Wyniki wyszukiwania dla: POLYURETHANES
-
Analysis of Validation and Simplification of Timber-Frame Structure Design Stage with PU-Foam Insulation
PublikacjaThe transition from experimental studies to the realm of numerical simulations is often necessary for further studies, but very difficult at the same time. This is especially the case for extended seismic analysis and earthquake-resistant design. This paper describes an approach to moving from the experimental testing of an elementary part of a wood-frame building structure to a numerical model, with the use of a commercial engineering...
-
Removal of cyclohexane and ethanol from air in biotrickling filters inoculated with Candida albicans and Candida subhashii
PublikacjaThis paper presents investigations on the removal of cyclohexane and ethanol from air in polyurethane- -packed biotrickling filters, inoculated with Candida albicans and Candida subhashii fungal species. Results on process performance together with flow cytometry analyses of the biofilm formed over packing elements are presented and discussed. The results indicate that the presence of ethanol enhances the removal efficiency of cyclohexane...
-
Experimental study on polymer mass used to repair damaged structures
PublikacjaA new method of repairing damaged structures by injecting the cracks with specially designed polymer mass (flexible two-component grout based on polyurethane resin) has been recently proposed. The technique is mainly dedicated to damaged masonries, especially historical structures where minimum intervention is permitted. The cracks are filled with the special injection, forming the flexible joints bonding the disrupted structural...
-
Tyre/road noise reduction of poroelastic road surface tested in a laboratory
PublikacjaA so-called poroelastic road surface (PERS) is being developed in Europe. This contains a large percentage of rubber particles mixed with hard aggregate (stone and sand) and bound with polyurethane. This gives high air void content (around 30 %), high elasticity and smooth texture, all of which should give low noise properties. Inthis experiment anominally 30 mm thick sample of PERS was mounted on a steel drum. Various car tyres...
-
Poroelastic Low Noise Road Surfaces
PublikacjaNoise is one of the most important problems related to road traffic. During the last decades, noise emitted by engine and powertrain of vehicles was greatly reduced and tyres became a clearly dominant noise source. The paper describes the concept of low noise poroelastic road surfaces that are composed with mineral and rubber aggregate bound by polyurethane resin. Those surfaces have a porous structure and are much more flexible...
-
Ultra Low Noise Poroelastic Road Surfaces
PublikacjaNoise is one of the most important environmental problems related to road traffic. During the last decades, the noise emitted by the engines and powertrains of vehicles was greatly reduced and tires became a clearly dominant noise source. The article describes the concept of low noise poroelastic road surfaces that are composed of mineral and rubber aggregate bound by polyurethane resin. Those surfaces have a porous structure and...
-
Initial Field Validation of Poroelastic Pavement Made with Crumb Rubber, Mineral Aggregate and Highly Polymer-Modified Bitumen
PublikacjaTire/road noise in most driving conditions dominates other sources of traffic noise. One of the most efficient ways of reducing tire/road noise is to use the so-called “low noise pavement”. According to numerous studies, at present, poroelastic road pavement that is composed of rubber and mineral aggregate and polyurethane or bituminous binder gives the best noise reduction up to 12 dB. Unfortunately, there are many problems with...
-
PERS - QUIET ROAD SURFACE FOR URBAN AREAS
PublikacjaTraffic noise is one of the most important environmental problems in densely populated urban areas. At low speeds the tyre/road interaction dominates all other sources. It is anticipated that when electric and hybrid vehicles gain dominance in city traffic, the importance of tyre/road noise will still increase as electric engines are much less noisy than combustion engines. On the other hand, electric and hybrid urban vehicles...
-
Bitumen-Based Poroelastic Pavements: Successful Improvements and Remaining Issues
PublikacjaThis article presents the development process of designing and testing poroelastic pavement based on highly polymer-modified bitumen. Poroelastic wearing course was composed of mineral and rubber aggregate mixed with highly polymer-modified bitumen, in contrast to previous trials, during which polyurethane resins were mainly used as binder, which led to several serious technological problems concerning difficult production, insufficient...
-
Low noise poroelastic road pavements based on modified asphalt binder
PublikacjaTire/road noise is one of the most important environmental problems related to road traffic. As the most effective way to fight noise is reduction of sound emission from the source, a lot of work is being done to improve tire and road surfaces construction. This paper describes the first “road” results obtained within the SEPOR project, which is focused on developing a low noise poroelastic road surface based on bituminous binder....
-
Microwave radiation in the synthesis of urethane prepolymers
PublikacjaThis paper describes the use of microwave radiation in the synthesis of urethane prepolymers in bulk (without solvent). The prepolymers were synthesized using 1,6-hexamethylene diisocyanate (HDI) and poly (ε-caprolactone) diol (PCL) at a molar ratio of 4:1. The reaction was carried out without a catalyst in the reactor with a conventional heating system (oil bath) or in the microwave reactor (MW Reactor NOVA 09) at temperatures...
-
Study on the Structure-Property Dependences of Rigid PUR-PIR Foams Obtained from Marine Biomass-Based Biopolyol
PublikacjaThe paper describes the preparation and characterization of rigid polyurethane-polyisocyanurate (PUR-PIR) foams obtained with biopolyol synthesized in the process of liquefaction of biomass from the Baltic Sea. The obtained foams differed in the content of biopolyol in polyol mixture (0–30 wt%) and the isocyanate index (IISO = 200, 250, and 300). The prepared foams were characterized in terms of processing parameters (processing...
-
Thermal and Mechanical Behavior of Elastomers Incorporated with Thermoregulating Microcapsules
PublikacjaPolyurethane (PU) is one of the principal polymers in the global plastic market thanks to its versatility and continuous improvement. In this work, PU elastomeric materials having thermoregulating properties through the incorporation of microcapsules (mSD-(LDPE·EVA-RT27)) from low-density polyethylene and vinyl acetate containing paraffin®RT27 as PCM were produced. Elastomers were synthesized while varying the molar ratio [NCO]/[OH]...
-
A comparative study on selective properties of Kraft lignin–natural rubber composites containing different plasticizers
PublikacjaEffect of plasticizer type on the kraft lignin–nat- ural rubber composite microstructure and selected proper- ties was determined. The composites were prepared with addition of a commonly used naphthenic oil plasticizer to study the decomposition product of polyurethane (glyc- erolysate) and its characteristics. Kraft lignin powder was incorporated into the natural rubber matrix in amounts of 10 and 40 parts per 100 parts of natural...
-
The miniaturised emission chamber system and home-made passive flux sampler studies of monoaromatic hydrocarbons emissions from selected commercially-available floor coverings
PublikacjaThe estimation of the emission rate of organic compounds released from various types of indoor materials can be performed using stationary environmental test chambers (ETC) classified as ex-situ methods or small-scale portable analytical devices based on the use of passive technique at the stage of analytes sampling from the gaseous phase (in-situ methods). The paper presents results of emissions of selected organic compounds from...
-
From polymer waste to potential main industrial products: Actual state of recycling and recovering
Publikacjalastics have become widely used materials in everyday life due to their special properties such as durability, easy processing, light-weight and low-cost of production. However, because of their stable and non-biodegradable nature, postconsumer plastics become an issue to the environment. The growing amounts of waste are generated, as plastic products are commonly used only once before disposal. The alternatives of practical techniques...
-
Microcrystalline Cellulose Management in the Production of Poly(ether-urethane)s- Structure, Morphology, and Thermal Characteristic
PublikacjaIn response to the demand of polymer industry for reducing the use of synthetic chemicals, eco-friendly materials are investigated. In the presented study, bio-based poly(ether-urethane)s were prepared by using microcrystalline cellulose (MCC) and polyether polyol and 1,3-propanediol derived from corn sugar. A step towards sustainability was taken by incorporating bio-based compounds and cellulose, consequently, bio-waste are utilized...
-
Fungal co-culture improves the biodegradation of hydrophobic VOCs gas mixtures in conventional biofilters and biotrickling filters
PublikacjaThe present study systematically evaluated the potential of Candida subhashii, Fusarium solani and their consortium for the abatement of n-hexane, trichloroethylene (TCE), toluene and α-pinene in biofilters (BFs) and biotrickling filters (BTFs). Three 3.2 L BFs packed with polyurethane foam and operated at a gas residence time of 77 s with an air mixture of hydrophobic volatile organic compounds (VOCs) were inoculated with C. subhashii,...
-
Process control of air stream deodorization from vapors of VOCs using a gas sensor matrix conducted in the biotrickling filter (BTF)
PublikacjaThis article presents the validity, advisability and purposefulness of using a gas sensor matrix to monitor air deodorization processes carried out in a peat-perlite-polyurethane foam-packed biotrickling filter. The aim of the conducted research was to control the effectiveness of air stream purification from vapors of hydrophobic compounds, i.e., n-hexane and cyclohexane. The effectiveness of hydrophobic n-hexane and cyclohexane...
-
Highly Dissipative Materials for Damage Protection against Earthquake-Induced Structural Pounding
PublikacjaIt is a common situation that seismic excitations may lead to collisions between adjacent civil engineering structures. This phenomenon, called earthquake-induced structural pounding, may result in serious damage or even the total collapse of the colliding structures. Filling the gap between two buildings erected close to one another by using visco-elastic materials can be considered to be one of the most effective methods to avoid...
-
Development, characterization and evaluation of composite adsorbent for the adsorption of crystal violet from aqueous solution: Isotherm, kinetics, and thermodynamic studies
PublikacjaThe purpose of this work focuses on the production and investigations of a new composite material as alternative low-cost adsorbent for the removal of crystal violet (CV) dye from waste solution. The production method was performed by in-situ thermal activation technology via extrusion process of polymer wastes containing tire rubber (50 wt%) and polyurethane foam (50 wt%) using single-screw extruder under processing temperature...
-
Results of acoustic emission tests of corrosion protection degree of ship steel tanks covered by means of protective coatings (Phase I)
PublikacjaThis paper presents methods and results of the 1st series of tests of acoustic emission (AE) signals, aimed at assessing degree of corrosion protection of a tank made of hull structural steel, protected by means of a protective coating combined from polyurethane layer and concrete filler. The tests were carried outin compliance with a method specially elaborated for application to the work in question. In the method were used requirements...
-
THE INFLUENCE OF POLYMER STRIPS IN REDUCTION OF A STEEL GRANDSTAND VIBRATIONS
PublikacjaGrandstands are types of structures commonly used during sport events or music concerts. Dynamic loads generated by crowd movement may have significant influence on human perception as well as may lead to the destruction of a structure. Lighter and more slender structural steel members are more easily excitable by spectators. If the synchronized movement is tuned with the natural frequency of the affected part of the structure,...
-
Analysis of the Possibility of Using New Types of Protective Coatings and Abrasion-Resistant Linings under the Operating Conditions of the Spiral Classifier at KGHM Polska Miedź S.A. Ore Concentration Plant
PublikacjaA study was carried out to select the appropriate coatings for corrosion protection of the spiral classifier working at KGHM Polska Miedź S.A. Ore Concentration Plant. The abrasion resistance of selected protective coatings and wear-resistant linings was investigated using a DT-523 rotary abrasion tester with Taber CS-10 rubber abrasive discs. The average weight loss of the coatings after a cycle of 2000 revolutions was determined....