Search
Filters
total: 3632
filtered: 3078
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: power factor correction
-
Verification of safety in low-voltage power systems without nuisance tripping of residual current devices
PublicationLow-voltage power systems require initial and periodical verification to check the effectiveness of protection against electric shock. As a protection in case of fault, automatic disconnection of supply is most often used. To verify such a protection measure, the earth fault loop impedance or resistance is measured. This measurement is easy to perform in circuits without residual current devices. When residual current devices are...
-
Compensation of supply current harmonics, reactive power, and unbalanced load current balance in the closed-loop control of a shunt active power filter
PublicationThis paper presents the compensation tasks performed by a shunt active power filter, including compensation of harmonic currents, reactive power, and an unbalanced load current. The paper demonstrates novel control of the shunt active power filter in a closed-loop system. The control algorithm was verified by performing simulations and compared the simulated results with those obtained in an open-loop control system. All simulations...
-
REDUNDANCY AS A WAY INCREASING RELIABILITY OF SHIP POWER PLANTS
PublicationOne of key ways of assuring a high level of reliability of a ship power plant is to design redundancy of its structural elements, for example redundancy of prime drivers, drivelines etc. This paper deals with issues related to the redundancy as a way increasing dependability of the ship power and propulsion systems. Especially, fundamental characteristics of dependability, major design strategies influencing the reliability, and...
-
Power enhancement of the Brayton cycle by steam utilization
PublicationThe paper presents thermodynamic analysis of the gas-steam unit of the 65 MWe combined heat and power station. Numerical analyses of the station was performed for the nominal operation conditions determining the Brayton and combined cycle. Furthermore, steam utilization for the gas turbine propulsion in the Cheng cycle was analysed. In the considered modernization, steam generated in the heat recovery steam generator unit is directed...
-
Nuclear power plant as a source of electrical energy and heat
PublicationIn this paper certain issues concerning usage of nuclear power plants as sources of not only electric power but also thermal energy will be discussed. For such a solution appeals most of all the need to limit harmful emissions of gases (including CO2) and ashes, which come from the process of burning fossil fuels, as well as the raising demand for network heat and chill. Additionally combined heat and power production brings measurable...
-
Sectarianism as a Factor Shaping Persian Gulf Security
Publication -
The analysis of the empathy factor in students of medical sciences
Publication -
CRH functions as a growth factor/cytokine in the skin
Publication -
Noise as a Factor of Green Areas Soundscape Creation
Publication -
Human Centric Lighting. The New X Factor?
PublicationWe live in challenging times, and one could even claim we’re experiencing a revolution in lighting with LED technology taking over the world. Part of this rapid change involves a concept called Human Centric Lighting (HCL). In Frankfurt this year, during Light+Building, it was the buzzword, with nearly every second manufacturer’s stand claiming they had figured out the special formula necessary to create perfect HCL illumination....
-
Communication as a Factor Limiting University-Business Cooperation
PublicationObjective - Despite the broad extent of the scientific activity dealing with university-business cooperation, Poland has yet to develop a satisfactory cooperation strategy that takes business needs into account. This issue is still relevant due to the need for continuous improvement and resulting benefits aimed at improving enterprise competitiveness. Methodology/Technique - Authors of this article attempt to select an overriding...
-
Current harmonic controller in multiple reference frames for series active power filter integrated with 18-pulse diode rectifier
PublicationThe paper presents the control system and selected results of experimental tests of the AC/DC power converter consisting of an 18-pulse diode rectifier based on coupled reactors and a serial active power filter. Proportional integral controllers with decoupling components are implemented in multiple reference frames for selective line current harmonic suppression. The regulator is provided with a backtracking anti-windup mechanism...
-
Optimal linear control theory in power system application
PublicationPrzedstawiono syntezę stabilizatora systemowego przy wykorzystaniu metodyki Hinf. Zaprojektowany regulator umożliwia uzyskanie lepszych rezultatów w porównaniu z regulatorem odniesienia w szerokim zakresie zmian punktu pracy.
-
Dynamic model of nuclear power plant turbine
PublicationThe paper presents the dynamic multivariable model of Nuclear Power Plant steam turbine. Nature of the processes occurring in a steam turbine causes a task of modeling it very difficult, especially when this model is intended to be used for on-line optimal process control (model based) over wide range of operating conditions caused by changing power demand. Particular property of developed model is that it enables calculations...
-
Problems of Connecting Wind Farms to the Power System with HV Cables
PublicationThis paper presents problems caused by connecting wind farms to a power system with high voltage cables. The author highlights possible problems with reactive power compensation, depending on the arrangement of the shunt reactor connection and settings of control systems for reactive power and voltage of the wind farm. The paper also discusses issues of increasing active power losses caused by a shunt reactor installation.
-
Correction of Huntington’s Disease Phenotype by Genistein-Induced Autophagy in the Cellular Model
Publication -
Strategies for optimizing the phase correction algorithms in Nuclear Magnetic Resonance spectroscopy
Publication -
Some aspects of vibration control. Part I: Active and passive correction.
PublicationPrzedstawiono ogólne podejście do modyfikacji układu mechanicznego w ruchu harmonicznym przy użyciu aktywnych i pasywnych metod. Zaproponowano metodę wyznaczania elementów macierzy układu lub struktury i nastaw regulatora, zapewniającą najefektywniejsze oddziaływanie na dynamikę ruchu.
-
International Competitiveness of Czech Manufacturing: A Sectoral Approach with Error Correction Model
PublicationThe main objective of this paper is to find the determinants of the international competitiveness of the manufacturing sectors of the Czech economy, using the database of 13 manufacturing subsectors in 1995–2011, with the aid of ECM model. The authors research the question of how much foreign and domestic demand, the level of labour costs, the level of sector innovation intensity, the level of sector openness to foreign markets...
-
Application of Web-GIS and Cloud Computing to Automatic Satellite Image Correction
PublicationRadiometric calibration of satellite imagery requires coupling of atmospheric and topographic parameters, which constitutes serious computational problems in particular in complex geographical terrain. Successful application of topographic normalization algorithms for calibration purposes requires integration of several types of high-resolution geographic datasets and their processing in a common context. This paper presents the...
-
Security Assessment of a Turbo-Gas Power Plant
PublicationCritical infrastructures are exposed to new threats due to the large number of vulnerabilities and architectural weaknesses introduced by the extensive use of information and communication technologies. This paper presents the results of an exhaustive security assessment for a turbo-gas power plant.
-
Modelling and analysis of medium frequency transformers for power converters
PublicationThe evolutions in power systems and electric vehicles, related to the economic opportunities and the environmental issues, bring the need of high power galvanically isolated DC-DC converter. The medium frequency transformer (MFT) is one of its key components, enabled by the increasing switching frequency of modern power semiconductors like silicon carbide transistors or diodes. The increased operating frequency offers small...
-
Effective Short -term Forecasting of Wind Farms Power
PublicationForecasting a specific wind farm's generation capacity within a 24 hour perpective requires both a reliable forecast of wind, as well as supporting tools. This tool is a dedicated model of wind farm power. This model should include not only general rules of wind to mechanical energy conversion, but also the farm's specific features. This paper present analytical, statistical, and neuron models of wind farm power. The study is based...
-
Delivery of Ancillary Services in Distribution Power Systems
PublicationOne of the technical and organizational challenges the power system faces in deregulated market conditions is to organize an ancillary services market. The growing share of distributed generation of variable (intermittent) energy sources and a change in the market position of consumers, causes the demand for distributed delivery of ancillary services. For this purpose, it is sought to use the ability of the regulatory measures:...
-
Methodology for the Correction of the Spatial Orientation Angles of the Unmanned Aerial Vehicle Using Real Time GNSS, a Shoreline Image and an Electronic Navigational Chart
PublicationUndoubtedly, Low-Altitude Unmanned Aerial Vehicles (UAVs) are becoming more common in marine applications. Equipped with a Global Navigation Satellite System (GNSS) Real-Time Kinematic (RTK) receiver for highly accurate positioning, they perform camera and Light Detection and Ranging (LiDAR) measurements. Unfortunately, these measurements may still be subject to large errors-mainly due to the inaccuracy of measurement of the optical...
-
Selected problems of decision making modelling in power engineering
PublicationThe paper presents the selected problems of decision making modelling in power engineering specially investment risk evaluation methods. The proposed model can be used in the range programming the development and investing process in power engineering. Decision making problems in power engineering and the evaluation of investment effectiveness in particular are closely related to modelling which relatively accurately reflects...
-
CAES – Energy storage providing stability for national power system
PublicationThis paper presents a short characteristics of the power system. It also describes various types of energy storage technologies. The suggested solution of accumulation and generation of electric power is based on the cooperation of gas turbine with Compressed Air Storage Energy systems – CAES. This analysis describes also various types of cooperation of CAES and renewable sources of energy, particularly wind power systems.
-
Estimation of the Maximum Permissible PV Power to be Connected to the MV Grid
PublicationIn recent decades, a significant increase in the share of renewable energy sources in power grids at various voltage levels has been observed. A number of articles have been published highlighting emerging problems in low-voltage grids with a large share of prosumers and in medium- and high-voltage grids to which photovoltaic (PV) plants are connected. The article analyzes the medium-voltage grid in terms of the possibility of...
-
Structural Health Monitoring of Overhead Power Transmission Lines
PublicationStructural Health Monitoring (SHM) is a novel and continuously developing branch of science and technology that draws attention of scientists all over the world. It creates opportunities to detect, localize and identify structural damage of various types such as: line breakage, permissible sag, bolt loosening, fatigue cracking or insulator contamination. On the other hand the methods used to estimate the remaining operational...
-
Uncertainty analysis of measuring system for instantaneous power research
PublicationThe paper presents a metrological analysis of the measurement system used for diagnosis of induction motor bearings, based on the analysis of the instantaneous power. This system was implemented as a set of devices with dedicated software installed on a PC. A number of measurements for uncertainty estimation was carried out. The results of the measurements are presented in the paper. The results of the aforementioned analysis helped...
-
How to choose drive’s rated power in electrified urban transport?
PublicationSelection of drive's rated power influences not only vehicle's dynamics, but also its energy efficiency. Mentioned above approach requires a multiphysical model, which covers both mechanical and electrical phenomena. This paper discusses how selection of traction drive's rated power influences vehicle energy consumption on example of a trolleybus. A complex mathematical model was developed in Matlab/Simulink to describe the multiphisical...
-
Interdependence between Power Grids and Communication Networks: A Resilience Perspective
PublicationPower network resilience is increasingly dependent on communication networks. Besides traditional generation, power networks need to accommodate increasingly high penetration levels of dispersed micro generation, mostly based on renewable sources, and increasing and challenging demand, such as electric vehicles. At the same time the deployment of enabling technologies throughout the power grid makes available new demand resources...
-
An application of multi-agent system for ship’s power systems design
PublicationDesign process of transport ship power system consists of structure (topology) and component elements selection. Compliance with the requirements for static components does not guarantee optimal dynamic characteristics of entire power system. Design steps are difficult to formalize and as a consequence to this reason expert and multi-agent systems are used for solving selected design issues. In the paper distributed multi-agent...
-
Induced sheath voltages in 110 kV power cables – case study
PublicationThis paper considers electric shock hazard due to induced sheath voltages in 110 kV power cables. The purpose of this paper is to find an optimal configuration of the power cable system, taking into account electric shock hazard and ability of the system to transfer maximal power. A computer simulations on a computer model of the local power system, comprising high voltage power cables, were carried out. This model enables to analyse...
-
Methods for evaluating rated power of diesel-powered generator set
PublicationBasic concepts for evaluating rated power of generator sets powered by combustion engines are presented in this article. A relation between parameters of the engine and the generator are shown. Recommendations contained in the standards and technical literature are systematized. The scheme and methodology for evaluating rated power of the generator set, based on laboratory research, are suggested. Also, the main problems which...
-
Can mutations in the gene encoding transcription factor EKLF (Erythroid Krüppel-Like Factor) protect us against infectious and parasitic diseases?
Publication -
Low-Power WSN System for Honey Bee Monitoring
PublicationThe paper presents a universal low-power system for biosensory data acquisition in scope of bees monitoring. We describe the architecture of the system, energy-saving components as well as we discuss the selection of used sensors. The work focuses on energy optimization in a scope of wireless communication. A custom protocol was implemented, which is the basis for presented energy-efficient devices. Data exchange process during...
-
Diagnostic Analysis of Exhaust Gas with A Quick-Changing Temperature from a Marine Diesel Engine Part II / Two Factor Analysis
PublicationThe article presents a continuation of research carried out to determine the effect of input parameters (changes in engine structure parameters) on selected output parameters (diagnostic measures), based on quickly changing exhaust gas temperature. A method of determining the simultaneous influence of two input factors (the structure parameter and the engine load) on one output factor was presented, as well as an evaluation...
-
Power electronic transformer based on cascaded H-bridge converter
PublicationIn this paper the control strategy of power electronic transformer (PET) is proposed. The analyzed structure of PET uses two seven-level cascaded H-bridge (CHB) rectifiers. The electrical power of PET is transferred between DC-links of CHB converters using dual-active-bridges (DABs) and low voltage high frequency transformers. The roposed solution allows for controlling the active and reactive power with a low level of harmonic...
-
Research of Emergency Modes of Wind Power Plants Using Computer Simulation
PublicationThe aim of this study is to investigate changes in the wind power plant energy production parameters under the conditions of sudden wind changes and voltage drop. To achieve these goals, a simulation of operation of wind power plants was performed. Twelve wind turbines with variable rotational speed equipped with a Fuhrländer FL 2500/104 asynchronous double-fed induction generator (DFIG) were used, each with an installed capacity...
-
Utility analysis and rating of energy storages in trolleybus power supply system
PublicationThe article discusses two energy storage applications in power supply system of public electrified transport. The first application aims at reducing the peak power of the traction substation. The second application increases effectiveness of using solar power plant to cover partial power demand of traction supply system. These two applications were discussed and analyzed based on trolleybus supply system in Gdynia, where most measurements...
-
Performance Evaluation of a 650V E-HEMT GaN Power Switch
PublicationGaN power switches have better characteristics compared to the state-of-the-art Si power transistors. These devices offer high operating temperature and current densities, fast switching and low on-resistance. However, currently only a few producers offer technology of high voltage GaN transistors. Immaturity of this technology is the reason why experimental evaluation of GaN parameters must be performed to properly exploit their...
-
Application of dynamic factor models for inflation forecasting in Poland
Publication -
Estimating and Forecasting GDP in Poland with Dynamic Factor Model
Publication -
SERRATE: a key factor in coordinated RNA processing in plants
Publication -
Probability of flooding a compartment (the pi factor) - a critique and a proposal
PublicationArtykuł podaje krytyczny przegląd stanu wiedzy dot. obliczania prawdopodobirństwa zatopienia przedziału (mnożnika pi), ze szczególnym uwzględnieniem projektu badawczego ''Harder'' oraz podaje poprawne rozwiązanie dotyczące tego mnożnika. Kończy się propozycją przepisu do zamieszczenia w konwencji SOLAS.
-
Technological logistics HL as a factor in distribution network effectivness
PublicationPrzedstawiono podział kompetencyjny logistyki i wskazano na znaczenie logistyki technicznej HL (HardLogistics). Jako przykład wpływu logistyki HL na efektywność ekonomiczną systemu dystrybucji zamieszczono wyniki symulacji wyniku eksploatacji pojazdów samochodowych o różnym wyposażeniu w urządzenia przeładunkowe.
-
Corrosion monitoring as a factor increasing the safety of hydrotechnical infrastructure
PublicationWater distribution systems at KGHM S.A. are of great importance for the efficient production of copper and environmental protection. For failures leading to perforation and leakage, the corrosion processes are responsible. This paper aims to assess corrosion on the basis of the analysis of the exposure of the Hydrotechnical Plant pipelines. To this end, the system of transfer and deposition of post-flotation waste as well as the...
-
Factor Analysis of the Polish Version of Godspeed Questionnaire (Gqs)
Publication -
THE INFLUENCE OF PHASE SHIFTERS ON THE VOLTAGE STABILITY OF CONNECTED POWER SYSTEMS
PublicationThe paper presents the results of simulation tests of connected power systems in which phase shifters were installed on cross-border links. The analysis was carried out in terms of assessing the impact of shifters on node voltage stability. Individual systems were characterized by different balance of active power: deficit or excess. The evaluation of voltage stability was based on the dU/dQ and dU/dP criteria.