Wyniki wyszukiwania dla: stainless steel
-
Sessile droplet contact angle of water–Al2O3, water–TiO2 and water–Cu nanofluids
PublikacjaThis work presents measurements of the contact angle of sessile droplets for three nanofluids, i.e. water–Al2O3, water–TiO2 and water–Cu. The plates made of glass, anodized aluminium and stainless steel of different roughness served as substrates. Ultrasonic vibration was used for 30–60 min in order to stabilise the dispersion of the nanoparticles. Nanoparticles were tested at the concentration of 0.01%, 0.1%, and 1% by weight....
-
Electrohydrodynamic flow patterns and collection efficiency in narrow wire-cylinder type electrostatic precipitator
PublikacjaRecently, narrow electrostatic precipitators (ESPs) have become a subject of interest because of their possible application for the cleaning of the exhaust gases emitted by diesel engines. Diesel engines emit fine particles, which are harmful to human and animal health. There are several methods for decrease particulate emission from a diesel engines, but up to now, these methods are not enough effective or very expensive. Therefore,...
-
Electrolytic deposition of reactive element thin films on Crofer 22 APU and evaluation of the resulting high-temperature corrosion protection properties at 700 °C–900 °C
PublikacjaThis article presents electrolytic deposition of thin Rare Earth (RE) coatings on Crofer 22 APU stainless steel substrates for high temperature applications, such as interconnects in solid oxide cell stacks. The deposition of coatings based on yttrium-, gadolinium-, lanthanum-, and cerium nitrates is discussed. The high temperature corrosion properties of surface-modified steels were examined using thermogravimetry and electrical...
-
A COMPARISON OF WEAR PROPERTIES OF WATER LUBRICATED NBR AND PTFE SLIDING BEARINGS
PublikacjaThe excessive wear of a journal shaft can be caused by many factors, for example, working conditions (e.g., temperaturę, slip speed, the type of lubricant), pressure, the type of material used on the bearings and shafts and their roughness, as well as contamination remaining in the system. This paper presents the roughness profiles co-operating with a rubber (NBR) and polytetrafluoroethylene (PTFE) bushes. The conditions of cooperation...
-
Glass-ceramic joining of Fe22Cr porous alloy to Crofer22APU: interfacial issues and mechanical properties
PublikacjaThis work deals with the joining of porous Fe22Cr ferritic stainless steel to a dense Crofer22APU plate by using a silica-based, Ba-containing glass-ceramic. The chemical and interfacial stability and the mechanical properties of the joints were evaluated before and after thermal ageing at 700 ◦C for 500hrs. The sintering behaviour of the glass was assessed by using heating stage microscopy (HSM) to study the influence of a porous...
-
Properties of Barium Cerate Thin Films Formed Using E-Beam Deposition
PublikacjaThis article focuses on the properties of the BaCeO3 thin films formed by electron-beam vapor deposition and investigates the formation of barium cerates on supports with different thermal expansion coefficients (Stainless Steel, Invar, Glass Sealing, and Inconel substrates) and the influence of the technological parameters on the properties of the formed thin films with an emphasis on the stability of the films. Morphology and...
-
The assessment of metrological properties of segmental orifice based on simulations and experiments
PublikacjaSegmental orifices are often used to measure flows of heterogeneous mixtures, especially in flow meters in the power industry, for example. The orifice (with module m= 0.25) was installed in a stainless-steel pipe with internal diameter of 50 mm, placed in a hydraulic water system. The research was performed for Reynolds numbers ranging from 9,000 to 17,000. The flow characteristics of this orifice obtained based on simulation...
-
Plate heat exchanger with porous structure for potential use in ORC system
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The passive intensification was obtained by a modification of the heat transfer surface, which was covered by a metallic porous microlayer. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one...
-
Plate heat exchanger with porous structure for potential use in ORC system
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The passive intensification was obtained by a modification of the heat transfer surface, which was covered by a metallic porous microlayer. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one...
-
The influence of polymer bearing material and lubricating grooves layout on wear of journal bearings lubricated with contaminated water
PublikacjaThe goal of the present paper is to investigate wear properties of journal sliding bearing operating in the conditions of contaminated water lubrication. Several bearing materials and bearing sleeve designs (differing in the axial grooves position and their shape) were tested experimentally under typical operating conditions in a dedicated test rig, which was equipped with a lubricating system, enabling lubrication with contaminated...
-
Właściwości złączy różnoimiennych stopu niklu Incoloy 800H ze stalą odporną na korozję 316L
PublikacjaW artykule przedstawiono problemy związane z wykonywaniem połączeń różnoimiennych typu Incoloy 800HT – austenityczna stal odporna na korozję 316L. Wykonano badania nieniszczące oraz niszczące, których wyniki pozwoliły na weryfikacje jakości wykonanych złączy próbnych. Nie stwierdzono występowania niezgodności spawalniczych oraz uzyskano wysokie właściwości wytrzymałościowe złączy. Badania metalograficzne ujawniły poprawne struktury...
-
Selected local stability problems of channel section flanges made of aluminium alloys
PublikacjaThe paper addresses the issue of local buckling of compressed flanges of cold-formed thin-walled channel columns and beams with nonstandard flanges composed of aluminium alloys. The material behaviour follows the Ramberg–Osgood law. It should be noted that the proposed solution may be also applied for other materials, for example: stainless steel, carbon steel. The paper is motivated by an increasing interest in nonstandard cold-formed...
-
The FEM analysis of pressure installation elements after simulated accidental overheating
PublikacjaThe paper presents innovative analysis focused on the safety aspects of existing pressure installation operation after overheating accidents. Results presented here can be applied in decision-making process concerning further operation of existing pressure installation after cooling system failure. In this paper the results of FEM analysis performed for a straight pipe and 90 degrees elbow, made of super duplex stainless steel,...
-
Study of nanomechanical properties of (1-y)BST-yMgO thin films
PublikacjaIn the present study thin films of MgO – modified Ba0.6Sr0.4TiO3 (BST60/40) solid solution were prepared by the sol-gel-type chemical solution deposition method on stainless steel substrates. A multilayer spin-coating approach was utilized for the Ba0.6Sr0.4TiO3-MgO thin film deposition with subsequent thermal annealing at T=650-750C. Dried BST60/40-MgO gel powders were studied with thermogravimetric and differential thermal analysis...
-
Chapter 8 – Active Sampling of Air
PublikacjaThis chapter reviews the literature information on analytical techniques and laboratory equipment used for active sampling of air (atmospheric and indoor) in regular monitoring research. It describes popular analytical devices applied for sample collection using various types of polymeric bags, e.g. Tedlar bags, Teflon or Nafion bags, and/or stainless steel vacuum containers. It reviews literature data about the application of...
-
A study of cavitation erosion resistance of an ion nitrided titanium alloy by means of the vibration and rotating disk methods
PublikacjaIn this work, a comparative analysis of the cavitation erosion resistance of the Ti– 6.7Al–2.5Mo–1.8Cr–0.5Fe–0.25Si alloy (known as brand VT3-1) before and after lowtemperature ion nitriding is carried out. Two test methods were applied, using vibrative (ASTM G-32) and rotating disk rigs, respectively. The kinetic dependences of the erosive destruction of samples of titanium alloy VT3-1 in the initial state, after ion nitriding...
-
Wpływ rodzaju zanieczyszczenia powierzchni odlewu ze staliwa LH14 na jakość napoin wykonanych elektrodą otuloną
PublikacjaNapawanie jest szeroko stosowaną metodą naprawiania powierzchni. Pozwala między innymi na uzupełnienie miejsc, w których uprzednio wystąpiły wżery korozyjne. Techniki napawania wykorzystywane są również do przywracania pierwotnego kształtu zużytych części. W pracy wykonano badania napoin wykonanych elektrodami otulonymi na czołowych powierzchniach cylindrycznych próbek ze staliwa LH14. Proces wykonywano dwoma rodzajami elektrod:...
-
Fabrication and Crystal Structure of Sol-Gel Deposited BST Thin Films with Compositional Gradient
PublikacjaIn the present research technology of compositionally graded barium strontium titanate Ba1-xSrxTiO3 thin films deposited on stainless steel substrates by sol-gel spin coating followed with thermal annealing at T = 650°C is reported. Results of thermal behavior of the sol-gel derived powders with compositions used for fabrication of graded structure (i.e. with Sr mole fraction x = 0.5, 0.4 and 0.3) are described. X-ray diffraction...
-
Piezoresponse force microscopy and dielectric spectroscopy study of Ba0.6Sr0.4TiO3 thin films
PublikacjaResearch on synthesis, characterization and determination of processing – structure – property relationships of commercially important ferroelectric thin films has been performed. The sol-gel-type solution deposition technique was applied to produce good quality thin films of Ba0.6Sr0.4TiO3 (BST60/40) chemical composition on the stainless steel substrates. The thin films were characterized in terms of their microstructure, crystal...
-
Wstępne badania technologii spawania złączy narożnych ze stali niskoweglowej i nierdzewnej o grubości g=6mm i g=10mm
PublikacjaCelem pracy był dobór parametrów spawania dla spoin narożnych o grubości 6mm i 10mm próbek wykonanych ze stali niskowęglowej S355 i stali nierdzewnej - typu 304 (X6CrNI18-10). Złącza były spawane laserowo, jednostronnie z pełnym przetopem a powierzchnie lica i grani zapewniają uzyskanie szczelności przylegającego elementu uszczelniającego. Próbki zostały dostarczone przez Zleceniodawcę. Próby zostały przeprowadzone na stanowisku...