnicach (średnice wewnętrzne wynosiły odpowiednio 1.15 mm i 2.3 mm). Badania przeprowadzono w szerokim zakresie stopnia suchości pary (0.01-0.9), gęstości strumienia masy (650-3000 kg/(m2s)) oraz gęstości strumienia ciepła (40-80 kW/m2). W badaniach wykazano, że istnieją dwa lokalne maksima współczynnika przejmowania ciepła w jego profilu...
-
A common method for calculation of flow boiling and flow condensation heat transfer coefficients in minichannels with account of nonadiabatic effects
PublikacjaW pracy przedstawiono metodę ogólną wyznaczania współczynników przejmowania ciepła podczas wrzenia w przepływie i kondensacji w przepływie w minikanałach z uwzględnieniem efektu nieadiabatycznego. Uwzględnia ona wpływ modyfikacji naprężeń stycznych na granicy ciecz-para na wymianę ciepła.
-
Improved semi-empirical method for determination of heat transfer coefficient in flow boiling in conventional and small diameter tubes
PublikacjaPraca dotyczy przedstawienia poprawionego modelu umożliwiającego wyznaczanie współczynnika przejmowania ciepła w kanałach o małych średnicach jaj i tych tradycyjnych. Model zweryfikowano na 6 czynnikach chłodnuiczych uzyskując bardzo zadowalającą zgodność.
-
Badania wrzenia R22 w rurkach z powłoką porowatą. Investigation of R22 flow boiling in porous tubes.
PublikacjaW pracy przedstawiono wyniki pomiarów współczynnika przejmowania ciepła przy wrzeniu w przepływie R22 w poziomej rurce z aluminiową powłoką porowatą. Otrzymane dane odniesiono do wyników uzyskanych dla gładkiej stalowej rurki oraz rurki typu microfin. Rurka gładka i z powłoką porowatą była wykonana ze stali nierdzewnej o grubości ścianki 0.6 mm. Grubość powłoki porowatej wynosiła 0,2 mm. Eksperymenty prowadzono przy stopniu suchości...
-
Measuring moisture damage of asphalt mixtures: The development of a new modified boiling test based on color image processing
Publikacja -
A semi-empirical method for calculation of flow boiling heat transfer coefficients for conventional channels and small diameter tubes
PublikacjaW pracy przedstawiono rozważania na temat modelowania dwufazowego przepływu wrzącego w kanałach konwencjonalnych i w kanałach o małej średnicy. Przedstawiono modyfikację korelacji zaproponowanej wcześniej przez J. Mikielewicza na podstawie nowych danych eksperymentalnych, uzyskanych dla kanałów o małej średnicy. Bank danych obejmował ponad 460 punktów pomiarowych dla czynników R141b, R134a, R113, R123, R12, R11 i wody. Uzyskano...
-
Heat transfer and pressure drop during flow boiling of pure efrigerants and refrigerant/oil mixtures in tube with porous coating
PublikacjaW pracy przedstawiono wpływ powłoki porowatej na średni współczynnik przejmowania ciepła oraz opory przepływu podczas wrzenia wybranych czynników chłodniczych wewnątrz poziomych rurek. Badania przeprowadzono dla techniczne czystych czynników chłodniczychR22, R134a i R407C oraz ich mieszanin z olejem poliestrowym 1% i 5% wrzących w rurkach wykonanych ze stali nierdzewnej, o wewnętrznej powierzchni gładkiej oraz z metaliczną powłoką...
-
Pool boiling heat transfer of water-Al2O3 and water-Cu nanofluids on horizontal stainless steel smooth and rough tubes
PublikacjaPrzedstawiono wyniki badań eksperymentalnych przejmowania ciepła przy wrzeniu nanocieczy woda-Al2O3 i woda-Cu na poziomych rurkach ze stali nierdzewnej. Ustalono, że niezależnie od badanej koncentracji nanocząstek (0.01%, 0.1% oraz 1%) współczynnik przejmowania ciepła dla nanocieczy był wyższy niż dla wody i rósł ze wzrostem koncentracji. Ponadto współczynnik przejmowania ciepła dla nanocieczy wzrastał ze wzrostem ciśnienia.
-
Evaluating Asphalt Mix Ingredients by Moisture Susceptibility: The Development of a New Modified Boiling Test Procedure Based on Digital Imaging
Publikacja -
Analytical model with non-adiabatic effects for pressure drop and heat transfer during boiling and condensation flows in conventional channels and minichannels
PublikacjaIn the paper a method developed earlier by authors is applied to calculations of pressure drop and heat transfer coefficient for boiling flow and condensation flow with account of non- adiabatic effects for some recent data collected from literature. The first effect, the modification of interface shear stresses in annular flow pattern is considered through incorporation of the so called "blowing parameter". The mechanism of...
-
Theoretical analysis and experimental tests of tilting pad journal bearings with shoes made of polymer material and low-boiling liquid lubrication
PublikacjaSelecting the appropriate bearing system for the rotor requires a good knowledge of the available solutions and the operating conditions of the machine. For newly designed machinery operating in adverse conditions, selecting bearings that ensure correct and long-lasting operation can be extremely challenging. Difficulties in- crease when the machine’s operating parameters are beyond the technical capabilities of available technical solutions....
-
The effect of pressure on heat transfer during pool boiling of water-Al2O3 and water-Cu nanofluids on stainless steel smooth tubes
PublikacjaPrzedstawiono wyniki badań eksperymentalnych wrzenia nanocieczy woda-Al2O3 i woda-Cu o koncentracjach nanocząstek 0.01%, 0.1% oraz 1% przy ciśnieniu absolutnym 10 kPa, 100 kPa oraz 200k Pa.
-
The effect of pressure on heat transfer during pool boiling of water-Al2O3 and water-Cu nanofluids on stainless steel smooth tube
PublikacjaPrzedstawiono wyniki badań eksperymentalnych wrzenia nanocieczy woda-Al2O3 i woda-Cu o koncentracjach nanocząstek 0.01%, 0.1% oraz 1% przy ciśnieniu absolutnym 10 kPa, 100 kPa oraz 200k Pa.
-
Measuring moisture damage of hot-mix asphalt (HMA) by digital imaging-assisted modified boiling test (ASTM D3625): Recent advancements and further investigation
Publikacja