Wyszukiwarka
Wyniki wyszukiwania dla: GAS TURBINES
-
Design Analysis of Micro Gas Turbines in Closed Cycles
PublikacjaThe problems faced by designers of micro-turbines are connected with a very small volume flow rate of working media which leads to small blades’ height and high rotor speed. In the case of gas turbines this limitation can be overcome by the application of a closed cycle with very low pressure at the compressor inlet (lower than atmospheric pressure). In this way we may apply a micro gas turbine unit of accepted efficiency to work...
-
Gas turbines – technological development and potential use in CAES systems
PublikacjaThis article briefly describes Compressed Air Energy Storage (CAES), focusing on the technological development of one of the key elements of such systems – the gas turbines. It presents the basic parameters and features of gas turbines, as well as turbine classes with example models. Main tendencies in the structural and technological development are discussed. Changes and trends on electric energy markets are becoming more and...
-
JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME
Czasopisma -
Fundamentals of Steam and Gas Turbines OASIV
Kursy OnlineApplication of turbines in industry and sea power plants. Basic thermodynamics and fluid flow mechanics in turbomachinery. Steam turbine power cycle and plants. Gas turbine power cycle and plants. Turbine blading systems operation.
-
Steam and Gas Turbines Constuction_ seminar/project
Kursy Online -
Specificity of automatic control of micro-turbines (steam or gas -driven and expanders) in dispersed generation system of heat and electric power
PublikacjaThis paper presents specific problems of automatic control of steam micro-turbines and expanders intended for the dispersed, combined generating of heat and electric power. The investigations concern ensurance of certainty of energy supply and its required quality.
-
An impact of ambient parameters change on steam and gas turboset control. The International Conference on ''Turbines of Large Output'' devoted to 100th Anniversary of prof. Robert Szewalski Birthday.
PublikacjaPorównano wpływ zmian parametrów otoczenia (ciśnienia i temperatury) na charakterystyki turbiny parowej i gazowej. Na tej podstawie zbadano wpływ tych parametrów na charakterystyki układu kombinowanego parowo-gazowego. Przedstawiono, w związku z tym, koncepcję kompensatora wpływu zmian parametrów otoczenia na charakterystyki układu kombinowanego parowo-gazowego.
-
Marek Dzida dr hab. inż.
OsobyUrodził się 6 sierpnia 1953 r. w Bielsku-Białej. Absolwent Instytutu Okrętowego Politechniki Gdańskiej, od 1978 r. pracuje na Wydziale Oceanotechniki i Okrętownictwa PG. W 1983 r. uzyskał tytuł doktora nauk technicznych, w 2001 r. – doktora habilitowanego. Aktualnie zatrudniony na stanowisku profesora nadzwyczajnego na PG. Pełnił funkcję prodziekana ds. kształcenia WOiO (1996–2002) oraz dziekana (2005–2012). Od 2010 r. jest kierownikiem...
-
Isothermal turbines − New challenges. Numerical and experimental investigations into isothermal expansion in turbine power plants
PublikacjaThe efficiency of power plants with steam or gas turbines depends on the efficiencies of a thermodynamic cycle and devices implementing this cycle. In the case of high power outputs, we cannot expect a significant increase in the efficiency of individual devices. Therefore, what remains is to increase the efficiency of the implemented thermodynamic cycle - the complex Rankine cycle in the case of steam turbines or the extended...
-
Analysis of operations of combined STIG installation
PublikacjaSteam injection in gas turbines is interesting technology with good energetic and ecological properties of gas turbines. In these applications the heat of exhaust gases is used to produce steam, which is injected in the combustion chamber of a gas turbine. The steam injection increase the power and efficiency of the installation. there are some possibilities to increases the properties of STIG turbines, for example by meas of additional...
-
APPLICABILITY OF INLET AIR FOGGING TO MARINE GAS TURBINE
PublikacjaThe dependency of marine gas turbine on the ambient temperature leads to a decrease of the gas turbine power output in arid areas. Very often gas turbine power output demand is high and the power margins originally designed into the driver , has been exhausted. In such circumstances the inlet air fogging is an effective compensation of gas turbine power. In this paper an analysis of inlet air fogging applicability to marine gas...
-
Inlet air fogging of marine gas turbine in power output loss compensation
PublikacjaThe use of inlet air fogging installation to boost the power for gas turbine engines is widely applied in the power generation sector. The application of fogging to mechanical drive is rarely considered in the literature [1]. This paper will cover some considerations relating to its application to gas turbines in ship drive. There is an important evaporative cooling potential throughout the world when the dynamic data is evaluated,...
-
Compact High Efficiency and Zero-Emission Gas-Fired Power Plant with Oxy-Combustion and Carbon Capture
PublikacjaReduction of greenhouse gases emissions is a key challenge for the power generation industry, requiring the implementation of new designs and methods of electricity generation. This article presents a design solution for a novel thermodynamic cycle with two new devices—namely, a wet combustion chamber and a spray-ejector condenser. In the proposed cycle, high temperature occurs in the combustion chamber because of fuel combustion...
-
A comparative study of pentanol (C5 alcohol) and kerosene blends in terms of gas turbine engine performance and exhaust gas emission
PublikacjaThe growing demand for sustainable and clean energy sources provides the incentive for the development of alternative fuels. Simultaneously, the development of gas turbine technologies with flexible fuel supply systems enables the use of alternative non-fossil fuels that can play key roles in contributing to global efforts in meeting emissions targets. This paper presents the current state of knowledge on the production and potential...
-
Thermal failure of a second rotor stage in heavy duty gas turbine
PublikacjaThe impulse mode of operation and the supply of various types of fuels causes frequent failures even in the heavy duty gas turbines. The paper presents the ravages of second rotor stage failure in a gas turbine. The excessive thermal elongation rise caused by fuel change was indicated as the main cause. We applied nonlinear numerical analysis, preceded by thermodynamic calculations of the turbine and visual inspection of the effects...
-
Gas Turbine Cycle with External Combustion Chamber for Prosumer and Distributed Energy Systems
PublikacjaThe use of various biofuels, usually of relatively small Lower Heating Value (LHV), affects the gas turbine efficiency. The present paper shows that applying the proposed air by-pass system of the combustor at the turbine exit causes tan increase of efficiency of the turbine cycle increased by a few points. This solution appears very promising also in combined gas/steam turbine power plants. The comparison of a turbine set operating...
-
Turbomachinery - Background
PublikacjaThe "Turbomachinery - Background" is the first part of a series of monographs devoted to different aspects of rotating machines. The book presents the main fundamentals which are necessary for the different problems of steam, gas, wind and water turbines as well as pumps, compressors and propellers which will discussed in detail in the subsequent parts of the series.
-
An Impact of Environmental Disturbances on Combined Cycle Power Plant Control
PublikacjaCombined cycle power plants operate at thermal efficiency approaching 60 percent. In the same time their performance presents several problems that have to be addressed. E.g. gas turbines are very sensitive to backpressure exerted on them by the heat recovery steam generators as well as to ambient pressure and temperature.
-
Wybrane zagadnienia przepływowe turbiny gazowej pracującej w tłoczni gazu ziemnego.
PublikacjaW niniejszym artykule przedstawiono cieplno-przepływowe obliczenia turbiny gazowej, stanowiącej napęd sprężarki w tłoczni gazu ziemnego. Wartości parametrów wejściowych niezbędnych do przeprowadzenia obliczeń przyjęto na podstawie danych technicznych tłoczni zasilających polski odcinek gazociągu tranzytowego Jamał-Europa, w których pracują turbiny gazowe SGT-600 firmy Siemens, o mocy 25,3 MW.
-
A study of a compact high-efficiency zero-emission power plant with oxy-fuel combustion
PublikacjaThis paper discusses the application of global trends in gas cycles technology using oxy-fuel combustion. This is followed by a demonstration of a design solution for a new cycle with two enhanced energy-converting devices, namely a wet combustion chamber and a spray-ejector condenser. The proposed gas and steam cycle unit is contained within a single turbine, whose benefits combine those offered by gas turbines (high inlet temperatures)...
-
Technical and Economic Analysis of the Supercritical Combined Gas-Steam Cycle
PublikacjaCombined cycle power plants are characterized by high efficiency, now exceeding 60%. The record-breaking power plant listed in the Guinness Book of World Records is the Nishi-Nagoya power plant commissioned in March 2018, located in Japan, and reaching the gross efficiency of 63.08%. Research and development centers, energy companies, and scientific institutions are taking various actions to increase this efficiency. Both the gas...
-
Heat Turbomachinery
Kursy Online1. Steam turbine cycles. 2. Gas turbine cycles. 3. Combined gas-steam cycles. 4. Flows in nozzles. 5. Theory of turbine stages. 6. Multistage turbines. 7. Examples of turbine design.
-
CFD analysis of fluid flow through the labyrinth seal
PublikacjaSteam and gas turbines are some of the fundamental means of power generation. The energy efficiency of the turbines, however, is not satisfactory. Ever since the start-up of the first turbine in the world, engineers have been striving for their increased efficiency. Multiple solutions to the problem of steam loss in an operating turbine are available. The use of seals is one of them. Empirical methods or numerical calculations...
-
High-efficient, zero-emission energy production
PublikacjaThis paper presents innovative thermodynamiccycles with high-efficient, zero-emission energy production. The main aim of this work is to show the role of nano-phenomena in the enhancement of the power of thermodynamic cycles. For that purpose, the cycles using oxy-combustion and spray ejected condensation are first studied and, secondly hybrid cycles using fuel cells and gas turbines are presented. The role of nano-phenomena in...
-
Heat turbomachinery
Kursy Online1. Steam turbine cycles. 2. Gas turbine cycles. 3. Combined gas-steam cycles. 4. Flows in nozzles. 5. Theory of turbine stages. 6. Multistage turbines. 7. Examples of turbine design.
-
Thermodynamic Cycle Concepts for High-Efficiency Power Plants. Part B: Prosumer and Distributed Power Industry
PublikacjaAn analysis was carried out for different thermodynamic cycles of power plants with air turbines. A new modification of a gas turbine cycle with the combustion chamber at the turbine outlet has been described in the paper. A special air by-pass system of the combustor was applied, and in this way, the efficiency of the turbine cycle was increased by a few points. The proposed cycle equipped with an effective heat exchanger could...
-
ENERGY STORAGE IN COMPRESSED AIR – SOLUTION SUPPORTING RENEWABLE ENERGY SOURCES
PublikacjaThis article presents a brief description of a power system, the current national power system daily load, the use of wind power as a renewable energy source and its share in the national load. It also discusses the methods for storing energy, their characteristics and possible solutions. The power storage and generation solution proposed in the article is based on the collaboration between a gas turbine and an air storage system....
-
Thermodynamic Cycle Concepts for High-Efficiency Power Plans. Part A: Public Power Plants 60+
PublikacjaAn analysis was carried out for different thermodynamic cycles of power plants with air turbines. Variants with regeneration and different cogeneration systems were considered. In the paper, we propose a new modification of a gas turbine cycle with the combustion chamber at the turbine outlet. A special air by-pass system of the combustor was applied and, in this way, the efficiency of the turbine cycle was increased by a few points....
-
Subcritical Thermodynamic Cycles with Organic Medium and Isothermal Expansion
PublikacjaThe efffciencies of the Organic Rankine Cycle (ORC) are not very high and only very seldom do they exceed 20%. The increase and optimization of initial parameters and certain modifications of the thermodynamic cycle make it possible to overcome these drawbacks. A new modified cycle has been described and analyzed in detail in the paper. Similarly to the Ericsson cycle for gas turbines, isothermal expansion in the turbine is suggested...
-
Thermodynamic Cycles of Air Microturbine Power Plants Working on Biomass Fuels
PublikacjaThe gas turbine engine is modified to work as an air turbine set which consists, in the simplest arrangement, of a compressor, a heat exchanger and a turbine. Air is a working medium for both: the compressor and the turbine. This kind of air turbine set can be applied in power plants working on biomass fuels. In this solution we can burn fuels of varying parameters in the external combustion chamber without any harmful effects...
-
Organic Supercritical Thermodynamic Cycles with Isothermal Turbine
PublikacjaOrganic Rankine cycles (ORC) are quite popular, but the overall efficiencies of these plants are rather very low. Numerous studies have been conducted in many scientific centers and research centers to improve the efficiency of such cycles. The research concerns both the modification of the cycle and the increase in the parameters of the medium at the inlet to the turbine. However, the efficiency of even these modified cycles rarely...
-
Conditions for increasing the recognition of degradation in thermal-flow diagnostics, taking into account environmental legal aspects
PublikacjaThe ever-increasing demand for electricity and the need for conventional sources to cooperate with renewable ones generates the need to increase the efficiency and safety of the generation sources. Therefore, it is necessary to find a way to operate existing facilities more efficiently with full detection of emerging faults. These are the requirements of Polish, European and International law, which demands that energy facilities...
-
Influence of Holes Manufacture Technology on Perforated Plate Aerodynamics
PublikacjaTranspiration flow is a very important and still open subject in many technical applications. Perforated walls are useful for the purpose of “flow control”, as well as for the cooling of walls and blades (effusive cooling) in gas turbines. We are still not able to include large numbers of holes in the numerical calculations and therefore we need physical models. Problems are related also to the quality of the holes in perforated...
-
Thermodynamic analysis of the Compressed Air Energy Storage system coupled with the Underground Thermal Energy Storage
PublikacjaImprovement of flexibility is one of the key challenges for the transformation of the Polish Power System aiming at a high share of renewable energy in electricity generation. Flexible and dispatchable power plants will contribute to this ongoing transformation process as they compensate for fluctuations in electricity generation from renewable energy sources such as wind and photovoltaics. In this context, CAES storage tanks are...
-
Review of Methods for Diagnosing the Degradation Process in Power Units Cooperating with Renewable Energy Sources Using Artificial Intelligence
PublikacjaThis work is based on a literature review (191). It mainly refers to two diagnostic methods based on artificial intelligence. This review presents new possibilities for using genetic algorithms (GAs) for diagnostic purposes in power plants transitioning to cooperation with renewable energy sources (RESs). The genetic method is rarely used directly in the modeling of thermal-flow analysis. However, this assignment proves that the...
-
Innovative Turbine Intake Air Cooling Systems and Their Rational Designing
PublikacjaThe improved methodology of the engine intake air cooling system designing based on the annual effect due to cooling was developed. It involves determining the optimal value of cooling capacity, providing the minimum system sizes at maximum rate of annual effect increment, and its rational value, providing a close to maximum annual effect without system oversizing at the second maximum rate of annual effect increment within the...
-
Systems Engineering Requirements for Rotating Machines (PG-00060237)
Kursy OnlineTurbiny wiatrowe, gazowe, mikroturbiny, silniki lotnicze, turbosprężarki i inne systemy mechaniczne to przykłady maszyn wirujących, które wymagają wysoko wykwalifikowanych inżynierów. Powinni oni zrozumieć złożoność procesów projektowania i produkcji, w tym wytwarzania przyrostowego, oraz konserwacji prognostycznej opartej na inżynierii cyfrowej dla bezawaryjnej pracy silnika. Wind, gas, micro turbines, aircraft engines, turbochargers,...
-
Design of horizontal axis wind and water turbines
PublikacjaThe basic hydrodynamic principles of horizontal axis turbines are presented. Computational methods based on vortex theory for design of such turbines and for calculation of their hydro or aerodynamic characteristics are described in detail. These methods are applicable both to wind and water turbines. The influence of detailed turbine geometry on its characteristics is presented. Several practical computational examples of different...
-
Experimental ORC micro-power plant for CHP application Part B: Radial and Multi-stage axial turbines
PublikacjaThe co-generative micro-power plant with the HFE7100 applied as a working medium was designed and built for experimental investigations. Special attention is paid to a micro-turbine which was built and tested in two variants: a radial turbine and an axial turbine. A concept of a radial turbine with 2 centripetal and 2 centrifugal stages is shown. This prototype was equipped with an aerostatic gas bearing and, alternatively, with...
-
SOME PROBLEMS OF SUPPORTING OFFSHORE WIND TURBINES
PublikacjaBasic problems of foundations of sea wind turbines are considered in this paper. This aims to search for solutions to optimize supporting of the offshore turbines with a size greater than 10 MW. The types of foundations, their basic features, including most important dimensions, applications as well as general design considerations are discussed. Numerical model of the offshore turbine and some preliminary computations for a case...
-
Analysis of Failures of High Speed Shaft Bearing System in a Wind Turbine
PublikacjaDuring the operation of wind turbines with gearbox of traditional configuration, consisting of one planetary stage and two helical stages high failure rate of high speed shaft bearings is observed. Such a high failures frequency is not reflected in the results of standard calculations of bearing durability. Most probably it can be attributed to atypical failure mechanism. The authors studied problems in 1.5 MW wind turbines of...
-
The Finite Elements Method application to assesment the impact of turbulence generated by wind turbines on their lacation inclose proximity of overhead high voltage power transmissionlines
PublikacjaThe paper presents selected aspects of construction of wind turbines location concerning aerodynamic impact on power lines. Reaserch is based on the source data concerning the aerodynamic impact of a wind farm consisting of 8 turbines and 400 kV power line, an analysis of the possibility of wind farm locating in the immediate vicinity of the line was carried out. There are serious problems with locating higher capacity wind farms...
-
Recovering Sound Produced by Wind Turbine Structures Employing Video Motion Magnification
PublikacjaThe recordings were made with a fast video camera and with a microphone. Using fast cameras allowed for observation of the micro vibrations of the object structure. Motion-magnified video recordings of wind turbines on a wind farm were made for the purpose of building a damage prediction system. An idea was to use video to recover sound & vibrations in order to obtain a contactless diagnostic method for wind turbines. The recovered signals...
-
Wymagania inżynierii systemów dla maszyn wirujących (PG-00060237)
Kursy OnlineTurbiny wiatrowe, gazowe, mikroturbiny, silniki lotnicze, turbosprężarki i inne systemy mechaniczne to przykłady maszyn wirujących, które wymagają wysoko wykwalifikowanych inżynierów. Powinni oni zrozumieć złożoność procesów projektowania i produkcji, w tym wytwarzania przyrostowego, oraz konserwacji prognostycznej opartej na inżynierii cyfrowej dla bezawaryjnej pracy silnika. Kurs zapewnia fundamentalną wiedzę wymaganą w przemyśle...
-
Analyzing Wind Energy Potential Using Efficient Global Optimization: A Case Study for the City Gdańsk in Poland
PublikacjaWind energy (WE), which is one of the renewable energy (RE) sources for generating electricity, has been making a significant contribution to obtaining clean and green energy in recent years. Fitting an appropriate statistical distribution to the wind speed (WS) data is crucial in analyzing and estimating WE potential. Once the best suitable statistical distribution for WS data is determined, WE potential and potential yield could...
-
Research of Emergency Modes of Wind Power Plants Using Computer Simulation
PublikacjaThe aim of this study is to investigate changes in the wind power plant energy production parameters under the conditions of sudden wind changes and voltage drop. To achieve these goals, a simulation of operation of wind power plants was performed. Twelve wind turbines with variable rotational speed equipped with a Fuhrländer FL 2500/104 asynchronous double-fed induction generator (DFIG) were used, each with an installed capacity...
-
Accuracy Investigations of Turbine Blading Neural Models Applied to Thermal and Flow Diagnostics
PublikacjaPossibility of replacing computional fluid dynamics simulations by a neural model for fluid flow and thermal diagnostics of steam turbines is investigated. Results of calculations of velocity magnitude of steam for 3D model of the stator of steam turbine is presented.
-
Manufacturing and Recycling Impact on Environmental Life Cycle Assessment of Innovative Wind Power Plant Part 1/2
PublikacjaWind power plants are considered as ecologically-clean source of energy. However, manufacturing processes cannot be treated that way. Manufacturing processes consume huge amount of electrical and thermal energy and significant amount of materials, e.g. steel, polymers, oils and lubricants. All of the above could be potentially harmful for environment. There are not many works and publications regarding life-cycle analysis of wind...
-
SHORT REVIEW AND 3-D FEM ANALYSIS OF BASIC TYPES OF FOUNDATION FOR OFFSHORE WIND TURBINES
PublikacjaSome problems of the foundations of offshore wind turbines are considered in this paper. A short review is presented on the two basic types of foundations, i.e. monopiles and gravity foundations, including their basic features and applications as well as general design considerations. Also, some issues regarding analysis are discussed, including geotechnical problems and modelling techniques. A numerical model of offshores turbine...
-
Comparative analysis of the theoretical models of ideal propulsor, ideal fluid brake, ideal screw propeller and ideal axial wind turbine
PublikacjaThe article presents a detailed discussion of four different fluid dynamics devices.These devices are presented with all relevant mathematical formulae regarding the forces, the power and the efficiency. It is demonstrated that application of the Betz theorem to axial wind turbines is not correct and it underestimates the maximujm achievable efficiency. This conclusion is supported by numerical calculations.