displaying 1000 best results Help
Search results for: internal combustion engines
-
Comparative analysis of balancing of V6 engines with common- and split-pin crankshafts
PublicationAn analysis of balancing of V6 engines equipped with split-pin crankshafts with any cylinder bank angle based on the mathematical relations derived in the paper was carried out. A comparison of the quality of their balancing with engines equipped with common-pin crankshafts was also carried out. The bank angle ranges beneficial for balancing of moments of inertia forces in reciprocating motion were determined. A mathematical relation...
-
Stirling engines - the state of technology development and computational models
PublicationStirling engines represent a technologically important solution in combined heat and power systems. Their use enables the achievement of over 90 percent efficiency in the management of the primary energy source with a very high durability of the device, mainly due to the lack of contact of the working gas with external factors and a very small number of mechanical components. The use of a Stirling engine may be equally important...
-
Diagnosing marine turbine engines through energy characteristics of their flow section
PublicationThe aim of the performed research was to develop of diagnostic method of the flow section of a marine turbine combustion engine based on the level of delamination of its energy characteristics. The here adopted diagnostic model provides for a formulation of the evaluation of the technical conditions based on the measurements of the parameters of the thermodynamic medium in the characteristic control cross-sections of the engine...
-
The CFD analysis of influence the start of fuel injection (SOI) on combustion parameters and exhaust gas composition of the marine 4-stroke engine
PublicationThe paper presents a theoretical analysis of the impact of injection timing on the parameters of the combustion process and the composition of exhaust gas from a 4-stroke engine designed to shipbuilding. The analysis was carried out based on a three-dimensional multi-zone model of the combustion process. This model has been prepared on the basis of properties of the research facility. The input data to the model were obtained through...
-
Methodology for determining the elemental composition, as well as energy and ignition properties of the low-sulfur marine fuels
PublicationThe key metrological issue of substance and energy balance in research engines is the precise determination of the elemental composition of the applied fuel and its net calorific value. This makes it possible to calculate the amount of heat brought with the fuel into the combustion chamber, as well as the amount and gas composition of the exhaust. However, to fully assess the energy quality of the fuel used, its ignition properties...
-
Methods for evaluating rated power of diesel-powered generator set
PublicationBasic concepts for evaluating rated power of generator sets powered by combustion engines are presented in this article. A relation between parameters of the engine and the generator are shown. Recommendations contained in the standards and technical literature are systematized. The scheme and methodology for evaluating rated power of the generator set, based on laboratory research, are suggested. Also, the main problems which...
-
Analytical method of determining dynamic properties of thermocouples used in measurements of quick – changing temperatures of exhaust gases in marine diesel engines
PublicationThe article presents selected issues of mathematical modeling of heat exchange between the thermocouple and the exhaust gas flowing them, in unsteady conditions. On the way of energy balancing consideration of thermodynamic processes developed differential equations describing the dynamic properties for three versions of the design sheathed thermocouples: with weld isolated from the sheath, with weld welded the sheath and with...
-
Application of FMEA analysis for assessing reliability and risk in biogas-fueled engines operation process
PublicationW pracy zamieszczono propozycję wykorzystania analizy FMEA (ang. Failure mode and effects analysis) - analizy rodzajów i skutków możliwych błędów występujących w instalacjach przemysłowych z silnikami spalinowymi. Obserwowany w ostatnich latach rozwój energetyki rozproszonej, opartej na tłokowych silnikach spalinowych jest wynikiem m.in. prowadzonej polityki rozwoju wykorzystania odnawialnych źródeł energii (OŹE) związanej z zagospodarowaniem...
-
The concept of research on ecological, energy and reliability effects of modified marine fuel oils application to supply compression-ignition engines in real conditions
PublicationWithin the article, basic assumptions of the research project financed by Regional Fund for Environmental Protection and Water in Gdansk were described. The project concerns the experimental investigations carried out on laboratory compression-ignition engine in conditions of its supply with a non-standard marine fuel oil. Configuration and measuring capability of laboratory test bed presently being constructed were introduced....
-
Konstrukcje i zastosowania współczesnych silników Stirlinga
PublicationW pracy omówione zostały przyczyny rosnącego zainteresowania komercyjnego wykorzystania silników Stirlinga. Scharakteryzowane zostały podstawowe typy silników Stirlinga ze względu na układ przestrzeni roboczej i cylindrów. W pracy przedstawione zostały przykłady współczesnych konstrukcji tych silników, dokonano również analizy aktualnych i planowanych zastosowań silników Stirlinga. Omówiono podstawowe zalety i wady wykorzystania...
-
The sources of contamination and reasons of damage of the flow part of the marine turbine engine in operation
PublicationThe aim of this paperis to show particular sensitivity of the flow part of the marine turbine engine to the presence of contaminations in the intake air. The contaminations form hard-to-remove deposits in the intervene channels that result in a reduced efficiency and performance of the engine. The paper classifies the contaminants according the source of their formation and their destructive force. The performed analyses and syntheses...
-
Laboratory station for research of the innovative dry method of exhaust gas desulfurization for an engine powered with residual fuel
PublicationContemporary methods of exhaust gas desulfurization in marine engines are all expensive methods (4-5 million euro). This is, among other reasons, due to the limited market audience, but primarily due to the monop-olized position of manufacturers offering fabrication and assembly of this type of marine ship installations. Proposed as part of a research project financed by the Regional Fund for Environmental Protection and Maritime...
-
Experiments on compression ignition engine powered by nano-fuels
PublicationThe use of nanoparticles in fuels provides new opportunities for modification of fuel properties, which may affect the operational parameters of engines, in particular the efficiency and fuel consumption. The paper presents comparison of compression ignition engine performance fuelled with neat diesel and nano-diesel. Alumina (Al2O3) was used as nanoparticles. Surface-active substances, including Span 80 surfactant, as well as...
-
Application of the F-statistic of the Fisher-Snedecor distribution to analyze the significance of the effect of changes in the compression ratio of a diesel engine on the value of the specific enthalpy of the exhaust gas flow
PublicationThe paper discusses the impact of changes in the compression ratio on the operating parameters of a diesel engine, e.g. on the temperature of exhaust gases. It presents the construction of the laboratory test stand, on which experimental measurements were realized. It is characterized how the actual changes of the compression ratio were introduced to the existing engine. The program of experimental investigations taking into account...
-
Analysis of the macrostructure of the fuel spray atomized with marine engine injector
PublicationOne of the main problem influencing the combustion process in the cylinder of the marine engine is an fuel spray phenomena. The parameters describing the shape of the fuel spray are named macro parameters. This article presents the research results of the macrostructure parameters of the fuel spray atomized with the marine engine injector. The research were carried out by optical visualization measurement method of Mie scattering....
-
Evaluation of the influence of the opening pressure of a marine Diesel engine injector on the results of numerical simulation of the working cycle and their comparison with the results of the laboratory experiment
PublicationThe article presents the results of a numerical simulation of the working process carried out in a diesel engine. In the applied utility program DIESEL-RK, the laboratory engine Farymann Diesel type D10 was implemented. A selected inoperability of its functional fuel supply system - reduced opening pressure of the injector pinj - was introduced. The values of adequate diagnostic parameters were determined: working gas temperature...
-
Adoption of the F-statistic of Fisher-Snedecor distribution to analyze importance of impact of modifications of injector opening pressure of a compression ignition engine on specific enthalpy value of exhaust gas flow
PublicationThis article analyzes the effect of modifications of injector opening pressure on the operating values of a compression ignition engine, including the temperature of the fumes. A program of experimental investigation is described, considering the available test stand and measurement capabilities. The structure of the test stand on which the experimental measurements were conducted is presented. The method of introducing real modifications...
-
Research on the effect of low-sulphur marine fuels on the dynamic characteristics of a CI engine
PublicationThe implementation of low-sulphur, so-called modified marine fuels into operation requires prior labora- tory engine tests to assess the energy, emission and structural effects of their usage. This type of research are carried out on the test bed of a diesel engine as a small-scale physical model that reproduces the adequate design and process (parametric) features of a full-size marine engine. Their key stage is to determine the energy...
-
The influence of the fuel spray nozzle geometry on the exhaust gas composition from the marine 4-stroke diesel engine
PublicationThe paper presents experimental research on a 4-stroke, 3-cylinder, turbocharged AL25/30 Diesel engine. Research consisted in investigating the effect of the geometry of the fuel injectors on the exhaust gas composition from the engine. During measurements, the engine was operated with a regulator characteristic of a load range from 40 kW to 280 kW, made by electric water resistance. The engine was mechanically coupled to the electric...
-
Utilization of the zero unitarization method for the building of a ranking for diagnostic marine engine parameters
PublicationChanging some of the parameters of the engine structure affects the emission of harmful components in the exhaust gases This primarily concerns damage in the cargo exchange system as well as in the fuel system and engine boost system. Changes in emissions of harmful compounds are often ambiguous, depending largely on the parameters that shape the combustion process. An additional problem is that often simple but undesired interactions...
-
Identification of damages in the inlet air duct of a diesel engine based on exhaust gas temperature measurements
PublicationThe temperature of the exhaust gas of a diesel piston engine, measured in the characteristic control sections of its thermo-flow system, can be a valuable source of diagnostic information about the technical condition of the elements limiting the working spaces thus separated, including the turbocharging system, but also its fuel supply system and replacement of the medium. In standard marine engine measurement systems equipped...
-
Numerical analysis of the flow rig for UWS spray examination in exhaust system-relevant conditions
PublicationIn the present study, a flow rig with optical access intended for spray investigations in exhaust system-relevant conditions was analysed in terms of flow and temperature in the spray area using numerical simulations. The operation of the rig was examined for a wide range of exhaust mass flow rates, temperatures and various forms of UWS (urea-water solution) spray plumes. The locations of the injector and thermocouple were verified....
-
A conceptual design and numerical analysis of the mixerless urea-SCR system
PublicationIn the present study, an innovative design of the urea-selective catalytic reduction (SCR) system without conventional mixing elements was developed. The aim was to obtain a high degree of urea decomposition, and uniform ammonia distribution at the inlet to the catalyst, while minimising the liquid film deposition and keeping the compact design. The concept of the design was based on creating high turbulences and elongating...
-
Badania zależności między średnimi obciążeniami eksploatacyjnymi silników napędu głównego a nominalną mocą holowania statków towarowych
PublicationW referacie zaprezentowano wyniki badań eksploatacyjnych obciążeń silników napędu głównego na 17. statkach towarowych. Jako dane wejściowe wykorzystano zapisy z dzienników maszynowych, na podstawie których wyznaczono parametry eksploatacyjnego rozkładu obciążeń silników głównych w stanie eksploatacji "pływanie swobodne". Uzyskane wyniki umożliwiły wyznaczenie liniowej zależności między średnim obciążeniem silników głównych a mocą...
-
Kompleksowy model nowej generacji układu chłodzenia silnika spalinowego
PublicationPrzedstawiono tendencje w konstrukcji układów chłodzenia i dostępne komercyjne metody modelowania pracy układu chłodzenia. Przeprowadzono obliczenia symulacyjne temperatury cieczy komercyjnym programem komputerowym AmeSIM i porównano wyniki z pomiarami wykonanymi na hamowni podwoziowej. Opisano wybrane procesy wymiany ciepła występujące w układach chłodzenia. Przedstawiono ogólny model elementu cieplnego w postaci grafów wiązań...
-
Gas turbines – technological development and potential use in CAES systems
PublicationThis article briefly describes Compressed Air Energy Storage (CAES), focusing on the technological development of one of the key elements of such systems – the gas turbines. It presents the basic parameters and features of gas turbines, as well as turbine classes with example models. Main tendencies in the structural and technological development are discussed. Changes and trends on electric energy markets are becoming more and...
-
Evaluation of the energy efficiency of electric vehicle drivetrains under urban operating conditions
PublicationIn electric vehicles, as in hybrids vehicles, a very important factor affecting the energy efficiency of the powertrain is the ability to use the regenerative braking energy. Depending on the settings available in electric vehicles, the driver can choose different modes of operation: switch off the regenerative braking mode altogether, select the intensity of regenerative braking, or leave the control system in automatic mode....
-
Analysis of the structure of the atomized fuel spray with marine diesel engine injector in the early stage of injection
PublicationThis paper presents the results of the experimental research of the atomized fuel spray with the marine diesel engine injector in the constant volume chamber. The specificity of the phenomena occurring in the marine engine cylinder was the reason to use the optical visualisation method in the studies – the Mie scattering technique. This work presents an analysis of the influence of different geometry of outlet orifice and opening...
-
Możliwości redukcji przebiegowego zużycia paliwa przy zastosowaniu elektronicznych systemów wspomagających kierowców
PublicationElektroniczne systemy wspomagające kierowcę pomagają kierującym kontrolować sytuację na drodze, przekazują sygnały do układu hamulcowego i napędowego, rozpoznają znaki drogowe, pozwalają utrzymać odpowiedni dystans w czasie jazdy w kolumnie, a także kontrolują położenie pojazdu na pasie ruchu. Elek-troniczne systemy wspomagające kierowcę pomagają również zmniejszyć przebiegowe zużycie paliwa, poprzez odpowiednie sterowanie układem...
-
Zagadnienie przenikania fal cieplnych zespołu tłok-pierścienie tłokowe – tuleja cylindryczna (TPC)
PublicationNa podstawie zjawisk powodujących zużycie elementów zespołu tłok-pierścienie tłokowe-tuleja cylindryczna zostały wybrane wrażliwe na uszkodzenia cieplne elementy. Następnie została zaproponowana metoda monitorowania zmian maksymalnej amplitudy temperatury warstwy wierzchniej na podstawie której można identyfikować stan techniczny tych elementów. Polega ona na pomiarze głębokości rozchodzenia się fal termicznych za pomocą emisji...
-
Effect of the absence of clear contractual conditions for the pur-chase of combined heat and power systems through public tenders
PublicationW artykule przedstawiono dyskusję konsekwencji stosowania różnych podejść do obliczeń kontraktowych parametrów technicznych zespołów kogeneracyjnych. Obliczenia te wykonywane są na potrzeby oferty przygotowywanej w związku z ogłoszeniem przetargu publicznego na zakup siłowni kogeneracyjnej. Brak precyzyjnych zasad określających warunk, i jakie należy przyjąć do wyznaczania parametrów kontraktowych zespołów kogeneracyjnych umożliwia...
-
INVESTIGATIONS OF THE LABORATORY FARYMANN DIESEL ENGINE D10 TYPE BY MEANS OF A LANGMUIR PROBE
PublicationA precise determination of the crankshaft angular position, at which fuel ignition occurs in the SI engine, enables credible diagnosis of the technical state of its working space as well as of the fuel feed system. An observation of the Langmuir probe signal provides entirely new possibilities for engine diagnostics. The probe is introduced into the working space of a cylinder through its indicator valve. This paper presents the...
-
Dual fuelling of truck CI engine with diesel oil and mixture of propane and butane
PublicationW artykule przedstawiono zasadę działania dwupaliwowego zasilania jednocześnie olejem napędowym i odparowanym LPG silnika samochodu ciężarowego. Pokazano korzyści wynikające ze zużycia tańszego paliwa zbadane doświadczalnie.
-
Diagnosis in the power piston machines
PublicationW artykule przedstawiono obecne techniki monitorowania pracy silników i sprężarek dużej mocy. Ze względu na znaczne koszty ewentualnego wyłączenia z ruchu tego typu maszyn są one poddane obserwacji dla przewidywania ewentualnych awarii oraz planowych zatrzymań. Rośnie liczba zaawansowanych systemów pomiarowych z indykowaniem cylindrów. Dawne metody wibroakustyczne zastępowane są pomiarami parametrów procesu termodynamicznego. Słowa...
-
Development trends of automotive engine cooling systems
PublicationDzięki daleko idącym modyfikacjom układów zasilania i zapłonu silników samochodowych oraz udoskonaleniom układów oczyszczania spalin uzyskano znaczne zmniejszenie emisji związków toksycznych. Układy chłodzenia z pompą cieczy napędzaną mechanicznie stają się archaiczne nie pozwalając na swobodne sterowanie obiegiem cieczy. Również różna wartość temperatury potrzebnej do schładzania różnych procesów wymaga sterowanych zaworów trójdrożnych...
-
Problemy oszacowania trwałości i niezawodności silników o zapłonie samoczynnym z zastosowaniem teorii procesów semimarkowskich i diagnostyki
PublicationW artykule przestawiono znaczenie trwałości i niezawodności silników o zapłonie samoczynnym w eksploatacji systemów technicznych, w których są zastosowane. Wykazano, że do oszacowania trwałości i niezawodności wspomnianych silników bardziej przydatne są modele opracowane w formie semimarkowskiego procesu zmian stanów technicznych tego rodzaju silników w porównaniu do modeli proponowanych w klasycznej teorii niezawodności. Scharakteryzowano...
-
A PROPOSAL OF A DESCRIPTION OF THE OPERATING CONDITIONS OF DIESEL-ELECTRIC LOCOMOTIVES
PublicationThe paper presents a proposal of a description of the operating conditions of diesel-electric locomotives. The proposal is a result of the operational experience and the analysis of the locomotive operation. It constitutes a significant simplification in relation to the descriptions currently used by domestic carriers. The paper also presents examples of analyses of the operating conditions of locomotives using the proposed method.
-
Model of the hydraulic pump powertrain of refuse collection vehicle compaction mechanism
PublicationW pracy przedstawiono symulację pracy układu napędowego pompy hydraulicznej mechanizmu prasującego śmieciarki oraz wpływ różnych konfiguracji elementów składowych tego urządzenia na zużycie paliwa silnika napędowego w warunkach przyjętego cyklu obciążenia. W tym celu wykorzystano model układu napędowego pompy hydraulicznej mechanizmu prasującego śmieciarki w formie grafów wiązań oraz wyniki pomiarów ciśnienia roboczego w siłownikach...
-
Analysis of accumulation possibility of energy dissipated in the braking process of train driven by hybrid locomotive
PublicationW tradycyjnym procesie hamowania cała energia kinetyczna lub potencjalna pociągu napędzanego lokomotywą z silnikiem spalinowym jest rozpraszana do otoczenia w postaci energii cieplnej. W lokomotywach hybrydowych istnieje możliwość odzyskania części tej energii przez przekazanie jej do akumulatorów i ponowne wykorzystanie do napędu pociągu. W pracy przedstawiono model układu napędowego lokomotywy hybrydowej z silnikiem spalinowym,...
-
Problemy sterowania wydajnością pompy cieczy chłodzącej silnik samochodowy z zapłonem iskrowym
PublicationW pracy przedstawiono przegląd wybranych pozycji literatury na temat możliwości sterowania chłodzeniem silnika. Parametrem wybranym przez autora do oceny stanu cieplnego silnika jest temperatura ścianki komory spalania. Opisano pomiary tej temperatury jako funkcji wydajności głównej pompy cieczy chłodzącej podczas rozgrzewania silnika.
-
Analysis of the torque response of a car engine to the step change of the control signal
PublicationW pracy zamieszczono wyniki badań silnika samochodu osobowego w warunkach nieustalonych. Stan obciążenia silnika wynikał z realizowanego cyklu jezdnego w warunkach drogowych oraz sposobu sterowania układem napędowym. Parametry trakcyjne pojazdu mierzone były za pomocą systemu GPS z fenomenologiczną korektą sygnału wysokości, na której się on znajdował. Wybrane parametry pracy silnika mierzone były za pomocą sytemu komunikującego...
-
Measurement of engine and vehicle parameters using onboard CAN network
PublicationWspółczesne samochody wyposażane są w dużą liczbę układów elektronicznych, które wymagają wzajemnej wymiany informacji. Techniczne problemy niezależnego łączenia ze sobą dużej liczby sterowników doprowadziły do powstania pokładowych sieci wymiany danych. Do najpopularniejszych z nich zalicza się obecnie system CAN. W pracy przedstawiono metodę rozpoznawania ramek wiadomości transmitowanych w pokładowej sieci CAN pojazdu przez sterowniki....
-
Możliwości zamiany strumieni ciepła odpadowego silników pojazdów na moc efektywną
PublicationW pracy przedstawiono przegląd wybranych pozycji literatury na temat możliwości wykorzystania ciepła odprowadzanego od silnika do otoczenia. Wymieniono głównie nowe nie stosowane seryjnie ale obecnie projektowane i badane układy. Wskazano na niekorzystne cechy takie jak duża masa i koszty układów parowych. Termogeneratory z kolei charakteryzują się małą mocą elektryczną na jednostkę masy. W ostatnim rozdziale wspomniano o akumulacji...
-
Dichotomous design of real-time systems
PublicationW pracy prezentuje się i analizuje dwie podstawowe metody projektowania komputerowych systemów czasu rzeczywistego, spełniających rozmaite zadania z zakresu automatyki, sterowania, nadzoru i diagnostyki, w których następuje interakcja komputera z obiektami i procesami przemysłowymi, które posiadają naturę ciągłą (pozwalającą na ścisłą matematyczną charakteryzację w czasie ciągłym). Definiuje się podejście uwarunkowane kontekstowo...
-
Possibility of defining theoretical operation for diesel mengines in energy terms
PublicationPrzedstawiono propozycję wartościowania (ilościowego określenia) działania dowolnego silnika o zapłonie samoczynnym, na przykładzie okrętowego silnika głównego, w którym zachodzą oddziaływania energetyczne w określonym czasie. Działanie to rozumiane jest jako przekazywanie energii śrubie napędowej w ustalonym czasie, w którym zachodzi przetwarzanie i przenoszenie energii w formie pracy bądź ciepła. Wartościowanie działania silników...
-
The time of the first transition of the semi-Markov process in the evaluation of diesel engine operation
PublicationW referacie przedstawiono rozwinięcie prezentowanej w literaturze metody ilościowej oceny działania na przykładzie okrętowego silnika głównego z zapłonem samoczynnym. Według tej interpretacji, działanie silnika może zostać przedstawione jako wielkość fizyczna. W tym aspekcie, na przykładzie okrętowego silnika napędu głównego dokonano oceny przydatności tej wielkości do opisu własności niezawodnościowych silnika. Precyzyjne określenie...
-
Diagnostic tolerances' evaluation method of the start-up exhaust temperature of a naval gas turbine
PublicationThe conducted investigations aimed to elaborate the method of marking diagnostic tolerances of the exhaust temperature of a gas turbine observed during engine's start-up process. The diagnostic tolerances were determined by means of statistical inference by creating the hypothesis about a normal distribution of the start-up exhaust temperature's dispersion in the initial operation moment, which was subsequently verified applying...
-
Reduction of the reaction torque of an in-line four-cylinder four-stroke engine
PublicationW pracy przedstawiono zarówno dokładne jak i uproszczone zależności na przebieg momentu reakcyjnego silnika, jedno i wielocylindrowego, przenoszonego na ramę pojazdu lub fundament. Wyprowadzono zależność na wartość przesunięcia wałków wyrównoważających zapewniającą całkowite wyeliminowanie wpływu sił bezwładności na przebieg momentu reakcyjnego w silnikach czterosuwowych czterocylindrowych. Wprowadzono kryteria doboru optymalnej...
-
Analysis of the possibility of determining the general characteristics using the operational data of a vehicle engine
PublicationThe paper presents an analysis of the possibility of determining the general characteristics using the operational data of an engine of refuse collection vehicle. Data acquisition was done by reading information from the CAN network using FMS standard (Fleet Management System), which is widely used in heavy duty vehicles since year 2002. The paper presents the analysis of the expected measurement uncertainties resulting from the...
-
The influence of settable parameters of switching gasoline/LPG on exhaust toxic emissions
PublicationThe main objective of the studies shown in the paper was to develop a proper strategy for settable parameters of ECU to decrease total emission of toxic components in composition of exhaust during a cold start phase. The experimental research has been performed for engine running at idle and for engine running on the chassis dynamometer (performing European Driving Test NEDC).