displaying 1000 best results Help
Search results for: EXPERIMENT
-
Water-lubricated stern tube bearing - experimental and theoretical investigations of thermal effects
PublicationThe paper presents research results of thermal phenomena accompanying operation of a water-lubricated stern tube bearing with axial grooves. Experimental tests revealed, that intensity of forced axial flow has strong influence on bush temperature. Numerical simulations focused on investigation of the thermal phenomena under operation of water-lubricated journal bearing showed, that restricted axial flow promotes backflow of the...
-
Theoretical and experimental study on scattering of low-energy electrons by dimethyl and diethyl ethers
PublicationWe report a joint theoretical and experimental investigation on low-energy electron scattering by dimethyl and diethyl ethers. The experimental elastic differential cross sections were measured at impact energies from 1 eV up to 30 eV and scattering angle range of 10◦ to 130◦. Theoretical elastic differential, integral and momentum-transfer cross sections are calculated at impact energies up to 30 eV, employing the Schwinger multichannel...
-
Experimental and numerical investigations of ultimate strength of imperfect stiffened plates of different slenderness
PublicationThe objective of this study is to analyse the behaviour of compressed stiffened plates of different slenderness using experimental and numerical methods. The presented results are part of a long-term project to investigate the ultimate strength of geometrically imperfect structures subjected to different degradation phenomena, including corrosion degradation and locked cracks. Several specimens were subjected to a uniaxial compressive...
-
Experimental and numerical investigations on RC beams with stirrups scaled along height or length.
PublicationBelki żelbetowe (RC) ze zbrojeniem poprzecznym (strzemiona) poddane czteropunktowemu zginaniu zostały zbadane eksperymentalnie i numerycznie. Belki były skalowane wzdłuż wysokości lub długości. Były przezbrojone, aby uniknąć płynięcia zbrojenia podłużnego. W pierwszej kolejności przeprowadzono badania laboratoryjne na belkach żelbetowych ze strzemionami. Ze względu na brak podobieństwa geometrycznego zaobserwowano dwa odrębne tryby...
-
Experimental and numerical investigation of mercury removal from flue gas by sorbent polymer composite
PublicationThis paper presents an experimental and numerical investigation of the performance of a sorbent polymer composite (SPC) material used for removing mercury from the flue gases in a full-scale industrial installation. The investigated material is an attractive alternative to activated carbon, which is commonly used for this purpose. While the application of the SPC is characterized by high capital expenditures, this technology offers...
-
Shaking table experimental study on damage mechanism of the disconnecting switch under seismic excitation
PublicationThe efficiency of the energetic network is a very import safety issue in the region experienced by the earthquake. High voltage disconnecting switches are important elements of the energetic infrastructure used to separate electric circuits (i.e. during repairs), which should not be damaged remaining fully operational. The aim of the paper is to show the results of the shaking table experimental investigation focused on damage...
-
Joint experimental and theoretical study on electron scattering from titanium tetrachloride (TiCl4) molecule
PublicationAbsolute grand-total cross section for electron scattering from titanium tetrachloride, TiCl4, molecule was measured at electron-impact energies ranging from 0.3 to 300 eV, in the linear electron-transmission experiment. The elastic integral, differential, momentum transfer, and total ionization cross sections for TiCl4 molecule were also calculated for low and intermediate collisional energies at the level of various theories. The...
-
CLINICAL AND EXPERIMENTAL MEDICINE
Journals -
CLINICAL AND EXPERIMENTAL DERMATOLOGY
Journals -
ENVIRONMENTAL AND EXPERIMENTAL BOTANY
Journals -
Output voltage, current and DC-link voltages under SVPWM, experimental results
Open Research DataThe dataset contains the experimental results of the project: A universal algorithm of space vector pulse width modulation for three-level three and multi-phase NPC inverters with DC-link voltage balancing. The output line-to-line voltage, output current and DC-link voltages were included. The comparison studies between proposed Space Vector Pulse-Width...
-
Output voltage, current and DC-link voltages under SPWM, experimental results
Open Research DataThe dataset contains the experimental results of the project: A universal algorithm of space vector pulse width modulation for three-level three and multi-phase NPC inverters with DC-link voltage balancing. The output line-to-line voltage, output current and DC-link voltages were included. The Carrier-Based Pulse-Width Modulation (CBPWM) technique was...
-
The ab initio and experimental study of the spectroscopic and magnetic properties of Ho(III)-EDTA
Open Research DataIn this dataset, the ab initio calculations of the electronic structure and the magnetic properties are discussed in the context of the experimental data for the Ho–EDTA complex. In the calculations different models of the cluster have been applied to examine the influence of various parts of the environment of the Ho(III)-EDTA complex on its properties....
-
Experimental investigation of the weight averaging of pulse frequency modulated sensor output signal
Open Research DataThe research aims to practically verify the results of theoretical analysis and simulations of the efficiency of weight averaging of pulse frequency modulated signal. For this purpose, a suitable test stand was built, and the control software in the LabVIEW environment was prepared. Then, a series of experiments were carried out to process and analyze...
-
Experimental investigation and process parameter optimization of sheet metal bending by line heating method
PublicationThe present study is concerned with the experimental investigation of sheet metal deforming by line heating method that incorporates the combined effect of traverse speed of the torch, thickness of the sheet metal, and the number of passes of the torch. For the numerical analysis of metal bending by line heating, the
-
Experimental and numerical study on deformed steel columns subjected to impact load during earthquakes
PublicationThe soft-storey failure is one of the most typical types of damage observed in buildings during earthquakes. The failure of an upper soft storey of a structure results in large impact load acting on the lower floors and if the resistance of the structural members of the lower storeys is not sufficient it may further lead to progressive collapse of the whole building. The aim of the present paper is to investigate the dynamic behaviour...
-
Mechanics of mesh implanted into abdominal wall under repetitive load. Experimental and numerical study
PublicationThere are a number of papers discussing medical and mechanical aspects of ventral hernia management. Despite intensive work on the problem understanding, recurrences of the sickness still happen too often. For that reason new aspects of the problem must be considered. In this paper, a change in the abdominal implant’s stiffness is discussed, which is caused by cyclic loading. Such loading influence abdominal implant e.g. while...
-
Workshop on Algorithm Engineering and Experiments
Conferences -
Experimental investigations on adiabatic frictional pressure drops of R134a during flow in 5mm diameter channel
PublicationThe article presents detailed two-phase adiabatic pressure drops data for refrigerant R134a at a saturation pressure of 5.5 bar corresponding to the saturation temperature of 19.4 °C. Study cases have been set for a mass flux varying from 100 to 500 kg/m2 s. The frictional pressure drop was characterized for the refrigerant R134a, for vapor qualities ranging from 0 to 1. Long-time thermal stability of test facility allowed to gather...
-
Stability and bearing capacity of arch-shaped corrugated shell elements: experimental and numerical study
Publication -
Solubility advantage of sulfanilamide and sulfacetamide in natural deep eutectic systems: experimental and theoretical investigations
PublicationObjective: The aim of this study was to explore the possibility of using natural deep eutectic solvents (NADES) as solvation media for enhancement of solubility of sulfonamides, as well as gaining some thermodynamic characteristics of the analyzed systems. Significance: Low solubility of many active pharmaceutical ingredients is a well-recognized difficulty in pharmaceutical industry, hence the need for different strategies addressing...
-
Ab initio and experimental studies of polarization and polarization related fields in nitrides and nitride structures
Publication -
Does Human Potentiality Affect IT Professionals’ Organizational Behavior? An Experimental Study in Poland and Germany
Publication -
Experimental and numerical study on damage detection in an L-joint using guided wave propagation
Publication -
Are firefighters able to perform blind endotracheal intubation via LMA Fastrach? An experimental study
Publication -
Experimental and numerical study on damage detection in an L-joint using guided wave propagation
PublicationW pracy zaprezentowano metodę wykrywania i lokalizacji uszkodzeń w konstrukcji ramowej za pomocą podłużnych i poprzecznych fal sprężystych. Przeprowadzono badania numerczyne i eksperymentalne na modelu bez uszkodzenia oraz na modelu z wsprowadzonym nacięciem. Do modelowania zastosowano metodę elementów spektralnych. W pracy przedstawiono sformułowanie nowego element spektralnego dla ram płaskich bazującego na teorii pręta Mindlina...
-
Water-lubricated bearings of ship propeller shafts - problems, experimental tests and theoretical investigations
PublicationW pracy przedstawiono problemy związane z projektowaniem, montażem i ekspolatcją smarowanych wodą łożysk okrętowych wałów głównych.Przedstawiono wyniki prowadzonych prac badawczych ekperymntalnych i obliczeń.
-
Large-scale Rowe cell experimental study on coefficient of consolidation of coal mine tailings
Publication -
Experimental investigation of the flow pattern and wall pressure distribution in a silo with double-cone insert
PublicationArtykuł opisuje przeprowadzone badania przepływów silosowych i naporu materiałów sypkich podczas napełniania i opróżniania silosu o średnicy 2.5 m wyposażonego we wkładkę "podwójny stożek". Badania przeprowadzane były w Instytucie Badawczym Tel-Tek w Norwegii. Materiałem użytym był suchy piasek. Napór na ścianę mierzony był bezpośrednio za pomocą 10 czujników wbudowanych w ścianę. Badania eksperymentalne pokazały duży wpływ wkładki...
-
The experimental study of compaction parameters and elastic after-effect of fine fraction raw materials
Publication -
Experimental determination of critical conditions for hydrogen-air detonation propagation in partially confined geometry
Publication -
Neuro-wavelet damage detection technique in beam, plate and shell structures with experimental validation
PublicationNiniejsza praca poświęcona jest technice diagnostyki konstrukcji bazującej na transfor-macie falkowej oraz sztucznych sieciach neuronowych (tzw. system neuro-wavelet). Zastosowanie analizy falkowej pozwala na lokalizację uszkodzeń wymagającą mini-malnej ilości danych wejściowych. W tym celu niezbędna jest tylko odpowiedź kon-strukcji pomierzona w wielu punktach. Poprawę efektywności lokalizacji zniszczeń uzyskano poprzez użycie...
-
SIMULATION AND EXPERIMENTAL RESEARCH OF CLAW POLE MACHINE WITH A HYBRID EXCITATION AND LAMINATED ROTOR CORE
Publication -
An Experimental Study of Emission and Combustion Characteristics of Marine Diesel Engine with Fuel Injector Malfunctions
Publication -
Experimental Evaluation of the Agent-Based Population Learning Algorithm for the Cluster-Based Instance Selection
Publication -
An experimental study of emission and combustion characteristics of marine diesel engine with fuel pump malfunctions
Publication -
Experimental evaluation of high frequency side scan sonar as object search and identification tool
PublicationPraca prezentuje wyniki badań laboratoryjnych sonaru bocznego jako narzędzia dla pojazdu podwodnego, służącego do poszukiwań i identyfikacji obiektów leżących na dnie, w bliskich odległościach.
-
Experimental frequency-domain characterization of fundamental guided mode parameters in coupled coplanar waveguide
PublicationW pracy przedstawiono metodę wyznaczania współczynnika propagacji oraz impedancji charakterystycznej rodzajów podstawowych w strukturze sprzężonych linii koplanarnych. Metoda, oparta o wykorzystanie specjalnych struktur pobudzających oraz klasyczne pomiary w dziedzinie częstotliwości przy pomocy wektorowego analizatora sieci wykazała przydatność do wyznaczania zależnych od częstotliwości parametrów struktury.
-
Design and experimental evaluation of pod propulsor models for a large self-propelled ship model.
PublicationArtykuł przedstawia serię hydrodynamicznych badań swobodnych dwóch modeli pędnika podowego. Pędniki zostały zaprojektowane i zbudowane specjalnie dla dwóch wersji dużego modelu okrętu z własnym napędem, przeznaczonego do eksperymentów manewrowych. Jedna wersja jest napędzana pojedyńczym pędnikiem, druga jest wyposażona w dwa pędniki. Oba modele podów były badane w kanale obiegowym. Celem eksperymentu były pomiary sześciu składowych...
-
Experimental determination of impact stiffness parameters for the non-linear viscoelastic model of pounding force
PublicationNieliniowy model lepko-sprężysty umożliwia dokładną symulację siły zderzenia w czasie oraz symulację odpowiedzi konstrukcji podatnej na zderzanie podczas trzęsień ziemi. Celem tego artykułu jest eksperymentalne wyznaczenie wartości współczynnika sztywności zderzenia jako parametru tegoż modelu.
-
Experimental investigations of prototype od solar collector on the rig equipped with artificial source of illumination
PublicationW pracy opisano badania eksperymentalne prowadzone w Katedrze Techniki Cieplnej Politechniki Gdańskiej, dotyczące prototypowego cieczowego kolektora słonecznego, wykonanego z organicznego tworzywa sztucznego. Badania cieplne przeprowadzono metodą porównanwczą, przy czym kolektorem odniesienia był kolektor słoneczny Aparel produkowany na rynku krajowym. W artykule opisano też stanowisko badawcze zaprojektowane i zbudowane jako moblina...
-
Prediction of the fatigue lifetime of PUR structural elements using a combined experimental-numerical approach
PublicationThis paper presents a method for estimating the fatigue life of polyurethane elastomeric components. A rubber replacement - polyurethane of hardness 80ShA commonly used in vibration damping systems, for example, in motor vehicle suspensions, was used for the study. A metal-rubber bushing component was selected for analysis, and numerical analysis was carried out along with a fatigue model proposal based on a modification of the...
-
Experimental investigation on heat pipes supported by soy wax and lauric acid for electronics cooling
PublicationThis paper presents an experimental study of heat pipes for electronics cooling that were supported by energy storage materials (i.e. phase change materials - PCMs) coated at the adiabatic section. The PCMs utilized included two materials, namely lauric acid and soy wax, the latter being considered as a more cost-effective alternative. The study focused on three different powers: 20 W, 25 W, and 30 W. Both heating, cooling, and...
-
Dataset Related Experimental Investigation of Chess Position Evaluation Using a Deep Neural Network
PublicationThe idea of training Articial Neural Networks to evaluate chess positions has been widely explored in the last ten years. In this paper we investigated dataset impact on chess position evaluation. We created two datasets with over 1.6 million unique chess positions each. In one of those we also included randomly generated positions resulting from consideration of potentially unpredictable chess moves. Each position was evaluated...
-
Experimental and numerical analysis of the pyrolysis dynamics of a single wood particle: presentation of the radiographic technique
PublicationPyrolysis is an oxygen-free process for the thermal decomposition of raw materials. The heat conduction and flow of pyrolysis products (i.e., the gas fraction and liquid vapour generated during pyrolysis) influence the process and products. In this work, the influence of the orientation of wooden particle fibres with respect to the direction of the heat source on the dynamics of the process was investigated, where there were two...
-
Experimental comparison of the transition speed of a hydrodynamic journal bearing lubricated with oil and magnetorheological fluid
PublicationA journal bearing test bench is used to find the transition speed between the hydrodynamic and mixed lubrication regimes for a modified magnetorheological (MR) fluid. It is shown that the transition speed of the bearing can be reduced by applying a local magnetic field near minimum film when it is lubricated with the MR fluid, and that this will only marginally increase friction. The lubricating performance of the MR fluid is compared...
-
Application in circular sawing machines of the experimental results of investigations of the chip removing system operation
PublicationThe experimental results of the chip removing system operation are presented. The main aim of them was to optimize suction system of the panel saw Fx3 and its follower Fx550. The attention was focused on the upper casing, which was the part of removing system. Within the framework of the work a systematic experimental study of pressure distribution in the casing during operation of the selected rotational speed of saw blade with...
-
Impact of the inclination angle of the condenser with refrigerant R410A on heat transfer coefficient – experimental study
PublicationIn the paper the authors present results of a laboratory test of the condenser with refrigerant R410A. The effect of the inclination of this condenser on the heat transfer coefficient value has been considered. The test has proved that there is an optimal inclination angle of the condenser which gives maximal value of this coefficient.
-
ENERGY SAVINGS BY APPLICATION OF SUPERCAPACITOR STORAGE IN TROLLEYBUS SUPPLYING STATION – ANALYSIS OF EXPERIMENTAL RESULTS
PublicationIn 2011–2013, stationary supercapacitor storage developed by the Electrotechnical Institute in Warsaw was put into trial operation in the trolleybus substation “Północna” (North) located in Gdynia. The article presents the results recorded during supercapacitor storage operation and discusses the impact of the storage on energy consumption savings. Guidelines for selecting a location for stationary supercapacitor storage...
-
Experimental and numerical study on polymer element used for reduction of temporary steel grandstand vibrations
PublicationThe purpose of the paper is to analyse the effectiveness of a polymer damper in reduction of a temporary steel grandstand vibrations through the experimental and numerical study. The damper considered in the investigation is constructed out of two L-shape steel members bonded with polymer mass of high damping properties. The element has been installed as a diagonal one at the back part of the structure. The method has been compared...