Publikacje
Filtry
wszystkich: 732
Katalog Publikacji
Rok 2013
-
ANALYSIS OF ROLLING RESISTANCE OF TIRES WITH RUN FLAT INSERT APPLYING DRUM METHOD AND RADIAL CHARACTERISTIC
PublikacjaThis paper presents analysis of rolling resistance of tires with RUN FLAT insert applying drum method and radial characteristic. The conducted studies indicated changes in operational properties of wheel, occurring as a result of inflation pressure drop in the wheel. As regards radial elasticity, such changes result in significant drop of radial rigidity and increase of static deflection and increase of tire rolling resistance....
-
Analysis of chemical composition and hardness of copper alloys = Badania składu chemicznego oraz twardości stopów miedzi
PublikacjaWykonano analizę składu chemicznego oraz badania twardości stopów miedzi zastosowanych na elementy łożyskowe. Sformułowano wnioski.
-
Analysis and comparision of safety of children and adult passanger in car based on crash tests results
PublikacjaThis paper presents analysis and comparision of safety of children and adult passanger in car based on crash tests results. The car crash test with four dummies, including two car seats allowed a direct comparison of the security under the same conditions of children and passengers directly to the car seat. Analysis of acceleration and video from the test allows to understand the phenomena during the collision, the air bags influence,...
-
Analiza obciążeń działających na dzieci w fotelikach zamocowanych przodem i tyłem w czasie zderzenia czołowego
PublikacjaW pracy omówiono podstawowe problemy ochrony dzieci w czasie kolizji drogowych. Przedstawiono dwa sposoby mocowania fotelików: przodem i tyłem do kierunku jazdy. Opisano i porównano przebiegi obciążeń głowy dziecka w czasie uderzenia pojazdu w sztywną ścianę betonową.
-
4-Point beam tensile test on a soft adhesive
PublikacjaAn adhesive butt joint with a soft bondline has been studied. A series of experiments was conducted on test pieces constituted of aluminium adherends bonded with a low modulus epoxy adhesive, ScotchWeld™ 2216. The joint was subjected to four point bending, in tension/compression loading, under constant deflection rate, with the bondline being parallel to the applied load. The objective was to examine and evaluate crack nucleation...
Rok 2014
-
Analysis of Rolling Resistance of Tires With Run Flat Insert
PublikacjaRun flat properties are required for tires intended for special applications like military or rescue vehicles. Run-Flat inserts make possible to drive a car or truck, with certain restrictions, also when inflation pressure is very low or non-existing (after tire damage). Rolling resistance of tires rolling the inserts increases considerably in relation to the rolling resistance of properly inflated tires. This paper presents results...
-
Analysis and Comparison of Safety of Children and Adult Passenger in Car Based on Crash Tests Results
PublikacjaMost important features of the child seat were presented. There was made analysis of selected dynamic loads acting on mannequins heads during a collision. Comparison of loads acting on the kid in a child seat and the other passengers in a car is presented. In analysis of the results particular attention has been paid on the children's secure in a car. The phenomena of collision child's occipital bone with seat backrest was described....
-
Analiza skupień jako metoda wspomagania decyzji zakupu urządzeń prądu stałego do spawania metodą TIG
PublikacjaW pracy podjęto zagadnienie wspomagania decyzji zakupu odpowiedniego spawalniczego źródła prądu. Zaproponowano rozwiązanie problemu z wykorzystaniem metod analizy skupień. Przedstawiono wyniki klasyfikacji 69 urządzeń prądu stałego do spawania TIG metodami Warda i k-średnich dla odpowiednio dobranego i przygotowanego zestawu cech diagnostycznych. Na podstawie wyników uznano, że analiza skupień może być skuteczną metodą wspomagania...
-
A New Microwave Ceramic – Polymer Composite with 0-3 Connectivity
PublikacjaGoal of the present research was to fabricate and study two-phase BiNbO4//PVDF composites with 0-3 connectivity. Such composite consists of there-dimensionally connected polymer matrix loaded with dielectric ceramic particles. In the present case BiNbO4 powder acted as an active phase (dispersed phase) whereas polyvinylidene fluoride (PVDF) acted as a non-active (passive) phase (matrix). BiNbO4//PVDF composites with the volume...
Rok 2017
-
Analysis of features of stainless steels in dissimilar welded joints in chloride inducted corrosion
PublikacjaStainless steels of femtic-austenitic microstructure that means the duplex Cr-Ni-Mo steels, in comparison with austenitic steel includes less expensive nickel and has much better mechanical properties with good formability and corrosion resistance, even in environments containing chloride ions. Similar share of high chromium ferrite and austenite, which is characterized by high ductility, determines that the duplex steels have...
-
Accurate rolling resistance Rolling resistance measurements can be influenced by a number of factors
PublikacjaTire rolling resistance is one of the most difficult-to-measure parameters of the tire/ pavement interface, especially if road measurements are required. First of all, it is necessary to measure a fairly small force in the system that is heavily loaded by other forces and subjected to many adverse effects causing measurement errors. The second problem is related to the fact that tire rolling resistance depends on many factors,...
-
3D Printing of Metallic Implants
PublikacjaThe fabrication of various elements, solid and open porous structures of stainless steel and Ti alloy is described. The process was started with the design of 3D models in CAD/CAM system. The 3D models were transformed into *.stl files and then the manufacturing process of the real structures by means of the selective laser melting with the SLM Realizer 100 3D printer was made. The paper shows the porous specimens made for possible...
Rok 2010
-
Analysis of Asymmetrical Rolling Process of Multilayer Plates
PublikacjaW niniejszej pracy przedstawiono wyniki badań numerycznych asymetrycznego procesu walcowania blach wielowarstwowych M1E-Al99,8-AlMg5. Modelowanie numeryczne procesu walcowania blach wielowarstwowych przeprowadzono w programie Forge 2D, którego obliczenia bazują na metodzie elementów skończonych. Przedstawione w pracy wyniki umożliwiły przeprowadzenie analizy procesu walcowania blach wielowarstwowych.
-
Allergic Reactions as a Defense of the Organism to the Influence of Implants Components Made of Stainless Steel
PublikacjaDue to the increasing number of cases of hypersensitivity caused by direct contact with metals, as well as the increasing demand for implants in humans all ages numerous studies on the effects of the impact of implant components are being carried out. The paper presents the phenomenon of etiology of allergy in general terms and in relation to the biomaterials used in medicine. There have been characterized in terms of impact on...
-
Allergic reactions as a defense of the organism to the influence of implants components made of stainless steel
PublikacjaDue to the increasing number of cases of hypersensitivity caused by direct contact with metals, as well as the increasing demand for implants in humans all ages numerous studies on the effects of the impact of implant components are being carried out. The paper presents the phenomenon of etiology of allergy in general terms and in relation to the biomaterials used in medicine. There have been characterized in terms of impact on...
Rok 2016
-
Analiza technologii lutowania próżniowego stali austenitycznej
PublikacjaCelem badań była ocena poprawności budowy złącza lutowanego próżniowo ze stali austenitycznej oraz analiza składu chemicznego charakterystycznych obszarów badanej próbki. Na podstawie badań wizualnych oraz metalograficznych na mikroskopie skaningowym (w tym analizy EDS) stwierdzono, że badane złącze charakteryzuje się prawidłową geometrią, jednak występują w nim liczne niezgodności (wydzielenia), co świadczy o nieprawidłowych parametrach...
Rok 2003
-
Analiza strukturalna stali 2H13 przetopionej wiązką lasera CO2
PublikacjaPrzedstawiono badania porównawcze mikrostruktury stali 2H13 po przetopieniu jej powierzchni wiązką lasera CO2 o mocy 6 kW i po konwencjonalnym hartowaniu. Badania wykazały niejednorodność składu chemicznego i twardości struktury otrzymanej w wyniku laserowego przetapiania stali 2H13.
-
Analiza stanu badań nanomateriałów i nanotechnologii w Polsce.
PublikacjaPrzedstawiono stan obecny badań polskich ośrodków naukowych w zakresie wytwarzania i właściwości materiałów nanokrystalicznych.
-
Analiza procesu zniszczenia kompozytu warstwowego aramidowo-szklanego przy zginaniu metodą in situ
PublikacjaPrzeprowadzono badania na zginanie in situ w komorze mikroskopu SEM kompozytów: winyloestrowego zbrojonego tkaniną aramidową i szklaną oraz epoksydowego zbrojonego hybrydową tkaniną aramidowo-szklaną. Otrzymano sekwencję obrazów postępującego zniszczenia laminatów. Określono przyczynę małej wytrzymałości laminatu winyloestrowego w porównaniu z laminatem epoksydowym o zadowalającej wytrzymałości.
-
Analiza procesu asymetrycznego walcowania blachy bimetalowej Al-Cu
PublikacjaW pracy określono wpływ asymetrii prędkości obwodowej walców na wygięcie blachy bimetalowej Al-Cu. Wprowadzenie asymetrycznego procesu walcowania do wytwarzania blach bimetalowych ma na celu zwiększenie prędkości płynięcia warstwy o większym oporze odkształcenia oraz zwiększenie równomierności rozkładu odkształcenia całkowitego na warstwy pasma. Ponadto w pracy określono optymalne wartości współczynnika asymetrii av, dla których...
-
Advanced vanadium modified steels for high pressure hydrogen reactors
PublikacjaPrzedstawiono nową generację stali chromowo-molibdenowych zmodyfikowanych wanadem, przeznaczonych do budowy wodorowych reaktorów i porównano ze stalami konwencjonalnymi. Opisano mikrostrukturę, właściwości i zastosowanie stali. Podkreślono wpływ mikrostruktury nowych stali na przebieg degradacji środowiskowej.
Rok 2002
-
Analiza składu chemicznego materiału rur fi1168,3x7,11
PublikacjaWykonano analizę składu chemicznego materiału rur oraz dokonano identyfikacji gatunku materiału.
Rok 2018
-
Analiza czynników związanych z warunkami przepływu zawiesiny i właściwościami cząstek wpływających na odporność hydroabrazyjną
PublikacjaDegradacja powierzchni materiałów spowodowana hydroabrazją zależy od czynników, które można podzielić na trzy główne kategorie: pierwsza związana z warunkami przepływu zawiesiny, druga z właściwościami cząstek stałych oraz trzecia z właściwościami badanego materiału. Czynniki kategorii pierwszej to czynniki mające wpływ na energię kinetyczną uderzenia i tym samym na szybkość erozji. Są to takie czynniki jak kąt uderzenia, prędkość...
-
A universal NDT method for examination of low energy impact damage in CFRP with the use of TLC film
PublikacjaThe article presents an attempt to use a sheet of laminated thermochromic liquid crystal film (TLC film) for non-destructive testing of the impact damage (energy values: 1J, 2J, 3J and 4J) in carbon fibre-reinforced polymer (CFRP). This is a new, alternative NDT approach based on the thermo-optical effect. The main advantages of this method are a) the low cost of TLC film, b) the low cost of recording devices due to the usage of...
Rok 2019
-
An Influence of Factors of Flow Condition, Particle and Material Properties on Slurry Erosion Resistance
PublikacjaThe degradation of materials due to slurry erosion is the serious problem which occurs in the power industries. The paper presents actual knowledge about an influence of individual factors connected with flow conditions, particles and material properties on the slurry erosion resistance. Among the factors connected with operating conditions, an influence of impact angle, and velocity of impact, particle concertation and liquid...
-
Advantages of the Application of the Temper Bead Welding Technique During Wet Welding
PublikacjaThermo-mechanically rolled S460ML steel was chosen for welding in underwater wet welding conditions by covered electrodes. The main aim of this study was to check the weldability for fillet welds in a water environment by controlled thermal severity (CTS) tests and to check the influence of temper bead welding (TBW) on the weldability of the investigated steel. Non-destructive and destructive tests showed that S460ML steel has...
Rok 2011
-
An in situ technique for the assessment of adhesive properties of a joint under load
PublikacjaSlow crack propagation in adhesive bonded joints has been characterised using an asymmetric wedge test. Crack position was evaluated from strain gauge measurements, both in the debonded partof the joint and in the bonded zone. Test temperature was changed during loading, giving insight into bond evolution. The technique allows accurate, and virtually continuous, determination of crack position to be made, and therefore the evaluation...
-
Adhesive compliance effect in mode I separation:Profilometry approach
PublikacjaThe effect of adhesive compliance on the deflection of a loaded, bonded beam was studied using laser profilometry. Experimental data obtained were compared with both Euler-Bernoulli (encastré) and Winkler (one parameter elastic foundation) models. A third, analytical, 2D model, based on shear within the adhesive layer (two parameter elastic foundation), was introduced. Finite element analysis (FEA) was also used to study the effect...
Rok 2015
-
An experimental study of high-hydrogen welding processes
PublikacjaThis paper presents investigation results of determination of the diffusible hydrogen content in deposited metal obtained by means of two most often used methods-the glycerin method and the mercury method. Relation has been defined between results of those methods in the area characteristic of low-hydrogen as well as high-hydrogen welding processes. Relations available in the literature do not include the diffusible hydrogen content...
Rok 2020
-
ALTERNATIVE, DIRECT SYNTHESIS METHOD OF THE CERAMIC SOLID SOLUTIONS BASED ON BaTiO3 THROUGH A HIGH ENERGY BALL MILLING
PublikacjaPolycrystalline samples BaTiO3 and the solid solutions Ba0.9Sr0.1TiO3, Ba0.9Sr0.1Ti0.9Sn0.1O3, Ba0.9Sr0.1Ti0.8Sn0.2O3 were obtained by means of a mechanochemical treatment based on the high-energy ball milling technique and next a high temperature solid state reaction method. The influence of synthesis condition on microstructural, dielectric and ferroelectric properties of obtained solid solutions were investigated. The structure...
-
A Critical Reanalysis of Uncontrollable Washboarding Phenomenon in Metal Band Sawing
PublikacjaThe article analyzes the cutting process of hard bars. Investigations conducted in industrial conditions demonstrated the presence of surface errors in the machined workpieces in the form of washboard patterns. The purpose of this study was to analyze the results of cutting on band sawing machines with different band saw blades. The cutting processes were conducted on three different horizontal band sawing machine types. Analyzed...
Rok 2009
-
Allergy to implant components: chromium, nickiel, cobalt and titanium
PublikacjaImplant jest kompozycja roznych pierwiastkow: niklu, chromu, kobaltu, tytanu, molibdenu i wanadu. Pierwiastki te moga doprowadzic do alergii, egzemy i obluzowania implantu.