Wyszukiwarka
Zakład Ekoinżynierii i Silników Spalinowych
Publikacje
Filtry
wszystkich: 301
Katalog Publikacji
Rok 2024
-
Experimental investigation of thermal energy storage in shell-and-multi-tube unit with nano-enhanced phase change material
PublikacjaThis paper deals with thermal energy storage with use of nanoparticle enhanced phase change material in shell-and-multitube unit. The experiments are conducted under atmospheric pressure. Paraffin wax and two different fatty acids are used as base phase change material. Graphite and multi-walled carbon nanotubes serve as nanoparticles. Graphite nanoparticles are tested at the concentrations of 0.1%, 1% and 5% by weight, while multi-walled...
Rok 2022
-
Numerical Modelling of Forced Convection of Nanofluids in Smooth, Round Tubes: A Review
PublikacjaA comprehensive review of published works dealing with numerical modelling of forced convection heat transfer and hydrodynamics of nanofluids is presented. Due to the extensive literature, the review is limited to straight, smooth, circular tubes, as this is the basic geometry in shell-and-tube exchangers. Works on numerical modelling of forced convection in tubes are presented chronologically in the first part of the article....
-
Stability investigation of the PCM nanocomposites
PublikacjaIn present study was showed the results of research the stability of nanoPCMs in terms of types and concentrations of surfactant used. For stearic acid has been added PVP or oleic acid in concentrations of 0%, 5% and 10%. Nanoparticles TiO2 and Al-2O3 in concentration of 1% were chosen to be researched in this test. The mixing of nanocomposites has been done in an ultrasonic scrubber in which the samples were placed for 45 mins....
-
Stirling engines - the state of technology development and computational models
PublikacjaStirling engines represent a technologically important solution in combined heat and power systems. Their use enables the achievement of over 90 percent efficiency in the management of the primary energy source with a very high durability of the device, mainly due to the lack of contact of the working gas with external factors and a very small number of mechanical components. The use of a Stirling engine may be equally important...
Rok 2021
-
Efektywność energetyczna systemów chłodniczych pracujących z dwutlenkiem węgla jako czynnikiem roboczym
PublikacjaArtykuł dotyczy zagadnienia efektywności energetycznej układów chłodniczych pracujących z dwutlenkiem węgla jako czynnikiem roboczym. W celu szczegółowego przeanalizowania potencjału zastosowania dwutlenku węgla, jako czynnika roboczego w urządzeniach chłodniczych, przeprowadzone zostały obliczenia dla kilku modeli układów chłodniczych. Do przeprowadzenia analizy wybrano trzy układy chłodnicze, tj. układ transkrytyczny, układ kaskadowy...
-
Effect of Temperature and Nanoparticle Concentration on Free Convective Heat Transfer of Nanofluids
PublikacjaA theoretical analysis of the influence of temperature and nanoparticle concentration on free convection heat transfer from a horizontal tube immersed in an unbounded nanofluid was presented. The Nusselt (Nu) number and heat transfer coefficient were parameters of the intensity of the convective heat transfer. For free convection, the Nu number was a function of the Rayleigh (Ra) number and Prandtl (Pr) number. The Rayleigh (Ra)...
-
Experimental Investigation of Free Convection Heat Transfer from Horizontal Cylinder to Nanofluids
PublikacjaThe results of free convection heat transfer investigation from a horizontal, uniformly heated tube immersed in a nanofluid are presented. Experiments were performed with five base fluids, i.e., ethylene glycol (EG), distilled water (W) and the mixtures of EG and water with the ratios of 60/40, 50/50, 40/60 by volume, so the Rayleigh (Ra) number range was 3 104 Ra 1.3 106 and the Prandtl (Pr) number varied from 4.4 to 176....
-
Free Convection Heat Transfer from Horizontal Cylinders
PublikacjaThe results of experimental investigation of free convection heat transfer in a rectangular container are presented. The ability of the commonly accepted correlation equations to reproduce present experimental data was tested as well. It was assumed that the examined geometry fulfils the requirement of no-interaction between heated cylinder and bounded surfaces. In order to check this assumption recently published correlation equations...
-
Modular Approach for Modelling Warming Up Process in Water Installations with Flow-Regulating Elements
PublikacjaThe paper presents a new method for modelling the warming up process of a water system with elements regulating the flow in a stochastic manner. The paper presents the basic equations describing the work of typical elements which the water installation is composed of. In the proposed method, a new computational algorithm was used in the form of an iterative procedure enabling the use of boundary conditions that can be stochastically...
-
Numerical simulation of natural convection of Glycol-Al2O3 nanofluids from a horizontal cylinder
PublikacjaThis paper deals with natural convection around a circular cylinder with constant heat flux in a cavity using computational fluid dynamics. As fluids ethylene glycol and a mixture of ethylene glycol with Al2O3 nanoparticles (mass concentrations of nanoparticles: 0.1% and 1%) are chosen. Rayleigh number ranges from 3104 to 3105. The nanofluids are modeled with single-phase approach. For the investigated range of nanoparticle concentration, the...
-
Opłacalność zastosowania pompy ciepła w układach centralnego ogrzewania i ciepłej wody użytkowej
PublikacjaW artykule przedstawiono problem opłacalności ekonomicznej stosowania pompy ciepła, w układach ciepłej wody użytkowej oraz centralnego ogrzewania. Zasadność zastosowania takich źródeł ciepła w tych instalacjach spowodowana jest ogólnoświatowymi kierunkami i stopniowym odchodzeniem od konwencjonalnych źródeł energii takich jak kotły olejowe lub gazowe. Przedmiotem artykułu był budynek jednorodzinny o powierzchni użytkowej ok. 145...
-
Wpływ właściwości czynnika roboczego na eksploatację wybranych systemów chłodniczych
PublikacjaW artykule przedstawiono wpływ wyboru czynnika roboczego na eksploatację teoretycznego systemu chłodniczego. Niniejszą analizę przeprowadzono dla trzech układów chłodniczych, które na potrzeby prowadzonej analizy sklasyfikowano jako: grupa domowa, grupa przemysłowa i grupa specjalna. Przyjętymi urządzeniami są: w grupie domowej – klimatyzator typu powietrze-powietrze, w grupie przemysłowej – chłodnia statku do transportu żywności...
Rok 2020
-
A Comparison of Empirical Correlations of Viscosity and Thermal Conductivity of Water-Ethylene Glycol-Al2O3 Nanofluids
PublikacjaBecause of their superb thermal conductivity, nanofluids are seen as new generation of cooling mediums in many engineering applications. It is well established that even a small amount of nanoparticles mixed with a base fluid may result in distinct thermal conductivity enhancement. On the other hand, addition of nanoparticles to the base fluid results in its substantial viscosity increase. Therefore, it is very dicult to evaluate...
-
A Theoretical and Experimental Study of Moderate Temperature Alfa Type Stirling Engines
PublikacjaThe Stirling engine is a device that allows conversion of thermal energy into mechanical energy with relatively high efficiency. Existing commercial designs are mainly based on the usage of high temperature heat sources, whose availability from renewable or waste heat sources is significantly lower than that of moderate temperature sources. The paper presents the results of experimental research on a prototype alpha type Stirling...
-
Analiza modeli opisujących wrzenie w przepływie w kanałach konwencjonalnych
PublikacjaW artykule przedstawiona została analiza wybranych korelacji pozwalających na wyznaczenie współczynników przejmowania ciepła podczas wrzenia w przepływie, które przeznaczone są dla kanałów o średnicach konwencjonalnych. Przedstawiona w pracy analiza została wykonana na podstawie badań eksperymentalnych dostępnych w literaturze, które prowadzone były dla pełnego zakresu zmiany stopnia suchości oraz stosunkowo szerokiego zakresu...
-
Analiza procesów cieplnych zachodzących w skraplaczu płaszczowo-rurowym
PublikacjaW artykule przedstawiony został algorytm obliczeń cieplnych skraplacza płaszczowo- rurowego. Ten wymiennik ciepła wpływa na efektywność działania całego układu, w którym jest zastosowany. Z tego powodu, dobór odpowiedniego wymiennika do całej instalacji nie jest prosty i jest ściśle związany z szeregiem założeń projektowych, które znacząco wpływają na poprawną pracę urządzenia oraz całej instalacji. Prawidłowe określenie współczynników...
-
Application of Stirling Engine Type Alpha Powered by the Recovery Energy on Vessels
PublikacjaThe Stirling engine is a device, in which thermal energy is transformed into mechanical without a contact between the heat carrier, and the working gas closed in the engine. Mentioned feature makes this type of engine very attractive for the use of the recovery energy, taken from other heat devices. One of the potential applications of Stirling engines is the use of thermal energy generated in the ship's engine room for producing...
-
ECU calibration for gaseous dual fuel supply system in compression ignition engines
PublikacjaThe dual fuel (DF) combustion mode is proven solution that allows to improve or get at the same level engine performance and reduce toxic compounds in exhaust gases which is confirmed by researchers and end-users. DF combustion mode uses two fuels gaseous fuel as a primary energy source and a pilot quantity of diesel fuel as ignition source. However, in order, to fully take advantage of the potential of the dual fuel mode, DF system...
-
Wodór jako paliwo cz. 1
PublikacjaW artykule przedstawiono wodór jako nowoczesny nośnik energii oraz jego zastosowanie techniczne w ujęciu konwersji energii. Przybliżono jego odkrycie, właściwości oraz jego wykorzystanie od odkrycia do współczesności. Dokonano opisu budowy i zasady działania ogniw paliwowych. Omówiono ich podział przedstawiając zalety i wady każdego rozwiązania oraz ich zastosowanie techniczne w zależności od typu ogniwa.
-
Wodór jako paliwo cz. 2
PublikacjaW artykule scharakteryzowano aktualne i przyszłościowe metody wytwarzania wodoru. Przedstawiono problem związany z przechowywaniem wodoru oraz ukazano aktualne i przyszłościowe rozwiązania dotyczące magazynowania wodoru.
-
Zintegrowany Program Rozwoju Politechniki Gdańskiej – Moduł 1. Poprawa jakości kształcenia na studiach stacjonarnych II stopnia
PublikacjaPolitechnika Gdańska realizuje od 1 kwietnia 2018 roku projekt „Zintegrowany Program Rozwoju Politechniki Gdańskiej” (POWER 3.5) dofinansowywany ze środków Unii Europejskiej z Europejskiego Funduszu Społecznego w ramach Programu Operacyjnego „Wiedza Edukacja Rozwój”. W artykule zostały przedstawione informacje dotyczące realizacji zadań szczegółowych modułu 1, będącego pierwszym zadaniem z trzech określonych w projekcie. Artykuł...
Rok 2019
-
A semi-empirical model for flow boiling heat transfer with account of the reduced pressure effect
PublikacjaIn the present study the attention was focused on the influence of reduced pressure on the predictions of heat transfer during flow boiling at the extensive range of pressures. The results of calculations were to test the sensitivity of the in-house flow boiling model with respect to the selection of the appropriate two-phase flow multiplier, which is one of the distinctive elements of that model. For this purpose a few two-phase...
-
A unified approach to the analysis of electric energy and fuel consumption of cars in city traffic
PublikacjaForecasting fuel and electricity consumption is an important factor determining the direction of changes in road engineering solutions, traffic management, selection of routes for public transport and development more efficient car drive systems. With a reliable and easy-to-use computational tool, it is possible to reduce the consumption of primary energy sources and reduce the emission of toxic compounds in cities. An analysis...
-
An improved method for flow boiling heat transfer with account of the reduced pressure effect
PublikacjaIn the paper are presented the results using the authors own model to predict heat transfer coefficient during flow boiling. The model has been tested against a large selection of experimental data to investigate the sensitivity of the in-house developed model. In the work are presented the results of calculations obtained using the semi-empirical model on selected experimental flow boiling data of the refrigerants: R134a, R1234yf,...
-
Analysis of start energy of Stirling engine type alpha
PublikacjaThe Stirling engine type alpha is composed of two cylinders (expansion space E and compression space C), regenerator that forms the space between the cylinders and the buffer space (under the pistons). Before the start-up and as a result of long-term operation, the average pressure in the working space (above the pistons) and in the buffer space is the same. However, in the initial phase of operation, the average pressure in the...
-
Analysis of the regenerative braking process for the urban traffic conditions
PublikacjaIn a regular drive system, with an internal combustion engine, vehicle braking is connected with the unproductive dissipation of kinetic and potential energy accumulated in the mass of the vehicle into the environment. This energy can constitute up to 70% of the energy used to drive a vehicle under urban conditions. Its recovery and reuse is one of the basic advantages of hybrid and electric vehicles. Modern traffic management...
-
Application of nanofluids in thermal technologies
PublikacjaNanofluids it is a relatively new category of thermal fluids that can serve as coolants, both in single- and two phase systems. However application of nanofluids in industrial applications requires faultless their thermophysical properties. Existing models originally developed for liquid/solid particles mixtures (slurries) fail in case of nanofluids. Moreover correlations used to calcuate heat transfer coefficients of conventional...
-
DME as alternative fuel for compression ignition engines – a review
PublikacjaThe ecological issues and the depletion of crude oil, has led the researchers to seeking for non-petroleum based alternative fuels, along with more advanced combustion technologies, and after-treatment systems. The use of clean alternative fuels is the one of the most perspective method that aiming at resolving of the said issues. One of the promising alternative fuels that can be used as a clean highefficiency compression ignition...
-
Experimental study and comparison with predictive methods for flow boiling heat transfer coefficient of HFE7000
PublikacjaThis article describes an experimental study of flow boiling of HFE7000 inside a smooth vertical channel. The investigation has been carried out in a circular stainless-steel tube with an inner diameter of 2.3 mm. The data have been collected for the applied heat fluxes q ranging from 61 to 205 kW/m2, the mass flux G ranging from 214 to 1006 kg/(m2 s), the saturation temperature Tsat ranging from 30 to 54 °C and the full range...
-
Heavy Duty Vehicle Fuel Consumption Modelling Based on Exploitation Data by Using Artificial Neural Networks
PublikacjaOne of the ways to improve the fuel economy of heavy duty trucks is to operate the combustion engine in its most efficient operating points. To do that, a mathematical model of the engine is required, which shows the relations between engine speed, torque and fuel consumption in transient states. In this paper, easy accessible exploitation data collected via CAN bus of the heavy duty truck were used to obtain a model of a diesel...
-
Hydraulic resistance analyses of selected elements of the prototype Stirling engine
PublikacjaThe paper presents the results of simulation tests of hydraulic resistance and temperature distribution of the prototype Stirling alpha engine supplied with waste heat. The following elements were analyzed: heater, regenerator and cooler. The engine uses compressed air as a working gas. Analyses were carried out for three working pressure values and different engine speeds. The work was carried out in order to optimize the configuration...
-
Modeling of the internal combustion engine cooling system
PublikacjaThe article concerns computer modelling of processes in cooling systems of internal combustion engines. Modelling objectives and existing commercial programs are presented. It also describes Author’s own method of binding graphs used to describe phenomena in the cooling system of a spark ignition engine. The own model has been verified by tests on the engine dynamometer. An example of using a commercial program for experimental...
-
The impact of environmentally friendly refrigerants on heat pump efficiency
PublikacjaThis paper discusses the issue of heat pump simulation. Lower operating costs can be achieved through good equipment design and appropriate operation. Detailed technical and economic analysis inform the selection of system components with the highest possible efficiency and lower energy demand. The use of systems based on environmentally friendly refrigerants can deliver long product life, which is associated with a shorter payback...
-
Thermodynamic modeling of combustion process of the internal combustion engines – an overview
PublikacjaThe mathematical description of combustion process in the internal combustion engines is a very difficult task, due to the variety of phenomena that occurring in the engine from the moment when the fuel-air mixture ignites up to the moment when intake and exhaust valves beginning open. Modeling of the combustion process plays an important role in the engine simulation, which allows to predict incylinder pressure during the combustion,...
Rok 2018
-
Comparison of predictive methods for flow boiling heat transfer in conventional channels and minichannels - the effect of reduced pressure
PublikacjaIn the paper are presented the results of follow on studies from [1]–[3] using authors own model to predict heat transfer coefficient during flow boiling. The model has been tested against a large selection of experimental data collected from various researchers to investigate the sensitivity of the in-house developed model. The collected experimental data came from various studies from literature and were conducted for the full...
-
COMPARISON OF PREDICTIVE METHODS FOR FLOW BOILING HEAT TRANSFER IN CONVENTIONAL CHANNELS AND MINICHANNELS – THE EFFECT OF REDUCED PRESSURE
PublikacjaIn the paper are presented the results of follow on studies from [1]–[3] using authors own model to predict heat transfer coefficient during flow boiling. The model has been tested against a large selection of experimental data collected from various researchers to investigate the sensitivity of the in-house developed model. The collected experimental data came from various studies from literature and were conducted for the full...
-
Dobór parametrów platformy załadowczo-rozładunkowej
PublikacjaArtykuł opisuje propozycję zastosowania pneumatycznego mechanizmu napędowego windy załadowczej zasilanej sprężonym powietrzem z układu hamulcowego samochodu ciężarowego. Autorzy starają się określić moc poszczególnych urządzeń napędu. W tym celu wykonano symulację komputerową ruchu platformy windy, na podstawie której określono momenty jakie muszą wytworzyć silniki pneumatyczne. Obliczono czasy opadania i podnoszenia platformy.
-
Dynamic characteristics of the proton exchange membrane fuel cell module
PublikacjaThe paper describes a fuel cell based system and its performance. The system is based on two fuel cell units, DC/DC converter, DC/AC inverter, microprocessor control unit, load unit, bottled hydrogen supply system and a set of measurement instruments. In the study presented in the paper a dynamic response of the proton exchange membrane (PEM) fuel cell system to unit step change load as well as to periodical load changing cycles...
-
Energetic model of hydraulic system of refuse collection vehicle based on simulation and experimental data
PublikacjaThis paper presents an energetic model of hydraulic system of a refuse collection vehicle. First, benefits resulting from implementation of an energetic model in the industry and operation of a Refuse Collection Vehicle are briefly explained. Then, components of the energy consumption in hydraulic circuits of compactor and lifting device are described and combined into a comprehensive model that can be evaluated using basic measurement...
-
Evaluation of the efficiency of the duty cycle of refuse collection vehicle based on real-world data
PublikacjaIn this paper a method of the efficiency evaluation of the duty cycle of Refuse Collection Vehicle is presented. Using real world data, two representative duty cycles were analysed. Total cycle efficiency was calculated, as well as the efficiency of particular cycle phases. Then, energy needed to collect and compact the waste and energy from fuel were compared. Measured and calculated values were shown on the diagrams illustrating...
-
Experimental determination of general characteristic of internal combustion engine using mobile test bench connected via Power Take-Off unit
PublikacjaThe general characteristics of the engine include information about the regions of the engine's operating area that are most efficient, where specific fuel consumption reaches the smallest values. Economic operation based on those characteristics can contribute to a significant reduction of fuel consumption and consequently less pollutant emissions and lower costs. The paper presents an experimental method of determination of general...
-
Experimental investigation of forced convection of water/EGAl2O3 nanofluids inside horizontal tube
PublikacjaIn this paper, forced convection of water/EG-Al2O3 nanofluids inside horizontal stainless steel tube is studied experimentally. As base fluid served water/EG mixture of two ratios (60:50 and 50:50). Nanoparticle mass concentrations was 0.1% or and 1%. Transition and turbulent flow regimes were tested. Average heat transfer coefficient and pressure drop values were determined for nanofluids and compared to base fluids. Deterioration...
-
Experimental investigation of two-phase thermosyphon heat exchanger charged with acetone
PublikacjaThis paper presents thermal characteristics of prototype of a two-phase thermosyphon heat exchanger (TPTHEx) charged with acetone as a working fluid. The TPTHEx consists of two horizontal cylindrical vessels connected by two risers and a downcomer. Tube bundles placed in the lower and upper cylinders work as an evaporator and a condenser, respectively. The tested TPTHEx operates in a vacuum. Therefore, the working liquid is boiled...
-
Modelowanie procesu wrzenia i kondensacji w rozszerzonym zakresie ciśnień zredukowanych
PublikacjaNiniejsza rozprawa doktorska ma na celu pokazanie wpływu uwzględnienia ciśnienia zredukowanego w analizowanym modelu opisują-cym współczynnik przejmowania ciepła na zbieżność z danymi eksperymentalnymi.Przedmiotem analizy jest półempiryczny model Mikielewicza w zastosowaniu do danych eksperymentalnych w kanałach konwencjonalnych i o małej średnicy płynów uznanych za perspektywiczne.W ramach realizowanych prac badawczych pozyskano...
-
Numerical Study of Turbulent Flow and Heat Transfer of Nanofluids in Pipes
PublikacjaIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (Reynolds number between 6000 and 12000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
Performance of the domestic micro ORC equipped with the shell-and-tube condenser with minichannels
PublikacjaIn this paper, the original compact shell-and-tube heat exchanger with circular minichannels of in-house design and manufacturing is presented as the condenser for the domestic micro heat and power plant investigations as well as other future technical applications. The heat exchanger is equipped with turbulizing baffles inside the shell. The shell itself is made of a tubular sleeve having an inner diameter of 0.067 m and the length...
-
Research on the phenomena of warming up and free cooling down the car engine
PublikacjaThe average cold start temperature in Europe is 9 degrees C. However, not the average is the most important for the composition of exhaust gases and associated air pollution. The most onerous for the environment are the winter starts when automotive emissions of harmful gases add up in cities with those of home heating systems. The paper presents preliminary studies of warming up and cooling down processes in various environmental conditions....
-
The effect of reduced pressure on carbon dioxide flow boiling heat transfer in minichannels
Publikacja. In the paper presented are the results of the study on the effect of reduced pressure on flow boiling heat transfer data in minichannels as well as conventional ones. That effect renders that most of heat transfer correlations fail to return appropriate results of predictions. Mostly they have been developed for the reduced pressures from the range 0.1-0.3. The special correction has been postulated to the in-house model of flow...
-
Thermal energy storage using stearic acid as PCM material
PublikacjaThis work presents an experimental study of thermal energy storage by use of PCM. The aim of the study was to establish the influence of different inlet temperature of heat transfer fluid (HTF) and different Reynolds number of HTF on intensity of charging process. The PCM used in this study was stearic acid and water was used as HTF. A copper helical coil mounted in cylindrical container served as a heat transfer surface.
-
WYKORZYSTANIE SILNIKA STIRLINGA DO ODZYSKU ENERGII ZE SPALIN
PublikacjaSilnik Stirlinga jest urządzeniem wytwarzającym energię mechaniczną, w którym nie występuje spalanie paliwa wewnątrz cylindra. Dzięki temu możliwe jest zasilanie silnika energią z dowolnego źródła. Takim źródłem może być promieniowanie słoneczne, spalanie niskokalorycznego paliwa zachodzące w zewnętrznej komorze spalania lub energia odpadowa z innego urządzenia cieplnego, np. silnika spalinowego autobusu lub pojazdu ciężarowego....