Publikacje
Filtry
wszystkich: 750
Katalog Publikacji
Rok 2013
-
Selection of excitation signals for high-impedance spectroscopy
PublikacjaA method of fast impedance spectroscopy of technical objects with high impedance (|Zx| > 1 GOhm) is evaluated in this paper. An object is excited with a signal generated by a digital-to-analog converter (DAC) located on the U2531A DAQ module. Response signals proportional to current flowing through and voltage across the measured object are sampled by analog-to-digital converters (ADC) in the DAQ module. The object impedance spectrum...
-
Role of nitrogen in evolution of sp2/sp3 bonding and optical band gap in hydrogenated carbon nitride
PublikacjaDrastic changes in the bonding are found in amorphous hydrogenated carbon nitride (a-CNx:H) film as a function of nitrogen concentration (or N/C ratio). The total C-sp3 fraction and hardness shows a sharp decrease (at N/C = 0.40) whereas optical band gap and resistivity shows a gradual increase as nitrogen concentration increases from 0.07 to 0.58. Raman spectrum of a-CNx:H film is fitted with both Gaussian (integrated intensity...
-
Reliability and Validity of Optoelectronic Method for Biophotonical Measurements
PublikacjaReliability and validity of measurements is of utmost importance when assessing measuring capability of instruments developed for research. In order to perform an experiment which is legitimate, used instruments must be both reliable and valid. Reliability estimates the degree of precision of measurement, the extent to which a measurement is internally consistent. Validity is the usefulness of an instrument to perform accurate...
-
Realizacja samo-testowania części analogowych elektronicznych syste-mów wbudowanych z wykorzystaniem mikrokontrolerów rodziny XMEGA A
PublikacjaPrzedstawiono mikrosystem pomiarowy zbudowany z zasobów sprzętowych mikrokontrolera ATXmega32A4 pełniący funkcję układu testera wbudowanego przeznaczonego do samotestowania części analogowych elektronicznych systemów wbudowanych. Samotestowanie opiera się na metodzie diagnostycznej, w której układ badany pobudzany jest impulsem prostokątnym, a jego odpowiedź czasowa próbkowana przez przetwornik A/C mikro-kontrolera. Licznik mikrokontrolera...
-
Pomiar kąta zwilżania z wykorzystaniem regresji gaussowskiej
PublikacjaKat zwilżania stanowi wielkość fizyczną umożliwiającą ocenę wielu parametrów charakteryzujących ciecze i ciała stałe o płaskich powierzchniach. W pracy zaprezentowano metodę wyznaczania kąta zwilżania na podstawie analizy cyfrowego obrazu kropli cieczy. Do obliczenia katą zwilżania wykorzystano algorytm regresji gaussowskiej. Umożliwia on ocenę kata miedzy dwiema powierzchniami, bez konieczności reprezentowania ich za pomocą funkcji o...
-
Podejście samotestowania części analogowych elektronicznych systemów wbudowanych z wykorzystaniem mikrokontrolerów rodziny XMEGA A
Publikacja..
-
Photovoltaic demonstration set up
PublikacjaThe use of photovoltaics is growing rapidly in the industry as well as households. Therefore, educating the public will help them understand solar cell technology, which is becoming more common in everyday life. This paper proposes a demonstrational set-up of photovoltaic panel for the purpose of science education. It was used in numerous outreach activities such as science fairs. Moreover, it proved to be a great tool for education...
-
Optimization of a Fabry-Perot Sensing Interferometer design for an optical fiber sensor of hematocrit level
PublikacjaContinuous measurement of the hemato crit level in blo o d can p otentially b e p erformed using optical bre sensors. The FabryPerot interferometric sensors are a promising candidate in this application. The most imp ortant step in the design of the sensor is design of the sensing interferometer. Adequate cavity length and high interference contrast are two most imp ortant requirements in this application. The design metho d of...
-
Nucleation and growth of CVD diamond on fused silica optical fibres with titanium dioxide interlayer
PublikacjaNucleation and growth processes of thin diamond films on fused silica optical fibres have been investigated. Fibres were coated with diamond film using microwave plasma enhanced chemical vapour deposition (µPE CVD) system. Since the growth of diamond on the fused silica glass requires high seeding density, two types of glass pre-treatment were applied: titanium dioxide (TiO2) interlayer deposition and sonication in nanodiamond...
-
Miniaturized impedance analyzer using AD5933
PublikacjaThe paper presents the analyzer allowing to measure impedance in a range of 10 ohms <|Zx|<10 Gohms in a wide frequency range from 10 mHz up to 100 kHz. The device specific features are: miniaturization, low power consumptions and the use of impedance measurement method based on DSP. These features were possible thanks to the use of newest generation of large scale integration chips: e.g. „system on a chip” microsystems (AD5933)...
-
Metody usuwania zakłóceń podczas pomiarów polowych widm Ramana
PublikacjaW pracy zostały scharakteryzowane źródła zakłóceń występujące podczas pomiarów widm Ramana w warunkach polowych. Zaprezentowano wpływ czasu integracji na jakość rejestrowanych widm w przypadkach, gdy szumy własne spektrometru mają składową typu 1/f, dominującą w zakresie małych częstotliwości. Przedstawiono także wyniki uzyskane podczas pomiarów z detekcją synchroniczną, stosowaną w przenośnych spektrometrach Ramana, w pomiarach...
-
Metody usuwania zakłóceń podczas pomiarów polowych widm Ramana
PublikacjaW pracy zostały scharakteryzowane źródła zakłóceń występujące podczas pomiarów widm Ramana w warunkach polowych oraz sposoby redukcji ich wpływu na jakość rejestrowanych widm. Zaprezentowano wpływ czasu integracji na jakość rejestrowanych widm w przypadkach, gdy szumy własne spektrometru mają składową typu 1/f, dominującą w zakresie małych częstotliwości. Przedstawiono także wyniki uzyskane podczas pomiarów z detekcją synchroniczną,...
-
Metody matematyczne syntezowania źródeł optycznych do interferometrów niskokoherentnych dla zastosowa biomedycznych
PublikacjaW pracy przedstawiono mozliwosci wykorzystania metod matematycznych w układach interferometrii niskokoherentnej do zastosowan biomedycznych. Metody takie sa wykorzystywane na kazdym z etapów realizacji układów: projektowania poszczególnych elementów, obróbki danych pomiarowych oraz w trakcie walidacji techniki pomiarowej. W pracy przedstawiono mozliwosci optymalizacji parametrów metrologicznych interferometrów niskokoherentnych...
-
Metody badania właściwości szumowych elementów mocy z SIC
Publikacja..
-
Metody badania właściwości szumowych elementów mocy z SiC
PublikacjaW artykule przedstawiono metody i układy pomiarowe do pomiarów szumów z zakresu małych częstotliwości diod mocy wykonanych z węglika krzemu. Pomiary prowadzone były przy polaryzacji badanych elementów w kierunku przewodzenia i zaporowym. Opracowano układ automatycznej kompensacji składowej stałoprądowej, który umożliwia obserwację i rejestrację szumów wybuchowych.
-
Metody analizy ryzyka podejmowania błędnych decyzji z powodu niepewności pomiarów
PublikacjaReferat dotyczy sposobów definiowania ryzyka podejmowania błędnych decyzji z powodu niepewności pomiarów oraz metod jego obliczania. Usystematyzowano rodzaje prawdopodobieństw łącznych i warunkowych stosowanych jako miary ryzyka w kontekście procesów produkcyjnych. Dokonano przeglądu metod obliczania ryzyka, ze szczególnym uwzględnieniem metod Bayesowskich. Zwrócono uwagę na różnice w stosowanych probabilistycznych modelach pomiaru...
-
Measurements of Spectral Spatial Distribution of Scattering Materials for Rear Projection Screens used in Virtual Reality Systems
PublikacjaRapid development of computing and visualisation systems has resulted in an unprecedented capability to display, in real time, realistic computer-generated worlds. Advanced techniques, including three-dimensional (3D) projection, supplemented by multi-channel surround sound, create immersive environments whose applications range from entertainment to military to scientific. One of the most advanced virtual reality systems are CAVE-type...
-
Measurement system for nonlinear surface spectroscopy by atomic force microscopy for corrosion processes monitoring
PublikacjaIn addition to traditional imaging the surface, atomic force microscopy (AFM) enables wide variety of additional measurements. One of them is higher harmonic imaging. In tapping mode the nonlinear contact between tip and specimen results in higher frequency vibrations. More information available from the higher harmonics analysis proves to be helpful for more detailed imaging. Such visualization is especially useful for heterogeneous...
-
Measurement of complex refractive index of human blood by low-coherence interferometry
PublikacjaIn this article, the usefulness of the optical technique for measurements of blood complex refractive index has been examined. Measurement of optical properties of human blood is difficult to perform because of its nonuniform nature. However, results of my investigation have shown the usefulness of low-coherencei nterferometry for measurement complex refractive index of human blood. Furthermore, mathematical analysis of spectrum...
-
LZWP, czyli jak zbudować CAVE
PublikacjaReferat prezentuje wyniki prac autorów dotyczących specyfikacji technicznej instalacji typu CAVE tworzonej na Wydziale ETI Politechniki Gdańskiej. Przedstawiona analiza została dokonana na pod-stawie wiedzy autorów, studiów literaturowych, wizytacji wybranych instalacji w kraju i zagranicą oraz konsultacji z firmami będącymi wiodącymi producentami lub integratorami systemów 3D.
-
Low voltage photovoltaic power system
PublikacjaThe use of photovoltaics is growing rapidly in the industry as well as households. Therefore, educating the public will help them understand solar cell technology, which is becoming more common in everyday life. This paper proposes a demonstrational set-up of photovoltaic panel for the purpose of science education. It was used in numerous outreach activities such as science fairs. Moreover, it proved to be a great tool for education...
-
Laser reflectance interferometry system with a 405 nm laser diode for in-situ measurement of CVD diamond thickness
PublikacjaIn situ monitoring of the thickness of thin diamond films during technological processes is important because it allows better control of deposition time and deeper understanding of deposition kinetics. One of the widely used techniques is laser reflectance interferometry (LRI) which enables non-contact measurement during CVD deposition. The authors have built a novel LRI system with a 405 nm laser diode which achieves better...
-
In-situ optical diagnostics of boron-doped diamond films growth
PublikacjaInterferometry is a desirable method for in-situ measurement of thin, dielectric film growth, as it don't modify conditions of film deposition. Here we present interferometrical measurements of thickness of doped diamond films during Chemical Vapor Deposition (CVD) process. For this purpose we used a semiconductor laser with a 405nm wavelength. Additional ex-situ measurement using spectral interferometry and ellipsometry...
-
Influence of the boron doping level on the electrochemical oxidation of the azo dyes at Si/BDD thin film electrodes
PublikacjaIn this study the efficiency of electrochemical oxidation of aromatic pollutants, such as reactive dyes, at boron-doped diamond on silicon (Si/BDD) electrodes was investigated. The level of [B]/[C] ratio which is effective for the degradation and mineralization of selected aromatic pollutants, and the impact of [B]/[C] ratio on the crystalline structure, layer conductivity and relative sp3/sp2 coefficient of a BDD electrode were...
-
Fast High-Impedance Spectroscopy Method Using SINC Signal Excitation
PublikacjaIn this paper the method of fast impedance spectroscopy of technical objects with high impedance (|Zx| > 1 Gohm) is evaluated by means of simulation and practical experiment. The method is based on excitation of an object with a sinc signal and sampling response signals proportional to current flowing through and voltage across the measured impedance. The object impedance spectrum is obtained with use of continuous Fourier transform...
-
Enhancing capabilities of Atomic Force Microscopy by tip motion harmonics analysis
PublikacjaMotion of a tip used in an atomic force microscope can be described by the Lennard-Jones potential, approximated by the van der Waals force in a long-range interaction. Here we present a general framework of approximation of the tip motion by adding three terms of Taylor series what results in non-zero harmonics in an output signal. We have worked out a measurement system which allows recording of an excitation tip signal and its...
-
Electrochemical oxidation of sulphamerazine at boron-doped diamond electrodes: Influence of boron concentration
PublikacjaThe boron-doped diamond (BDD) electrodes with different boron concentrations have been tested as electrode material for sulphamerazine (SRM) oxidation in water solution. An investigation of the electrode morphology and molecular structure was carried out using high resolution scanning electron microscopy (SEM) and Raman spectroscopy. Electrochemical results showed clearly that the kinetics and efficiency of SRM oxidation were dependent...
-
Dedicated power supply subsystem for ultra-low noise preamplifiers
PublikacjaIn field of electronics there is need for low-noise amplifiers. Noise have the most important influence on analog circuits. Therefore exist necessity to develop new ultra-low noise power supplies, which can cooperate with specified amplifiers and preamplifiers. It is very common that professional power supplies are very expensive and still have disadvantages. This paper proposes simple and inexpensive solution, which fulfill specific...
-
Atomic Force Microscope data post-processing algorithm for higher harmonics imaging
PublikacjaPrevious works have proved that higher harmonics topography imaging using atomic force microscope (AFM) can significantly enhanced its measurement capabilities. Integrated tools dedicated to most of microscopes allow to visualize the investigated surface only by one selected harmonic. Because of the different characteristics of a sample, scanning tip and the environment, appropriate harmonic selection is time consuming and requires...
-
Application of infrared thermoography to non-contact testing of varistors
PublikacjaTesting of varistors using thermography was carried out in order to assess their protective properties against possible overvoltage phenomena in the form of high-level voltage surges. An advantage of the thermography technique is non-contact temperature measurement. It was proposed to assess the properties of varistors workingin electronic devices as protective elements, on the basis of estimating temperature increments on varist...
-
Amperometric sensing of chemical oxygen demand at glassy carbon and silicon electrodes modified with boron-doped diamond
Publikacja.A boron-doped diamond (BDD) sensor is proposed for effective detection of chemical oxygen demand (COD) by means of amperometric technique. Boron-doped diamond thin films, acting as active sensors, were deposited on both silicon wafer and glassy carbon (GC) substrates by microwave plasma assisted chemical vapour deposition. SEM micrographs showed that BDD–Si displays triangle-faceted crystallites ca. 0.5–3 μm in size, while BDD–GC...
-
Algorytmy przetwarzania widm Ramana podczas detekcji substancji chemicznych
PublikacjaW pracy zostaną przedstawione algorytmy wstępnego przetwarzania widm mające na celu usunięcie lub zmniejszenie intensywności zakłóceń obecnych w rejestrowanych widmach Ramana, ze szczególnym uwzględnieniem automatyzacji tego procesu (bez konieczności wyboru parametrów przetwarzania przez obsługę urządzenia). Kolejną prezentowaną grupę algorytmów stanowią procedury parametryzacji widm, które opisują widma w postaci zbioru kilku...
-
A solution of the integrated µBIST for functional and diagnostic testing in mixed-signal electronic embedded systems
PublikacjaMain problem of the paper is testing of analog circuits and blocks in mixed-signal electronic embedded systems (EESs), using the built-in self-test (BIST) technique. The integrated mBIST based on reusing signal blocks already present in an EES, such as processors, memories, ADCs, is presented. The novelty of the solution is the extended functionality of the mBIST. It can perform 2 testing functions: functional testing and fault...
-
A measurement system for nonlinear surface spectroscopy with an atomic force microscope during corrosion process monitoring
PublikacjaIn addition to traditional imaging the surface, atomic force microscopy (AFM) enables wide variety of additional measurements. One of them is higher harmonic imaging. In tapping mode the nonlinear contact between tip and specimen results in higher frequency vibrations. More information available from the higher harmonics analysis proves to be helpful for more detailed imaging. Such visualization is espe-cially useful for heterogeneous...
-
A family of new generation miniaturized impedance analyzers for technical object diagnostics
PublikacjaThe paper presents the family of three analyzers allowing to measure impedance in range of 10 ohm<|Zx|<10 Gohm in a wide frequency range from 10 mHz up to 100 kHz. The most important features of the analyzers family are: miniaturization, low power consumption, low production cost, telemetric controlling and the use of impedance measurement method based on digital signal processing DSP. The miniaturization and other above mentioned...
Rok 2012
-
Wireless data transmission for fiber optical sensor system
PublikacjaW artykule opisano możliwość wykorzystania bezprzewodowego systemu transmisji danych do transmisji sygnałów z czujników światłowodowych.
-
RAMAN DIAGNOSTICS OF CVD DIAMOND GROWTH
PublikacjaDevelopment of Raman spectroscopic system for diagnostics of growth of diamond and BDD (Boron- Doped-Diamond) thin films during μPA CVD (Microwave Plasma Assisted Chemical Vapour Deposition) process is described. Raman studies of such films were carried out as in-situ monitoring of film deposition as ex-situ measurements conducted for a sample outside the reaction vessel after manufacturing process. Modular system for the in-situ...
-
Determination of Chemical Oxygen Demand (COD) at Boron-doped Diamond (BDD) Sensor by Means of Amperometric Technique
PublikacjaA boron-doped diamond (BDD) sensor was proposed for effective detection of chemical oxygen demand (COD) by means of amperometric technique. Thin boron doped diamond active sensor layer was deposited on Si wafer and glassy carbon substrate by Microwave Plasma Enhanced Chemical Vapor Deposition (MW PE CVD). The structure of BDD was confirmed by Raman spectra analysis. Broad Raman bands centered at 482 cm-1 and 1219 cm-1 are typical...
-
Application of wavelength division multiplexing in sensor networks
PublikacjaOver the past few years the need to acquire data on various parameters from a number of sensors grew. The need that led to the development of a network of sensors which enables simultaneous control and measurement in a wide range of applications. The aim of this article is to discuss a possibility of connecting a variety of sensors in a network that would utilize WDM technology. Wavelength Division Multiplexing is commonly used...
-
A complete impedance analysis of electrochemical cells used as energy sources
PublikacjaA comprehensive description of impedance ofelectrochemical systems has been presented, along withthe assumptions of the method used. In this method, amultisinusoidal current excitation signal is used. Thechanges of potential of both the electrodes and thepotential difference between these electrodes are allregistered simultaneously as a function of time. Theproposed method offers the possibility of separatelydetermining the instantaneous...
Rok 2010
-
BUDOWA I OPROGRAMOWANIE PRZENOŚNEGO SPEKTROMETRU RAMANA
PublikacjaW pracy przedstawiono budowę oraz zasadę działania przenośnego spektrometru Ramana, przygotowywanego w Katedrze Optoelektroniki i Systemów Elektronicznych Politechniki Gdańskiej. Opisano format plików *.SPC, który jest wykorzystywany przez oprogramowanie sterujące budowanym spektrometrem oraz stosowany przez większość komercyjnych aplikacji przeznaczonych do analizy widm Ramana. Przedstawiono podstawowe metody parametryzacji rejestrowanych...
Rok 2009
-
An application of the TCRBF neural network in multi-node fault diagnosis method
PublikacjaPrzedstawiono nową metodę samo-testowania części analogowej w systemach elektronicznych sterowanych mikrokontrolerami. Układ badany pobudzany jest przebiegiem sinusoidalnym przez generator zamontowany w systemie, a jego odpowiedź jest próbkowana w wybranych węzłach przez wewnętrzny przetwornik A/C mikrokontrolera. Detekcja i lokalizacja uszkodzenia jest dokontwana przez sieć neuronową typu TCRBF. Procedurę diagnostyczną zaimplementowano...
Rok 2006
-
On-Board Detection, Classification and Evaluation of Nonlinearities
PublikacjaArtykuł prezentuje tester wbudowany BIT przeznaczony do wydobywania informacji diagnostycznej z sygnału generowanego przy zastosowaniu oscylacyjnej metody testowania. Układ bazujący na technice modulacji Sigma-Delta i sztucznych sieciach neuronowych może wykrywać nieliniowość w sygnale testującym, określać rodzaj nieliniowości i szacować zawartość harmonicznych.
Rok 2004
-
Zastosowanie oprogramowania COMSIS do oceny dynamicznej odporności na zakłócenia cyfrowych układów kombinacyjnych.
PublikacjaWyniki badania odporności układów cyfrowych na zakłócenie dynamiczne w istotny sposób zależą od parametrów sygnału stymulującego. Proponowana metodyka zakłada pobudzanie badanego układu sygnałem szumu białego o określonej szerokości pasma częstotliwości. Badania symulacyjne z modelem układu progowego oraz szybkiego komparatora z histerezą przeprowadzono w środowisku COMSIS. Uzyskane wyniki potwierdzają, że im węższe pasmo szumu...
-
Pomiary grubości cienkich warstw metodą modulacji chromatycznej.
PublikacjaTematem artykułu jest pomiar grubości struktur cienkowarstwowych szerokostosowanych w optoelektronice, transparentnych warstw dielektrycznych. Grubość jest najistotniejszym parametrem warstwy i determinuje jej właściwościoptyczne. Metoda pomiaru grubości cienkich warstw powinna być bezkontaktowa, nieniszcząca, niekosztowna oraz odporna na zakłócenia
-
Pomiarowo-kontrolny system zastosowany w procesie produkcji central do systemów alarmowych.
PublikacjaPrzedstawiono strukturę funkcjonalną systemu pomiarowo-kontrolnego zastosowanego w procesie produkcji central do systemów alarmowych. Opisano szerzej stanowisko pomiarowo-kontrolne które zostało zastosowane w systemie obiegu informacji w procesie wytwarzania urządzen alarmowych.
-
Effect of illumination on noise of silicon solar cells
PublikacjaTransport and noise properties of silicon solar cells in darkness and under illumination have been studied. The measurements were carried out for both reverse and forward bias of the device. The changes in the sample behaviour are due to the variation of PN junction dynamic resistance and, also, the occurence of both 1/f and generation-recombination noise components
-
Analog fault signature based on sigma-delta modulation and oscillation-test methodology.
PublikacjaW artykule dokonano przeglądu prac z zakresu testowania układów elektronicznych metodą oscylacyjną. Wskazując na niedostatki aktualnie stosowanej techniki testowania oscylacyjnego zaproponowano nową sygnaturę uszkodzeń dla układów analogowych. Proponowany parametr diagnostyczny jest wydobywany z odpowiedzi czasowej oscylatora testującego, w układzie złożonym z detektora szczytowego, modulatora sigma-delta oraz licznika rewersyjnego....
-
Akwizycja i przetwarzanie danych w systemie telemonitoringu sieci ciepłowniczej. II Krajowa Konferencja.
Publikacja.
Rok 2003
-
Zastosowanie zintegrowanych środowisk programistycznych w laboratorium organizacji systemów pomiarowych.
PublikacjaArtykuł przedstawia opracowane i zrealizowane w 2002 roku w Katedrze Miernictwa Elektronicznego laboratorium Interfejsy i Organizacja Systemów Elektronicznych. Zaprezentowano ogólną koncepcję laboratorium, polegającą na wstępnym przeszkoleniu ze środowiska programistycznego, a następnie łączeniu w ramach dalszych ćwiczeń zadań wprowadzających (odtwórczych) i zadań projektowych. Opisano korzyści płynące z zastosowania zintegrowanego...