Search
Filters
total: 741
filtered: 595
Search results for: SOLID STATE POST-CONDENSATION
-
HILS for the Design of Three-Wheeled Mobile Platform Motion Surveillance System with a Use of Energy Performance Index
PublicationCurrent tendency in mechatronic design requires the use of comprehensive development of an environment, which gives the possibility to prototype, design, simulate and integrate with dedicated hardware. The paper discusses the Hardware-In-the-Loop Simulations (HILS) mechatronic technique, used during the design of the surveillance system based on energy performance index. The presented test configuration (physical controller – emulated...
-
Donor-substituted SrTi1+xO3−δ anodes for SOFC
PublicationNonstoichiometric Nb-substituted SrTiO3 compounds were investigated in order to discuss the influence of nonstoichiometry at the sample properties in the light of recent results reported in the literature. Structural and electrical properties of samples were characterized. Investigated compounds were also applied as anodes for Solid Oxide Fuel Cells and their reactivity with YSZ electrolyte was examined. The defect chemistry explaining...
-
New ceramic materials derived from pyrolyzed poly(1,2-dimethylsilazane) and starch as a potential anode for Li-ion batteries
PublicationNewmaterialswere obtained by pyrolysis of starch (S) and poly(1,2-dimethylsilazane) (PSN) (weight ratio: PSN/S 30/70) at temperature a) 500 °C, b) 700 °C and c) 900 °C. Ceramic materials were characterized by infrared spectroscopy, TGA, Raman spectroscopy and SEM. New Si\O and shifted Si\C stretching vibration modes emerged confirming direct interaction between silicon originating fromsilazane and oxygen coming fromstarch. The...
-
Solid Oxide Fuel Cells with Ni infiltrated perovskite anode
PublicationNiobium-doped strontium titanate was used as the anode for a solid oxide fuel cell. Electrolyte-supported cells were prepared with pure perovskite and composite perovskite–yttria–stabilized-zirconia (YSZ) anodes. Fuel cell tests demonstrated significant improvement in power density after infiltration with a small amount of Ni. The obtained values of power densities are comparable with conventional Ni/YSZ cermet anode. In addition,...
-
Modelling of Geared Multi-Rotor System
PublicationIn the paper the method of modelling a speed-varying geared rotor system is presented. The proposed approach enables us to obtain an accurate low-order lumped parameter representation of the investigated system. The final model consists of reduced modal models of an undamped beam/torsional shaft system as well as a spatially lumped model of other linear and nonlinear phenomena including gear mesh interaction.
-
Multicomponent layers for aluminium alloys surface consolidation
PublicationThe main reason of the surface modification of the components such as pistons and cylinder blocks made of cast aluminium alloys is to obtain high hardness, wear and corrosion resistance of the working surface for larger lifetime of the motor-car and aircraft engines. In that aspect, the new conception of development - by hybrid method - of surface layers containing manganese, nitrogen, sulphur (Mn-N-S) and manganese, nitrogen,...
-
Determination of ability of hydrotronic systems to start in low ambient temperatures
PublicationPrzedstawiono wyniki badań symulacji komputerowej zespołów układów hydrotronicznych w warunkach szoku termicznego. Pokazano metodę określania zdatności hydrotronicznych zespołów i układów podczas rozruchu w warunkach szoku termicznego.
-
High temperature corrosion of evaporator tubes with thermal sprayed coatings
PublicationDegradation examinations of outer surface of low-emission steam boiler evaporator tubes are presented in the paper. Metallographic evaluation of scale morphology, its micro sites chemical composition analysis and distribution of elements on cross sections have been performed. Water-wall tubes were exposed in steam boiler for up to two years period. Common tubes made of 16Mo3 steel suffered sulphide and molten salts corrosions....
-
Monitoring of Velocity of Manufacturing Machines Subassamblieas by Means of a DAQ System
PublicationArtykuł dotyczy dokładnych cyfrowych pomiarów prędkości ruchu podzespołów maszyn, realizowanych za pomocą enkoderów kwadraturowych, kart licznikowych DAQ oraz dedykowanych aplikacji pomiarowych DAQ. Przedstawiono koncepcje trzech różnych sposobów takiego pomiaru. W pierwszym sposobie, nazywanym ''częstotliwościowym'', pomiar odbywa się poprzez bramkowane zliczanie impulsów enkodera. Drugi sposób nazywany ''czasowym'' polega na...
-
Properties of surface layers of duplex stainless steel after burnishing processes
PublicationStress corrosion cracking resistance of cold worked layers of 25 Cr duplex stainless steel grade UR52N+ has been investigated. The surface layers were performed through burnishing treatment. The residual stresses at surface layers were determined using grazing angle incidence X-ray diffraction method (g-sin2 Ψ). Corrosion tests were performed with the use of Slow Strain Rate Test technique in boiling 35% MgCl2 solution. It has...
-
Finishing of Ceramics in a Single-Disk Lapping Machine Configuration
PublicationPrzedstawiono metodę obróbki ceramiki technicznej na zmodifikowanej docierarce jednotarczowej z niezależnym napędem pierścienia prowadzącego. Omówiono przebieg obróbki z wykorzystaniem nowych narzędzi i zastosowaniem ziarna wiązanego.
-
Rigid Finite Element Modeling for Identification of Vibrations in Elastic in Elastic Rod Driven by a DC-motor Suplied from a Thyristor Rectifier
PublicationRozdział dotyczy analizy numerycznej układu elektromechanicznego. Układ składa się z silnika zasilanego z jednopołówkowego prostownika tysystorowego i napędzanego tym silnikiem wirującego pręta. Celem obliczeń jest określenie postaci i wielkości drgań pręta, jeśli uwzględniamy jego elastyczność. Dyskretna struktura modelu to łańcuch wielomasowy ciał - sztywnych ciał połączonych bezmasowymi węzłami. Autorzy obliczyli zachowanie...
-
Cavitation wearing of the SUPERSTON alloy after laser treatment at cryogenic conditions
PublicationThe purpose of this paper is to demonstrate the method of laser remelting at cryogenic conditions of the SUPERSTON alloy and its influence on microstructure and cavitation wearing. The cavitation test was performed using the rotating disc facility in IPM PAN Gdansk. During the cavitation test, the mass loss of the material with different parameters of laser remelting was determined. Surface and cross-section microstructure of the...
-
Research of hydrotronic variable displacement radial piston pump with electro -pneumatic control
PublicationThe paper presents the developed new electro-pneumatic control (pneumotronic) system for hydraulic fixed-displacement radial piston pump. Hydraulic fixed-displacement radial piston pump equipped with the proposed control system changes into hydrotronic variable-displacement radial piston pump. Pump flow rate control is realized by means of programmable logic controller, electro-pneumatic valves, pneumatic cylinders and a sensor.
-
Port-Based Modelling of Distributed-Lumped Parameter Systems
PublicationThere in the paper is presented an uniform, port-based approach to modelling of both lumped and distributed parameter systems. Port-based model of the distributed system has been defined by application of bond graph methodology and distributed transfer function method (DTFM). The approach proposed combines versatility of port-based modelling and accuracy of distributed transfer function method. The concise representation of lumped-distributed...
-
Effect of the Unit Pressure on the Selection Parameters of Intermetallic Coastings NiAl and Ni3Al after Platic Working
PublicationW artykule omówiono wpływ zgniotu na wybrane parametry warstwy międzymetalicznej NiAl i Ni3Al napawanej na stali C45 podanej obróbce plastycznej poprzez prasowanie na zimno.
-
Modal Reduction and Analysis of Gyroscopic Systems
PublicationThe paper introduces the method of the modal reduction of systems that experience the Coriolis acceleration or gyroscopic effect component. In such cases corresponding system equations are non-self-adjoined. To solve the problem modal reduced model is built up for the system without Coriolis acceleration or gyroscopic effect terms. These phenomena are included by application of any lumping technique. Hence, the final reduced model...
-
Analysis of Asymmetrical Rolling Process of Multilayer Plates
PublicationW niniejszej pracy przedstawiono wyniki badań numerycznych asymetrycznego procesu walcowania blach wielowarstwowych M1E-Al99,8-AlMg5. Modelowanie numeryczne procesu walcowania blach wielowarstwowych przeprowadzono w programie Forge 2D, którego obliczenia bazują na metodzie elementów skończonych. Przedstawione w pracy wyniki umożliwiły przeprowadzenie analizy procesu walcowania blach wielowarstwowych.
-
Surface Roughness Model Components Created by Stereolithography Method
PublicationW pracy przedstawiono charakterystykę powierzchni elementów wykonywanych metodą stereolitografii. Opisano modele chropowatosci stosowane do opisywania powierzcni wraz z prezentacją formuł matematycznych. W oparciu o wyniki badań eksperymentalnych przeprowadzono częściową weryfikację modeli.
-
Modeling and simulation of tool cycle in manufacturing cell
PublicationThe paper addresses issues concerning modeling and analysis of tool flow within a three-machine manufacturing cell used for small batch manufacturing of a definite spectrum of prismatic parts. The approach utilizes a method for job and tool allocation to work centers with limited number of machines and capacity of tool resources, based on the analysis of formalized relations: job - tool sets required. Selected tool flow control...
-
Optimum Control of Gyroscopic Systems
PublicationThe problem of optimum control of transverse rotor vibrations with gyroscopic interactions has been described and solved in the paper. An integral performance index has been defined for such system in order to minimize vibration level of a chosen rotor point. For this reason, an efficient way of finding the weight coefficients of integral performance index for multi-degrees-of-freedom system with gyroscopic interactions has been...
-
Energy-Saving Mechatronic System for Fatigue Tests of Materials under Variable-Amplitude Proportional Bending and Torsion
Publication -
A Noded Carbon Emission Tool (NCET) to Measure Embodied Carbon (EC) in Compositional Cementitious Materials
PublicationThe ever evolving modern construction industry is now producing the highest levels of carbon content adversely affecting the construction associated environment. Although, the impact of carbon induced emission is quite large, but still not enough measurable standards and tools to scale these emission are available. This study contributes to the body of knowledge by providing a Grasshopper based definition to calculate the embodied...
-
Rock salt ordered-type double perovskite anode materials for solid oxide fuel cells
Publication -
Correlation between crystal and transport properties in LnBa0.5Sr0.5Co1.5Fe0.5O5+δ (Ln - selected lanthanides, Y)
Publication -
Enhanced oxygen mobility by doping Yb in BaGd1-xYbxMn2O5+δ double perovskite-structured oxygen storage materials
Publication -
Evaluation of BaY1−Pr Mn2O5+δ oxides for oxygen storage technology
Publication -
Crystal structure and proton conductivity in highly oxygen-deficient Ba1−xLax(In,Zr,Sn)O3−δ perovskites
Publication -
Structure and transport properties of proton-conducting BaSn 0.5 In 0.5 O 2.75 and A-site substituted Ba 0.9 Ln 0.1 Sn 0.5 In 0.5 O 2.8 (Ln = La, Gd) oxides
Publication -
Cation-ordered perovskite-type anode and cathode materials for solid oxide fuel cells
Publication -
Possibility of determination of transport coefficients D and k from relaxation experiments for sphere-shaped powder samples
Publication -
Evaluation of W-containing Sr1−Ba Fe0.75W0.25O3– (x= 0, 0.5, 1) anode materials for solid oxide fuel cells
Publication -
Laser Surface Alloying of Aluminium Alloys with Cu/Fe Metallic Powders
Publication -
Laser Thermal Oxidation by Ytterbium-Doped Fibre Laser of the Hot and Cold-Rolled Stainless Steel Surface
Publication -
The domination of ionic conductivity in tetragonal phase of the organometal halide perovskite CH3NH3PbI3-xClx
PublicationOrganometal trihalide perovskites have recently gained extreme attention due to their high solar energy conversion in photovoltaic cells. Here, we investigate the contribution of iodide ions to a total conductivity of the mixed lead halide perovskite CH3NH3PbI3−xClx with a use of the modified DC Hebb–Wagner polarization method. It has been identified that an ionic conductivity dominates in tetragonal phase which is associated with room...
-
Electrical properties of Na2O-CaO-P2O5 glasses doped with SiO2 and Si3N4
PublicationSodium-calcium-phosphate glasses doped with SiO2 or Si3N4 having similar sodium ion concentrations were prepared by melt quenching. The conductivity was measured by impedance spectroscopy under nitrogen atmosphere in a wide frequency range (10 mHz–1 MHz) and wide temperature range (153–473 K). At 36.6 °C, DC conductivities of all glasses vary between 1.1 ∗ 10−12 and 8.9 ∗ 10−12 S cm−1 and have similar activation energies (between...
-
Nonlinear impedance in oxide glasses containing single and mixed alkali ions
PublicationThe aim of the present was to find more clues on the nonlinearities in impedance of oxide glasses. The first family of researched glasses has a composition of FeO-P2O5-Na2O. Oxide glasses containing iron and alkali are well known for a very low alkali ion mobility and may be considered purely polaron conducting. These glasses show no detectable nonlinearities in the impedance spectra. The second was a family of ionic conducting...
-
Using River Formation Dynamics Algorithm in Mobile Robot Navigation
PublicationRiver Formation Dynamics is a heuristic optimization algorithm based on the manner, in which drops of water form the river bed. The idea is to imitate the movement of drops on the edges between given nodes thus performing a search based on their height, which is modified through the mechanism of soil erosion and sediment deposition. In this way decreasing gradients are constructed, and these are followed by subsequent drops to...
-
Behavior Based Complete Coverage Task of Unknown Area by an Autonomous Mobile Robot SCORPION with Static Obstacles in Environment
PublicationIn the paper the behavior based control system of an autonomous mobile robot SCORPION is presented to execute the one of the most difficult navigation task, which is the complete coverage task of unknown area with static obstacles in the environment. The main principle assumed to design control system was that the robot should cover all area only once, if it possible, to optimize the length of path and energy consumption. All commercial...
-
Investigation of functional layers of solid oxide fuel cell anodes for synthetic biogas reforming
PublicationSolid oxide fuel cells (SOFCs) are one of the most promising energy conversion devices due to their high efficiency, low pollution and fuel flexibility. Unfortunately, when hydrocarbons are used as a fuel, for example in the form of a biogas, solid carbon can deposit on the anode surface. This process leads to the degradation of the fuel cell performance. A possible solution to this problem is to apply an additional catalytic material,...
-
Studies of the Modelling Accuracy of Steam Turbine Control Systems for Diagnostic Tests of Automatic Synchronizers
PublicationOne of the important factors that affect the reliable operation of the power system and the rapid restitution after disaster is a quick and effective combining synchronous electric power facilities to operate in parallel. Hence, diagnostics of automatic synchronizers at every stage of their life, from building a prototype, through the whole life, until removing such devices from the operation, is an extremely important and responsible...
-
The Optimal Spindle Speed Map for Reduction of Chatter Vibration During Milling of Bow Thruster Blade
PublicationW artykule przedstwiono przykład wykorzystania procedury tworzenia mapy optymalnych prędkosci obrotowych w celu ograniczenia drgań samowzbudnych podczas frezowania płata śruby okrętowego steru strumieniowego.
-
Mathematical Models of Control Systems of Angular Speed of Steam Turbines for Diagnostic Tests of Automatic and Mechatronic Devices
PublicationAccurate modeling of physical processes of many automatics and mechatronics systems is often necessity. In power system such a process is control of angular velocity of power objects during connection to operation in parallel. This process is extremely dynamic. For this reason response of control system depends from changes of many physical parameters (temperature, pressure and flow of the medium, etc.). Precision modeling influences...
-
Redundantly Actuated 3RRR Parallel Planar Manipulator - Numerical Analyses of its Dynamics Sensitivity on Modifications of its Platform’s Inertia Parameters
PublicationIn the paper, numerical analyses, as well as dynamics of a complex mechanism, are presented. Two objectives are crucial for the paper: inverse dynamic model is needed (dedicated to be use in the model predictive controller); an identification method is searched (some trajectory parameters are controlled, when specific trajectory is tracked under an open-loop model-based control), as selected parameters must be identified for the...
-
Evaluation of Wear Resistance of Ti alloys used for elements friction of knee endoprosthesis
PublicationThe paper presents research results of resistance to abrasive wear of titanium alloys: Ti6Al4V (commonly used) and Til3Nb13Zr (alloy of new generation) in association with polyethylene (UHMW-PE) predisposed for elements on pair of the knee endoprosthesis. The results were analysed from the point of possibility of an use of new generation titanium alloys as components of such implants. The tests of resistance to abrasive wear of...
-
Determination of Failure Causes of a Steam Turbine Casing
PublicationThe paper presents results of research and failure analysis undertaken to determine failure causes of a steam turbine casing. After 130,000 hours of service the crack in a outer shell of the turbine casing was found. The inner shell of the casing was made of cast steel grade G21CrMoV5-7, and the outer shell of grade G20CrMo4-5. Following research were performed in order to determine causes of the casing failure: chemical analysis;...
-
The Effect of Welding Conditions on Diffusible Hydrogen Content in Deposited Metal
PublicationThe article presents the results of a literature survey and preliminary tests which set out effects of welding conditions on the amount of diffusible hydrogen in deposited metal. Experiments were conducted by using rutile coated electrodes which generate high contents of diffusible hydrogen in deposited metal. The amount of diffusible hydrogen was determined by a glycerin test.Eleven factors were considered: the electrode angle,...
-
Degradation of Gel-Coat Layer in Glass/Polyester Laminate in Seawater Environment
PublicationGlass/polyester laminate coated with gelcoat layer of different thickness 0,5; 1,5; 3 mm was studied in terms of blistering behaviour and water sorption in hot water environment. Blistering was found to be accelerated for thin (0,5 mm) gel-coat layer compared to the thick (1,5; 3 mm), however no significant difference in blistering behaviour was observed between the laminates with gel-coat thickness 1,5 and 3 mm which may suggest...
-
Formation of Porous Structure of the Metallic Materials Used on Bone Implants
PublicationResearch on improvement of structure and fabrication methods of the bone implants are carried out for many years. Research are aimed to shape the structures, that will have a Young's modulus value similar to the value of the human bones Young's modulus. Depending on theporosity, Young's moduli can even be tailored to match the modulus of bone closer than solid metals can, thus reducing the problems associated with stress shielding...
-
Underwater Welding of Duplex Stainless Steel
PublicationThe present work was conducted to assess the weldability of duplex stainless steel at underwater conditions. Interest of underwater welding of this steel grade is connected with necessity of preparing welding repair technologies for subsea pipelines widely used in offshore oil and gas industry. The GMA local cavity welding method was used in the investigations. Welded beads were performed underwater at 0.5 m depth and in the air....