Filtry
wszystkich: 757
wybranych: 696
Wyniki wyszukiwania dla: LIGTHWEIGHT CONCRETE
-
Experimental Study of the Resistance to Influence of Aggressive Liquids on Lightweight Concrete
PublikacjaIn light of the scientific research, the corrosion of concrete structures is one of the main problems that may reduce their durability due to the negative impact of the natural environment. The paper analyzes the influence of the type of component on the selected properties of lightweight concrete subjected to the influence of aggressive liquids. Four concrete mixes were prepared with a granular aggregate made of foamed glass (GEGA)...
-
Study of the Resistance to Influence of Aggressive Liquids on Concrete with Lightweight Aggregate
PublikacjaThe corrosion of the structure of concrete caused by the aggressive external environment is one of the main problems that can reduce the durability of buildings. The paper analyzes the influence of the type of component on selected properties of lightweight concrete (LWC) exposed to aggressive liquids. When lightweight concrete containing porous aggregates is used, the influence of an aggressive environment may be of particular...
-
Preliminary Studies on a Lightweight Porous Cement-Based Composite – Gel Concrete
Publikacja -
BEHAVIOR OF REINFORCED CONCRETE BEAMS CONTAINING LIGHTWEIGHT AGGREGATE IN THE TENSILE ZONE
Publikacja.
-
Application of Artificial Neural Networks to Predict Insulation Properties of Lightweight Concrete
PublikacjaPredicting the properties of concrete before its design and application process allows for refining and optimizing its composition. However, the properties of lightweight concrete are much harder to predict than those of normal weight concrete, especially if the forecast concerns the insulating properties of concrete with artificial lightweight aggregate (LWA). It is possible to use porous aggregates and precisely modify the composition...
-
Thermal and Strength Properties of Lightweight Concretes with Variable Porosity Structures
Publikacja -
Thermal and strength properties of lightweight concretes with the addition of aerogel particles
Publikacja -
Thermal performance of building envelopes with structural layers of the same density: Lightweight aggregate concrete versus foamed concrete
Publikacja -
Investigation of Durability Properties for Lightweight Structural Concrete with Hemp Shives Instead of Aggregate
Publikacja -
Cost Analysis of Prefabricated Elements of the Ordinary and Lightweight Concrete Walls in Residential Construction
PublikacjaGlobal economic growth causes an increase in natural resources exploitation, particularly in construction branch. The growing use of electricity contributes to climate change. Therefore, it is necessary to search the solutions, which will allow for reducing natural resources exploitation. One of the many opportunities to do that is the application of the recycled materials. The authors of the given article have analyzed three variants...
-
Experimental and Numerical Investigation of Mechanical Properties of Lightweight Concretes (LWCs) with Various Aggregates
PublikacjaHigh requirements for the properties of construction materials and activities directed at environment protection are reasons to look for new solutions in concrete technology. This research was directed at solutions affecting the reduction of energy consumption and CO2 emissions. The use of lightweight concretes (LWCs) allows one to meet both conditions at the same time. The purpose of the research presented in this paper was to...
-
Improving Thermal Insulation Properties for Prefabricated Wall Components Made of Lightweight Aggregate Concrete with Open Structure
PublikacjaPorous concrete is commonly used in civil engineering due to its good thermal insulation properties in comparison with normal concrete and high compression strength in comparison with other building materials. An extremely porous concrete, called ‘lightweight aggregate concrete with open structure’ (LAC), is used in some German plants to produce prefabricated wall components. They are used mainly in hall buildings, e.g. supermarkets....
-
Predicting Performance of Lightweight Concrete with Granulated Expanded Glass and Ash Aggregate by Means of Using Artificial Neural Networks
PublikacjaLightweight concrete (LWC) is a group of cement composites of the defined physical, mechanical, and chemical performance. The methods of designing the composition of LWC with the assumed density and compressive strength are used most commonly. The purpose of using LWC is the reduction of the structure’s weight, as well as the reduction of thermal conductivity index. The highest possible strength, durability and low thermal conductivity...
-
Synthesis of the zeolites on the lightweight aluminosilicate fillers
Publikacja -
Lightweight structures in architecture: scenarios for the future
PublikacjaLightweight structures - structures with a reduced weight, which otherwise retain the qualities necessary for the building performance, ensuring a proper durability and strength, safety, indoor environmental quality and energy efficiency; stuctures which strive for the optimization of structural systems - are in tune with current trends and socio-economic, environmental and technological factors. The growing interest in the lightweight...
-
Utilization of shale cuttings in production of lightweight aggregates
PublikacjaThe development of technologies for unconventional hydrocarbon exploration requires designing procedures to manage drilling waste that are consistent with the waste management hierarchy. In view of this, the possibility to apply shale drill cuttings as a prospective additive (replacing bentonite) to fly ash used for the production of lightweight aggregates (LWAs) was investigated. Moreover, a facile, waste-free method of LWAs production...
-
Advances in Sheet Metal Forming Processes of Lightweight Alloys
Publikacja -
Modeling and Simulation of Electric Motors Using Lightweight Materials
Publikacja -
Dynamic effect of the vehicle passing under lightweight footbridge.
PublikacjaThe paper describes a numerical study of dynamic response of cable-stayed steel footbridge for a big lorry passing underneath. The footbridge is an existing object crossing Wolska street in Warsaw. The structural model of footbridge was verified by dynamic test loading. A numerical study of a vehicle passing under footbridge is presented. 2D and 3D incompressible flow fields are modeled using sliding mesh in transient CFD computation....
-
Probabilistic Methods in Reliability Assessment of Engineering Lightweight Structures
PublikacjaThe paper considers the probability-based analysis of structural safety measures. Two different numerical examples of representative lightweight structures are considered – a submerged truss tower supporting an offshore platform, and an overhead power line support truss tower. On the basis of these examples, the importance of a motivated selection of analysis method and a proper choice of the number of important variables is shown....
-
Manufacturing of Lightweight Aggregates as an Auspicious Method of Sewage Sludge Utilization
Publikacja: Sewage sludge is a high-volume and low-cost waste commonly generated worldwide, so its utilization is a vital issue. The application of this waste in the manufacturing of lightweight aggregates was investigated. The process was performed using intensive mixers with volumes of 5 and 30 L, as well as the industrial 500 L mixer. Then, granulates were sintered in a tube furnace. The influence of composition and mixer size on the...
-
Influence of stirrups in a concrete shell on strengthening reinforced concrete column
PublikacjaTwelve concrete columns, with a 150x150mm square section and three columns with a circular section (d=200mm), are tested to investigate the effect of strengthening by RC jacket. Based on a confined concrete model for axial static loading, an analytical methods, reported in the literature are proposed to predict the behavior of columns with RC jacket. The results support the conception that the effect of strengthening depends...
-
Lightweight Cement Mortars with Granulated Foam Glass and Waste Perlite Addition
Publikacja -
Lightweight glass and metal roof structures in the 19th century. Architecture and construction.
PublikacjaThe 19th century brought new construction possibilities. The usage of metal elements in mesh structures, filled in with glass, resulted in creating entirely new types of objects. They have distinguished themselves in architecture and technical solutions. The envelope structures giving spatial interiors were arising very quickly. They have been enabling large light penetration, triggering them extremely bright. Thus these building...
-
Application of lightweight cement composite with foamed glass aggregate in shell structures
PublikacjaThe purpose of the paper is to investigate the abilities of applying Granulated Expanded Glass Aggregate (GEGA) as a natural volume substitute of aggregate as a component of lightweight concrete. The GEGA aggregates used in the experiments were made of confused glass waste. In order to achieve satisfactory strength of concrete Granulated Ash Aggregate (GAA) was added as well. To produce specimens three grain sizes of aggregates...
-
Analysis od dynamic loads on lightweight footbridge caused by lorry passing underneath
PublikacjaW artykule przedstawiono analizę drgań lekkiej kładki dla pieszych wywołanych przejazdem ciężarówki z dużą prędkością pod spodem konstrukcji.
-
Accurate Lightweight Calibration Methods for Mobile Low-Cost Particulate Matter Sensors
PublikacjaMonitoring air pollution is a critical step towards improving public health, particularly when it comes to identifying the primary air pollutants that can have an impact on human health. Among these pollutants, particulate matter (PM) with a diameter of up to 2.5 μ m (or PM2.5) is of particular concern, making it important to continuously and accurately monitor pollution related to PM. The emergence of mobile low-cost PM sensors...
-
The use of lightweight aggregate saturated with PCM as a temperature stabilizing material for road surfaces.
PublikacjaThis paper presents the possibility of adding lightweight building aggregates to increase the stability – mechanical as well as thermal - of constructions and road objects. This stability can be achieved through saturating the porous granules of aggregate with a phase-change material (PCM) that allows the accumulation of solar heat. Intense solar radiation, especially during the summer, can cause the asphalt on road surfaces, bridges...
-
Towards a Lightweight Approach for the Evaluation of Requirements Engineering Impact on Other IT Project Areas
PublikacjaRequirements Engineering (RE) is recognized as one of the most important, but difficult areas of software engineering, with a significant impact on other areas of the IT project and its final outcome. The empirical studies investigating this impact are hard to conduct, mainly due to large effort required. It is thus difficult for researchers and even more for industry practitioners to make evidence-based evaluations, how decisions...
-
Effect of porosity on physical properties of lightweight cement composite with foamed glass aggregate
PublikacjaThis paper reports on a study of physical properties of lightweight cement composite. We investigate the possibility of replacing traditional aggregate with Granulated Ash Aggregate (GAA) and above all with Granulated Expanded Glass Aggregate (GEGA). For this purpose, 15 specimens of different percentage share of each aggregate in total aggregate volume were tested: 0%, 25%, 50%, 75% or 100% of foam glass aggregate (GEGA) partially...
-
A Compact and Lightweight Microwave Tilt Sensor Based on an SRR-Loaded Microstrip Line
PublikacjaIn this paper, the symmetry property of split ring resonators (SRRs) is exploited to develop a tilt sensor. The sensor is composed of an SRR-loaded microstrip line operating at microwave frequencies. It is shown that the depth of notch in the reflection characteristic of the microstrip is a function of the tilt angle of the SRR. Thus, it can be used for sensing inclination. The sensor benefits from very compact size and light weight....
-
Multifaceted Analyses of Four Different Prototype Lightweight Photovoltaic Modules of Novel Structure
PublikacjaDynamic growth of photovoltaic capacity in Poland encourages many entities to invest in photovoltaic systems. However, in the case of buildings with low roof-bearing capacity it can be problematic or even impossible to mount conventional PV modules due to their relatively high weight. Hence, the use of lightweight PV modules is a potential solution. In this paper four different prototype silicon lightweight modules of novel structure...
-
Evaluation of Mechanical Properties of Two-Stage Concrete and Conventional Concrete Using Nondestructive Tests
PublikacjaDifferent types of concrete mixtures are used as building materials. The manufacturing process of two-stage concrete (TSC) differs from that of conventional concrete. This study investigated conventional mechanical properties derive empirical relations for estimation of the mechanical parameters of TSC and conventional concrete mixtures. TSC was used to prepare 216 specimens and conventional concrete was used to prepare 108 specimens...
-
Simple empirical formula to estimate the main geomechanical parameters of preplaced aggregate concrete and conventional concrete
PublikacjaPreplaced aggregate concrete (PAC) or two-stage concrete is a specific type of concrete successfully employed in many projects including underwater concrete structures, massive concrete structures, structures made of reinforced concrete, and improvement of concrete structures. PAC is significantly different than the conventional concrete. In this type of concrete, aggregates are initially poured into the mold, the voids between...
-
Standard and modified falling mass impact tests on preplaced aggregatefibrous concrete and slurry infiltrated fibrous concrete
PublikacjaAlthough several studies have been conducted to evaluate the impact response of concrete using theAmerican Concrete Institute (ACI) 544-2R falling mass impact test, the variations in test results are themain drawback of this testing method. This study aims to reduce the variations in experimental impacttest results by introducing two simple test setup modifications; (1) using coarse or fine aggregate bed-ding as an alternative...
-
Evaluation of the resistance of steel–concrete adhesive connection in reinforced concrete beams using guided wave propagation
PublikacjaThe development of the nondestructive diagnostic methods is of significant importance in the last decades. A special attention is paid to diagnostics of reinforced concrete structures, which are very popular in the civil engineering field. A possible use of the guided waves in the estimation of the resistance of steel–concrete adhesive connection is studied in the following paper. The relationships relating adhesive connection...
-
Concrete elements cast in febric forms
PublikacjaPrzedstawiono wyniki badań wytrzymałościowych elementów betonowych wylewanych w wiotkich formach wykonanych z materiałów syntetycznych. Badania przeprowadzono dla modelu ściany/słupa. Zbadano mechaniczne i chemiczne własności 10 różnych materiałów syntetycznych. Wybrano materiał o przepuszczalności umożliwiającej wykonanie monolitycznej konstrukcji. Z 12 zbadanych mieszanek betonowych do dalszej analizy wyselekcjonowano trzy. Badania...
-
Numerical simulation of hardening of concrete plate
PublikacjaThe paper presents a theoretical formulation of concrete curing in order to predict temperature evolution and strength development. The model of heat flow is based on a well-known Fourier equation. The numerical solution is implemented by means of the Finite Difference Method. In order to verify the model, the in situ temperature measurements at the top plate of a road bridge were carried out. A high agreement between numerical...
-
Simulation of fracture process in fibrous concrete
PublikacjaArtykuł omawia wyniki modelowania procesu zarysowania w elementach betonowych zawierające stalowe włókna przy zastosowaniu dyskretnego modelu kratownicowego. Beton był modelowany na poziomie mezoskali z uwzględnieniem 5 faz: kruszywa, zaczynu cementowego, włókien i obu stref kontaktu. Obliczenia wykonano dla jednoosiowego ściskania oraz jednoosiowego rozciągania.
-
Mesoscopic modelling of strain localization in concrete
PublikacjaArtykuł omawia obliczenie lokalizacji odkształceń w elementach betonowych poddanych zginaniu. Obliczenia wykonano dla betonu na poziomie mezo przy zastosowaniu modelu zniszczeniowego z degradacją sztywności rozszerzonego o nielokalność. Zbadano wpływ zagęszczenia kruszywa, wielkość kruszywa, kształtu kruszywa oraz długości charakterystycznej na szerokość lokalizacji.
-
Towards development of sustainable lightweight 3D printed wall building envelopes – Experimental and numerical studies
Publikacja -
Comparison of low-temperature cracks intensity on pavements with high modulus asphalt concrete and conventional asphalt concrete bases
PublikacjaHigh modulus asphalt concrete (HMAC) base courses provide very good resistance to rutting and fatigue but they can increase the risk of low-temperature cracking as compared with conventional asphalt concrete (AC). The article presents the comparison of these two road materials in terms of low-temperature cracking. The statistical method based on the ordered logistic regression model was used. The analysis was based on results of...
-
Lightweight alkali-activated composites containing sintered fly ash aggregate and various amounts of silica aerogel
Publikacja -
Damage Detection of Steel-Concrete Composite Beam
Publikacja -
Uniform corrosion monitoring of carbon steel in concrete
Publikacja -
Concrete-domain reasoning techniques in knowledge cartography
PublikacjaWiele zjawisk w świecie rzeczywistym opisujemy korzystając z liczb i symboli. W ramach naszej pracy jako punkt wyjścia traktujemy podejście kartograficzne opracowane na potrzeby wnioskowania z ontologii opartych na logice opisowej i pozwalające na efektywne przetwarzanie baz wiedzy zwierających dużą liczbę osobników. Niniejszy artykuł przedstawia rozszerzenie podejścia kartograficznego pozwalające na wnioskowanie z wartości symbolicznych,...
-
Impregnation vibro-pressed concrete pavement bricks.
PublikacjaW materiałach przedstawiono wyniki badań uzyskanych podczas prób impregnacji wibroprasowanych elementów betonowych. Celem badań było określenie odpowiedniego składu kompozycji impregnacyjnej, aby uzyskać najlepszy efekt zabezpieczenia powierzchni betonu przed wnikaniem cieczy organicznych np. oleju mineralnego.
-
Uniform corrosion monitoring of carbon steel in concrete.
PublikacjaW przypadku korozji prętów zbrojeniowych w żelbecie zaobserwowane zostały obszary wzmożonego zaatakowania. Pomiar prądowego i napięciowego szumu elektrochemicznego umożliwia wyznaczenie szybkości korozji ogólnej a zmiany parametrów statystycznych przebiegów szumowych umożliwiają detekcję występowania przestrzennych rejonów intensyfikacji korozji. Przedstawione rezultaty, oparte na wykorzystaniu odpowiedniego układu zastępczego,...
-
Ultrasound monitoring for evaluation of damage in reinforced concrete
PublikacjaThe paper deals with automated monitoring of damage evolution in concrete elements subjected to three-point bending tests. The monitoring is based on the nonlinear interactions of traveling ultrasonic waves with micro-crack zones inside the concrete specimens and surface-breaking cracks. The developed procedure assumes semi-continuous ultrasonic testing during the element full loading cycle and generation of the power spectral...
-
Experimental tests of reinforced concrete deep-beams
PublikacjaThe paper presents results of experimental research of the reinforced concrete deep beam with a spatial arrangement. Tested structural elements consist of the cantilever deep beam loaded on the height and transverse deep beam with hanging on it another one. The analysis includes crack morphology, effort of steel and load distribution. The article verified effectiveness of two different kind of reinforcement in both tested deep...