Filtry
wszystkich: 1355
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: 316l steel
-
Modification of cement-ash composites with steel fibre addition
PublikacjaPraca zawiera wyniki badań kompozytów cementowo-popiołowych, w których popiół zastosowano jako częściowy zamiennik cementu. Do kompozytów dodano niewielkie ilości dwóch rodzajów włókien stalowych. Zbadano właściwości techniczne kompozytów. Wytrzymałości kompozytów cementowo-popiołowych z włóknami stalowymi w stosunku do wytrzymałości kompozytów bez włókien po wszystkich okresach wiązania i twardnienia były wyższe od kilku do kilkudziesięciu...
-
Experimental tests of steel double-type balcony connections
PublikacjaThe paper presents analysis and results of experimental tests of full scale prefabricated balcony sets with dimensions (width × length × height): 2.0 m × 2.78 m × 0.186 m (in slope to 0.17 m). The sets consists of reinforced concrete slabs (balcony and ceiling) connected with each other by double-type balcony connections. The paper analyses the impact of variable parameters on the load carry capacity of elements. Additionally...
-
Effectiveness of Concrete Reinforcement with Recycled Tyre Steel Fibres
Publikacja -
PROBLEMS WITH CORROSION PROTECTION STEEL STACKS IN FGD SYSTEMS
PublikacjaThis paper presents problems associated with corrosion of steel stacks and changes in philosophy of corrosion protection when implemented into flue gas desulphurization systems. In-situ tests were taken by means of electrochemical impedance spectroscopy at a stack which discharges flue gas before wet lime/limestone desulphurization. A very rapid soaking of spherical infill vinylester coating with electrolyte has been observed....
-
THE INFLUENCE OF POLYMER STRIPS IN REDUCTION OF A STEEL GRANDSTAND VIBRATIONS
PublikacjaGrandstands are types of structures commonly used during sport events or music concerts. Dynamic loads generated by crowd movement may have significant influence on human perception as well as may lead to the destruction of a structure. Lighter and more slender structural steel members are more easily excitable by spectators. If the synchronized movement is tuned with the natural frequency of the affected part of the structure,...
-
Earthquake-induced pounding between asymmetric steel buildings
PublikacjaEarthquake-induced pounding between buildings has been the subject of numerous numerical and experimental studies in the resent years. The phe-nomenon may cause severe damage to structural elements as well as may also lead to the total collapse of colliding structures. A major reason leading to pounding between adjacent, insufficiently separated buildings results from the differences in their dynamic properties. The aim of this...
-
Earthquake-Induced Pounding Between Asymmetric Steel Buildings
PublikacjaEarthquake-induced pounding between buildings has been the subject of numerous numerical and experimental studies in the resent years. The phenomenon may cause severe damage to structural elements as well as may also lead to the total collapse of colliding structures. A major reason leading to pounding between adjacent, insufficiently separated buildings results from the differences in their dynamic properties. The aim of this...
-
Wettability of Horizontal Stainless Steel Tube by Nanofluid Droplets
PublikacjaThe goal of the present work was the experimental determination of the contact angle of three nanofluids, i.e. water-Al2O3, water-Cu and water-TiO2 on horizontal stainless steel tube of 1.6 mm OD. Of particular interest was the effect of nanoparticle concentration (0.01%, 0.1%, and 1% by weight) on droplet contact angle.
-
Heat tint colours on stainless steel and welded joints
PublikacjaSurface layer condition of stainless steels and welded joints influences strongly their corrosion resistance. This problem seems to be underestimated. This current study explains the phenomenon of heat tint forming on welds, the methods of its removal, inspection procedures after heat tint removing and post weld finishing
-
INFLUENCE OF CERAMIC COATING ON MECHANICAL PROPERTIES OF STAINLESS STEEL
PublikacjaCrystal structure and phase composition of stainless steel substrates (AISI 304 type) was studied and it was found that they adopted the cubic symmetry. The calculated elementary cell parameter for the mayor Fe-Ni phase (weight fraction 99%) was a = 3.593 Å, whereas the mean grain size was = 2932 Å. Morphology of the stainless steel substrate surface was studied with profilometry. Mechanical properties of the stainless steel...
-
COLD CRACKING OF S460N STEEL WELDED IN WATER ENVIRONMENT
PublikacjaThis paper shows results of weldability testing of fine-grained high -strength low- alloy S460N steel welded in water environment by covered electrodes. The tests were carried out by using the CTS test specimens with fillet welds. Four specimens were welded under water and one specimen in air. Welded joints were subjected to non-destructive visual and penetration tests. The accepted joints were then subjected to macroscopic and...
-
Wettability of Horizontal Stainless Steel Tube by Nanofluid Droplets
PublikacjaThe goal of the present work was the experimental determination of the contact angle of three nanofluids, i.e. water-Al2O3, water-Cu and water-TiO2 on horizontal stainless steel tube of 1.6 mm OD. Of particular interest was the effect of nanoparticle concentration (0.01%, 0.1%, and 1% by weight) on droplet contact angle.
-
Adhesion of organic coatings to hot-dip galvanized steel
PublikacjaDuplex systems provide long-time corrosion protection, much longer than the sum of the lifetimes of zinc and paint used individually. However loss of adhesion between coating and zinc substrate is often found in practice. Different methods of zinc surface preparations are used in the fi eld. The aim of this study was to examine and compare coating protection when the old zinc surface, stored during long-time period (15 years) in...
-
Degradation of ferritic X10CrAlSi18 stainless steel caused by slurry
PublikacjaThe slurry erosion tests of ferritic X10CrAlSi18 steel were carried out using a slurry pot device. In order to investigate the erosion process, two series of tests were performed: first one with a constant impact velocity of 5 m/s, 7 m/s and 9 m/s and the second one, during which the impact velocity was changed after every exposure. During each test, an influence of test conditions on volume loss, surface hardness and roughness...
-
Corrosion degradation impact on mechanical properties of structural steel
PublikacjaRecently, extensive research was conducted regarding the impact of corrosion degradation on the mechanical properties of structural steel. Studies show that at the material level, the microstructure is somewhat unchanged due to corrosion degradation. However, the corrosion causes pits and structural surface irregularities that consequently impact the mean stress-strain response of typical coupon specimens subjected to tensile loading....
-
Axial capacity of steel built-up battened columns
PublikacjaThis paper deals with the numerical investigation aimed to study the axial capacity of pin-ended steel built-up columns. Three methods of calculating forces in chords and batten, taking into account the material and geometric imperfections specified in the Eurocode 3 are considered. The aim of this study was to compare different methods allowing the calculation of the column load capacity and determine a simpler and faster method...
-
Bead-on-Plate Underwater Wet Welding on S700MC Steel
PublikacjaThe participation of high strength steels in marine and offshore structures is increasing, which makes it necessary to develop recommendations for underwater repair welding works. The article presents the results of bead-on-plate welded specimens made of S700MC high strength steel in underwater wet welding conditions by covered elec- trodes. Three specimens with heat input values in the range 0.91-1.05 kJ/mm were made. The specimens...
-
APPLICATION POSSIBILITIES OF THE S960 STEEL IN UNDERWATER WELDED STRUCTURES
PublikacjaIn this paper, the application possibilities of the ultra-high strength (UHSS). Domex 960 steel in the underwater welded structures are analyzed. In the research, the investigated material has been tested in bead-on-plate wet welding conditions with the usage of different heat input values, namely 0.63 kJ/mm, 0.72 kJ/mm and 0.93 kJ/mm. Specimens were performed by the manual metal arc (MMA) welding method with the usage of rutile...
-
Reservoir Influence on Pressure Wave Propagation in Steel Pipes
PublikacjaThe relation between the length of steel pipe and the pressure wave period in the system, reservoir-pipe-valve, is discussed. Experiments carried out for the short steel pipes showed that in such a system, the pressure wave celerity estimated using the measured wave cycles systematically increases with the increase of the pipe length. The observed differences can exceed even 90 m=s. As the pressure wave traveling in the pipe with...
-
Cavitation Erosion of P110 Steel in Different Drilling Muds
PublikacjaThe P110 steel specimens were subjected to ultrasonic cavitation erosion in different compositions of drilling muds and surfactant additive. The test procedure was based on ASTM-G-32 standard recommendations. API 5CT-P110 steel is used for pipes in oil and gas industry. The harsh environment and high velocity of flows poses corrosive and erosive threat on materials used there. The composition of drilling fluid influences its rheological...
-
Modeling the application of steel slag in stabilizing expansive soil
PublikacjaThe objective of this study was to evaluate the suitability of steel slag as an additive to the engineering properties of weak clay soil. Different geotechnical laboratory tests were conducted on both stabilized and natural soils. Steel slag (SS) was added at a rate of 0, 5, 10, 15, 20, and 25% to the soil. Specific gravity, grain size analysis, Atterberg limit test, compaction test, free swell, California bearing ratio (CBR),...
-
Steel-fibrous concrete -experiments and a numerical discrete model
PublikacjaW książce przedstawiono wyniki doświadczalne i numeryczne dotyczące rys w elementach betonowych wzmocnionych włóknami stalowymi dla różnych problemów brzegowych quasi-statycznych. Obliczenia wykonano przy zastosowaniu własnego oryginalnego modelu sieciowego. W modelu beton z włóknami stalowymi był modelowany na poziomie mezo. W obliczeniach uwzględniono strefy kontaktu miedzy kruszywem a zaczynem oraz włóknami a zaczynem.
-
SEM micrographs of the austenitic stainless steel corrosion in asphalt fumes
Dane BadawczeThe dataset contains the scanning electron microscopy (SEM) studies of the austenitic stainless steels: AISI 304, AISI 316, AISI 321 and duplex stainless steel AISI 2205. The samples were polished and exposed to the installation carrying asphalt fumes at elevated temperatures (approx. ~210-240 Celsius). The exposition duration was three months. Some...
-
A dissimilar welded joint of grade 92 steel and AISI 304L steel obtained using IN82 buttering and IN617 fller: relationship of microstructure and mechanical properties
PublikacjaUnfavourable operating conditions of equipment in the energy industry resulting from high-temperature loads determine the need to use special materials and technological solutions, including welding procedures. In this article, buttering using IN82 (ERNiCr-3) consumables was proposed as a method to improve the weldability of grade 92 steel joined by the gas tungsten arc welding (GTAW) process with AISI 304L (IN617 fller). The...
-
R and D: Research and Development Kobe Steel Engineering Reports
Czasopisma -
SEAISI Quarterly (South East Asia Iron and Steel Institute)
Czasopisma -
Experimental and numerical studies of double corrugated steel arch panels
Publikacja -
Thermal Fatigue Influence of Laser Treated Tool Steel Surface
Publikacja -
Application of guided waves in the evaluation of steel-concrete adhesive connection
Publikacja -
APPLICATION OF NUMERICAL SIMULATIONS ON X10CRWMOVNB9-2 STEEL MULTILAYER WELDING
Publikacja -
The influence of plastic deformation on the magnetoelastic properties of the CSN12021 grade steel
PublikacjaWłasności magnetosprężyste materiałów są silnie modyfikowane przez zmiany struktury dyslokacyjnej, które są wynikiem procesów deformacji plastycznej. Zmiany te mogą być wykorzystane jako podstawa do opracowania metody nieniszczącej oceny stopnia deformacji materiału.Jak dotychczas zaproponowane zostały różne metody, oparte na pomiarach pętli histerezy magnetycznej czy też natężenia magnetycznego efektu Barkhausena. Artykuł porównuje...
-
Search for optimum geometry of selected steel sandwich panel joints
PublikacjaZastosowanie stalowych paneli typu sandwich w konstrukcjach okrętowych wymaga rozwiązania wielu problemów. Jednymi z trudniejszych zagadnień związanych z tymi nowymi strukturami są połączenia pomiędzy panelami oraz między panelami i konstrukcją innego typu. Artykuł przedstawia poszukiwanie optymalnej geometrii połączenia typu panel-panel w układzie wzdłużnym, przy użyciu parametrycznego modelu w programie ANSYS. Poszukiwano konfiguracji...
-
Estimation of the parameters of the discrete model of a steel–concrete composite beam
Publikacja -
Experimental research of the stability of steel cylindricalshell subjected to circumferential compression
PublikacjaAt the Department of Metal Structures Gdańsk University of Technology, experiments have been performed on the stability of shell of steel cylindrical models. The experiments have been carried on a test bench built at the Department. The design based on other test benches which were created in the past by other scientists, where modernized by the courtesy of companies that offer modern solutions. The test bench enables to generate...
-
Influence of burnishing on stress corrosion cracking susceptibility of duplex steel
PublikacjaNa próbkach ze stali duplex poddanych procesom nagniatania przeprowadzono badania podatności do naprężeniowego pękania korozyjnego. Przeprowadzono testy odkształcania z małą prędkością w środowisku wrzącego 35% MgCl2 i środowisku obojętnym- glicerynie. Stwierdzono zwiększoną odporność korozyjną stali po procesach nagniatania z niewielkim stopniem zgniotu. Stwierdzono, że zgniot powierzchniowy ma wpływ na przebieg procesu korozyjnego...
-
Fatigue life tests of steel laser-welded sandwich structures
PublikacjaW publikacji zaprezentowano rezultaty systematycznych badań trwałości zmęczeniowej elementarnych połączeń wykonanych techniką spawania laserowego dla różnych wariantów geometrii złącz. Pokazano uzyskane wyniki i ich aproksymację, porównano uzyskane rezultaty dla różnych geometrii.
-
Tests of local strains in steel laser - welded sandwich structure
PublikacjaW publikacji zaprezentowano rezultaty badań odkształceń w strefie spoiny laserowej konstrukcji sandwich. Pokazano obiekt badań, metodykę i oprzyrządowanie oraz proces rejestracji. Przedstawiono uzyskane wyniki i wnioski z nich wypływające.
-
Mechanical properties and corrosion resistance of dissimilar stainless steel welds
PublikacjaW artykule przedstawiono właściwości mechaniczne oraz odporność korozyjną doczołowych złączy różnoimiennych stali odpornych na korozję, austenitycznej 316L oraz duplex 2205. Blachy o grubości 15 mm spawano automatycznie łukiem krytyn z różnymi energiami liniowymi. Wykazano, że właściwości mechaniczne złączy spełniają wymagania okrętowych towarzystw klasyfikacyjnych, natomiast najbardziej narażoną strefą złącza na działanie korozji...
-
Efect of ageing on microstructure and impact properties of 9Cr-1Mo steel
PublikacjaBadano wpływ długotrwałego starzenia na mikrostrukturę i właściwości udarnościowe trzech przemysłowych wytopów stali typu 9Cr-1Mo. Wczesniejsze badania wykazały, że w stali 9Cr-1Mo starzonej w 550C przez 10 000 godzin występuje kruchość odpuszczania, a przy dłuższych czasach ekspozycji tworzy się krucha faza Lavesa (FeCr)2Mo na granicach ziaren. Powoduje to wzrost teperatury przejściowej kruchości oraz spadek energii łamania powyżej...
-
Influence of stress on oxidation behaviour of carbon steel studded coil.
PublikacjaAnalizowano awarię wężownicy kołkowej ze stali węglowej pracującej przez 10 lat w środowisku przegrzanej pary w temperaturze 290ºC i ciśnieniu 0,67 MPa. Obserwacje mikroskopowe powierzchni i przekroju rury ukazały drobne pęknięcia w ściance wynikające z procesu selektywnego utleniania. Zastosowano metodę elementów skończonych w celu ustalenia zależności postępu korozji od ciśnienia i obciążenia cieplnego.
-
Assessment of structural changes in IN-519 cast steel reformer tubes.
PublikacjaPrzedstawiono zmiany struktury rur katalitycznych ze staliwa austenitycznego IN-519 po długotrwałej eksploatacji w reformerze metanu.
-
Hydrogen degradation of the 26H2MF alloy steel in H2SO4 and hydrocarbon environments.
PublikacjaSTAL 26H2MF ZOSTALA PODDANA RÓZNEJ OBRÓBCE CIEPLNEJ, PO KTÓREJ UZYSKAŁA ONA RÓŻNĄ MIKROSTRUKTURĘ ORAZ CHARAKTER PRZEŁOMU. WYKONANO PRÓBY POWOLNEGO ODKSZTAŁCANIA W ROZCIEŃCZONYM KWASIE SIARKOWYM, PALIWIE CIĘZKIM I PRZEPRACOWANYM OLEJU SILNIKOWYM PRZEPRACOWANYM.
-
Cementite transformation in low carbon steel under the influence of sulphur.
PublikacjaBadano cementyt (węglik Fe3C) w przemysłowym gatunku stali niskowęglowej po długotrwałej eksploatacji w benzynie ciężkiej, zawierającej 0,3 ppm siarki, o temperaturze 200-220C. Wykazano, że cementyt na powierzchni i we wnętrzu stali ulega przemianie w niestabilną, quasi-krystaliczną fazę wzbogaconą w siarkę i pierwiastki domieszkowe a zubożoną w żelazo. Przemiana cementytu i rozpad zdegradowanej fazy związana jest z uwolnieniem...
-
Crack Mouth Opening Displacement for EH36 Shipbuilding Steel Measurements
PublikacjaThe dataset titled EH36 steel for shipbuilding (plate thicnkness 50mm) - CMOD - force record, a0/W = 0.6 contains CMOD (Crack Mouth Opening Displacement) - Force record which is the base for evaluation of fracture toughness of structural steel. Bend specimens witch Bx2B section (B= 50mm), and relative initial crack length a0 / W = 0.60 were used. The test was carried out at ambient temperature in accordance to ISO 12135 standard....
-
Influence of Material Thickness on the Ductile Fracture of Steel Plates for Shipbuilding
PublikacjaIn the shipbuilding industry, the risk of brittle fractures is relatively high because some units operate in arctic or subarcticzones and use high thickness (up to 100 mm) steel plates in their structures. This risk is limited by employing certifiedmaterials with a specific impact strength, determined using the Charpy method (for a given design temperature) and byexercising control over the welding processes (technology qualification,...
-
Hydrogen delayed cracking of high-strength 14hnmbcu steel in seawater
PublikacjaOceniano podatność na niszczenie wodorowe stali o wysokiej wytrzymałości i jej połączeń spawanych przy stałym obciążeniu w wodzie morskiej. Badania przeprowadzono na próbkach okrągłych z karbem w środowisku wody morskiej przy potencjale korozyjnym oraz przy polaryzacji katodowej. Badano stal gatunku 14HNMBCu o minimalnej granicy plastyczności 690 MPa oraz jej połączenia spawane automatycznie łukiem krytym i ręcznie łukowo elektrodą...
-
Surface treatment of C80U steel by long CO2 laser pulses
PublikacjaThe paper presents the results of laser-melted C80U steel. The processed steel was placed between two permanent magnets and laser beam whose scanning velocity was 10 mm/s. CO2 laser beam was working in pulse mode. Pulses were generated at 100% of the average preset power of 700W, with 45 ms irradiation, zero interval between pulses and beginning of pulse repetition upon the achievement of the average laser power. During the operation,...
-
The degradation mechanisms of a nanobainitic steel under cavitation erosion conditions
Publikacja -
Evaluation of recycled tyre steel fibres adhesion to cement matrix
Publikacja -
Application of polymer element in reduction of temporary steel grandstand vibrations
PublikacjaThe numerical analysis focused on reduction of vibrations of a temporary steel scaffolding grandstand has been conducted in this paper. These types of structures are regularly subjected to dynamic loads which, in conjunction with light and quite slender structural members, may induce dangerous vibrations. To increase their safety, temporary steel grandstands are usually strengthened with the diagonal stiffeners of tubular cross...