displaying 1000 best results Help
Search results for: heat affected zone
-
CO2 capture through direct-contact condensation in a spray ejector condenser and T- junction separator
PublicationThe design principle underlying the steam condensation and CO2 purification in a gas power plant with a focus on reducing CO2 emissions encompasses the deployment of a spray ejector condenser (SEC) and separator. This innovative system facilitates direct-contact condensation of steam with non-condensable gas (CO2) by inter acting with a spray of subcooled water, seamlessly integrated with a T-junction separator mechanism aimed...
-
Role of bead sequence in underwater welding
PublicationThis paper presents examinations of the role of the bead sequence in underwater welding. Two specimens of wet welded layers made by covered electrodes with the use of normalized S355G10+N steel were welded by a reasonable bead sequence. For each specimen, metallographic macro- and micro-scopic tests were done. Then, Vickers HV10 hardness measurements were conducted for each pad weld in the welded layer. The results show that welding...
-
Nonlinear impedance of 58(2Bi2O3-V2O5)-42SrB4O7 glass heat-treated for 3 hours at 693 K, measured with impedance spectroscopy method at low temperature region
Open Research DataThe nonlinear electrcial properties of partially crystallized 58(2Bi2O3-V2O5)-42SrB4O7 glass was measured by impedance spectroscopy method.
-
Nonlinear impedance of 58(2Bi2O3-V2O5)-42SrB4O7 glass heat-treated for 10 hours at 693 K, measured with impedance spectroscopy method at low temperature region
Open Research DataThe nonlinear electrcial properties of partially crystallized 58(2Bi2O3-V2O5)-42SrB4O7 glass was measured by impedance spectroscopy method.
-
Bartosz Dawidowicz dr inż.
PeopleHe graduated from the Faculty of Mechanical Engineering at Gdańsk University of Technology MSc Eng. - Faculty of Mechanical Engineering, Gdansk University of Technology: specialization: Machines and Equipment of Food Industry (2000)PhD - Faculty of Mechanical Engineering, Gdansk University of Technology, discipline: construction and operation of machines, specialization: heat transfer (2008) Main areas of scientific activity related...
-
The effect of pressure on heat transfer during pool boiling of water-Al2O3 and water-Cu nanofluids on stainless steel smooth tube
PublicationPrzedstawiono wyniki badań eksperymentalnych wrzenia nanocieczy woda-Al2O3 i woda-Cu o koncentracjach nanocząstek 0.01%, 0.1% oraz 1% przy ciśnieniu absolutnym 10 kPa, 100 kPa oraz 200k Pa.
-
Particle rotation effects in Cosserat-Maxwell boundary layer flow with non-Fourier heat transfer using a new novel approach
Publication -
The effect of pressure on heat transfer during pool boiling of water-Al2O3 and water-Cu nanofluids on stainless steel smooth tubes
PublicationPrzedstawiono wyniki badań eksperymentalnych wrzenia nanocieczy woda-Al2O3 i woda-Cu o koncentracjach nanocząstek 0.01%, 0.1% oraz 1% przy ciśnieniu absolutnym 10 kPa, 100 kPa oraz 200k Pa.
-
Assessment of heat stress in a hot environment using the WBGTeff index according to the standard PN-EN ISO 7243:2018-01
Publication -
Experimental verification of the theoretical modelof heat transfer between a liquid layer formed by a two-phase impinging jet and a solid surface
PublicationW pracy przedstawiono eksperymentalną weryfikacje modelu teoretycznego wymiany ciepła pomiędzy warstwą wody a stałą powierzchnią. Warstwa cieczy powstała z uderzającej o powierzchnię dwufazowej strugi uderzającej
-
Comparative Study on Effects of Thermal Gradient Direction on Heat Exchange between a Pure Fluid and a Nanofluid: Employing Finite Volume Method
Publication -
Galerkin finite element analysis of Darcy–Brinkman–Forchheimer natural convective flow in conical annular enclosure with discrete heat sources
Publication -
THREE-DIMENSIONAL NUMERICAL INVESTIGATION OF MHD NANOFLUID CONVECTIVE HEAT TRANSFER INSIDE A CUBIC POROUS CONTAINER WITH CORRUGATED BOTTOM WALL
Publication -
Effect of heat treatment on the diffusion intermixing and structure of the Cu thin film on Si (111) substrate: a molecular dynamics simulation study
PublicationThis work is devoted to the study of the diffusion process at the interface between copper films with a thickness of 2, 3, 4, 7 and 10 atomic monolayers and silicon substrate by molecular dynamics simulation method. For this purpose, the variation of the concentration of copper and silicon along the perpendicular direction to the interface was investigated. An analysis of the density profile along this direction made it possible...
-
An analysis of the possibilities of increasing the production of electrical energy during the summer season by heat-generation back pressure turbine power units.
PublicationZbadano możliwości podniesienia mocy elektrycznej produkowanej przez przeciwprężne bloki ciepłownicze w sezonie letnim. Zbadano jedną z możliwości polegającą na dochładzaniu wody sieciowej powracającej z aglomeracji miejskiej. Zwrócono uwagę na aspekty techniczne, ekonomiczne i ekologiczne rozważanego rozwiązania.
-
Curved Surface Minijet Impingement Phenomena Analysed with ζ-f Turbulence Model
PublicationThe jet impingement phenomenon plays an important role among the heat transfer intensification methods. Very often its application and analyses refer to simple flat surfaces, while there is a lack of information in the literature for cases addressing curved surfaces. In the present work, the single jet impingement on the non-flat (concave and convex) surface is studied for a wide range of geometries, which originate from the mini-jet...
-
Pool Boiling of Water–Al2O3 and Water–Cu Nanofluids Outside Porous Coated Tubes
PublicationThis paper deals with pool boiling ofwater–Al2O3 and water–Cu nanofluids on porous coated, horizontal tubes. Commercially available stainless-steel tubes having 10 mm outside diameter and 0.6 mm wall thickness were used to fabricate a test heater. Aluminum porous coatings 0.15 mm thick with porosity of about 40% were produced by plasma spraying. A smooth tube served as a reference tube. The experiments were conducted under different...
-
Effects of FSW Tool Plunge Depth on Properties of an Al-Mg-Si Alloy T-Joint: Thermomechanical Modeling and Experimental Evaluation
PublicationOne of the main challenging issues in friction stir welding (FSW) of stiffened structures is maximizing skin and flange mixing. Among the various parameters in FSW that can affect the quality of mixing between skin and flange is tool plunge depth (TPD). In this research, the effects of TPD during FSW of an Al-Mg-Si alloy T-joint are investigated. The computational fluid dynamics (CFD) method can help understand TPD effects on FSW...
-
Atmospheric Pressure Plasma-Mediated Synthesis of Platinum Nanoparticles Stabilized by Poly(vinylpyrrolidone) with Application in Heat Management Systems for Internal Combustion Chambers
Publication -
Some Problems of Heat and Power Distributed Generation Control = Wybrane zagadnienia sterowania automatycznego rozproszonego wytwarzania energii elektrycznej i ciepła
PublicationRozproszone wytwarzanie energii elektrycznej wnosi pewne problemy z punktu widzenia współpracy z zewnętrznym systemem elektroenergetycznym. Wynikają one z koniecznością zapewnienia należytej jakości energii elektrycznej (częstotliwości i napięcia). Są one tym większe im większą moc ma tego rodzaju źródło energii elektrycznej oraz im jest większa zmienność jego mocy. Z tego powodu największe trudności regulacyjne sprawiają farmy...
-
Passive Methods in Heat Transport, W/P, DaPE, sem.5, zimowy 22/23, (PMiHT, W/P, zima 22/23)
e-Learning Courses -
Analyses of the effect of tooth rake angle and friction conditions upon the shear angle in the cutting zone during wood sawing. - [Chapter III]W : Wood machining and processing - product and tooling quality development
PublicationW pracy przedstawiono analizy wpływu wartości kąta natarcia piły i warunków tarcia na zmiany kata ścinania w strefie skrawania podczas przecinania drewna. W obliczeniach numerycznych kąta ścinania wykorzystywano podejście oparte o współczesną mechanikę pękania. Obliczenia prowadzono dla próbek z drewna dębu, jesionu po modyfikacji termicznej jak również dla drewna niemodyfikowanego. Dla drewna jesionowego modyfikowanego termicznie...
-
Karaś P., Kochanowicz K., Pitek M., Domański P., Obuchowski I., Tomiczek B., Liberek K.: Evolution towards simplicity in bacterial small heat shock protein system// eLife -, (2023), s.1-21
PublicationEvolution can tinker with multi-protein machines and replace them with simpler single-protein systems performing equivalent functions in an equally efficient manner. It is unclear how, on a molecular level, such simplification can arise. With ancestral reconstruction and biochemical analysis, we have traced the evolution of bacterial small heat shock proteins (sHsp), which help to refold proteins from aggregates using either...
-
JOURNAL OF HEAT TRANSFER-TRANSACTIONS OF THE ASME
Journals -
Polymerization-Driven Immobilization of dc-APGD Synthesized Gold Nanoparticles into a Quaternary Ammonium-Based Hydrogel Resulting in a Polymeric Nanocomposite with Heat-Transfer Applications
Publication -
The Influence of Long-Term Heat Treatment on Microstructure of Zr-Modified Aluminide Coating Deposited by CVD Method on MAR M200+Hf Nickel Superalloy
Publication -
Verification of the method of reconstructing convective velocity fields on the basis of temperature fields in vertical, differential and equally heated, open and closed channels
PublicationThis paper describes a method of reconstructing velocity fields, i.e. a numerical reconstruction procedure (NRP) that involves the numerical processing of experimentally measured temperature distributions in free convection heat transfer. The NRP consists in solving only the continuity and Navier–Stokes equations with an additional source term. This term is proportional to a known temperature (e.g. from a thermal imaging camera)...
-
Infrared techniques for natural convection investigations in channels between two vertical, parallel, isothermal and symmetrically heated plates
PublicationThe effect of the gap width between two symmetrically heated vertical, parallel, isothermal plates on intensity of natural convective heat transfer in a gas (Pr = 0.71) was experimentally studied using the balance and gradient methods. In the former method heat fluxes were determined based on measurements of the voltage and electric current supplying the heaters placed inside the walls. In the latter, heat fluxes were calculated...
-
Mechanical and Microstructural Characterization of TIG Welded Dissimilar Joints between 304L Austenitic Stainless Steel and Incoloy 800HT Nickel Alloy
PublicationIn this article, the mechanical properties and microstructure of 304L austenitic stainless steel/Incoloy 800HT nickel alloy dissimilar welded joints are investigated. The joints were made of 21.3 mm × 7.47 mm tubes using the TIG process with the use of S Ni 6082 nickel filler metal. No welding imperfections were found and high strength properties of joints were obtained, meeting the assumed acceptance criteria of the product’s...
-
Pin Angle Thermal Effects on Friction Stir Welding of AA5058 Aluminum Alloy: CFD Simulation and Experimental Validation
PublicationThe friction stir welding (FSW) of tool pin geometry plays a critical role in the final properties of the produced joint. The tool pin geometry directly affects the generation of heat and the flow of internal materials during the FSW process. The effects of the FSW tool pin angle on heat generation and internal flow have not been quantitatively investigated in detail. In this manuscript, a validated Computational Fluid Dynamic...
-
A novel concept of enhanced direct-contact condensation of vapour- inert gas mixture in a spray ejector condenser
PublicationAn analytical model of direct steam condensation (DCC) in the novel idea of spray ejector condenser (SEC) in the presence of inert gas has been developed. It is based on continuity, momentum and energy equations for the steam-carbon dioxide mixture and direct contact condensation mechanisms due to heat transfer and concentration. Crucial in the process of DCC is atomisation of the motive fluid in the ejector. The effect of atomised...
-
Archives of civil engineering. Intelligent graphic modeler integrating FE analisys of transient heat transfer with early computer-aided design of energy-efficient buildings
PublicationW pracy zaprezentowano nowatorski Modeler Rozmyty, w którym zaimplementowano unikalną koncepcję rozpoznawania. Modeler Rozmyty dokonuje ekstrakcji danych geometrycznych poprzez rozpoznanie i identyfikację niedokładnych i niejednorodnych rysunków, złożonych z prostych obiektów graficznych.
-
Aiding (opponent) flow of hybrid copper–aluminum oxide nanofluid towards an exponentially extending (lessening) sheet with thermal radiation and heat source (sink) impact
Publication -
A finite element analysis of thermal energy inclination based on ternary hybrid nanoparticles influenced by induced magnetic field
PublicationThe use of hybrid nanoparticles to improve thermal processes is a key method that has implications for a variety of interventions utilized in many sectors. This paper aimed to look into the impacts of ternary nanoparticles on hyperbolic tangent materials to establish their thermal characteristics. Flow describing equations have been explored in the presence of heat production, non-Fourier heat flux, and an induced magnetic field....
-
Impact of heat shock transcription factor 1 on global gene expression profiles in cells which induce either cytoprotective or pro-apoptotic response following hyperthermia
Publication -
The Effects of Pin Profile on HDPE Thermomechanical Phenomena during FSW
PublicationFriction stir welding (FSW) of polymeric materials has recently attracted significant attention. Herein, we present the effect of the tool pin profile on the FSW of high-density polyethylene (HDPE) joints through joint experimental analysis and thermomechanical simulations. For analysis of pin profile effects on the thermomechanical properties of HDPE joints, frustum (FPT), cubic (CPT), and triangular (TPT) pin shapes were selected...
-
Analysis of transient heat transfer operation in tube wall.Selected papers from the International Conference on Turbines of Large Output devoted to 100th Anniversary of Prof. Robert Szewalski Birthday.
PublicationW pracy przedstawiono zachowanie się wymiennika ciepła stosowanego w układzie regeneracji turbin parowych w niestacjonarnych warunkach pracy.
-
The new concept of capillary forces aided evaporator for application in domestic organic rankine cycle
PublicationThis paper presents studies on the possibility of applying capillary forces induced in the porous structure to a modern design of evaporator. The potential application of such heat exchanger is for example an evaporator of the domestic micro combined heat and power (CHP) unit. One of the problems in the micro-CHP is excessive demand for pumping power. The proposed design helps in overcoming that issue. In the evaporator outlined...
-
MALT lymphoma - Male, 71 - Tissue image [6060730023688181]
Open Research DataThis is the histopathological image of STOMACH tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
MALT lymphoma - Male, 71 - Tissue image [6060730023687921]
Open Research DataThis is the histopathological image of STOMACH tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
MALT lymphoma - Male, 71 - Tissue image [6060730023682921]
Open Research DataThis is the histopathological image of STOMACH tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
MALT lymphoma - Male, 71 - Tissue image [6060730023684751]
Open Research DataThis is the histopathological image of STOMACH tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
MALT lymphoma - Male, 71 - Tissue image [6060730023685861]
Open Research DataThis is the histopathological image of STOMACH tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
MALT lymphoma - Male, 71 - Tissue image [6060730023688701]
Open Research DataThis is the histopathological image of STOMACH tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
MALT lymphoma - Male, 71 - Tissue image [6060730023687651]
Open Research DataThis is the histopathological image of STOMACH tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
MALT lymphoma - Male, 71 - Tissue image [6060730023688521]
Open Research DataThis is the histopathological image of STOMACH tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
MALT lymphoma - Male, 71 - Tissue image [6060730023682231]
Open Research DataThis is the histopathological image of STOMACH tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
The model homologue of the partially defective human 5,10-methylenetetrahydrofolate reductase, considered as a risk factor for stroke due to increased homocysteine level, can be protected and reactivated by heat shock proteins
Publication -
On the use of the cumulative strain energy density for fatigue life assessment in advanced high-strength steels
PublicationIn this paper, the applicability of the cumulative strain energy density is explored as a fatigue indicator parameter for advanced high-strength steels subjected to strain-controlled conditions. Firstly, the cyclic stress-strain responses of nine steels, selected from three multiphase families, encompassing different elemental compositions and different heat treatment routes, were studied. Then, the predictive capabilities of the...
-
Three-dimensional numerical investigation of hybrid nanofluids in chain microchannel under electrohydrodynamic actuator
PublicationEnergy efficiency enhancement methods have received considerable attentionwithin the industry and scientific community, owing to the rising concern ofglobal energy sustainability. The present article attempts to scrutinize the effectsof electrohydrodynamics and nanofluids on the rate of heat transfer and fluidflow in the 3-D chain microchannels. Improved heat exchangers (e.g., chainmicrochannel) would have a key role in increasing...