Search
Filters
total: 4750
filtered: 3848
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: PORE WATER PRESSURE
-
Large deformation modelling of CPT probing in soft soil—pore water pressure analysis
PublicationThis paper presents the results of finite element modelling with Updated Lagrangian formulation of the Cone Penetration Test in soft soil deposit located in Jazowa, Poland. The numerical calculations are carried out for homogenous, normally consolidated, organic soil layer. The Modified Cam Clay constitutive model for soft soil and Coulomb model for interface are used. The study compares the registered pore water pressure distributions...
-
LDFEM analysis of pore water pressure development in cohesive soil due to FDP auger drilling
PublicationThis paper presents the preliminary modelling of FDP auger drilling in soft soil with emphasis on excess pore water pressure (EPWP) development using CEL formulation and Abaqus software suit. The EPWP generation in single points is investigated and the results of a numerical analysis are compared with the field measurements. It is found that numerical model qualitatively reflects the field measurements. However,...
-
Pore Water Pressure Development in Soft Soil due to Installation and Loading of Controlled Modulus Columns
PublicationExcess pore water pressure (EPWP) development and decay due to the installation and static loading tests of controlled modulus columns (CMC) in soft soil was measured with piezometers equipped with low air entry (LAE) filters and a piezocone (CPTU) equipped with a high air entry (HAE) filter. The HAE filter allows for detailed detection of EPWP in short time intervals during construction of CMC. The influence zone due to the installation...
-
Some remarks on the pore water pressure dissipation patterns from the one-dimensional consolidation test
Publication -
Experimental insights into consolidation rates during one-dimensional loading with special reference to excess pore water pressure
Publication -
Wave-induced pore pressure oscillations in sandy seabed sediments
PublicationPracę poświęcono zagadnieniu wywoływania cyklicznych oscylacji ciśnieniacieczy porowej w piaszczystym gruncie dna morskiego w wyniku oddziaływania progresywnego falowania powierzchniowego. Dokonano szerokiego przeglądu i analizy istniejących teorii ciśnień cieczy porowej z punktu widzenia skom- plikowania opisu matematycznego zachowania się ośrodka wodno-gruntowego. Wyprowadzono dwuwymiarowe rozwiązanie analityczne i...
-
Constituents of organic alkalinity in pore water of marine sediments
Publication -
Hydrodynamic Pressure Field of a Ship on Shallow Water
PublicationResults of calculations of the hydrodynamic pressure field around the ship were obtained by application of the boundary element method. Hydrodynamic field was calculated for a Polish Navy’s tugboat and transport ship using a program called SHiPP and compared with measurements of the field taken on river near Swinoujscie for two identical tugs H-4 and H-10. Next, a series of HPF calculations was carried out on planes situated at...
-
Low-Pressure Injection of Water and Urea-Water Solution in Flash-Boiling Conditions
Publication -
Deep submarine groundwater discharge indicated by pore water chloride anomalies in the Gulf of Gdańsk, southern Baltic Sea
Publication -
Pore water alkalinity below the permanent halocline in the Gdańsk Deep (Baltic Sea) - Concentration variability and benthic fluxes
Publication -
The Influence of Water and Mineral Oil on Pressure Losses in Hydraulic Motor
PublicationIn this paper, pressure losses in hydraulic motor supplied with water and mineral oil (two liquids that have significantly different viscosity and lubricating properties) are described and compared. The experimental tests were conducted using a hydraulic satellite motor that is dedicated to working with different liquids, including water. The methodology of measuring the pressure drop in internal channels of this motor is also...
-
Analysis of hydrodynamic pressure fields of motorboats and pontoons in shallow water
PublicationThe article presents the results of calculations of the pressure fields generated by a motorboat at the bottom of a shallow sea. Calculations were made using the boundary elements method (BEM), arranged on the surface of the boat and the bottom of the sea. This method is described in [3], and applied on a free surface linearized boundary condition. Results for four different lengths of motorboats, from 2.85 m to 9.5 m, sea depth...
-
Pore water phosphate and ammonia below the permanent halocline in the south-eastern Baltic Sea and their benthic fluxes under anoxic conditions
Publication -
Hydrophobic PVDF hollow fiber membranes with narrow pore size distribution and ultra-thin skin for the fresh water production through membrane distillation
Publication -
The effect of pressure on heat transfer during pool boiling of water-Al2O3 and water-Cu nanofluids on stainless steel smooth tubes
PublicationPrzedstawiono wyniki badań eksperymentalnych wrzenia nanocieczy woda-Al2O3 i woda-Cu o koncentracjach nanocząstek 0.01%, 0.1% oraz 1% przy ciśnieniu absolutnym 10 kPa, 100 kPa oraz 200k Pa.
-
The effect of pressure on heat transfer during pool boiling of water-Al2O3 and water-Cu nanofluids on stainless steel smooth tube
PublicationPrzedstawiono wyniki badań eksperymentalnych wrzenia nanocieczy woda-Al2O3 i woda-Cu o koncentracjach nanocząstek 0.01%, 0.1% oraz 1% przy ciśnieniu absolutnym 10 kPa, 100 kPa oraz 200k Pa.
-
Analysis of energy recovery from surplus water pressure of municipal heat distribution network
Publication -
Experimental studies on the impact of changing the pipe material on the propagation of the pressure wave during water hammer
PublicationAim of the paper is to present the results studying the water hammer phenomenon in pipes made of different materials, and to show the impact of changing the type of material of the pipe on the velocity of the pressure wave during the transient flow in the pipes. In terms of research material and methods, pipes made of galvanized steel and high-density polyethylene were tested. Measurements were made using strain gauges with a high...
-
Experimental study of pressure rise at the evaporator of capillary pumped loop with acetone and water as working fluids
PublicationIn this work studied is the possibility of fluid pumping using capillary forces in the capillary pumped loop. Experimental and theoretical studies have been performed to understand the phenomena associated with heat transfer in porous structure of the evaporator. The capillary effect was studied during operation of two different capillary porous structures with two different working fluids, namely water and acetone. The results...
-
Changes in the Thickness of Ice Cover on Water Bodies Subject to Human Pressure (Silesian Upland, Southern Poland)
Publication -
Modelling of Capillary Pressure-driven Water Flow in Unsaturated Concrete Using Coupled DEM/CFD Approach.
PublicationSformułowano nowatorskie, połączone podejście do modelowania dwufazowego przepływu wody napędzanego kapilarami w nienasyconym betonie. Dzięki połączeniu metody elementów dyskretnych (DEM) z obliczeniową dynamiką płynów (CFD) w warunkach izotermicznych proces został zbadany numerycznie w mezoskali w warunkach dwuwymiarowych. Niewielkie próbki betonu o uproszczonej mezostrukturze cząstek poddano w pełni sprzężonym hydromechanicznym...
-
Experimental and comparative study on the two-phase pressure drop of air-water mixture in U-bend and straight pipe annuli
PublicationIn this paper, the experimental and theoretical analysis of pressure drop in singlephase and two phase-flow were presented for straight and U-bend smooth tube annulus and tube annulus with wire coil insert. Experiments for various boundary conditions were performed. In case of U-tube and straight tube with and without turbulator, tests were made for the water-water and air-water systems. The study covered a wide measuring range,...
-
Improvement of the Water Resistance of a Narrow-Band Red-Emitting SrLiAl3N4:Eu2+Phosphor Synthesized under High Isostatic Pressure through Coating with an Organosilica Layer
Publication -
Wpływ warunków ciśnieniowej filtracji na przebieg biologicznego usuwania azotu amonowego z wody w procesie nitryfikacji = Effect of pressure filtration conditions on nitrification process used for ammonia nitrogen removal from water
PublicationW pracy przedstawiono wyniki badań laboratoryjnych nad wpływem podwyższonego, zmiennego ciśnienia (do 0,8 MPa) na przebieg usuwania azotu amonowego z wody na nitryfikacyjnym złożu filtracyjnym. Wykazano, że ani podwyższone ciśnienie, ani jego zmiany nie wpływają hamująco na przebieg procesów nitryfikacji. Stwierdzono pozytywny wpływ płukania filtrów biologicznych na usuwanie azotu amonowego z wody.
-
The Influence of Loop Heat Pipe Evaporator Porous Structure Parameters and Charge on Its Effectiveness for Ethanol and Water as Working Fluids
PublicationAbstract: This paper presents the results of experiments carried out on a specially designed experimental rig designed for the study of capillary pressure generated in the Loop Heat Pipe (LHP) evaporator. The commercially available porous structure made of sintered stainless steel constitutes the wick. Three different geometries of the porous wicks were tested, featuring the pore radius of 1, 3 and 7 um. Ethanol and water as two...
-
Influence of the air phase on water flow in dikes
PublicationNumerical models are often used to describe flow and deformation processes occurring in dikes during flood events. Modeling of such phenomena is a challenging task, due to the complexity of the system, consisting of three material phases: soil skeleton, pore water and pore air. Additional difficulties are transient loading caused by variable in time water levels, heterogeneity of the soil or air...
-
Simulations of air and water flow in a model dike during overflow experiments
PublicationFlow in flood dikes, earth dams, and embankments occurs in variably saturated conditions, with pores of the earth material filled partly with water and partly with air. In routine engineering analysis, the influence of pore air is neglected and the air pressure is assumed equal to atmospheric. In some circumstances, for example, during overtopping of the dike by water, the effect of pore air on water flow and stability of the structure...
-
Effect of free water on the quasi‑static compression behavior of partially‑saturated concrete with a fully coupled DEM/CFD approach.
PublicationThe work aims to numerically investigate the quasi-static response of partially fluid-saturated concrete under two-dimensional uniaxial compression at the mesoscale. We investigated how the impact of free pore fluid content (water and gas) affected the quasi-static strength of concrete. The totally and partially fluid-saturated concrete behavior was simulated using an improved pore-scale hydro-mechanical model based on DEM/CFD....
-
SUBSOIL CHARACTERISTICS OF THE VISTULA RIVER DIKES
PublicationThe results of CPTU tests are used to determine the strength parameters of a dike subsoil. Stress state and stress history of the subsoil under the flood embankment was evaluated with CPTU and DMT tests. Normally consolidated soil was found under the central part of the dike, while the subsoil near the dike toe is found to be overconsolidated. Due to consolidation the undrained shear strength of the subsoil under the central part...
-
Air trapping problem during infiltration on the large areas
PublicationThe process of flow modeling in unsaturated porous medium is often found in many fields of sciences: geology, fluid mechanics, thermodynamics, microbiology or chemistry. Problem is relatively complicated due to complexity of the system which contains three phases: water, air and soil skeleton. The flow of water in such a medium can be described using two-phase (2PH) flow formulation, which accounts the inflow of air and water phases,...
-
Numerical Simulations of Seepage in Dikes Using unsaturated and Two-Phase Flow Models
PublicationModeling of water flow in variably saturated porous media, including flood dikes, is often based on the Richards equation, which neglects the flow of pore air, assuming that it remains at constant atmospheric pressure. However, there is also evidence that the air flow can be important, especially when the connectivity between the pore air and atmospheric air is lost. In such cases a full two-phase air-water flow model should be...
-
COMMENTS ON EXISTING ANALYTICAL SOLUTIONS TO THE WAVE-INDUCED CYCLIC RESPONSE OF A POROUS SEABED OF INFINITE THICKNESS
PublicationThis paper deals with the wave-induced cyclic response of a porous seabed (by means of oscillating parameters: pore-fluid pressure, soil displacement components, effective normal stress and shear stress components) due to a surface sinusoidal water-wave propagating over a seabed of infinite thickness. The main existing analytical solutions to the governing problem are critically discussed, pointing out their meaningful errors and...
-
A facile approach to fabricate load-bearing porous polymer scaffolds for bone tissue engineering
PublicationBiodegradable porous scaffolds with oriented interconnected pores and high mechanical are load-bearing biomaterials for bone tissue engineering. Herein, we report a simple, non-toxic, and cost-effective method to fabricate high-strength porous biodegradable scaffolds, composed of a polymer matrix of polycaprolactone (PCL) and water-soluble poly (ethylene oxide) (PEO) as a sacrificial material by integrating annealing treatment,...
-
Effects of full displacement pile installation on the stress and deformation state of surrounding soil: review
PublicationSeveral field and model tests have been conducted to investigate the impact of pile installation on bearing capacity. However, little is known about how piles behave during installation, how they interact with the surrounding soil, and how this affects sandy soil properties. This review paper investigates the effect of pile driving on surrounding sandy soil as it compacts sandy soil near to the pile. For this purpose, various related...
-
Prediction of Pile Shaft Capacity in Tension Based on Some Direct CPT Methods—Vistula Marshland Test Site
PublicationThis paper presents different CPT methodologies for the prediction of the pile shaft resistance in tension on the example of three reference screw piles of the Jazowa test site in Poland. The shaft capacity was estimated based on the cone resistance, sleeve friction and CPT excess pore water pressure. Three piles with diameter 0.4 m and the length varied from 8 m to 14.6 m were subjected to static load tests in tension. Their...
-
A pore-scale thermo–hydro-mechanical model for particulate systems
PublicationA pore scale numerical method dedicated to the simulation of heat transfer and associated thermo–hydro-mechanical couplings in granular media is described. The proposed thermo–hydro-mechanical approach builds on an existing hydromechanical model that employs the discrete element method for simulating the mechanical behavior of dense sphere packings and combines it with the finite volume method for simulating pore space fluid flow...
-
Prediction of pile shaft capacity in tension based on some direct CPT methods – Vistula Marshland test site
PublicationThis paper presents different CPT methodologies for the prediction of the pile shaft resistance in tension on the example of three reference screw piles of the Jazowa test site in Poland. The shaft capacity was estimated based on the cone resistance, sleeve friction and CPT excess pore water pressure. Three piles with a diameter of 0.4 m and the length...
-
Importance of sign conventions on analytical solutions to the wave-induced cyclic response of a poro-elastic seabed
PublicationThis paper discusses the influence of different sign conventions for strains and stresses, i.e. the solid mechanics sign convention and the soil mechanics sign convention, on the form of governing partial differential equations (the static equilibrium equations and the continuity equation) used to describe the wave-induced cyclic response of a poro-elastic seabed due to propagation of a sinusoidal surface water-wave. Some selected...
-
Influence of pore formers on electrical properties of CaTi0.9Fe0.1O3-δ perovskite-type ceramics
PublicationPorous CaTi0.9Fe0.1O3-δ (CTF) perovskites were synthesized by the standard solid state method at different sintering temperatures with carbon black (CB), corn starch (CS) and potato starch (PS) as pore-forming agents. The ceramic samples of porosity between 9% and 42% with 5 - 40 μm pore sizes, were obtained by a 6 h sintering at either 1130º C or 1200º C of precursor powder prepared at 1470º C. X-ray diffraction analysis proved...
-
Zastosowanie nowatorskich materiałów geosyntetycznych w konstrukcjach oporowych z gruntu zbrojonego
PublicationArtykuł prezentuje metodę projektowania stromych skarp wznoszonych z gruntów słabo przepuszczalnych, zbrojonych geosiatkami drenującymi. Z analiz przeprowadzonych dla różnej wodoprzepuszczalności gruntu i różnej geometrii skarpy wynika, że pionowy rozstaw i długość zbrojenia mają istotne znaczenie dla stateczności skarpy. Dla gruntów słabo przepuszczalnych, o typowych wartościach współczynników ściśliwości objętościowej oraz konsolidacji,...
-
A geophysical, geochemical and microbiological study of a newly discovered pockmark with active gas seepage and submarine groundwater discharge (MET1-BH, central Gulf of Gdańsk, southern Baltic Sea)
PublicationHigh-resolution bathymetric data were collected with a multi-beam echosounder in the southern part of the Baltic Sea (region MET1, Gulf of Gdańsk) revealing the presence of a 10 m deep and 50 m in diameter pockmark (MET1-BH) on the sea bottom (78.7 m). To date, no such structures have been observed to reach this size in the Baltic Sea. The salinity of the near-bottom water in the pockmark was about 2 PSU (about 31.22 mmol/l...
-
The preparation and evaluation of core-shell magnetic dummy-template molecularly imprinted polymers for preliminary recognition of the low-mass polybrominated diphenyl ethers from aqueous solutions
PublicationThe design, preparation process, binding abilities, morphological characteristic and prospective field of application of dummy-template magnetic molecularly imprinted polymer (DMMIP) for preliminary recognition of the selected low-mass polybrominated diphenyl ethers (PBDE-47 and PBDE-99) from aquatic environment were investigated. The surface of iron oxide (Fe3O4) nanopowder (50-100 nm particles size) was modified with tetraethoxysilane...
-
Hyperbranched polyethylenimine functionalized silica/polysulfone nanocomposite membranes for water purification
PublicationHyperbranched polyethyleneimine functionalized silica (PEI-SiO2) nanoparticles with considerable hydrophilicity were synthesized and incorporated into a polysulfone (PSF)/dimethylacetamide (DMA)/polyvinylpyrrolidone (PVP) membrane casting solution in five different ratios to fabricate PEI-SiO2/PSF nanocomposite membranes using nonsolvent-induced phase separation. The hydrophilic PEI-SiO2 nanoparticles were characterized by TEM,...
-
Fouling mechanisms in anoxic-aerobic sequencing batch membrane bioreactor based on adapted Hermia models and main foulant characteristics
PublicationVarious derivatives of Hermia models (complete pore blocking, intermediate pore blocking, cake layer formation, and standard pore blocking) and different assessments of foulant characteristics have long been used to determine the membrane fouling mechanisms. Accordingly, this study aims to adapt Hermia models and their combination according to the operating conditions of an anoxic-aerobic sequencing batch membrane bioreactor (A/O-SBMBR)....
-
Raz jeszcze o obciążeniu hydrodynamicznym falochronu pionowościennego falą stojącą
PublicationPrzedstawienie istniejących modeli matematycznych opisujących rozkłady ciśnienia hydrodynamicznego na falochron pionowościenny w wyniku oddziaływania fali stojącej. Analiza nieciągłości ciśnienia. Jakościowe porównanie metod obliczeniowych dla wybranych warunków wodno-falowych.
-
Przykłady realizacji i interpretacji wyników sondażowych pomiarów terenowych w czynnych systemach wodociągowych
PublicationW pracy przedstawiono przebieg realizacji i rezultaty sondażowych pomiarów terenowych w trzech układach dystrybucji wody o zróżnicowanym przewymiarowaniu sieci wodociągowej. Pomiary przeprowadzono w dążeniu do identyfikacji właściwości (cech) strukturalnych i funkcjonalnych układów po wieloletniej ich eksploatacji. Ustalenia te determinują opracowanie programu realizacji pomiarów dla potrzeb tarowania komputerowego modelu przepływu...
-
Przykłady realizacji i interpretacji wyników sondażowych pomiarów terenowych w czynnych systemach dystrybucji wody
PublicationW pracy przedstawiono przebieg realizacji i rezultaty sondażowych pomiarów terenowych w trzech układach dystrybucji wody o zróżnicowanym przewymiarowaniu sieci wodociągowej. Pomiary przeprowadzono w dążeniu do identyfikacji właściwości (cech) strukturalnych i funkcjonalnych układów po wieloletniej ich eksploatacji. Ustalenia te determinują opracowanie programu realizacji pomiarów dla potrzeb tarowania komputerowego modelu przepływu...
-
Hydrogen direct reduction and reoxidation behaviour of high-grade pellets
PublicationHigh grade pellets with basicity index close to 0.5 were directly reduced in pure hydrogen atmosphere. The reduction experiments were performed in the temperature range 800 e1000 C at the pressure of 8 bar. The pellets internal structure was analysed through micro tomography observations in the unreduced and reduced conditions. After reduction, the pellets showed a variation of porosity up to more than 15% with a remarkable change...
-
Structural and Material Determinants Influencing the Behavior of Porous Ti and Its Alloys Made by Additive Manufacturing Techniques for Biomedical Applications
PublicationOne of the biggest challenges in tissue engineering is the manufacturing of porous structures that are customized in size and shape and that mimic natural bone structure. Additive manufacturing is known as a sufficient method to produce 3D porous structures used as bone substitutes in large segmental bone defects. The literature indicates that the mechanical and biological properties of scaffolds highly depend on geometrical features...