Wyniki wyszukiwania dla: EACTIVE POWER FLOW OPTIMIZATION
-
On Alternative Approaches to Design of Corporate Feeds for Low-Sidelobe Microstrip Linear Arrays
PublikacjaTwo design approaches, illustrated by simulations and measurements, aiming at a systematic computer-aided design of printed circuit feeds for low-sidelobe microstrip antenna arrays are described. The novelty of these approaches resides in identification of the optimal feed architectures with subsequent simulation-based optimization of the feed and array aperture dimensions. In this work, we consider microstrip corporate feeds realizing...
-
Energy losses reduction in the medium voltage cable line – case study
PublikacjaThe paper presents an analysis of energy losses in a power cable system, which is composed of two 30 kV cable lines. This cable system is located at the seaside holiday area, so the load profile during a year is specific. Energy losses related to reactive power transmission, as well as to currents induced in the sheaths of the cables, are subject to analysis. Measurements were made in the system in order to prepare a computer model...
-
Współczynniki strat energetycznych w elementach napędu hydrostatycznego
PublikacjaW każdym układzie napędowym należy zastąpić obraz przepływu mocy opisany dotychczas powszechnie stosowanym wykresem Sankey’a spadku mocy zgodnego z kierunkiem przepływu mocy proponowanym przez autora wykresem wzrostu mocy w układzie przeciwnego do kierunku przepływu mocy. Należy więc opisywać straty i sprawność energetyczną a także pole pracy każdego silnika i układu napędowego jako zależne od wielkości fizycznych niezależnych...
-
STUDY ON THE EFFECTIVENESS OF THE TURBINE CONDENSER AIR EXTRACTION SYSTEM USING HYDRO EJECTORS
PublikacjaThe aim of the paper is to investigate the effectiveness of the 18K380 steam turbine condenser air extraction system using hydro ejectors. Motivation for the analysis is a need of improvement of the energy conversion ratio of the power plant. To achieve this goal it is necessary to establish efficiency of each subsystem of the energy cycle. The air extraction system is not a highly power consuming system but it has great impact...
-
Fault detection and diagnostics of complex dynamic systems using Gaussian Process Models - nuclear power plant case study
PublikacjaThe article examines the use of Gaussian Process Models to simulate the dynamic processes of a Pressurized Water nuclear Reactor for fault detection and diagnostics. The paper illustrates the potential of Gaussian Process Models as a tool for monitoring and predicting various fault conditions in Pressurized Water nuclear Reactor power plants, including reactor coolant flow and temperature variations, deviations from nominal working...
-
SELECTED COMBINED POWER SYSTEMS CONSISTED OF SELFIGNITION ENGINE AND STEAM TURBINE
PublikacjaThis paper presents optimization of selected combined diesel engine-steam turbine systems. Two systems: the system combined with waste heat one-pressure boiler only and its version containing additionally low-pressure boiler proper feeding degasifier and the system of two-pressure cycle, were taken into considerations. Their surplus values of power output and efficiency associated with utilization of waste heat contained in piston...
-
Energy efficiency of electric multiple units in suburban operation
PublikacjaThis thesis presents approach to analysis of energy efficiency of a suburban rail network, using novel models developed on the Matlab/Simulink basis. Necessary features and requirements for such models were determined thru in-depth review of the source literature in all applicable fields: electrified transportation systems, electric multiple units construction, vehicle drivetrains and finally, existing simulation methods. Existing...
-
Diesel electric a new trend on the ship propulsion
PublikacjaW artykule przedstawiono rozwój napędu "diesel elektrycznego" oraz argumentację zastosowania tego napędu na różnych typach statków. Referat zawiera również rozwiązania układu transmisji mocy oraz sprawność, jaka cechuje napęd elektryczny. W artykule zawarto również zalety tego napędu, oraz zwrócono uwagę na nowe koncepcje i rozwiązania korzystne dla wytwarzania i transmisji mocy w napędzie elektrycznym.This article presents development...
-
Power enhancement of the Brayton cycle by steam utilization
PublikacjaThe paper presents thermodynamic analysis of the gas-steam unit of the 65 MWe combined heat and power station. Numerical analyses of the station was performed for the nominal operation conditions determining the Brayton and combined cycle. Furthermore, steam utilization for the gas turbine propulsion in the Cheng cycle was analysed. In the considered modernization, steam generated in the heat recovery steam generator unit is directed...
-
Review of Methods for Diagnosing the Degradation Process in Power Units Cooperating with Renewable Energy Sources Using Artificial Intelligence
PublikacjaThis work is based on a literature review (191). It mainly refers to two diagnostic methods based on artificial intelligence. This review presents new possibilities for using genetic algorithms (GAs) for diagnostic purposes in power plants transitioning to cooperation with renewable energy sources (RESs). The genetic method is rarely used directly in the modeling of thermal-flow analysis. However, this assignment proves that the...
-
Design of synchronous generator two inputs regulator based on hinf control theory.
PublikacjaThe power system is highly nonlinear system, its dynamics depends on system network configuration, system loading… etc. To overcome the above mentioned difficulties and fulfill the performance requirements the different control methods are considered and tested for design of synchronous generator control system. Application of the H optimization method to synchronous generator regulator based on measurement of generator voltage...
-
Design analysis of Tesla micro-turbine operating on a low-boiling medium
PublikacjaThis paper presents results of the design analysis of a Tesla bladeless turbine intended for a co-generating micro-power plantof heat capacity 20 kW, which operates in an organic Rankine cycle on a low-boiling medium. Numerical calculations of flowin several Tesla turbine models were performed for a range of design parameters. Results of investigations exhibit interestingfeatures in the distribution of flow parameters within the...
-
A Concept of Modeling and Optimization of Applications in Large Scale Systems
PublikacjaThe chapter presents the idea that includes modeling and subsequent optimization of application execution on large scale parallel and distributed systems. The model considers performance, reliability and power consumption. It should allow easy modeling of various classes of applications while reflecting key parameters of both the applications and two classes of target systems: clusters and volunteer based systems. The chapter presents...
-
On the production of electricity in Poland using a geothermal binary power plant - A thermodynamic overview - Part I
PublikacjaPoland has a significant potential of geothermal energy. However, the high-temperature sources that are needed to drive power plants are found in relatively few places. Therefore, the objective of this paper is to consider any location in the northern part of Poland as a possible place to build a binary power plant. A scientific research was confirmed the existence of an elevated temperature gradient in this region. The hot rocks...
-
Optimal Rotating Receiver Angles Estimation for Multicoil Dynamic Wireless Power Transfer
PublikacjaThis study proposed an approach to dynamic wireless charging that uses a rotating receiver coil. Our simulation study focused on the verification of a novel way of increasing the coupling coefficient and power transfer stability by following the flux of the transmitting coils. To obtain the highest possible coupling by means of the FEM analysis, we studied the optimization of the trajectory of the angular velocity of the rotating...
-
Power converter interface for urban DC traction substations - solutions and functionality.
PublikacjaThis paper focuses on extending an urban DC traction substation functionality by means of an additional power converter interface (PCI). In particular, by enabling bidirectional energy exchange between LV DC traction grid, AC grid and V2G chargers. Among other things, the presented material compares general attributes of the most promising DC/DC converters that can be used in a PCI, meet the requirements of galvanic isolation and...
-
Design Analysis of Micro Gas Turbines in Closed Cycles
PublikacjaThe problems faced by designers of micro-turbines are connected with a very small volume flow rate of working media which leads to small blades’ height and high rotor speed. In the case of gas turbines this limitation can be overcome by the application of a closed cycle with very low pressure at the compressor inlet (lower than atmospheric pressure). In this way we may apply a micro gas turbine unit of accepted efficiency to work...
-
Experimental research on helical coil biomass boiler with oil as a heating fluid
PublikacjaThis paper presents an experimental research of helical coil biomass boiler with thermal oil heating agent. Heat exchanger consists of two coaxial helical coils swept by the flue gases. The burner is a single vertical retort connected to the fuel tank (wooden pellets). The boiler is a part of micro-power plant in which the heat from the boiler is exchanged with low-boiling HFE7100 to produce steam for a custom steam turbine. The...
-
TERMODYNAMIC CALCULATIONS OF TURBINE STEAM PARAMETERS
PublikacjaIn this work a heat balance was made for the nominal conditions of a block working with 18K370 turbine. For the parameters obtained, the thermal-flow calculations of the steam turbine were performed, maintaining the actual geometry of its flow system. Based on the nominal values obtained, iterative thermal and flow calculations were made for both the heat cycle of the power plant block and the steam turbine itself, seeking to obtain...
-
Exhaust gas temperature measurements in diagnostic examination of naval gas turbine engines. Part I: Steady-state processes
PublikacjaThe article presents a possible method of detecting failures in the flow section and supply system of a naval gas turbine engine based on the exhaust gas temperature measured behind the gas generator. This temperature is a basic diagnostic parameter use for evaluating the technical state of the turbine engine in operation, and is monitored during engine start-ups, accelerations and decelerations of rotor units, and steady-load...
-
Effect of asymmetric fluid flow distribution on flow boiling in a microchannel heat sink – An experimental investigation
PublikacjaFlow boiling in microchannels is emerging as an exclusive cooling solution for miniaturized high-power electronic devices alongside having other high heat flux applications. Size miniaturization at microscale strangely increases heat transfer performance as well as flow boiling instabilities. Many flow boiling instabilities are interrelated and result from imperfect hydrodynamic conditions. One of such problems is flow maldistribution among...
-
Possibilities of the performance improvement of the aero- and marine propulsion units equipped with combustion piston engines
PublikacjaWithin the paper there have been presented the authors' opinions concerning possibilities and needs of the performance optimization of the aero- and marine units powered by piston engines both of ''classic'' and contemporary construction. There have been also discussed the reserves contained within combustion piston engines which enable its performance improvement (the power and specific fuel consumption) as well as the fulfillment...
-
Comparative Analysis of Reactive Power Compensation Devices in a Real Electric Substation
PublikacjaA constant worldwide growing load stress over a power system compelled the practice of a reactive power injection to ensure an efficient power network. For this purpose, multiple technologies exist in the knowledge market out of which this paper emphasizes the usage of the flexible alternating current transmission system (FACTS) and presents a comparative study of the static var compensator (SVC) with the static synchronous compensator...
-
New Performance Indices for Power System Stabilizers
PublikacjaThe subject of the article is issues related to innovative indices for power system stabilizers (PSSs). These new indices will be able to quickly show which PSS (among many other PSSs) is not working properly and that advanced optimization and simulation methods should be used to improve the PSS settings. The authors note the fact that the acceptance requirements for PSSs are different in various power systems. Moreover, the authors...
-
Modeling and Simulation for Exploring Power/Time Trade-off of Parallel Deep Neural Network Training
PublikacjaIn the paper we tackle bi-objective execution time and power consumption optimization problem concerning execution of parallel applications. We propose using a discrete-event simulation environment for exploring this power/time trade-off in the form of a Pareto front. The solution is verified by a case study based on a real deep neural network training application for automatic speech recognition. A simulation lasting over 2 hours...
-
Możliwości ograniczenia zużycia energii napędowej urządzeń przez optymalizację doboru wymienników ciepła, właściwą konfigurację i kontrolę przepływu płynów roboczych
PublikacjaArtykuł poświęcony możliwości ograniczenia zużycia energii napędowej urządzeń na drodze optymalizacji doboru wymienników ciepła, właściwej konfiguracji i kontroli przepływu płynów roboczych. Przedstawiono w nim ocenę zużycia energii w systemach energetycznych o największej energochłonności w realiach Polski. Zwrócono uwagę na możliwość wykorzystania wymienników ciepła o wysokiej efektywności dla zmniejszenia oporu przenoszenia...
-
Partial Admission Stages of High Efficiency for a Microturbine
PublikacjaThe paper presents the results of a design analysis of a microturbine for a cogeneration micro-power plant working in accordance with organic Rankine cycle. The heat power of the plant is assumed equal to 20kW and the corresponding available electric output is estimated to be about 3 kW. After the design analysis, the axial turbine with partial admission in all stages was built and tested experimentally. Special attentionwas paid...
-
Partial Admission Stages of High Efficiency for a Microturbine
PublikacjaThe paper presents the results of a design analysis of a micro-turbine for a co-generation micro-power plant working in accordance with organic Rankine cycle. The heat power of the plant is assumed equal to 20kW and the corresponding available electric output is estimated to be about 3kW. After the design analysis, the axial turbine with partial admission in all stages was built and tested experimentally. Special attention was...
-
An experimental investigation on the effect of new continuous core-baffle geometry on the mixed convection heat transfer in shell and coil heat exchanger
PublikacjaIn the article, the authors presented the influence of continuous core-baffle geometry at mixed convection heat transfer in shell and coil heat exchanger. Experiments were carried out for a large power range, i.e. from 100W to 1200W and mass flow rates ranging from 0.01 kg/s to 0.025 kg/s. During the experiments, the mass flow rate of cooling water, the temperature of water at the inlet and outlet as well as the wall temperature...
-
OPTIMIZATION OF THE LAST STAGE OF GAS-STEAM TURBINE USING A HYBRID METHOD
PublikacjaThis paper relates to the CFD calculation of a new turbine type which is in the phase of theoretical analysis, because the working fluid is a mixture of steam and gas generated in wet combustion chamber. At first, this article concentrates on a possibility of streamlining the flow efficiency of a last stage of axial turbine working on gas-steam mixture using a hybrid of the particle swarm optimization algorithm with the Nelder-Mead...
-
Particle Image Velocimetry Measurements of Airflow in Electrohydrodynamic Device for Dust Particle Collection
PublikacjaIn this paper the electrohydrodynamic (EHD)device for gas pumping and cleaning is presented. To induce an airflow in this EHD device corona discharge was used. The discharge was generated between the one-sided spike electrodes and the plate electrodes. An asymmetric electric field and generated discharge result in unidirectional gas flow through the EHD device. The current-voltage characteristics were measured and the corona discharge...
-
Compact broadband multi-way 1:6 power divider
PublikacjaThis paper introduces a design flow of a microstrip multi-way 1:6 power divider incorporating photonic bandgap (PBG) structures. Themethod proposed has enabled the achievement of considerable miniaturization (15%) together with transmission characteristics enhancement(141% bandwidth). Measured results show significant similarity to theoretical characteristics, which proves the attractiveness of presented design methodology.
-
Management of low-temperature heat source by ORC aided by additional heat source
PublikacjaIn the paper presented is a concept to utilize waste heat from the power plant with the aid of the low-temperature ORC cycle. The ORC system is heated from two heat sources, the first one being the flow rate of waste heat obtained from the exhaust gases. Subsequently, the working fluid in the cycle is additionally heated by the condensing steam from the low pressure turbine extraction points increasing in such way the level of...
-
Power augmentation of PGE Gorzow's gas turbine by steam injection - thermodynamic overview
PublikacjaThe impact of steam injection upon a gas turbine and a combined power plant performance has been investigated. This article describes and summarizes possibilities of modification for current gas turbine in PGE Gorzow power plant into the Cheng cycle. Our modification deals with a thermal cycle, in which steam produced in a heat recovery steam generator is injected into the gas turbine's combustion chamber. It has been proved that...
-
MARKAL long-term power generation scenarios for Poland - Concept of the model
PublikacjaIn this paper we have presented the concept of Polish MARKAL optimization model developed for the needs of power generation scenarios in long-term perspective i.e. by 2040. The depiction of Polish MARKAL with Reference Energy System structure was provided. In addition, basic model assumptions, energy technology database, projections of electricity demand and power plant ageing pathways were presented. Our goal is to test MARKAL...
-
Low-cost multiband compact branch-line coupler design using response features and automated EM model fidelity adjustment
PublikacjaDesign closure of compact microwave components is a challenging problem because of significant electromagnetic (EM) cross-couplings in densely arranged layouts. A separate issue is a large number of designable parameters resulting from replacement of conventional transmission line sections by compact microstrip resonant cells. This increases complexity of the design optimization problem and requires employment of expensive high-fidelity...
-
Cascaded Buck Hybrid Interlink Converter for Multiple-Input / Multiple-Output Operation
PublikacjaThe provision of isolated- and non-isolated DC output voltages by Power electronics power-conditioning devices in the recent ‘green-energy-revolution’ era is on course. In this paper, a structure for multi-input multi-output(MIMO) DC–DC buck converter is proposed to generate output voltages of varying levels with fewer component-count. The DC output voltage of each of the constituting buck converters can be used independently or...
-
The excitation controller with gain scheduling mechanism for synchronous generator control
PublikacjaThe power systems, including the synchronous generators and power systems networks, are complex nonlinear systems with configuration and parameters which change through time. That leads to electromechanical oscillations occurring in that system. Thus synchronous generator excitation controller must be capable of providing appropriate stabilization signal over broad range of operating conditions and disturbances. In this paper,...
-
Expedited Optimization of Passive Microwave Devices Using Gradient Search and Principal Directions
PublikacjaOver the recent years, utilization of numerical optimization techniques has become ubiquitous in the design of high-frequency systems, including microwave passive components. The primary reason is that the circuits become increasingly complex to meet ever growing performance demands concerning their electrical performance, additional functionalities, as well as miniaturization. Nonetheless, as reliable evaluation of microwave device...
-
Exhaust gas temperature measurements in diagnostic examination of naval gas turbine engines. Part II. Unsteady processes
PublikacjaThe second part of the article presents the results of operating diagnostic tests of a two- and three-shaft engine with a separate power turbine during the start-up and acceleration of the rotor units. Attention was paid to key importance of the correctness of operation of the automatic engine load control system, the input for which, among other signals, is the rate of increase of the exhaust gas flow temperature. The article...
-
Explicit Size-Reduction-Oriented Design of a Compact Microstrip Rat-Race Coupler Using Surrogate-Based Optimization Methods
PublikacjaIn this paper, an explicit size reduction of a compact rat-race coupler implemented in a microstrip technology is considered. The coupler circuit features a simple topology with a densely arranged layout that exploits a combination of high- and low-impedance transmission line sections. All relevant dimensions of the structure are simultaneously optimized in order to explicitly reduce the coupler size while maintaining equal power...
-
Zygfryd Domachowski prof. dr hab. inż.
Osoby -
High Frequency Harmonics Emission of Modern Power Electronic AC-DC Converters
PublikacjaModern AC/DC converters with bidirectional power flow employing PWM boost topology generate harmonic distortions of input current in relatively high frequency range tightly related to modulation carrier frequency. These frequencies and its multiples in typical applications are usually located in frequency range from single up to several of kHz. Increased harmonic emission in this frequency range can easily and harmfully influence...
-
Analysis of the Impact of Charging Electric Cars on the Power System Load
PublikacjaThe paper presents ways of integrating electric cars with the power system. In connection with this, daily load curves in the average working day have been developed in the G2V (Grid-to-Vehicle) and V2G (Vehicle-to-Grid) variants. The G2V solution consists in unidirectional energy flow from the power system to a vehicle’s battery. The V2G solution consists in bi-directional energy exchange between the power system and electric...
-
Impact of thermal backfill parameters on current-carrying capacity of power cables installed in the ground
PublikacjaProper design of power installations with the participation of power cables buried in homogeneous and thermally well-conductive ground does not constitute a major problem. The situation changes when the ground is non-homogeneous and thermally low-conductive. In such a situation, a thermal backfill near the cables is commonly used. The optimization of thermal backfill parameters to achieve the highest possible current-carrying capacity...
-
Optimization of using recuperative braking energy on a double-track railway line
PublikacjaIn the introduction, possible ways of reusing energy from recuperation are presented. Next, the paper investigates the possibility of using regenerative braking in the range allowed by the detailed timetable by adopting the method of transferring the recovered electric energy directly to the catenary and immediate use of this energy by another train at the same power section. In the main part of the work, it is shown, that the...
-
Increase of power and efficiency of the 900 MW supercritical power plant through incorporation of the ORC
PublikacjaThe objective of the paper is to analyse thermodynamical and operational parameters of the supercritical power plant with reference conditions as well as following the introduction of the hybrid system incorporating ORC. In ORC the upper heat source is a stream of hot water from the system of heat recovery having temperature of 90 °C, which is additionally aided by heat from the bleeds of the steam turbine. Thermodynamical analysis...
-
Preliminary design of the last stage of supercritical steam turbine and proposition of anti-erosion coating for blades surface
PublikacjaIn this article a preliminary design of the last stage of supercritical steam turbine has been presented. A computational model of supercritical thermal cycle has been created in order to determine steam parameters at the stage inlet and outlet. The model was based on the structure of German coal-fired power plant Datteln 4. Further steam-flow parame-ters and dimensions of stator and rotor blades have been calculated analytically....
-
Particle Swarm Optimization Based Optimal Design of Six-Phase Induction Motor for Electric Propulsion of Submarines
PublikacjaAbstract: Recent research reveals that multi-phase motors in electric propulsion systems are highly recommended due to their improved reliability and efficiency over traditional three phase motors. This research presented a comparison of optimal model design of a six phase squirrel cage induction motor (IM) for electric propulsion by using Genetic Algorithm (GA) and Particle Swarm Optimization (PSO). A six phase squirrel cage induction...
-
Minimizing Greenhouse Gas Emissions From Ships Using a Pareto Multi-Objective Optimization Approach
PublikacjaTo confront climate change, decarbonization strategies must change the global economy. According to statements made as part of the European Green Deal, maritime transport should also become drastically less polluting. As a result, the price of transport must reflect the impact it has on the environment and on health. In such a framework, the purpose of this paper is to suggest a novel method for minimizing emissions...