Filtry
wszystkich: 838
wybranych: 716
Wyniki wyszukiwania dla: CIRCUIT MINIATURIZATION
-
Effect of the let-through energy of overcurrent protective devices on the temperature of conductors during short-circuits
PublikacjaThe scope of the verification of low-voltage systems covers the earth fault loop impedance measurement. This measurement is usually performed with the use of low-value current meters, which force a current many times lower than the one occurring during a real short-circuit. Therefore, the international standard recommends consideration of the increase of resistance of conductors with the increase of temperature, which may occur...
-
Constrained multi-objective optimization of compact microwave circuits by design triangulation and pareto front interpolation
PublikacjaDevelopment of microwave components is an inherently multi-objective task. This is especially pertinent to the design closure stage, i.e., final adjustment of geometry and/or material parameters carried out to improve the electrical performance of the system. The design goals are often conflicting so that the improvement of one normally leads to a degradation of others. Compact microwave passives constitute a representative case:...
-
Fault diagnosis in electronic circuits based on bilinear transformation in 3-D and 4-D spaces
PublikacjaPrzedstawiono ideę nowych metod diagnostycznych 3-D i 4-D opartych na przek-ształceniu biliniowym. Metody te bazują na transformacjach operujących odpo-wiednio w trzy i czterowymiarowych przestrzeniach funkcji układowych. Dlatych metod omówiono algorytm lokalizacji i identyfikacji pojedynczych uszko-dzeń parametrycznych w liniowych układach elektronicznych oraz algorytm lo-kalizacji i identyfikacji pojedynczych uszkodzeń...
-
Effect of the various fats on the structural characteristics of the hard dough biscuit
Publikacja -
Effects of lightning and sprites on the ionospheric potential, and threshold effects on sprite initiation, obtained using an analog model of the global atmospheric electric circuit
Publikacja -
Transient States during Short-circuit in a Line Powered by UPS and its Impact on Earth Fault Loop Impedance Measurement and Power Quality
PublikacjaThe short-circuit in a line powered by Uninterruptible Power Supply (UPS) during different UPS operation modes is presented in the article. The transient state condition related to the short-circuit in a line fed from double conversion On-line UPS is discussed in detail. The results of the measurements of earth fault loop impedance (FLI) in circuits powered by UPS with the instruments of various manufacturers are presented. The...
-
On Decision-Making Strategies for Improved-Reliability Size Reduction of Microwave Passives: Intermittent Correction of Equality Constraints and Adaptive Handling of Inequality Constraints
PublikacjaDesign optimization of passive microwave components is an intricate process, especially if the primary objective is a reduction of the physical size of the structure. The latter has become an important design consideration for a growing number of modern applications (mobile communications, wearable/implantable devices, internet of things), where miniaturization is imperative due to a limited space allocated for the electronic circuitry....
-
Fast EM-Driven Parameter Tuning of Microwave Circuits with Sparse Sensitivity Updates via Principal Directions
PublikacjaNumerical optimization has become more important than ever in the design of microwave components and systems, primarily as a consequence of increasing performance demands and growing complexity of the circuits. As the parameter tuning is more and more often executed using full-wave electromagnetic (EM) models, the CPU cost of the overall process tends to be excessive even for local optimization. Some ways of alleviating these issues...
-
Design and multi-objective optimization of combinational digital circuits using evolutionaty algorithm with multi-layer chromosomes
PublikacjaW artykule przedstawiono zastosowanie algorytmów ewolucyjnych z wielowarstwowymi chromosomami do projektowania i optymalizacji wielokryterialnej kombinatorycznych układów cyfrowych. Kryteriami optymalizacji były: liczba bramek, liczba tranzystorów w układzie i czas propagacji sygnałów. Proponowaną metodą zaprojektowano i optymalizowano cztery układy wzięte z literatury. Uzyskane rezultaty porównano z wynikami otrzymanymi innymi...
-
New Two-center Ellipsoidal Basis Function Neural Network for Fault Diagnosis of Analog Electronic Circuits
PublikacjaIn the paper a new fault diagnosis-oriented neural network and a diagnostic method for localization of parametric faults in Analog Electronic Circuits (AECs) with tolerances is presented. The method belongs to the class of dictionary Simulation Before Test (SBT) methods. It utilizes dictionary fault signatures as a family of identification curves dispersed around nominal positions by component tolerances of the Circuit Under Test...
-
Atomistic Surrogate-Based Optimization for Simulation-Driven Design of Computationally Expensive Microwave Circuits with Compact Footprints
PublikacjaA robust simulation-driven design methodology for computationally expensive microwave circuits with compact footprints has been presented. The general method introduced in this chapter is suitable for a wide class of N-port un-conventional microwave circuits constructed as a deviation from classic design solutions. Conventional electromagnetic (EM) simulation-driven design routines are generally prohibitive when applied to numerically...
-
Topological model of aptitude of the measurement circuits of main subassemblies of an internal combustion engine crankshaft-piston assembly
PublikacjaThe paper presents a topological model allowing to determine the probability of aptitude of the diagnosing system (SDG) individual measuring circuits and also to determine to what degree they influence the assessment of the technical condition of an arbitrary main subassembly of crankshaft-piston assemblies as a diagnosed system (SDN).
-
On performance limits of switched-capacitor multi-phase charge pump circuits. Remarks on papers of Starzyk et al.
PublikacjaW pracy zweryfikowano hipotezę Starzyka nt. maksymalnego, osiągalnego wzmocnienia napięciowego w wielotaktowym konwerterze napięcia stałego typu C-przełączane (w tzw. pompie ładunkowej). W konwerterze zbudowanym z k kondensatorów maksymalne wzmocnienie określone jest przez odpowiednią potęgę liczby 2 tj. 2^(k-1) przy czym warunek podany przez Starzyka jest konieczny lecz nie jest dostateczny. Podano warunki konieczne i dostateczne...
-
Reducing average and peak temperatures of VLSI CMOS circuits by means of evolutionary algorithm applied to high level synthesis.
PublikacjaW pracy przedstawiono adaptacyjny algorytm ewolucyjny zastosowany do syntezy wysokiego poziomu układów cyfrowych CMOS w celu zredukowania pobieranej przez nie mocy. Prowadzi to do redukcji szczytowej i średniej temperatury układu scalonego. Dzięki temu uzyskuje się wzrost niezawodności projektowanych układów scalonych.
-
Cost-Efficient Multi-Objective Design of Miniaturized Microwave Circuits Using Machine Learning and Artificial Neural Network
PublikacjaDesigning microwave components involves managing multiple objectives such as center frequencies, impedance matching, and size reduction for miniaturized structures. Traditional multi-objective optimization (MO) approaches heavily rely on computationally expensive population-based methods, especially when exe-cuted with full-wave electromagnetic (EM) analysis to guarantee reliability. This paper introduces a novel and cost-effective...
-
High gain/bandwidth off‑chip antenna loaded with metamaterial unit‑cell impedance matching circuit for sub‑terahertz near‑field electronic systems
PublikacjaAn innovative off-chip antenna (OCA) is presented that exhibits high gain and efficiency performance at the terahertz (THz) band and has a wide operational bandwidth. The proposed OCA is implemented on stacked silicon layers and consists of an open circuit meandering line. It is shown that by loading the antenna with an array of subwavelength circular dielectric slots and terminating it with a metamaterial unit cell, its impedance...
-
A filter bank solution for active power filter control algorithms
PublikacjaThb paper describes the proposed active power fiIter (APF) with a new control circuit based on an algorithm using ufilter bank and a harmonic predictor. The conirol circuit was realized using the digiiaI signor processor ADSP-21065L and FPGA circuiL In the proposed circuit transient performunee of APF is improved The active power fdter circuil has been built and teste6 and some illustrative, experimental results are uIso presented...
-
Method of earth fault loop impedance measurement without nuisance tripping of RCDs in 3-phase low-voltage circuits
PublikacjaVerification of electrical safety in low-voltage power systems includes the measurement of earth fault loop impedance. This measurement is performed to verify the effectiveness of protection against indirect contact. The widespread classic methods and meters use a relatively high value of the measuring current (5–20) A, so that they are a source of nuisance tripping of residual current devices (RCDs). The meters dedicated to circuits...
-
An Efficient Framework For Fast Computer Aided Design of Microwave Circuits Based on the Higher-Order 3D Finite-Element Method
PublikacjaIn this paper, an efficient computational framework for the full-wave design by optimization of complex microwave passive devices, such as antennas, filters, and multiplexers, is described. The framework consists of a computational engine, a 3D object modeler, and a graphical user interface. The computational engine, which is based on a finite element method with curvilinear higher-order tetrahedral elements, is coupled with built-in...
-
Expedited Re-Design of Multi-Band Passive Microwave Circuits Using Orthogonal Scaling Directions and Gradient-Based Tuning
PublikacjaGeometry scaling of microwave circuits is an essential but challenging task. In particular, the employment of a given passive structure in a different application area often requires re-adjustment of the operating frequencies/bands while maintaining top performance. Achieving this necessitates utilization of numerical optimization methods. Nonetheless, if the intended frequencies are distant from the ones at the starting point,...
-
Novel doubly perforated broadband microstrip branch-line couplers
PublikacjaTwo broadband compact doubly perforated hybrid couplers have been designed, manufactured, and measured. To improve frequency characteristics and to reduce circuit dimensions, two kinds of perforations have been introduced: the defected ground structures in the ground plane metallization and photonic bandgap cells in the strip metallization. Measurement results show essential miniaturization (~39% and ~36%) and enhancement of the...
-
On Design Optimization of Miniaturized Microscrip Dual-Band Rat-Race Coupler with Enhanced Bandwidth
PublikacjaIn the paper, a novel topology of a miniaturized wideband dual-band rat-race coupler has been presented. Small size of the circuit has been obtained by meandering transmission lines of the conventional circuit. At the same time, the number of independent geometry parameters has been increased in order to secure sufficient circuit flexibility in the context of its design optimization for dual-band operation. Optimum dimensions of...
-
Nestling Diet and Parental Provisioning Behaviour in the Marsh Harrier (Circus aeruginosus)
Publikacja -
Low-Cost Automated Design of Compact Branch-Line Couplers
PublikacjaBranch-line couplers (BLCs) are important components of wireless communication systems. Conventional BLCs are often characterized by large footprints which make miniaturization an important prerequisite for their application in modern devices. State-of-the-art approaches to design of compact BLCs are largely based on the use of high-permittivity substrates and multi-layer topologies. Alternative methods involve replacement of transmission-line...
-
A CMRC-based compact rat-race coupler with harmonic suppression
PublikacjaIn this paper, an eective miniaturization technique exploiting compact microstrip resonant cells has been discussed and experimentally validated on the basis of a 3-dB microstrip rat-race coupler. The application of the method proposed has resulted in 91 % circuit area reduction in comparison to a conventional rat-race coupler. Experimental results show good agreement with theoretical characteristics, as well as an additional eect,...
-
A structure and design optimization of novel compact microscrip dual-band rat-race coupler with enhanced bandwidth
PublikacjaIn the letter, a topology of a novel compact wideband dual-band rat-race coupler has been presented along with its computationally efficient design optimization procedure. Reduction of the circuit size has been achieved by meandering transmission lines of the conventional circuit. At the same time, the number of independent geometry parameters has been increased so as to secure sufficient flexibility of the circuit, necessary in...
-
Offshore surface waters of Antarctica are free of microplastics, as revealed by a circum-Antarctic study
PublikacjaIn 2018, during a circum navigation of Antarctica below 62° S by the sailing boat Katharsis II, the presence of plastics was investigated with surface sampling nets at ten evenly spaced locations (every 36° of longitude). Although fibres that appeared to be plastic (particles up to 2 cm) were found in numbers ranging from 1 particle (0.002 particles per m3) to 171 particles (1.366 particles per m3) per station, a Fourier-transform...
-
Seasonal and spatial variation of the Montagu’s Harrier’s Circus pygargus diet in Eastern Poland
Publikacja -
A Comprehensive Survey on Antennas On-Chip Based on Metamaterial, Metasurface, and Substrate Integrated Waveguide Principles for Millimeter-Waves and Terahertz Integrated Circuits and Systems
PublikacjaAntennas on-chip are a particular type of radiating elements valued for their small footprint. They are most commonly integrated in circuit boards to electromagnetically interface free space, which is necessary for wireless communications. Antennas on-chip radiate and receive electromagnetic (EM) energy as any conventional antennas, but what distinguishes them is their miniaturized size. This means they can be integrated inside...
-
Impedancje i składowe prądu zaburzeń w obwodach z łącznikami półprzewodnikowymi = Impedances and disturbance current components in the circuits with semiconductor switches
PublikacjaW referacie przedstawiono pewien sposób określenia impedancji i składowych prądu zaburzeń dla przypadku obwodu z łącznikiem półprzewodnikowym. Określono widmową impedancje obciążenia i impedancje wewnętrzną źródła oraz rozpływy składowych prądu zaburzeń. Zaprezentowano wyniki obliczeń dla pewnego przypadku obwodu. W wnioskach omówiono wpływ przyjętego układu zastępczego źródła zaburzeń oraz częstotliwości charakterystycznej na...
-
Expedited Optimization of Passive Microwave Devices Using Gradient Search and Principal Directions
PublikacjaOver the recent years, utilization of numerical optimization techniques has become ubiquitous in the design of high-frequency systems, including microwave passive components. The primary reason is that the circuits become increasingly complex to meet ever growing performance demands concerning their electrical performance, additional functionalities, as well as miniaturization. Nonetheless, as reliable evaluation of microwave device...
-
COMPARISON OF SYSTEM ON CHIP TECHNOLOGIES FOR SPACE APPLICATIONS
PublikacjaThe paper presents a review of technologies available for the implementation of digital and mixed signal systems, particularly the system on a chip (SoC) for space applications. The phenomena encountered in the space environment are briefly presented, together with the known solutions, regarding the design of complex electronic systems. The most important norms regarding single die integrated circuits designed for space are also...
-
Microstrip line with short-circuited edge as a high-pass filter operating up to millimeter-wave frequencies
PublikacjaPrzedstawiono prosty planarny filtr górnoprzepustowy wykorzystujący linię mikropaskową ze zwartym brzegiem. Układy zaprojektowano w taki sposób, aby pasmo przepustowe rozpoczynało się w zakresie K lub Ka. Wykonano dwa prototypy: na podłożu w postaci warstwy dielektrycznej wykonanej z ceramiki alundowej oraz na podłożu organicznym o niskiej przenikalności elektrycznej. Wykazano dużą zgodność teoretycznych i pomierzonych charakterystyk...
-
Identyfikacja parametrów zastępczego schematu elektrycznego krwiobiegu nerki na podstawie niepełnych danych pomiarowych : The parameters identification of the equivalent electric circuit of the kidney blood circulation basis on incomplete measuring date
PublikacjaW referacie przedstawiono metodę identyfikacji parametrów elektrycznego schematu zastępczego odwzorowującego przepływ krwi przez nerkę. Napięcie potraktowano jako sygnał wejściowy, któremu w hemodynamice odpowiada ciśnienie, natomiast prąd jako sygnał wyjściowy, któremu odpowiada przepływ krwi. Przebieg napięcia aproksymowano funkcją sklejaną w celu uproszczenia procedury pomiarowej i ograniczenia fluktuacji związanych z przebiegiem...
-
Technika wyłączania, zmniejszająca skutki zwarć łukowych. - Tł. z Plant Engineering, March 2007. - Tyt. oryg.: Circuit breaker technology reduces arc flash risk / Patricia E. Chandler
PublikacjaW artykule podano sposoby zmniejszania skutków zwarć łukowych oraz opisano zalety nowoczesnych wyłączników ograniczających prądy zwarciowe. Podano możliwości układów elektronicznych w monitorowaniu parametrów elektrycznych instalacji, stanu pracy wyłączników i wykrywaniu zwarć.
-
A testing method of analog parts of mixed-signal electronic systems equipped with the IEEE1149.1 test bus
PublikacjaA new solution of the JTAG BIST for testing analog circuits in mixed-signal electronic microsystems controlled by microcontrollers and equipped with the IEEE1149.1 bus is presented. It is based on a new fault diagnosis method in which an analog circuit is stimulated by a buffered signal from the TMS line, and the time response of the circuit to this signal is sampled by the ADC equipped with the JTAG. The method can be used for...
-
Development of a compact microstrip resonant cell aimed at efficient microwave component size reduction
PublikacjaA comprehensive comparison of a wide collection of compact microstrip resonant cells (CMRCs) found in the extensive body of literature has been presented. The evaluation of different CMRC designs has led to the selection of the most promising CMRC geometry for the efficient miniaturisation of modern microwave components. In order to showcase the vital effectiveness of the approach, the initially selected CMRC has been notably...
-
Design and optimisation of combinational digital circuits using modified evolutionary algorithm.Projektowanie i optymalizacja kombinacyjnych układów cyfrowych przy użyciu zmodyfikowanego algorytmu ewolucyjnego.
PublikacjaW pracy przedstawiono możliwości projektowania i optymalizacji układów kombinacyjnych przy użyciu zmodyfikowanych algorytmów ewolucyjnych. Modyfikacja algorytmów polega na wprowadzeniu chromosomów wielowarstwowych i operatorów działających na nich. Wyniki projektowania czterech układów kombinacyjnych uzyskanych uzyskane tą metodą porównano z następującymi metodami opisanymi w literaturze jak: Mapy Karnaugh, metoda Quine-McCluskey...
-
A compact seven-section rat-race hybrid coupler incorporating pbg cells
PublikacjaA conventional rat-race coupler has been doubly miniaturized: (i) characteristic impedances and electrical lengths of microstrip sections have been adequately modified as the first step of size reduction and (ii) T-shaped PBG cells have been implemented to diminish strip section length as the second step of circuit rat-race couplerminiaturization. The experimental results show good agreement with theoretical characteristics. Furthermore,...
-
Expedited EM-Driven Design of Miniaturized Microwave Hybrid Couplers Using Surrogate-Based Optimization
PublikacjaMiniaturization of microwave hybrid couplers is important for contemporary wireless communication engineering. Using standard computer-aided design methods for development of compact structures is extremely challenging due to a general lack of computationally efficient and accurate simulation models. Poor accuracy of available equivalent circuits results from neglecting parasitic cross-couplings that greatly affect the performance...
-
Miniaturized dual‐band branch‐line coupler with enhanced bandwidth
PublikacjaIn this letter, a miniaturized hybrid dual-band branch-line coupler (BLC) with enhanced fractional bandwidths is proposed. Compact size and bandwidth enhancement are obtained using meandered transmission line sections with broken symmetry between cross-coupling branches. The circuit is designed at a low numerical cost using surrogate-assisted techniques. The optimized design features small size of only 0.25λg×0.19λg(28% miniaturization...
-
Cross-border transmission line configuration influence on the electrical power and energy billing process
PublikacjaIn 2015 a connection between the Polish and Lithuanian power systems become fully operational. The connection consists of a 400 kV double circuit transmission line and a back-to-back HVDC substation located on the Lithuanian side. A magnetic couplings between the circuits of the transmission line cause that during power transmission a different values of active power losses are observed in both circuits. This situation may cause...
-
Characteristics of an image sensor with early-vision processing fabricated in standard 0.35 µm CMOS technology
PublikacjaThe article presents measurement results of prototype integrated circuits for acquisition and processing of images in real time. In order to verify a new concept of circuit solutions of analogue image processors, experimental integrated circuits were fabricated. The integrated circuits, designed in a standard 0.35 µm CMOS technology, contain the image sensor and analogue processors that perform low-level convolution-based image...
-
Bandwidth-size design trade-offs for compact spline-parameterised patch couplers by means of electromagnetic-driven multi-objective optimisation
PublikacjaBroad bandwidth and small size are the key performance figures for contemporary microwave couplers. These requirements are conflicting, i.e. improvement of one generally leads to degradation of the other assuming fixed topology of the circuit at hand. From a designer's perspective, the knowledge about available design trade-offs is indispensable as it permits for tailoring the circuit for particular applications as well as comparing...
-
The Issues of Reactive Power Compensation in High-voltage Transmission Lines
PublikacjaThis paper discusses the selection of compensation shunt reactors for a double-circuit 400 kV transmission line using the example of the newly built Elk Bis – Alytus transmission line. The analysis takes into account various conditions of the power system. The published results relate to voltage levels in steady states and during switching processes and short circuits.
-
Expedited Geometry Scaling of Compact Microwave Passives by Means of Inverse Surrogate Modeling
PublikacjaIn this paper, the problem of geometry scaling of compact microwave structures is investigated. As opposed to conventional structures (i.e., constructed using uniform transmission lines), re-design of miniaturized circuits (e.g., implemented with artificial transmission lines, ATSs) for different operating frequencies is far from being straightforward due to considerable cross-couplings between the circuit components. Here, we...
-
Slow-wave fractal-shaped compact microstrip resonant cell
PublikacjaA novel fractal-shaped compact microstrip resonant cell (CMRC) featuring a strong slow-wave effect has been presented. Its vital usefulness in the process of microstrip line miniaturisation has been proved and experimentally validated on the basis of a compact 3-dB branch-line coupler illustrating the possibilities of the approach. A prototype example structure has been designed to mirror the characteristics of a conventional device,...
-
Zastosowanie oprogramowania COMSIS do oceny dynamicznej odporności na zakłócenia cyfrowych układów kombinacyjnych.
PublikacjaWyniki badania odporności układów cyfrowych na zakłócenie dynamiczne w istotny sposób zależą od parametrów sygnału stymulującego. Proponowana metodyka zakłada pobudzanie badanego układu sygnałem szumu białego o określonej szerokości pasma częstotliwości. Badania symulacyjne z modelem układu progowego oraz szybkiego komparatora z histerezą przeprowadzono w środowisku COMSIS. Uzyskane wyniki potwierdzają, że im węższe pasmo szumu...
-
Nested Space Mapping Technology for Expedite EM-driven Design of Compact RF/microwave Components
PublikacjaA robust simulation-driven methodology for rapid and reliable design of RF/microwave circuits comprising compact microstrip resonant cells (CMRCs) is presented. We introduce a nested space mapping (NSM) technology, in which the inner space mapping layer is utilized to improve the generalization capabilities of the equivalent circuit model corresponding to a constitutive element of the circuit under consideration. The outer layer...
-
Rapid Simulation-Driven Multiobjective Design Optimization of Decomposable Compact Microwave Passives
PublikacjaIn this paper, a methodology for fast multiobjective optimization of the miniaturized microwave passives has been presented. Our approach is applicable to circuits that can be decomposed into individual cells [e.g., compact microstrip resonant cells (CMRCs)]. The structures are individually modeled using their corresponding equivalent circuits and aligned with their accurate, EM simulated...