Search
Filters
total: 756
filtered: 633
Search results for: WET COMBUSTION CHAMBER
-
Numerical modeling of the combustion in a lab-scale pulverized-coal fired combustion chamber
PublicationThis work presents results of numerical modeling of the combustion process inside a lab-scale drop-tube chamber, designed to investigate the slagging properties of the flue ashes, created through the solid fuel firing. Interaction between turbulence and chemistry is accounted by use of probability density function (PDF). FLUENT inputs for non-premixed combustion chemistry modeling are defined. A discrete second phase of the coal...
-
Numerical modeling of the combustion in a lab-scale pulverized-coal fired combustion chamber
PublicationThis work presents results of numerical modeling of the combustion process inside a lab-scale drop-tube chamber, designed to investigate the slagging properties of the flue ashes, created through the solid fuel firing. Interaction between turbulence and chemistry is accounted by use of probability density function (PDF). FLUENT inputs for non-premixed combustion chemistry modeling are defined. A discrete second phase of the coal...
-
Four-stroke engine with central located, dyvided combustion chamber
PublicationW artykule przedstawiono oryginalne rozwiązanie konstrukcyjne nowoczesnego czterosuwowego silnika spalinowego z centralnie umieszczoną, dzieloną komorą spalania. Rozwiązanie takie umożliwia znacznie lepsze wykorzystanie ciepła, co oznacza wyższą sprawność i mniejsze zużycie paliwa oraz niższą emisję szkodliwych gazów takich, jak tlenki azotu (NO2), węglowodory (HC) i dwutlenek węgla (CO2). Silnik może pracować na paliwo płynne...
-
Gas Turbine Cycle with External Combustion Chamber for Prosumer and Distributed Energy Systems
PublicationThe use of various biofuels, usually of relatively small Lower Heating Value (LHV), affects the gas turbine efficiency. The present paper shows that applying the proposed air by-pass system of the combustor at the turbine exit causes tan increase of efficiency of the turbine cycle increased by a few points. This solution appears very promising also in combined gas/steam turbine power plants. The comparison of a turbine set operating...
-
Investigation of the Efficiency of a Dual-Fuel Gas Turbine Combustion Chamber with a Plasma‒Chemical Element
PublicationThe study is devoted to the possibility of increasing the efficiency of the working process in dual-fuel combustion chambers of gas turbine engines for FPSO vessels. For the first time, it is proposed to use the advantages of plasma‒chemical intensification of the combustion of hydrocarbon fuels in the dual-fuel combustion chambers, which can simultaneously operate on gaseous and liquid fuels. A design scheme of a combustion chamber...
-
INVESTIGATION OF THE CHARACTERISTICS OF A LOWEMISSION GAS TURBINE COMBUSTION CHAMBER OPERATING ON A MIXTURE OF NATURAL GAS AND HYDROGEN
PublicationT his article is devoted to the investigation of the characteristics of a low-emission gas turbine combustion chamber, which can be used in Floating Production, Storage and Offloading (FPSO) vessels and operates on a mixture of natural gas and hydrogen. A new approach is proposed for modelling the processes of burning out a mixture of natural gas with hydrogen under preliminary mixing conditions in gaseous fuel with an oxidizer...
-
Investigations of the Working Process in a Dual-Fuel Low-Emission Combustion Chamber for an FPSO Gas Turbine Engine
PublicationThis investigation is devoted to an analysis of the working process in a dual-fuel low-emission combustion chamber for a floating vessel’s gas turbine. The low-emission gas turbine combustion chamber with partial pre-mixing of fuel and air inside the outer and inner radial-axial swirlers was chosen as the object of research. When modelling processes in a dual-flow low-emission gas turbine combustion chamber, a generalized method...
-
Investigation of ecological parameters of a gas turbine combustion chamber with steam injection for the floating production, storage, and offloading vessel
PublicationThe article is dedicated to the investigation of the possibility of using the contact type gas turbine cycle with steam injection into the combustion chamber for the floating production, storage, and offloading vessel in order to increase the specific power and efficiency and reduce emissions of toxic components. A new approach is proposed, associated with the use of the two-stage injection of superheated steam into a gas turbine...
-
INVESTIGATIONS OF THE EMISSION CHARACTERISTICS OF A DUAL-FUEL GAS TURBINE COMBUSTION CHAMBER OPERATING SIMULTANEOUSLY ON LIQUID AND GASEOUS FUELS
PublicationT his study is dedicated to investigations of the working process in a dual-fuel low-emission combustion chamber for a floating vessel’s gas turbine. As the object of the research, a low-emission gas turbine combustion chamber with partial premixing of fuel and air inside the outer and inner radial-axial swirls was chosen. The method of the research is based on the numerical solution of the system of differential...
-
Compact High Efficiency and Zero-Emission Gas-Fired Power Plant with Oxy-Combustion and Carbon Capture
PublicationReduction of greenhouse gases emissions is a key challenge for the power generation industry, requiring the implementation of new designs and methods of electricity generation. This article presents a design solution for a novel thermodynamic cycle with two new devices—namely, a wet combustion chamber and a spray-ejector condenser. In the proposed cycle, high temperature occurs in the combustion chamber because of fuel combustion...
-
A study of a compact high-efficiency zero-emission power plant with oxy-fuel combustion
PublicationThis paper discusses the application of global trends in gas cycles technology using oxy-fuel combustion. This is followed by a demonstration of a design solution for a new cycle with two enhanced energy-converting devices, namely a wet combustion chamber and a spray-ejector condenser. The proposed gas and steam cycle unit is contained within a single turbine, whose benefits combine those offered by gas turbines (high inlet temperatures)...
-
Porous structures in aspects of transpirating cooling of oxycombustion chamber walls
PublicationA wet oxycombustion chamber, which must be effectively cooled due to high temperature evolved during the oxy-combustion process, by using the phenomena of Reynolds thermal transpiration and Navier slip velocity. Closures needed to execute mass flow rate in a microchannel, which should be treated as a single porous structure in the walls of the combustion chamber, have been obtained by applying a local 3D approach. The Navier-Stokes...
-
Carbon Dioxide Recovery Skid
PublicationIn the face of tightening climate regulations, the adoption of carbon dioxide recovery systems is inevitable. Modular process skid units have been widely adopted across the industry. The gas-steam power plant skid unit with the carbon dioxide recovery system was described. The proposed skid module consists of the compact cycle with the oxy-combustion and the carbon dioxide capture skid unit producing pure compressed CO2. The compactness...
-
OPTIMIZATION OF THE LAST STAGE OF GAS-STEAM TURBINE USING A HYBRID METHOD
PublicationThis paper relates to the CFD calculation of a new turbine type which is in the phase of theoretical analysis, because the working fluid is a mixture of steam and gas generated in wet combustion chamber. At first, this article concentrates on a possibility of streamlining the flow efficiency of a last stage of axial turbine working on gas-steam mixture using a hybrid of the particle swarm optimization algorithm with the Nelder-Mead...
-
Design and computational fluid dynamics analysis of the last stage of innovative gas-steam turbine
PublicationResearch regarding blade design and analysis of flow has been attracting interest for over a century. Meanwhile new concepts and design approaches were created and improved. Advancements in information technologies allowed to introduce computational fluid dynamics and computational flow mechanics. Currently a combination of mentioned methods is used for the design of turbine blades. These methods enabled us to improve flow efficiency...
-
Exergetic Analysis of the nCO2PP Cycle with Particular Reference to the Exergy Destruction of Sewage Sludge Due to Gasification
PublicationAn exergy analysis is carried out on the negative CO2 emission gas power plant (nCO2PP), which integrates the process sections of fuel preparation, power generation and carbon capture. Processes of exergy destruction are studied with particular focus on the process in the gasification unit of the fuel preparation section, where a large amount of exergy is destroyed in various chemical reactions from sewage sludge to producer gas...
-
On design and analysis of flow characteristics of the last stage of gas-steam turbine
PublicationResearch regarding blade design and analysis of flow have been conducted for over a century. Meanwhile new concepts and design approaches were created and improved. Advancements in information technologies allowed to introduce computational fluid dynamics (CFD) and computational flow mechanics (CFM). Currently a combination of mentioned methods is used for design of turbine blades. These methods enabled us to improve flow efficiency...
-
Analysis of pressure ratio in the intake in dependence on high-voltage behaviours
PublicationPower control in spark ignition engines by regulating the intake air is performed. The control unit needs information about the air pressure conditions which then enters the combustion chamber. The information about the intake air pressure is an important quantity for optimal control of combustion mixtures. The paper describes some types of sensors that are used to measure the air intake temperature. Air pressure in the intake...
-
Modeling of low calorific gas burning in a deficient oxygen environment and high-temperature oxidizer
PublicationThe experimental research will be performed using the experimental facility with a combustion chamber. The oxygen concentration in combustion oxidizers will be varied from 21% by volume (normal) air to 2%. The test combustion chamber will be fed with propane or methane as the reference fuel, then with low calorific fuels as test gases obtained by mixing various combustible components, e.g. H2, CH4, CO, and neutral gases, e.g. N2,...
-
Technical and economic analysis of energy storage in the compressed air technology with low capacity for the production plant
PublicationCompressed air energy storage (CAES) system is a promising technology due to its numerous advantages, including relatively low maintenance cost, a long lifespan and high operational flexibility. This article explores the possibility of designing a CAES power plant as a source of electricity and heat for an existing industrial plant. The study involves the technical analysis of the power plant parameters and the economic analysis...
-
Analysis of the macrostructure of the fuel spray atomized with marine engine injector
PublicationOne of the main problem influencing the combustion process in the cylinder of the marine engine is an fuel spray phenomena. The parameters describing the shape of the fuel spray are named macro parameters. This article presents the research results of the macrostructure parameters of the fuel spray atomized with the marine engine injector. The research were carried out by optical visualization measurement method of Mie scattering....
-
Design and distribution of air nozzles in the biomass boiler assembly
PublicationDue to energy crisis as well as increasing pollution of the environment, renewable energy sources usage increases all over the world. These facts encouraged authors to start research over developing a uniform biomass boiler calculation model. This paper presents a design of biomass boiler assembly created for ORC (Organic Rankine Cycle) unit since these systems could achieve strong position in energy industry....
-
On energy, exergy, and environmental aspects of a combined gas-steam cycle for heat and power generation undergoing a process of retrofitting by steam injection
PublicationThe paper presents a study of retrofitting of a combined heat and power (CHP) plant aimed to increase the electric to heating power ratio. The modification would involve diverting part of the steam to the gas turbine, instead of letting it go to the steam turbine, using injection technique into a combustion chamber. Therefore, two potential retrofitting approaches are analyzed: steam injection gas turbine (STIGT) and combined steam...
-
Corrosion of evaporator tubes in low emission steam boilers
PublicationPurpose of this paper is to reveal the mechanisms of corrosion processes of outer surfaces of low-emission steam boiler evaporator tubes. Examinations were performed to find the reasons of different corrosion susceptibility of tubes situated at combustion chamber on various levels. Examinations were conducted on several segments of 57 x 5.0 mm evaporator tubes made of 16M (16Mo3) steel grade. Segments were taken from level of...
-
Exhaust gas temperature measurements in diagnostic examination of naval gas turbine engines. Part I: Steady-state processes
PublicationThe article presents a possible method of detecting failures in the flow section and supply system of a naval gas turbine engine based on the exhaust gas temperature measured behind the gas generator. This temperature is a basic diagnostic parameter use for evaluating the technical state of the turbine engine in operation, and is monitored during engine start-ups, accelerations and decelerations of rotor units, and steady-load...
-
The influence of the welding environment on the properties of Tekken joints made from S355J2C+N steel
PublicationThere are three main methods of underwater welding: dry, wet and intermediate between them, by using the local dry chamber. Due to low costs, the most common method is the wet welding with the use of covered electrodes. Water as a welding environment carries out a lot of problems. The first is limited visibility and instability of the welding arc. The biggest problem during underwater welding is high susceptibility to cold cracking,...
-
Enhancement of the Brayton cycle efficiency by water or steam utilization
PublicationIn the paper, thermodynamic analysis of two modifications of a Brayton cycle into enhancement cycles with water/steam injection are discussed. The first one deals with a STIG modified system with both interstage compressed air cooling and air heating (heat regeneration) before combustion chamber. The second one, mainly devoted to higher steam/air ratio, is connected with separate steam production in a HRSG. The analysis has been...
-
Power enhancement of the Brayton cycle by steam utilization
PublicationThe paper presents thermodynamic analysis of the gas-steam unit of the 65 MWe combined heat and power station. Numerical analyses of the station was performed for the nominal operation conditions determining the Brayton and combined cycle. Furthermore, steam utilization for the gas turbine propulsion in the Cheng cycle was analysed. In the considered modernization, steam generated in the heat recovery steam generator unit is directed...
-
Methodology for determining the elemental composition, as well as energy and ignition properties of the low-sulfur marine fuels
PublicationThe key metrological issue of substance and energy balance in research engines is the precise determination of the elemental composition of the applied fuel and its net calorific value. This makes it possible to calculate the amount of heat brought with the fuel into the combustion chamber, as well as the amount and gas composition of the exhaust. However, to fully assess the energy quality of the fuel used, its ignition properties...
-
Analysis of operations of combined STIG installation
PublicationSteam injection in gas turbines is interesting technology with good energetic and ecological properties of gas turbines. In these applications the heat of exhaust gases is used to produce steam, which is injected in the combustion chamber of a gas turbine. The steam injection increase the power and efficiency of the installation. there are some possibilities to increases the properties of STIG turbines, for example by meas of additional...
-
Experimental study of the multi-disc negative brake for a hydraulic motor
PublicationThis paper describes the methodology for experimental testing of a multi-disc brake. The construction of this brake was also present. The brake is dedicated to hydraulic motors with a small working volume. Experimental tests were carried out on a brake with plates immersed in oil and, for comparison, tests were carried out on a dry brake. As a result of the tests, the permissible torque (load) that is able to transfer the brake...
-
Thermodynamic Cycles of Air Microturbine Power Plants Working on Biomass Fuels
PublicationThe gas turbine engine is modified to work as an air turbine set which consists, in the simplest arrangement, of a compressor, a heat exchanger and a turbine. Air is a working medium for both: the compressor and the turbine. This kind of air turbine set can be applied in power plants working on biomass fuels. In this solution we can burn fuels of varying parameters in the external combustion chamber without any harmful effects...
-
A new model of fuel spray shape at early stage of injection in a marine Diesel engine
PublicationIn the cylinders of a marine diesel engine, self-ignition occurs in very shortly time after the fuel injection into the combustion chamber. Therefore, the paper present was to develop a model of diesel fuel spray for the early stage of fuel spray for in marine diesel engine. There were taken into consideration the main aspects technical such as nozzle diameter of marine engine injector and backpressure in combustion chamber. In...
-
Proposal of a Mobile Medical Waste Incinerator with Application of Automatic Waste Feeder and Heat Recovery System as a Novelty in Poland
PublicationThe paper presents and discusses the issues of medical waste (including hazardous ones) and the problems regarding their proper management in Poland. Inappropriate handling of infectious medical waste directly endangers human health and the environment. Infectious waste must be properly disposed of—in practice, the only method of their disposal available in Poland is a thermal treatment in the incinerators tailored for this purpose....
-
Exhaust gas temperature measurements in diagnostic examination of naval gas turbine engines. Part II. Unsteady processes
PublicationThe second part of the article presents the results of operating diagnostic tests of a two- and three-shaft engine with a separate power turbine during the start-up and acceleration of the rotor units. Attention was paid to key importance of the correctness of operation of the automatic engine load control system, the input for which, among other signals, is the rate of increase of the exhaust gas flow temperature. The article...
-
A Comparative Numerical Simulation Study of Turbulent Non-premixed CO/H2/N2 Syngas Jet Flames
PublicationIn the present work, numerical simulations of turbulent non-premixed syngas flame have been performed in Reynolds-Averaged Naver-Stokes turbulence approach using four turbulence-chemistry interaction models. To this aim, we used assumed beta PDF approach, Steady Laminar Flamelet model, Eddy Dissipation Concept and Partially Stirred Reactor model. Numerical results are compared and analysed with respect to two experiments from the...
-
PARAMETRIC ANALYSIS OF THE EFFICIENCY OF THE COMBINED GAS-STEAM TURBINE UNIT OF A HYBRID CYCLE FOR THE FPSO VESSEL
PublicationA thermal diagram of the combined gas‒steam turbine unit of a hybrid cycle, which is an energy complex consisting of a base gas turbine engine with a steam turbine heat recovery circuit and a steam-injected gas turbine operating with overexpansion, is proposed. A mathematical model of a power plant has been developed, taking into consideration the features of thermodynamic processes of simple, binary, and steam-injected...
-
An energetic analysis of a gas turbine with regenerative heating using turbine extraction at intermediate pressure - Brayton cycle advanced according to Szewalski's idea
PublicationIn this paper, a modification of a simple gas turbine into the Brayton cycle with regenerative heating, using turbine extraction at intermediate pressure, is presented. The main concept of the retrofitting is based on the transfer of heat from the turbine exhaust gases to the air entering the combustion chamber. The extracted gas transfers heat to air via the divided regenerative heat exchanger and after that is compressed and...
-
Power augmentation of PGE Gorzow's gas turbine by steam injection - thermodynamic overview
PublicationThe impact of steam injection upon a gas turbine and a combined power plant performance has been investigated. This article describes and summarizes possibilities of modification for current gas turbine in PGE Gorzow power plant into the Cheng cycle. Our modification deals with a thermal cycle, in which steam produced in a heat recovery steam generator is injected into the gas turbine's combustion chamber. It has been proved that...
-
Spawalność ferrytyczno-austenitycznej stali odpornej na korozję typu dupleks 2205 w warunkach podwodnych
PublicationPraca dotyczy problemów spawalności stali odpornej na korozję typu dupleks w warunkach spawania mokrego elektrodami otulonymi i lokalną komorą suchą. Całość rozprawy składa się z dwóch części. Część pierwsza to przegląd literatury, w którym omówiono główne problemy wynikające z przeniesienia procesu spawania pod wodę oraz sposoby minimalizowania negatywnego wpływu środowiska. Część druga jest częścią doświadczalną, zawiera tezę...
-
Thermodynamic Cycle Concepts for High-Efficiency Power Plans. Part A: Public Power Plants 60+
PublicationAn analysis was carried out for different thermodynamic cycles of power plants with air turbines. Variants with regeneration and different cogeneration systems were considered. In the paper, we propose a new modification of a gas turbine cycle with the combustion chamber at the turbine outlet. A special air by-pass system of the combustor was applied and, in this way, the efficiency of the turbine cycle was increased by a few points....
-
A comparative study of pentanol (C5 alcohol) and kerosene blends in terms of gas turbine engine performance and exhaust gas emission
PublicationThe growing demand for sustainable and clean energy sources provides the incentive for the development of alternative fuels. Simultaneously, the development of gas turbine technologies with flexible fuel supply systems enables the use of alternative non-fossil fuels that can play key roles in contributing to global efforts in meeting emissions targets. This paper presents the current state of knowledge on the production and potential...
-
Comparison analysis of selected nuclear power plants supplied with helium from high-temperature gas-cooled reactor
PublicationThe article presents results of efficiency calculations for two 560 MW nuclear cycles with high-temperature gas-cooled reactor (HTGR). An assumption was made that systems of this type can be used in so-called marine nuclear power plants. The first analysed system is the nuclear steam power plant. For the steam cycle, the efficiency calculations were performed with the code DIAGAR, which is dedicated for analysing this type of systems....
-
Proposal of a mobile medical waste incinerator with automatic waste feeder and heat recovery system
PublicationThe paper presents and discusses the issue of medical waste (including hazardous ones) and their proper management. Inappropriate handling of infectious medical waste directly endangers the human being health and the environment. Infectious waste must therefore be properly disposed of – one of the most commonly used methods is the thermal treatment in the incinerators tailored for this purpose. During designing an incinerator unit,...
-
Thermodynamic Cycle Concepts for High-Efficiency Power Plants. Part B: Prosumer and Distributed Power Industry
PublicationAn analysis was carried out for different thermodynamic cycles of power plants with air turbines. A new modification of a gas turbine cycle with the combustion chamber at the turbine outlet has been described in the paper. A special air by-pass system of the combustor was applied, and in this way, the efficiency of the turbine cycle was increased by a few points. The proposed cycle equipped with an effective heat exchanger could...
-
Thermodynamic modeling of combustion process of the internal combustion engines – an overview
PublicationThe mathematical description of combustion process in the internal combustion engines is a very difficult task, due to the variety of phenomena that occurring in the engine from the moment when the fuel-air mixture ignites up to the moment when intake and exhaust valves beginning open. Modeling of the combustion process plays an important role in the engine simulation, which allows to predict incylinder pressure during the combustion,...
-
Numerical analysis of high temperature minichannel heat exchanger for recuperative microturbine system
PublicationConsidering the development of energy sector, distributed small-scale power generation, e.g., gas micro-CHP, is attracting considerable interest. In such installations, the heat exchanger is one of the key components possessing a significant influence on overall performance. Most studies concentrate on units operating below 900C, which do not fulfil the requirements of gas micro-CHP. Therefore, there remains a challenge to design...
-
Selected aspects of performance of organic Rankine cycles incorporated into bioenergy with carbon capture and storage using gasification of sewage sludge
PublicationThe study aims to investigate the application of the Organic Rankine Cycle (ORC) in the bioenergy with carbon capture and storage (BECCS) using gasification of sewage sludge. The tool used in the investigation is the Aspen Plus software with REFPROP property methods for calculating fluid properties. The reason for this study is that a detailed analysis of the proposed BECCS process flow diagram indicates that a certain amount of...
-
Assessment, optimisation and working fluid comparison of organic rankine cycle combined with negative CO2 gas power plant system
PublicationThis study aims to investigate the application of the Organic Rankine Cycle (ORC) as an alternative to low-pressure expansion in the negative CO2 power plant (nCO2PP). The reason for this study is that a detailed analysis of nCO2PP indicates a certain amount of waste heat present in the exhaust gas from the high-to-intermediate pressure gas turbine. Some of this energy can be used by the application of the expansion in a low-pressure...
-
Identification of damages in the inlet air duct of a diesel engine based on exhaust gas temperature measurements
PublicationThe temperature of the exhaust gas of a diesel piston engine, measured in the characteristic control sections of its thermo-flow system, can be a valuable source of diagnostic information about the technical condition of the elements limiting the working spaces thus separated, including the turbocharging system, but also its fuel supply system and replacement of the medium. In standard marine engine measurement systems equipped...