Search results for: flat plate solar collector
-
Performance of the flat plate solar collector operated with water-Al2O3 nanofluid
PublicationThe paper discusses the effect of application of water-Al2O3 nanofluid, as a working fluid, on the efficiency of a flat plate solar collector. The mass concentration of nanoparticles was 0.1%, 0.2% and 0.4%. The tests were conducted for two values of radiation of about 1050 W/m2 and 400 W/m2, and volume flow rates of 60 l/h, 120 l/h and 170 l/h. The efficiency was calculated according to recommendations of the Polish Standard....
-
Performance of the flat plate solar collector operated with water-Al2O3 nanofluid
PublicationThis paper shows the experimental results of the performance a flat plate solar collector with water-Al2O3 nanofluid as a working fluid. The weight fractions of nanoparticles were 0.1%, 0.2% and 0.4%. The volume flow rate of nanofluid varied from 60 l/h to 170 l/h. The results show that application of nanofluids instead of pure water resulted in higher efficiency of the tested flat plate solar collector for given range of thermal...
-
Operational Properties Investigation of The Flat-Plate Solar Collector with Poliuretane Foam Insulation
Publication -
Significant Parameters Identification for Optimal Modelling of the Harp-Type Flat-Plate Solar Collector
Publication -
Metoda f-chart w zastosowaniu do projektu instalacji solarnej w budownictwie jednorodzinnym
PublicationW artykule przedstawiono algorytm obliczeń cieplnych związanych z konwersją promieniowania cieplnego oraz analizę efektów pracy instalacji solarnej przy użyciu metody korelacyjnej f-chart. Zaprezentowany algorytm obliczeń cieplnych oraz omówiona w artykule podstawowa odmiana metody f-chart zostały poparte przykładem obliczeniowym dla instalacji solarnej, która wykorzystywana jest do wspomagania układu przygotowania c.w. dla potrzeb...
-
PERFORMANCE OF THE PVT SOLAR COLLECTOR OPERATED WITH WATER –AL2O3 NANOFLUID
PublicationAn experimental investigation of the hybrid module photovoltaic panel -solar collector (PVT) cooled by water-Al2O3 nanofluids has been conducted. The weight fractions of the nanoparticles were 1% and 3%. Thermal efficiency, power efficiency and overall efficiency have been determined for artificial source of light and sunlight. No noticeable effect of the nanoparticle concentration on the overall efficiency of the PVT module has...
-
Performance of the PVT solar collector operated with water-Al2O3 nanofluid
PublicationAn experimental investigation of the hybrid module photovoltaic panel -solar collector (PVT) cooled by water-Al2O3 nanofluids has been conducted. The weight fractions of the nanoparticles were 1% and 3%. Thermal efficiency, power efficiency and overall efficiency have been determined for artificial source of light and sunlight. No noticeable effect of the nanoparticle concentration on the overall efficiency of the PVT module has...
-
Flow visualization and heat transfer investigations on the flat plate with streamwise pressure gradient
PublicationPaper presents experimental investigations results for film cooling on a flat plate. The main objective of the design is the streamwise pressure distribution on the flat plate as in the blade cascade. The transient and steady-state technique with liquid crystals for the surface temperature distribution with film cooling has been used in experiments in a low speed wind tunnel.
-
The low energy house using an air solar collector - a case study
PublicationCelem tego artykułu jest przedstawienie możliwości ogrzewania i chłodzenia domu jednorodzinnego przy wykorzystaniu słonecznych kolektorów powietrznych. W analizie uwzględniono dom energooszczędny, którego wskaźnik sezonowego zapotrzebowania na ciepło wynosi 40kWh/m2/a. Do obliczeń przyjęto kolektory powietrzne dostępne na rynku o powierzchni 60m2 i wydajności wynoszącej 70%. W analizowanym budynku występuje prawie pełne pokrycie...
-
Research into GTA automatic soft soldering technology for solar energy collector components
Publication -
Experimental investigations of prototype od solar collector on the rig equipped with artificial source of illumination
PublicationW pracy opisano badania eksperymentalne prowadzone w Katedrze Techniki Cieplnej Politechniki Gdańskiej, dotyczące prototypowego cieczowego kolektora słonecznego, wykonanego z organicznego tworzywa sztucznego. Badania cieplne przeprowadzono metodą porównanwczą, przy czym kolektorem odniesienia był kolektor słoneczny Aparel produkowany na rynku krajowym. W artykule opisano też stanowisko badawcze zaprojektowane i zbudowane jako moblina...
-
Investigations of hydraulic jump configured by a two phase air water jetimpinging on a flat plate.
PublicationPrzedstawiono wyniki badań eksperymentalnych uskoku hydraulicznego powstającego przy napływie strugi uderzającej na powierzchnię płaskiej płyty.
-
Michał Szydłowski dr hab. inż.
People -
Photovoltaic module temperature stabilization with the use of phase change materials
PublicationThe worldwide growth of photovoltaics (PVs) has formed an exponential curve for more than four decades. During this period of time, PVs have evolved from a pure niche market of small-scale applications towards becoming a mainstream electricity source. The influence of temperature on the electrical parameters of crystalline silicon solar cells and solar modules is well described in the literature. In order to diminish these effects,...
-
Laminated plates and shells - first ply failure analysis within 6-parameter shell theory
PublicationThis work describes Tsai-Wu and Hashin criteria modifications, dictated by nonlinear 6-parameter shell theory with asymmetric strain measures and drilling rotation. The material law is based on standard orthotropic elastic constants for a non-polar continuum, under plane state of stress. First ply failure loads of cylindrical panel subjected to pressure and flat compressed plate are estimated by means of Finite Element Analysis....
-
Multi-criteria Robot Selection Problem for an Automated Single-Sided Lapping System
PublicationFlat lapping is a crucial process in a number of precision manufacturing technologies. Its aim is to achieve extremely high flatness of the workpiece. Single-sided lapping machines have usually standard kinematic systems and are used in conjunction with conditioning rings, which are set properly be-tween the center and the periphery of the lapping plate. In this paper, instead of conventional single-side lapping machine, an automated...
-
Modeling of lapping plate wear and conditioning in single-sided lapping
PublicationIn order to achieve higher quality on worked surfaces with lower roughness, very high accuracy of shape and dimensions it is crucial to improve conventional finishing technologies and to develop new working principles. Single-sided lapping is one of the most effective planarization technologies and it is determined by a number of factors and boundary conditions. The most significant influence over a dimensional and profile accuracy,...
-
Linear impedance of Bi2VO5.5 glass-ceramic measured with impedance spectroscopy method at low temperature region
Open Research DataThe linear electrical properties of Bi2VO5.5 glass-ceramic prepared by traditional melt quenching technique was measured by impedance spectroscopy method.
-
Research on Tool Temperature Dependence on Lapping Grains Size
PublicationCommonly used as a finishing operation, lapping has been used for achieving ultra-high finishes and close tolerances between mating pieces. Its carried out by applying loose abrasive grains between work and lap surfaces, and causing a relative motion between them resulting in a finish of multi-directional lay. The grains activity (sliding and rolling) in the working gap causes not only the material removal but also the temperature...
-
The topography of Bi2VO5.5 ceramics prepared by melt-quenching technique was measured with confocal microscope
Open Research DataThe topography of Bi2VO5.5 ceramics prepared by melt-quenching technique was measured by confocal microscope.
-
The structure of lead-borate glasses containing nanocrystallites of iron oxides
Open Research DataThe structure of iron-doped glasses and glass-ceramics were studied. Glass samples of composition of xFe2O3–(100 − x)(B2O3–2PbO) (2.5 b x b 37, in mol%) were prepared by the conventional melt quenching technique. The melting was conducted in alumina crucibles at the temperature of 1523 K. The melts were poured on a preheated (573 K) brass plate and...
-
Linear impedance of strontium–borate glass measured with impedance spectroscopy method at low temperature region
Open Research DataThe linear electrcial properties of strontium–borate glass was measured by impedance spectroscopy method.
-
Linear impedance of Bi2VO5.5 glass-ceramic annealed at 423 K measured with impedance spectroscopy method at low temperature region
Open Research DataThe linear electrical properties of Bi2VO5.5 glass-ceramic annealed at 423 K prepared by traditional melt quenching technique was measured by impedance spectroscopy method.
-
Linear impedance of vanadate glasses containing BaTiO3
Open Research DataThe linear impedance of vanadate glasses doped with BaTiO3 was measured. Samples of the composition of x[BaO,TiO2]–(80 − x)V2O5–20Bi2O3 where x = 5, 10 and 15 in mol% were prepared by a conventional melt quenching technique. The melting was performed in alumina crucibles at the temperature of 1273 K–1373 K. The melts were poured on a preheated (573...
-
Topography of barium-vanadate glasses
Open Research DataThe topography of barium-vanadate glasses was measured. Samples of the composition of xBaO-(100-x)V2O5 where x= 30, 40 and 45 (in %mol) were prepared by the conventional melt quenching technique. Appropriate amounts of reagents: BaO (≥99.9%, P.P.H STANLAB Sp.J.) and V2O5 (≥99.9%, POCH) were thoroughly mixed in an agate mortar. The melting was performed...
-
Overheating of underground power cable line due to its partial exposition to solar radiation
PublicationCurrent-carrying capacity of underground power cable lines depends, among others, on thermal resistivity of the soil and cables layout: trefoil formation, flat formation with or without spacing. If conditions for heat transfer in the ground are favorable, the current-carrying capacity is relatively high. Therefore, it generates risk of the power cables overheating, if part of the cable line is located vertically in the air, to...
-
Hydrothermal Cobalt Doping of Titanium Dioxide Nanotubes towards Photoanode Activity Enhancement
PublicationDoping and modification of TiO2 nanotubes were carried out using the hydrothermal method. The introduction of small amounts of cobalt (0.1 at %) into the structure of anatase caused an increase in the absorption of light in the visible spectrum, changes in the position of the flat band potential, a decrease in the threshold potential of water oxidation in the dark, and a significant increase in the anode photocurrent. The material...
-
Linear impedance of strontium–borate glass measured with impedance spectroscopy method at high temperature region
Open Research DataThe linear electrcial properties of strontium–borate glass was measured by impedance spectroscopy method.
-
Electrical properties of lead-borate glasses and glass-ceramics containing iron ions
Open Research DataElectrical properties were studied for borate-lead glasses and glass-ceramics doped with iron ions. Glass samples of composition of xFe2O3–(100 − x)(B2O3–2PbO) (2.5 b x b 37, in mol%) were prepared by the conventional melt quenching technique. The melting was conducted in alumina crucibles at the temperature of 1523 K. The melts were poured on a preheated...
-
Dielectric properties of barium-vanadate glasses
Open Research DataThe linear impedance of barium-vanadate glasses was measured. Samples of the composition of xBaO-(100-x)V2O5 where x= 30, 40 and 45 (in %mol) were prepared by the conventional melt quenching technique. Appropriate amounts of reagents: BaO (≥99.9%, P.P.H STANLAB Sp.J.) and V2O5 (≥99.9%, POCH) were thoroughly mixed in an agate mortar. The melting was...
-
Linear impedance of vanadate glass-ceramics containing BaTiO3
Open Research DataThe linear impedance of vanadate glass-ceramics containing BaTiO3 was measured. Samples of the composition of x[BaO,TiO2]–(80 − x)V2O5–20Bi2O3 where x = 5, 10 and 15 in mol% were prepared by a conventional melt quenching technique. The melting was performed in alumina crucibles at the temperature of 1273 K–1373 K. The melts were poured on a preheated...
-
The topography of as-quenched and heat treated 58(2Bi2O3-V2O5)-42SrB4O7 glasses measured with confocal microscope
Open Research DataThe topography of as-quenched and heat treated 58(2Bi2O3-V2O5)-42SrB4O7 glasses measured with confocal microscope.
-
Linear impedance of 58(2Bi2O3-V2O5)-42SrB4O7 glass measured with impedance spectroscopy method at low temperature region
Open Research DataThe linear electrcial properties of 58(2Bi2O3-V2O5)-42SrB4O7 glass was measured by impedance spectroscopy method.
-
Linear impedance of 5(2Bi2O3-V2O5)-95SrB4O7 glass measured with impedance spectroscopy method at low temperature region
Open Research DataThe linear electrcial properties of 5(2Bi2O3-V2O5)-95SrB4O7 glass was measured by impedance spectroscopy method.
-
Linear impedance of 50(2Bi2O3-V2O5)-50SrB4O7 glass measured with impedance spectroscopy method at low temperature region
Open Research DataThe linear electrcial properties of 50(2Bi2O3-V2O5)-50SrB4O7 glass was measured by impedance spectroscopy method.
-
Linear impedance as a function of A.C. voltage for 50(2Bi2O3-V2O5)-50SrB4O7 glass measured with impedance spectroscopy method
Open Research DataThe linear electrcial properties as a function of A.C. voltage for 50(2Bi2O3-V2O5)-50SrB4O7 glass was measured by impedance spectroscopy method.
-
Multi-layered mineral glass units used as viewport elements of underwater ship structures
PublicationIn the paper, Authors deals with viewport elements of underwater marine constructions. If a single-plate viewport constructions are considered, big thicknesses of the glass plate are required to resist the pressure. To build the viewports from the commercially accessible glass panes, multi-layered glass units are proposed in the paper. Numerical calculations are presented, summarized and compared with experimental tests. Focusing...
-
The structure of 50(2Bi2O3-V2O5)-50SrB4O7 measured with X-ray diffraction method during heating
Open Research DataThe structure changes of 50(2Bi2O3-V2O5)-50SrB4O7 glass occurred during increase in temperature was measured by XRD.
-
Linear impedance of 50(2Bi2O3-V2O5)-50SrB4O7 glass measured with impedance spectroscopy method at high temperature region
Open Research DataThe linear electrcial properties of 50(2Bi2O3-V2O5)-50SrB4O7 glass was measured by impedance spectroscopy method.
-
The morphology of as-quenched and heat treated 58(2Bi2O3-V2O5)-42SrB4O7 glasses measured with AFM
Open Research DataThe morphology of as-quenched and heat treated 58(2Bi2O3-V2O5)-42SrB4O7 glasses was measured with the use of atomic force microscope.
-
Flow distribution and heat transfer in minigap and minichannel heat exchangers during flow boiling
PublicationThe topic of boiling heat transfer in miniscale geometries has focused the ever increasing interest of researchers in recent years. However, most of the works are related to mini- and microchannels and much less to minigaps. Meanwhile, minigaps allow for more comprehensive experimental studies, i.e. flow visualisations due to the flat, two-dimensional configuration of the flow. The results of the experimental investigations of...
-
Koncepcja zdalnego sterowania i monitoringu urządzeń trakcyjnych z wykorzystaniem technologii teleinformatycznych
PublicationAdvancement in wireless communication enables engineers to apply sophisticated and relatively inexpensive technologies in new fields of industry, which were previously designated solely to wire-based solutions. One of those fields is railway transportation system. In effect of a high reliability and safety demands, this area was resistive to new technologies. Nowadays, increased security and reliability of wireless sensor networks...
-
Topography of iron-phosphate glasses doped with niobium and titanium tested by confocal microscope
Open Research DataThe topography of phosphate-iron glasses containing niobium and titanium were investigated with the use of confocal miscroscope. Glass samples of the composition of 35P2O5-30Fe2O3-35Nb2O5, 35P2O5-30Fe2O3-27.5Nb2O5-7.5TiO2 and 35P2O5-30Fe2O3-20Nb2O5-15TiO2 (in %mol) were prepared by the conventional melt quenching technique. Appropriate amounts of reagents...
-
Linear impedance of 58(2Bi2O3-V2O5)-42SrB4O7 glass heat-treated for 3 hours at 693 K, measured with impedance spectroscopy method at low temperature region
Open Research DataThe linear electrcial properties of partially crystallized 58(2Bi2O3-V2O5)-42SrB4O7 glass was measured by impedance spectroscopy method.
-
Linear impedance of 5(2Bi2O3-V2O5)-95SrB4O7 glass measured with impedance spectroscopy method at high temperature region
Open Research DataThe linear electrcial properties of 5(2Bi2O3-V2O5)-95SrB4O7 glass was measured by impedance spectroscopy method.
-
Linear impedance of 58(2Bi2O3-V2O5)-42SrB4O7 glass heat-treated for 10 hours at 693 K, measured with impedance spectroscopy method at low temperature region
Open Research DataThe linear electrcial properties of partially crystallized 58(2Bi2O3-V2O5)-42SrB4O7 glass was measured by impedance spectroscopy method.
-
Linear impedance as a function of A.C. voltage for 50(2Bi2O3-V2O5)-50SrB4O7 glass heat treated at 693 K measured with impedance spectroscopy method at 273 K
Open Research DataThe linear electrcial properties as a function of A.C. voltage for 50(2Bi2O3-V2O5)-50SrB4O7 glass heat treated at 693 K was measured by impedance spectroscopy method.
-
Linear impedance of 35P2O5-30Fe2O3-20Nb2O5-15TiO2
Open Research DataThe electrical properties of phosphate-iron glasses containing niobium and titanium were investigated. Glass samples of the composition of 35P2O5-30Fe2O3-20Nb2O5-15TiO2 (in %mol) were prepared by the conventional melt quenching technique. Appropriate amounts of reagents ((NH4)2HPO4 (≥99.9%, POCH), Fe2O3 (≥99.9%, POCH), Nb2O5 (≥99.9%, PLUKA AG) and TiO2...
-
Linear impedance of 35P2O5-30Fe2O3-27.5Nb2O5-7.5TiO2
Open Research DataThe electrical properties of phosphate-iron glasses containing niobium and titanium were investigated. Glass samples of the composition of 35P2O5-30Fe2O3-27.5Nb2O5-7.5TiO2 (in %mol) were prepared by the conventional melt quenching technique. Appropriate amounts of reagents ((NH4)2HPO4 (≥99.9%, POCH), Fe2O3 (≥99.9%, POCH), Nb2O5 (≥99.9%, PLUKA AG) and...
-
Linear impedance of 35P2O5-30Fe2O3-35Nb2O5
Open Research DataThe electrical properties of phosphate-iron glasses containing niobium were investigated. Glass samples of the composition of 35P2O5-30Fe2O3-35Nb2O5 (in %mol) were prepared by the conventional melt quenching technique. Appropriate amounts of reagents ((NH4)2HPO4 (≥99.9%, POCH), Fe2O3 (≥99.9%, POCH), Nb2O5 (≥99.9%, PLUKA AG) and TiO2 (≥99.9%, anatase...