Filters
total: 557
Search results for: MOLECULAR HYDROGEN
-
Maximizing Bio-Hydrogen and Energy Yields Obtained in a Self-Fermented Anaerobic Bioreactor by Screening of Different Sewage Sludge Pretreatment Methods
PublicationEgypt faces significant challenges in managing its sewage sludge generated in large quantities from wastewater treatment plants. This study investigates the feasibility of utilizing sewage sludge as a renewable resource for hydrogen production through anaerobic digestion at the 100 L bioreactor level. Hydrogen is considered a promising alternative energy source due to its high energy content and environmental benefits. To optimize...
-
Application of atmospheric pressure microwave plasma source for hydrogen production from ethanol
PublicationIn contrast to conventional technologies of hydrogen production like water electrolysis or coal gasification we propose a method based on the atmospheric pressure microwave plasma. In this paper we present results of the experimental investigations of the hydrogen production from ethanol in the atmospheric pressure plasma generated in waveguidesupplied cylindrical type nozzleless microwave (915 MHz and 2.45 GHz) plasma source (MPS)....
-
Direct reduction of pellets through hydrogen: Experimental and model behaviour
PublicationThis paper presents the hydrogen reduction behaviour of industrial pellets designed for the efficient hydrogen based direct reduction. The pellets were provided with very low non ferrous oxides percentage (0.52 of basicity index) and with the absence on TiO2 oxides. The pellets measured diameters in the range 1.14–1.72 cm and were characterized in terms of porosity, pores size, tortuosity and compression strength. The pellets were...
-
Towards Computer-Aided Graphene Covered TiO2-Cu/(CuxOy) Composite Design for the Purpose of Photoinduced Hydrogen Evolution
PublicationIn search a hydrogen source, we synthesized TiO2-Cu-graphene composite photocatalyst for hydrogen evolution. The catalyst is a new and unique material as it consists of copper-decorated TiO2 particles covered tightly in graphene and obtained in a fluidized bed reactor. Both, reduction of copper from Cu(CH3COO) at the surface of TiO2 particles and covering of TiO2-Cu in graphene thin layer by Chemical Vapour Deposition (CVD) were...
-
New Carvone-Based Deep Eutectic Solvents for Siloxanes Capture from Biogas
PublicationDuring biogas combustion, siloxanes form deposits of SiO2 on engine components, thus shortening the lifespan of the installation. Therefore, the development of new methods for the purification of biogas is receiving increasing attention. One of the most effective methods is physical absorption with the use of appropriate solvents. According to the principles of green engineering, solvents should be biodegradable, non-toxic, and...
-
Preliminary investigations of effect of conditions of FCAW process on diffusible hydrogen content in deposited metal
PublicationOne of the types of hydrogen degradation of steel welded joints is cold cracking. The direct cause of the formation of cold cracks is simultaneous presence of hydrogen, residual stresses and brittle structure. The way of preventing the occurring of degradation is to eliminate at least one of these factors. Practice has shown that the best solution is to control the amount of hydrogen in deposited metal. In this paper the state...
-
Influence of High Temperature Oxidation on Hydrogen Absorption and Degradation of Zircaloy-2 and Zr 700 Alloys
PublicationThe present research was aimed at determining the effects of the oxide layers on hydrogen absorption, microstructure and mechanical properties of the Zircaloy- 2 and Zr 702 alloys. The oxidation was made at 350 °C, 700 °C and 900 °C for 10 to 30 min in laboratory air, followed by hydrogen cathodic charging for 72 h and annealing at 400 °C for 4 h. The slow strain rate tests were carried out on oxidized, charged and annealed specimens. The...
-
Application of a catalytic combustion sensor (Pellistor) for the monitoring of the explosiveness of a hydrogen-air mixture in the upper explosive limit range
PublicationA new technique is presented for continuous measurements of hydrogen contamination by air in the upper explosive limit range. It is based on the application of a catalytic combustion sensor placed in a cell through which the tested sample passes. The air content is the function of the quantity of formed heat during catalytic combustion of hydrogen inside the sensor. There is the possibility of using the method in industrial installations...
-
Hydrogen Production via Biomethane Reforming in DBD Reactor
PublicationProduction of hydrogen from CH4:CO2 (70%:30%) mixture simulating dry biogas in a DBD reactor supplied with AC of 1.0-2.0 kHz or nanosecond negative pulses is presented. We have found that hydrogen production and methane conversion degree increase linearly with discharge power in the range of up to 50 W. Nanosecond voltage pulses are much more efficient in hydrogen production than sine AC voltage
-
Effect of underwater wet welding conditions on the diffusible hydrogen content in deposited metal
PublicationIn the study mercury displacement method was used for determination of diffusible hydrogen amount in deposited metal obtained during underwater wet welding with covered electrodes in laboratory conditions according to a two-level full factorial design for three factors. The factors and their levels were chosen among conditions and parameters of welding in accordance with the results of own preliminary studies. A statistical analysis...
-
Corrosion behavior of hydrogen charged super duplex stainless steel welded joints
PublicationThe electrochemical behavior of the weld metal, heat-affected zone (HAZ), and base material of super duplex stainless steel (SDSS) welded joints, made with the application of flux-cored arc welding (FCAW) and submerged arc welding (SAW), were investigated with the use of metallographic examinations (optical microscopy and scanning electron microscopy), potentiodynamic polarization measurements and total hydrogen content determination...
-
The effect of pre-hydrogen charging on corrosion behaviour of superduplex stainless steel welded joints
PublicationThe paper presents results of research undertaken to determine the influence of hydrogen on passivity and corrosion resistance of 2507 super duplex stainless steel welded joints. Butt welded joints were made with low heat input using flux corded arc welding (FCAW) method. Coupons of 5.0 x 5.0 mm were cut from the welded joints containing weld metal (WM), heat affected zone (HAZ) and parent metal (PM). Hydrogen was introduced...
-
Hydrogen production from wood waste by mean of dark fermentation
PublicationThe utilization of wood wastes in clean and green chemistry method like by mean of dark fermentation, is a highly desired solution of waste management. In the article model for the estimation hydrogen potential of wood waste is given. The model has been used to calculate the potential theoretical hydrogen mass that can be produced from wood wastes in Pomerania and Silesia: pine, spruce, fir, beech and oak. In the introduction,...
-
Hydrogen production from ethanol In nitrogen microwave plasma At atmospheric pressure
PublicationHydrogen seems to be one of the most promising alternative energy sources. It is a renewable fuel as it could be produced from e.g. waste or bio-ethanol. Furthermore hydrogen is compatible with fuel cells and is environmentally clean. In contrast to conventional methods of hydrogen production such as water electrolysis or coal gasification we propose a method based on atmospheric pressure microwave plasma. In this paper we present...
-
Performance and emission characteristics of diesel engines running on gaseous fuels in dual-fuel mode
PublicationConventional fossil fuels are being substituted with alternative green fuels because of their greenhouse gas emissions and pollution problems, which pose a severe threat to the environment. Several studies have reported the usage of biodiesel and gaseous fuels in both single and dual-fuel modes. Gaseous fuels such as producer gas, biogas, syngas, and hydrogen produced from renewable biomass could potentially be used along with...
-
A novel concept of H2/O2 steam generator
PublicationThis paper presents an idea of hydrogen utilization to steam generation to drive a turbine and produce electricity or to supply a condenser as an element of a heating system. Electrolysis process is considered as a source of hydrogen as well as oxygen. Hydrogen combustion with a stoichiometric ratio of pure oxygen produces steam at very high temperature. Steam temperature can be controlled by mixing the generated steam with liquid...
-
A NOVEL CONCEPT OF H2/O2 STEAM GENERATOR
PublicationThis paper presents an idea of hydrogen utilization to steam generation to drive a turbine and produce electricity or to supply a condenser as an element of heating system. Electrolysis process is considered as a source of hydrogen as well as oxygen. Hydrogen combustion with a stoichiometric ratio of pure oxygen produces steam at very high temperature. Steam temperature can be controlled by mixing the generated steam with liquid...
-
Comparison of hydrogen bonds and diverse weak interactions of the nitro group in 2-methyl-4-nitroanilinium nitrate, bisulfate and two hexafluoridosilicates: elementary graph-set approach
PublicationCrystal structures of (H2m4na)NO3 (1), (H2m4na)HSO4 (2), (H2m4na)2SiF6 (3) and (H2m4na)2SiF6*2H2O (4), where 2m4na = 2-methyl-4-nitroaniline, are presented. Two layers of interactions occur in the structures, N—H...O/F hydrogen bonds and interactions with the nitro group. Although diverse, hydrogen-bonding patterns are compared with each other by means of interrelations among elementary graph-set descriptors and descriptors of hydrogen-bonding...
-
Bioconversion of waste materials to hydrogen via dark fermentation using Enterobacter aerogenes
PublicationHydrogen can be obtained via dark fermentation with the use of anaerobic Enterobacter aerogenes. The efficiency of hydrogen production by fermentation techniques is strongly dependent on the con-ditions used i.e. the pH range, temperature, composition of fermentation broths, oxygen content, or even the presence of substances with potentially inhibitory effects on the microbiological culture [1-4]. The paper describes the study...
-
Performance of the PEM fuel cell module. Part 2. Effect of excess ratio and stack temperature
PublicationThe paper describes a fuel cell based system performance under different thermal conditions. The system could be fed with bottled hydrogen or with very high purity hydrogen obtained from reforming of methanol. The system is based on two fuel cell units (1.2 kW each, produced by Ballard Power Systems Inc. and called Nexa), DC/DC converter, DC/AC inverter, microprocessor control unit, load unit, bottled hydrogen supply system and...
-
Diffusible hydrogen content in deposited metal of multilayer welded joints
PublicationThe article describes manufacturing technology of multilayer joints in terms of control the diffusible hydrogen content. Diffusible hydrogen content in deposited metal for multilayer welded joints made of covered rutile electrodes or covered cellulosic and basic electrodes was determined. It was found that after four beads, the diffusible hydrogen content decreases in the case of the first technology from 36 ml/100 g to 18 ml/100...
-
Oxidation and hydrogen behavior in Zr-2Mn alloy
PublicationThe purpose of the present research was to determine the oxidation and hydrogenation behavior in the new Zr-2Mn alloy. The oxidation of alloy was performed at temperatures between 350°C and 900°C for 30 minutes. The hydrogen charging was made for 72 h at a current density 80 mA/cm2. The charged samples were heat treated at 400°C for 4 h to obtain a uniform hydrogen profile content across the sample. The oxidation resulted in an...
-
Supramolecular Synthesis Based on a Combination of Se···N Secondary Bonding Interactions with Hydrogen and Halogen Bonds
PublicationExamination of the solid state structures of 2,1,3-benzoselenadiazole complexes with hydrogen or halogen bond donors has demonstrated that the 2,1,3-benzoselenadiazole molecules preferably form centrosymmetric dimers with use of [Se–N]2 supramolecular synthon, whereas the two remaining nitrogen atoms not involved in the [Se–N]2 supramolecular interactions can act as acceptors of hydrogen or halogen bonds. Cocrystallization of selenadiazoles...
-
The Effect of Welding Conditions on Diffusible Hydrogen Content in Deposited Metal
PublicationThe article presents the results of a literature survey and preliminary tests which set out effects of welding conditions on the amount of diffusible hydrogen in deposited metal. Experiments were conducted by using rutile coated electrodes which generate high contents of diffusible hydrogen in deposited metal. The amount of diffusible hydrogen was determined by a glycerin test.Eleven factors were considered: the electrode angle,...
-
Hydrogen degradation of pre-oxidized zirconium alloys
PublicationThe presence of the oxide layers on Zr alloys may retard or enhance the hydrogen entry and material degradation, depending on the layer features. This research has been aimed to determine the effects of pre-oxidation of the Zircaloy-2 alloy at a different temperature on hydrogen degradation. The specimens were oxidised in laboratory air at 350°C, 700°C, and 900°C. After, some samples were tensed at 10-5 strain rate and simultaneously...
-
Effect of Microplastics Pollution on Hydrogen Production from Biomass: A Comprehensive Review
PublicationHydrogen production from biomass and organic wastes is considered as a potential alternative energy source and is known as a clean and CO2-free fuel energy carrier. H2 is considered very promising among the other energy sources; therefore, the effective conversion of biomass and organic solid waste to this secondary energy source is urgently sought. As a result, it is of importance to assess the impact of the existence of microplastics...
-
Review of hydrogen production technologies for automotive sector – thermodynamic analysis of energy and exergy losses
PublicationFew recent years has shown that hydrogen technology has a good chance to replace petroleum technology in automotive sector. However, hydrogen in pure form practically does not occur on Earth. That is why H2 form is used only as an energy carrier and it must be produced using another source of energy form water or hydrocarbon fuels. In this paper short overview of hydrogen production technology has been presented, with energy and...
-
Assessment of hydrogenation of deposited metal of P 62 MR covered electrodes
PublicationThe determination of diffusible hydrogen content in deposited metal of P 62 MR covered electrodes for manual metal arc welding by mercury method was carried out. The test results indicate that covered electrodes 62 P MR grade generate a mean of 4.02 ml/100g of diffusible hydrogen in deposited metal, which is consistent with H5 class.
-
<i>N,N</i>'-diphenylthiourea acetone monosolvate
PublicationIn the title compound, C13H12N2S·C3H6O, the phenyl rings of the thiourea molecule are in syn and anti positions in relation to the C=S bond. Two molecules are connected by N-HS=C hydrogen bonds into a centrosymmetric dimer. An additional N-HO=C hydrogen bond to the acetone solvent molecule and some weak C-H interactions reinforce the crystal structure.
-
Fermentative Conversion of Two-Step Pre-Treated Lignocellulosic Biomass to Hydrogen
PublicationFermentative hydrogen production via dark fermentation with the application of lignocellulosic biomass requires a multistep pre-treatment procedure, due to the complexed structure of the raw material. Hence, the comparison of the hydrogen productivity potential of different lignocellulosic materials (LCMs) in relation to the lignocellulosic biomass composition is often considered as an interesting field of research. In this study,...
-
Optimisation of cooperation of hybrid renewable energy sources with hydrogen energy storage toward the lowest net present cost
PublicationThe paper presents the results of a technical and economic analysis of the power supply for a model industrial facility based on intermittent renewable energy sources in the form of wind turbines and photovoltaic modules, supplemented with hydrogen energy storage. The adopted power supply strategy assumed the maximisation of self-consumption of self-produced electricity. Six variants were considered, including two with an energy...
-
The effect of imidazolium ionic liquid on the morphology of Pt nanoparticles deposited on the surface of SrTiO3 and photoactivity of Pt–SrTiO3 composite in the H2 generation reaction
PublicationPhotocatalytic water splitting has great potential in solar-hydrogen production as a low-cost and environmentally friendly method. Different unique techniques used to obtain photocatalysts with various modifications to improve H2 generation have been introduced. In the present work, SrTiO3 was successfully synthesized via the solvothermal method in the presence of ionic liquid (IL) - 1-butyl-3-methylimidazolium bromide ([BMIM][Br])...
-
Crystallographic study of self-organization in the solid state including quasi-aromatic pseudo-ring stacking interactions in 1-benzoyl-3-(3,4-dimethoxyphenyl)thiourea and 1-benzoyl-3-(2-hydroxypropyl)thiourea
Publication1-Benzoylthioureas contain both carbonyl and thiocarbonyl functional groups and are of interest for their biological activity, metal coordination ability and involvement in hydrogen-bond formation. Two novel 1-benzoylthiourea derivatives, namely 1-benzoyl-3-(3,4-dimethoxyphenyl)thiourea, C₁₆H₁₆N₂O₃S, (I), and 1-benzoyl-3-(2-hydroxypropyl)thiourea, C₁₁H₁₄N₂O₂S, (II), have been synthesized and characterized. Compound (I) crystallizes...
-
Influence of hydrogen on a nanocrystalline high-entropy oxide with application potential in hydrogen technologies
PublicationThe influence of hydrogen on a (Co0⋅2Cu0⋅2Mg0⋅2Ni0⋅2Zn0.2)O HEO with a rock salt structure was studied. Two forms of this HEO (nanopowder and sinter) were prepared via mechanochemical synthesis (MS) and additional heat treatment, respectively. The chemical stability of the synthesized samples in a pure hydrogen atmosphere was investigated using Sievert’s technique. High-pressure hydrogenation at 250 ◦C had no noticeable effect...
-
Determination of moisture resistance of covered electrodes according to PN-EN ISO 14372
PublicationMoisture present in the electrode covering is one of the sources of diffusible hydrogen in welded joints. In order to study the diffusible hydrogen content in deposited metal, a stand for moisturizing covered electrodes, in accordance with the PN-EN ISO 14372 standard, was built. After the stand was completed, a test of moisturizing the electrodes was carried out and measurements of the diffusible hydrogen content in deposited...
-
Comparative study of a combined heat and power plant retrofitted by CO2 capture during the combustion of syngas from sewage sludge gasification versus zero-emission combustion of hydrogen produced using renewables
PublicationWith ecological requirements aimed at limiting the production of CO2, it is necessary to produce all, or most of the energy from RES. During the transformation process, ecological and highly efficient combustion power plants will be needed. The classic cycle of combined heat and power (CCGT) with green improvements will continue to be one of the most suitable technologies for this task. This article presents the modernization of...
-
Dual functionality of amphiphilic 1-alkyl-3-methylimidazolium hydrogen sulfate ionic liquids: surfactants with catalytic function
PublicationA series of amphiphilic 1-alkyl-3-methylimidazolium hydrogen sulfate ionic liquids were synthesized. Acidic hydrogen sulfate ionic liquids with the alkyl chains C6–C14 are characterized by good surface properties. Their surface properties (adsorption and micellization parameters, degree of ionization of micelles, Krafft temperatures and thermodynamic parameters) were determined. Synthesized ionic liquids were applied as a co-catalyst...
-
Correlation between structural and electrical properties in highly porous (Y,Sr)(Ti,Nb)O3-delta SOFC anodes
PublicationIn order to find a relationship between structural and electrical properties, niobium and yttrium doped SrTiO3 ceramics were prepared via solid-state reaction. The samples were sintered in hydrogen and air conditions. The samples were also fabricated with a pore-former to obtain highly porous specimens. The electrical properties of Nb-doped SrTiO3 samples and yttrium and niobium co-doped SrTiO3 were compared. The comparable electrical...
-
Techno-economic assessment of cooperation of hybrid renewable energy sources with hydrogen storage
PublicationThe paper presents a technical and economic analysis of the power supply for a model industrial facility with the use of the most promising renewable energy sources (RES), supported by a hydrogen energy storage. This scenario was compared with the variants of supplying the facility directly from the grid and from RES without energy storage. A strategy was proposed for powering the plant aimed at maximising self-consumption of self-generated...
-
Photocatalysts for Solar Energy Conversion
PublicationPhotocatalytic oxidation over suspended solid photocatalysts (e.g., titanium dioxide) has been proposed as a sustainable process for treatment and purification of water and wastewater as well as the process for photoconversion of solar energy to hydrogen, methane, and other low hydrocarbons. Solar radiation could be used to drive heterogeneous electrochemical reactions at the surface of an optically active photocatalyst (e.g.,...
-
Sulfate‐reducing bacteria‐assisted hydrogen‐induced stress cracking of 2205 duplex stainless steels
PublicationThe paper presents the results of a laboratory investigation of the microbiologically assisted hydrogen‐induced stress cracking (HISC) of 2,205 duplex stainless steel (DSS). The testing of susceptibility toward HISC was performed with two different methods. Precharged in sulfate‐reducing bacteria (SRB), inoculated medium samples were subjected to slow strain‐rate testing in artificial seawater. In situ constant load tests were...
-
Urchin-like TiO2 structures decorated with lanthanide-doped Bi2S3 quantum dots to boost hydrogen photogeneration performance
PublicationThe formation of heterojunctions between wide- and narrow-bandgap photocatalysts is commonly employed to boost the efficiency of photocatalytic hydrogen generation. Herein, the photoactivity of urchin-like rutile particles is increased by decorating with pristine as well as Er- or Yb-doped Bi2S3 quantum dots (QDs) at varied QD loadings (1–20 wt%) and doping degrees (1–15 mol%), and the best hydrogen evolution performance is achieved at...
-
Experimental study and numerical simulation on porosity dependent direct reducibility of high-grade iron oxide pellets in hydrogen
PublicationThe transition to more environmentally friendly steel production methods has intensified research into hydrogen-based direct reduction (HyDR) of iron oxide pellets. The aim of this study is to systematically investigate the kinetics of the reduction process, the evolution of porosity and the resulting microstructural changes on the reduction behavior of high-quality pellets during HyDR of iron ore at different temperatures. A modified...
-
Shape-controllable synthesis of GdVO4 photocatalysts and their tunable properties in photocatalytic hydrogen generation
PublicationNovel visible light responsive materials for water splitting are essential for the efficient conversion of solar energy into hydrogen bond energy. Among other semiconductors, gadolinium orthovanadate has appropriate conduction and valence band edges positioned to split water molecules and a narrow band gap that allows the use of visible light for hydrogen generation. Thus, we present here that hydrogen evolution under visible light...
-
Alternative methods for dark fermentation course analysis
PublicationDark fermentation course analysis is crucial, as complexed matrix of gaseous components may be formed and revealed during the process. The paper considers key issues related to the microbiological process in which complex organic substances are transformed into hydrogen. For the purposes of hydrogen generation, the application of wastewater mixed sludge pre-treated according to Faloye method (Faloye et al. in Int J Hydrog Energy...
-
Intermolecular Interactions of Edaravone in Aqueous Solutions of Ethaline and Glyceline Inferred from Experiments and Quantum Chemistry Computations
PublicationEdaravone, acting as a cerebral protective agent, is administered to treat acute brain infarction. Its poor solubility is addressed here by means of optimizing the composition of the aqueous choline chloride (ChCl)-based eutectic solvents prepared with ethylene glycol (EG) or glycerol (GL) in the three different designed solvents compositions. The slurry method was used for spectroscopic solubility determination in temperatures...
-
Effect of shielded electrode wet welding conditions on diffusible hydrogen content in deposited metal
PublicationWet welding is the most popular method of joining in water enviroment. During underwater welding, the weldability of steel is limited by the higher cooling rates and hydrogen content in weld metal. Article presents results of preliminary tests on the effects of wet welding conditions on diffusible hydrogen amount. Seven parameters were optimized using a Plackett-Burman plan to get the most relevant variables. These parameters were:...
-
Preparation and X-ray structures of selected aminium thiosulfates
PublicationVarious types of aminium thiosulfates (1–6), including hydrates and mixed salts, have been obtained by the reaction of ammonium thiosulfate with amines. Tertbutylamine, cyclo-hexylamine and 1,6-diaminohexane gave crystals of (t-BuNH3)2S2O3·H2O (1), (c-C6H11NH3)2S2O3 (3) and {(NH4)2(H3NC6H12NH3)(S2O3)2} (6), respectively, which were investigated by X-ray structural analysis. Extensive hydrogen bonding of the N-H…O and N-H…S type...
-
THEORETICAL POTENTIAL OF HYDROGEN PRODUCTION FROM TEXTILES WASTES IN POMERANIAN REGION BY MEANS OF DARK FERMENTATION
PublicationModel has been developed for calculating theoretical mass of hydrogen produced from textile wastes by mean of dark fermentation. As vegetable fibres wastes were chosen two mostly used — cotton and linen (flax). As the synthethic carbohydrate rich fiber was chosen viscose. In the background there were introduced: problems of dark fermentation, characteristics of textile material structure. Additionally pathways of the process...
-
Investigating BiMeVOx compounds as potential photoelectrochemical and electrochemical materials for renewable hydrogen production
PublicationIn this study, BiMeVOx compounds (where Me: Co, Mo, Ce, Zr) were synthesized and characterized as potential photoelectrochemical materials for solar water splitting, the hydrogen evolution reaction (HER), and oxygen evolution reaction (OER). The analysis confirmed the successful formation of phase BiMeVOx compounds with the desired crystal structure. Among the tested materials, BiCoVOx(800) showed the highest photocurrent density...