displaying 1000 best results Help
Search results for: HEAT TRANSFER TEMPERATURE FIELD THERMAL BRIDGE GREEN'S FUNCTION
-
Processing, physico-mechanical and thermal properties of reclaimed GTR and NBR/reclaimed GTR blends as function of various additives
PublicationIn this work, ground tire rubber (GTR) was mechano-chemically reclaimed in the presence of bitumen and various additives. During studies three types of processing and curing additives: (i) peptizer P300; (ii) vulcanization accelerator tetramethylthiuram disulfide (TMTD) and (iii) organic peroxide di(2-tert-butyl-peroxyisopropyl)benzene (BIB1) were applied to enhance reclaiming of GTR. Reclaiming process was evaluated by oscillating...
-
Thermal and solutal performance of Cu/CuO nanoparticles on a non-linear radially stretching surface with heat source/sink and varying chemical reaction effects
Publication -
Factors affecting low-temperature cracking of asphalt pavements: analysis of field observations using the ordered logistic model
PublicationAccurate identification of factors that primarily affect the number of low-temperature cracks is crucial for selection of road materials and planning of pavement maintenance. Field investigations of lowtemperature cracks were performed in the years 2014 and 2020 on the same 68 road sections being in service in typical traffic conditions. The collected data were statistically analysed using the ordered logistic regression model....
-
Analytical solution of non-stationary heat conduction problem for two sliding layers with time-dependent friction conditions
PublicationIn this article we conduct an overview of various types of thermal contact conditions at the sliding interface. We formulate a problem of non-stationary heat conduction in two sliding layers with generalized thermal contact conditions allowing for dependence of the heat-generation coefficient and contact heat transfer coefficient on time. We then derive an analytical solution of the problem by constructing a special coordinate...
-
A comparative study of different methods for heat transfer enhanced by the use of TVG
PublicationArtykuł dotyczy badań eksperymentalnych i numerycznych intensyfikacji wymiany ciepła w modelowym wymienniku ciepła z turbulizatorami przepływu dla różnej geometrii turbulizatorów. Do badań eksperymentalnych wykorzystano termografię ciekłokrystaliczną a modelowanie fizyczne wykonano za pomocą kodu komputerowego FLUENT.
-
Hybrid evolutionary partitioning algorithm for heat transfer enhancement in VLSI circuits
PublicationW niniejszym artykule przedstawiono metodę pozwalającą na polepszenie transferu ciepła z układu scalonego do otoczenia poprzez zwiększenie liczby połączeń zewnętrznych, co pozwoliło na polepszenie przewodności cieplnej układu scalonego. Dla osiągnięcia tego celu opracowano nowy, hybrydowy, ewolucyjny algorytm podziału (ang. Hybrid Evolutionary Partitioning Algorithm - HEPA). Obliczenia przeprowadzone dla wybranych przykładów testowych...
-
Turbulent flow and heat transfer of a liquid film formed by impinging jet.
PublicationZaproponowano prosty model wymiany ciepła w turbulentnym filmie cieczowym utworzonym przez uderzająca strugę. Rozpatrzono dwa przypadki: przepływ rozwijający się i w pełni rozwinięty filmu cieczowego. W obu przypadkach model wyprowadzono na podstawie zmiany grubości filmu w wyniku działania sił bezwładności i sił tarcia. Wyznaczono profile prędkości w obu zakresach co umożliwia wyznaczenie współczynników wymiany ciepła.
-
Experimental study of natural convection heat transfer from horizontal conic
PublicationPrzedstawiono badania eksperymentalne i ich wyniki konwekcji swobodnej w wodzie i powietrzu poziomych stożków o kącie przy podstawie 30, 45 i 60 deg. Wyniki badań wykazują dobrą zgodność z rozwiązaniem teoretycznym i z danymi literaturowymi.
-
Numerical single-phase modeling of turbulent flow and heat transfer of nanofluids
PublicationIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (6 000< Re < 12 000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with published experimental data.
-
Heat transfer and fluid flow visualization using liquid crystal thermography
PublicationW pracy przedstawiono możliwości wykrzystania termografii ciekłokrystalicznej do badań wymiany ciepła oraz wizualizacji pola przepływu w elementach urządzeń przemysłowych.
-
The Numerical Comparison of Heat Transfer in a Coated and Fixed Bed of an Adsorption Chiller
Publication -
Experimental study of heat transfer intensification in surface cooling using microjets
PublicationW pracy przedstawiono badania eksperymentalne intensyfikacji wymiany ciepła podczas chłodzenia powierzchni mikrostrugami. Wyniki badań porównano z własnym modelem teoretycznym zjawiska.
-
Effects of a rotating magnetic field on gas-liquid mass transfer coefficient
Publication -
Michał Ryms dr inż.
PeopleMichał Ryms, PhD, Eng. is the physicist, graduate of the Gdańsk University of Technology. PhD thesis defended at the Chemical Faculty. Since 2011 an employee at the Department of Chemical Apparatus and Theory of Machines, Chemical Faculty, Gdansk University of Technology, POLAND – now as an assistant professor. His research interests includes: improvement of energy efficiency and possibilities of new application of phase change...
-
Linear impedance as a function of A.C. voltage for 50(2Bi2O3-V2O5)-50SrB4O7 glass heat treated at 693 K measured with impedance spectroscopy method at 273 K
Open Research DataThe linear electrcial properties as a function of A.C. voltage for 50(2Bi2O3-V2O5)-50SrB4O7 glass heat treated at 693 K was measured by impedance spectroscopy method.
-
Critical Field and Specific Heat in Electron- and Hole-Doped Graphene Superconductors
Publication -
High temperature corrosion of evaporator tubes with thermal sprayed coatings
PublicationDegradation examinations of outer surface of low-emission steam boiler evaporator tubes are presented in the paper. Metallographic evaluation of scale morphology, its micro sites chemical composition analysis and distribution of elements on cross sections have been performed. Water-wall tubes were exposed in steam boiler for up to two years period. Common tubes made of 16Mo3 steel suffered sulphide and molten salts corrosions....
-
Finding Temperature Distribution at Heat Recovery Unit Using Genetic Algorithms
Publication -
Field investigation on seawater temperature variability in relation to horizontal optical gradient
Publication -
Numerical analysis of the influence of combustible material on the temperature field during fire
Publication -
Flow visualization and heat transfer investigations on the flat plate with streamwise pressure gradient
PublicationPaper presents experimental investigations results for film cooling on a flat plate. The main objective of the design is the streamwise pressure distribution on the flat plate as in the blade cascade. The transient and steady-state technique with liquid crystals for the surface temperature distribution with film cooling has been used in experiments in a low speed wind tunnel.
-
The effect of plate size on the natural convective heat transfer intensity of horizontal surfaces
PublicationW pracy przedstawiono badania wpływu rozmiarów płyty prostokątnej poziomej na intensywność wymiany ciepła w warunkach konwekcji swobodnej. Zaproponowano dwa zakresy: dla płyt o wymiarze charakterystycznym mniejszym niż 0,1 m - 0,2 m intensywność konwekcyjnej wymiany ciepła jest odwrotnie proporcjonalna do szerokości płyty, dla płyt szerszych niż 0,2 m szerokość płyty nie wpływa znacząco na współczynnik konwekcyjnej wymiany ciepła....
-
Influence of porous coating on heat transfer during R22 and R134a flow boiling.
PublicationPrzedstawiono wpływ powłoki porowatej na przenoszenie ciepła i spadku ciśnienia podczas wrzenia w przepływie czynników chłodniczych, R22 i R134a.
-
Influence of pressure on heat transfer during pool boiling on smooth tube bundle
PublicationPrzedstawiono wyniki badań eksperymentalnych wrzenia wody, metanolu i R141b na pęu rur głądkich w warunkach podcisnienia i ciśnienia atmosferycznego
-
Experimental study of flow pattern and heat transfer during steam drying of wood
PublicationBadania wysokotemperaturowego suszenia drewna zostały zainspirowane koniecznością instensyfikacji wymiany ciepła i masy na potrzeby przemysłu drzewnego, a w szczególności meblarskiego, w zakresie doskonalenia metod suszenia drewna, modelowania intensyfikacji wymiany ciepła i masy w elementach suszonych, opracowania ekologicznych i energooszczędnych systemów suszarniczych, ochrony środowiska związanej z racjonalnym zużyciem energii,...
-
Prediction of flow boiling heat transfer data for R134a, R600a and R290 in minichannels
PublicationIn the paper presented is the analysis of the results of calculations using a model to predict flow boiling of refrigerants such as R134a, R600a and R290. The latter two fluids were not used in development of model semiempirical correction. For that reason the model was verified with present experimental data. The experimental research was conducted for a full range of quality variation and a relatively wide range of mass velocity....
-
Heat transfer enhancement, flow visualization and friction characteristics in rib-roughened channels
PublicationW pracy przedstawiono wyniki badań eksperymentalnych związanych z intensyfikacją wymiany ciepła w kanałach wyposażonych w żebra, które poprawiają warunki przejmowania ciepła od ścianki do przepływającego medium. W badaniach wykorzystano system PIV oraz termografię ciekłokrystaliczną.
-
Experimental Investigation of an Intensified Heat Transfer Adsorption Bed (IHTAB) Reactor Prototype
Publication -
Turbulence model evaluation for numerical modelling of turbulent flow and heat transfer of nanofluids
PublicationIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (Reynolds number between 6000 and 12000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
Theoretical and experimental research of heat and mass transfer in adsorption process in dac systems
PublicationPrzedstawiono badania wymiany ciepła i masy w stałych adsorpcyjnych elementach wykonanych na bazie silikażelu. Zaprezentowano również informacje dotyczące osuszania w systemach klimatyzacyjnych. Na zkończenie pokazano wyniki numerycznej symulacji i skojarzonej wymiany ciepła i masy w chłodzonym osuszaczu.
-
Influence of rotating magnetic field on gas-liquid volumetric mass transfer coefficient
Publication -
Gas to liquid mass transfer in mixing system with application of rotating magnetic field
Publication -
Non-Destructive Testing of the Longest Span Soil-Steel Bridge in Europe—Field Measurements and FEM Calculations
PublicationThe article describes interdisciplinary and comprehensive non-destructive diagnostic tests of final bridge inspection and acceptance proposed for a soil-steel bridge made of corrugated sheets, being the European span length record holder (25.74 m). As an effect of an original concept a detailed and precise information about the structure short-term response was collected. Periodic diagnostics of bridge deformations was done one...
-
Tropospheric thermal field variability over Poland in the context of climate change
Publication -
Online Volatile Compound Emissions Analysis Using a Microchamber/Thermal Extractor Coupled to Proton Transfer Reaction-Mass Spectrometry
PublicationIndoor air is a complex and dynamic mixture comprising manifold volatile organic compounds (VOCs) that may cause physiological and/or psychological discomfort, depending on the nature of exposure. This technical note presents a novel approach to analyze VOC emissions by coupling a microchamber/thermal extractor (μ-CTE) system to a proton transfer reaction-mass spectrometer (PTR-MS). This configuration provides an alternative to...
-
The thermodynamic critical field and specific heat of superconducting state in phosphorene under strain
Publication -
SEM images of symmetrical cell interface with SrTi0.30Fe0.70O3-d electrode and CGO-20 substrate in function of sintering temperature
Open Research DataThis dataset contains images of polished cross section of symmetrical cell interface with SrTi0.30Fe0.70O3-d electrode and CGO-20 substrate in function of sintering temperature (800 °C, 900°C and 1000 °C) . Images were obtained using a PhenomXL (Thermo Fisher Scientific, the Netherlands) scanning electron microscope (SEM) with an accelerating voltage...
-
SEM images of symmetrical cell interface with SrTi0.65Fe0.35O3-d electrode and CGO-20 substrate in function of sintering temperature
Open Research DataThis dataset contains images of polished cross section of symmetrical cell interface with SrTi0.65Fe0.35O3-d electrode and CGO-20 substrate in function of sintering temperature (800 °C, 900°C and 1000 °C) . Images were obtained using a PhenomXL (Thermo Fisher Scientific, the Netherlands) scanning electron microscope (SEM) with an accelerating voltage...
-
SEM images of symmetrical cell interface with SrTi0.50Fe0.50O3-d electrode and CGO-20 substrate in function of sintering temperature
Open Research DataThis dataset contains images of polished cross section of symmetrical cell interface with SrTi0.50Fe0.50O3-d electrode and CGO-20 substrate in function of sintering temperature (800 °C, 900°C and 1000 °C) . Images were obtained using a PhenomXL (Thermo Fisher Scientific, the Netherlands) scanning electron microscope (SEM) with an accelerating voltage...
-
Chapter 1. Modelling of temperature field of cylindrical pool boiling heating section
PublicationPoddano analizie fundamentalny problem określania temperatury powierzchni, na której zachodzi wrzenie. Rozpatrzono dwa przypadki ogrzewania sekcji: z zastosowaniem grzejnika patronowego oraz użyciem sekcji jako elementu oporowego. Sformułowano i rozwiązano zagadnienia brzegowe 1D, 2D ORAZ 3D. Przedstawiono wyniki obliczeń numerycznych z zastosowaniem MES.
-
Modelling of temperature field of flat boiling section with active single nucleation site
PublicationZaprezentowano główne założenia wybranych modeli wrzenia dla pojedynczego centrum nukleacji. Przedstawiony model numeryczny dotyczy zagadnienia dwuwymiarowego, osiowo-symetrycznego, nieizotropowego przewodzenia ciepła dla warunków brzegowych pierwszego, drugiego i trzeciego rodzaju. Warunek brzegowy drugiego rodzaju reprezentuje gęstość strumienia ciepła połączoną z generacją pęcherzy z pojedynczego centrum nukleacji.
-
Nonlinear impedance as a function of A.C. voltage for fully crystallized 35Bi2VO5.5-65SrB4O7 glass measured with impedance spectroscopy method at high temperature region
Open Research DataThe nonlinear electrcial properties as a function of A.C. voltage for fully crystallized 35Bi2VO5.5-65SrB4O7 glass was measured by impedance spectroscopy method.
-
Nonlinear impedance as a function of A.C. voltage for fully crystallized 45Bi2VO5.5-55SrB4O7 glass measured with impedance spectroscopy method at high temperature region
Open Research DataThe nonlinear electrcial properties as a function of A.C. voltage for fully crystallized 45Bi2VO5.5-55SrB4O7 glass was measured by impedance spectroscopy method.
-
Jeffreys heat conduction in coupled semispaces subjected to interfacial heating
PublicationA Jeffreys heat conduction problem for coupled semispaces subjected to the action of an interfacial heat source was defined. An analytical solution of the problem was derived for a polynomial specific power of the heat source using the Laplace transform approach. The asymptotic and parametric analysis was performed for different ratios of thermal conductivities , thermal diffusivities , thermal relaxation times and coefficients...
-
Natural convective heat transfer from isothermal horizontal, vertical and inclined plates - a review
PublicationW artykule przedstawiono przegląd otrzymanych przez różnych badaczy korelacji eksperymentalych, teoretycznych i numerycznych, opisujących wymianę ciepła od izotermicznych płyt o różnym kącie pochylenia. Przedstawiono model matematyczny zjawiska. Opisano stosowane metody badawcze i wskazano przyczyny rozbieżności pomiędzy przedstawionymi przez wielu autorów wynikami.
-
The use of liquid crystal thermography and particle image velocimetry in the exploration of heat transfer measurements
PublicationArtykuł dotyczy badań eksperymentalnych wymiany ciepła w modelowym wymienniku ciepła z turbulizatorami przepływu przy użyciu termografii ciekłokrystalicznej i cyfrowej anemometrii obrazowej.
-
Heat Transfer Augmentation through Different Jet Impingement Techniques: A State-of-the-Art Review
Publication -
Determination of heat transfer coefficient in evaporator of the organic Rankine cycle using the Wilson method.
PublicationW pracy zastosowano metodę Wilsona do wyznaczania współczynnika przejmowania ciepła. Przedmiotem rozważań jest płytowy wymiennik ciepła pracujący jako parownik w laboratoryjnym stanowisku realizującym obieg ORC. Wykorzystana metoda jest metodą wydajną w przypadku wymienników ciepła o złożonej geometrii i dużej liczbie kanałów, dla których pomiar temperatury ścianki jest niemożliwy, a przez to określenie współczynników przejmowania...
-
Nucleate pool boiling heat transfer from small horizontal smooth tube bundles
PublicationPrzedstawiono wyniki pomiarów współczynnika przejmowania ciepła podczas wrzenia wody destylowanej, metanolu i R141b na poziomym pęku rur gładkich, który składał się z 19 rurek, ogrzewanych elektrycznie, w układzie przestawionym i podziałce 1.7d oraz 2.0d. Wyznaczono również wartości współczynnika wpływu pęku. Podano równanie korelacyjne do obliczania średniego współczynnika przejmowania ciepła
-
Intensyfikacja wymiany ciepła przy pomocy mikrostrug = Heat transfer intensification using microjets.
PublicationW pracy przedstawiono wyniki badań eksperymentalnych nad intensyfikacją strumienia ciepła przy pomocy pojedynczej mikrostrugi wody. W pracy przedstawiono wyniki badań dla dysz o średnicy 180 i 280 mikrometrów.