Search
Search results for: FINISHING BY BALL BURNISHING
-
Surface Texture Analysis of Hardened Shafts after Ceramic Ball Burnishing
PublicationThis article represents the results of testing the surface condition of shafts manufactured by the burnishing process. The shafts with a hardness of approximately 62 HRC (Rockwell C). were burnished with a ceramic ball (Si3N4), where the force range was controlled by the means of a hydraulic system. The machining process consisted of hard turning shafts with cubic boron nitride (CBN) inserts, followed by burnishing with the use...
-
EVALUATION OF SURFACE ROUGHNESS PARAMETERS OF TURNED GEAR WHEELS HOLES MACHINED BY BALL BURNISHING
PublicationW artykule zaprezentowano wyniki z badań eksperymentalnych dotyczących przygotowania powierzchni do obróbki wykończeniowej nagniataniem. Badania dotyczyły obróbki materiałów w stanie utwardzonym po hartowaniu. analizowano wpływ parametrów toczenia na twardo na uzyskiwane wartości parametrów chropowatości powierzchni jako wejściowych przed procesem nagniatania.
-
The estimation of cutting forces and specific force coefficients during finishing ball end milling of inclined surfaces
Publication -
Roller burnishing
PublicationThe paper shows the process of roller burnishing as a method of finishing machine components. Based on own research the author presents the effects of the roller burnishing process to increase the hardness and residual stress as well as the wear and fatigue strength of burnishing components.
-
The Roughness of the Hardened Steel Surface Created by the Rolling-Burnishing Process
PublicationBurnishing hard materials can be used as an alternative finishing process. this paper presents the results of burnishing hardened steel. The article discusses surface deformation that occurs during this process and depends on the selected parameters of the geometric structure of the force applied for surface burnishing.
-
Wpływ posuwu nagniatania na chropowatość powierzchni przedmiotów ze stali w stanie utwardzonym
PublicationPrzedstawiono wyniki badań eksperymentalnych procesu nagniatania stali twardej (62 HRC) narzędziem ceramicznym (kulką) z dociskiem hydrostatycznym. Analizowano wpływ posuwu nagniatania oraz parametrów poprzedzającej obróbki toczeniem na twardo na stan powierzchni opisanej wybranymi parametrami chropowatości.
-
Studies on the influence of technological variants of finishing machining on flow of parts in flexible manufacturing
PublicationIn the article below the problems of influence of variants of finishing processing on flow of machining parts in flexible manufacturing system were presented. The investigations were carried out the technological processes for piston rods and rams of hydraulic cylinders. There were also presented model variants of technological processes for piston rods finished with the burnishing. In these studies the influence of technological...
-
The influence of variants of finishing machining on scheduling of shaft components manufacturing
PublicationIn the paper variants of technological processes were presented to the study for piston rods and rams of hydraulic cylinders taking issues into consideration scheduling of course of the production in flexible manufacturing cell. At the carried study an attempt of the estimation of the influence of technological variants on the effectiveness to manufacture the flexible manufacturing system on the basis of preliminary schedules of...
-
The effect of an active force while slide diamond burnishing of wooden shafts upon process quality
PublicationThe quality of the surface of wooden elements that have been turned and burnished has got a crucial meaning in the whole production process flow, since the obtained effects affect the quality of the wooden surface after finishing (coating, painting). In the paper, selected results of the investigation of the effect of the burnishing process on the surface quality of the elements after turning are presented. Research experiments...
-
Problems of Flaking in Strengthening Shaft Burnishing
PublicationThe article presents the results of testing the surface condition of shafts manufactured by a strengthening rolling burnishing process. The shafts with a hardness about 220 HB were burnished with a roller with different force. Researches were carried out with particular attention to the structure of the outflowing material in the tool zone during burnishing process. The article presents the results of the examinations of burnished...
-
Rotating rod and ball
PublicationWe consider a mechanical system consisting of an infinite rod (a straight line) and a ball (a massless point) on the plane. The rod rotates uniformly around one of its points. The ball is reflected elastically when colliding with the rod and moves freely between consecutive hits. A sliding motion along the rod is also allowed. We prove the existence and uniqueness of the motion with a given position and velocity at a certain time...
-
Sliding burnishing technology of holes in hardened steel
PublicationNew technology with sliding burnishing of holes with cylindrical surface, made of hardened steel /60 HRC/, is presented in the paper.After burnishing operation on hole diameter 30 mm in satellite gear wheel the surface roughness parameter Ra=0,02-0,04 micrometers was obtained. The method and results of research as technological conclusion are presented.
-
Hybrid Processing by Turning and Burnishing of Machine Components
PublicationThe paper presents a method of hybrid manufacturing process of long 5 shafts and deep holes by simultaneous turning and burnishing method. The tech- 6 nological results of the research focus on the influence of the basic technological 7 parameters of this process on the surface roughness of piston rods of hydraulic 8 cylinders. Research results are presented in the graphs as well as mathematical 9 formula. Set of samples were made...
-
Jumping Wave Characteristic during Low Plasticity Burnishing Process
PublicationDuring the low plasticity burnishing process of soft materials such as carbon steel with a hardness of up to 40 HRC (Rockwell grade) a raised structure of the material known as the Jumping Wave forms in front of the tool roll. This phenomenon significantly disturbs the burnishing process, but is very poorly described in the literature. This article presents studies of this phenomenon on the example of burnished 1.0562 steel. The...
-
Integrated production technology of cylindrical surfaces by turning and burnishing
PublicationThe method is based on a combination of previously used two separate operations namely machining and burnishing in a one complex operation implemented on a lathe.In the case of machining shafts and hydraulic cylinders of steel C45 is possible to obtain a surface roughness Ra=0,16 - 0,32 micrometers, dimensional accuracy class 7-8 according to ISO standards, and increase in the hardness of the surface up to 40%.
-
Ball milling induced borophene flakes fabrication
PublicationTo fill the knowledge gap for borophene, as the youngest member of the two-dimensional (2D)nanomaterials family, a facile, cost effective, scalable and reproducible fabrication route is still stronglyrequired. Among so far studied techniques the potential of pure mechanical processes such as ballmilling is not explored yet. Therefore, in this contribution, we explore the efficiency...
-
Novel Nonlinear High Order Technologies for Damage Diagnosis of Complex Assets
PublicationFor the first time worldwide, innovative techniques, generic non-linear higher-order unnormalized cross-correlations of spectral moduli, for the diagnosis of complex assets, are proposed. The normalization of the proposed techniques is based on the absolute central moments, that have been proposed and widely investigated in mathematical works. The existing higher-order, crosscovariances of complex spectral components are not sufficiently...
-
Novel Fault Identification for Electromechanical Systems via Spectral Technique and Electrical Data Processing
PublicationIt is proposed, developed, investigated, and validated by experiments and modelling for the first time in worldwide terms new data processing technologies, higher order spectral multiple correlation technologies for fault identification for electromechanical systems via electrical data processing. Investigation of the higher order spectral triple correlation technology via modelling has shown that the proposed data processing technology...
-
Properties of surface layers of duplex stainless steel after burnishing processes
PublicationStress corrosion cracking resistance of cold worked layers of 25 Cr duplex stainless steel grade UR52N+ has been investigated. The surface layers were performed through burnishing treatment. The residual stresses at surface layers were determined using grazing angle incidence X-ray diffraction method (g-sin2 Ψ). Corrosion tests were performed with the use of Slow Strain Rate Test technique in boiling 35% MgCl2 solution. It has...
-
Hardened Steel Surface Waviness Created by Rolling Burnishing Process
PublicationThe surface of the finishing machined parts is defined mainly by roughness parameters. Growing demands on the part, especially mating sliding or rolling, require the specification of additional parameters, such as waviness parameters, particularly when there is significant resistance to seizing or noise reduction. This paper presents surface waviness characteristics of hardened burnished steel.
-
The Possibilities of Improving the Fatigue Durabilityof the Ship Propeller Shaft by Burnishing Process
PublicationHeavily loaded structural elements operating in a corrosive environment are usuallyquickly destroyed. An example of such an element is a ship propeller operating in a seawaterenvironment. This research presents a fatigue resistance test performed on elements operating inseawater. Different processing parameters applied on the samples in particular were compared withthe specimens whose surface had been burnished differently and...
-
Tools for finishing processes on hard materials
PublicationPrzedstawiono narzędzia i wyniki obróbki materiałów w stanie twardym. Analizowano proces docierania elementów ceramicznych mikroziarnami diamentowymi, nagniatanie stali w stanie twardym (60 HRC) kulkami z Si3N4 i przecinanie ściernicowe stali ŁH15 (62 HRC).
-
Smoothing of wood surface by burnishing
PublicationW artykule zaprezentowano rozwój bezwiórowych metod obróbki wykańczającej drewna. Przedstawiono wpływ nagniatania ślizgowego na chropowatość powierzchni drewna. Badania przeprowadzono na próbkach wykonanych z drzewa sosnowego toczonych i nagniatanych ślizgowo. Nagniatanie ślizgowe przeprowadzono z wykorzystaniem nagniataka elastycznego o elemencie ślizgowym wykonanym z Karbonado. Wyniki odniesiono do głównych parametrów nagniatania...
-
PLATING AND SURFACE FINISHING
Journals -
Rotating rod and ball
Publication -
Finishing of Ceramics in a Single-Disk Lapping Machine Configuration
PublicationPrzedstawiono metodę obróbki ceramiki technicznej na zmodifikowanej docierarce jednotarczowej z niezależnym napędem pierścienia prowadzącego. Omówiono przebieg obróbki z wykorzystaniem nowych narzędzi i zastosowaniem ziarna wiązanego.
-
Tailoring a low-energy ball milled MnCo2O4 spinel catalyst to boost oxygen evolution reaction performance
PublicationThe development of cost-efficient oxygen evolution reaction (OER) catalysts is one of the most important tasks facing modern techniques for hydrogen production. In this work, for the first time, a low-energy ball milling process of MnCo2O4 (MCO) spinel powders, with a mechanical modification time exceeding 1 day was used. After 6 days of ball-milling, the obtained overpotential of the electrocatalyst reached the value of 375 mV...
-
WEAR TESTING OF DLC COATINGS WITH FRICTION COUPLE „BALL-ON-DISK” = Badania zużycia powłok DLC w skojarzeniu kula-tarcza obrotowa ''ball-on-disk''
PublicationW Katedrze Konstrukcji i Eksploatacji Maszyn PG opracowano metodę badania powłok DLC oraz innych (ceramicznych) w układzie kula - płaska powierzchnia obrotowej tarczy ("ball-on-disk"). Układ badawczy składa się z kuli osadzonej w popychaczu łożyskowanym tocznie, poprzez który wywierana jest siła docisku próbek. Kula dociskana jest od góry do płaskiej powierzchni obrotowej tarczy - próbki dolnej (o pionowej osi obrotu). Próbka dolna...
-
Optimal spindle speed determination for vibration reduction during ball-end milling of flexible details
PublicationIn the paper a method of optimal spindle speed determination for vibration reduction during ball-end milling of flexible details is proposed. In order to reduce vibration level, an original procedure of the spindle speed optimisation, based on the Liao–Young criterion, is suggested. As the result, an optimal, constant spindle speed value is determined. For this purpose, on-stationary computational model of machining process is...
-
Surface vaviness of components machined by burnishing method
PublicationPowierzchnię po obróbce wykończeniowej definiuje się zazwyczaj za pomocą parametrów chropowatości. Rosnące wymagania jakościowe w stosunku do wytwarzanych części maszyn powodują rozszerzanie się zakresu parametrów opisujących powierzchnię. W artykule przedstawiono ocenę jakościową powierzchni nagniatanych za pomocą parametrów falistości.
-
Formation of wood surface roughness in burnishing process
PublicationW publikacji przedstawiono i omówiono rozwój bezwiórowych metod obróbki wykańczającej drewna przez nagniatanie. Przedstawiono wpływ nagniatania na chropowatość powierzchni drewna. Badania przeprowadzono na próbkach toczonych i nagniatanych. Wyniki odniesiono do głównych parametrów nagniatania jak: siła nagniatania oraz promień zaokrąglenia elementu nagniatającego.
-
Surface quality of the plasma cermet coatings after grind finishing
Publication -
Tripped at the Finishing Line: The Åland Islands Internet Voting Project
PublicationThe Åland Islands spent years preparing an internet voting system, to be implemented for the first time in October 2019 for Parliamentary Elections. Despite this, the project was canceled the evening before the expected release date. In this paper, we explore the causes of this failure using a two-pronged approach including Information System failure perspectives and the approach to e-voting Mirabilis, focusing on organizational...
-
Ball milling treatment of Mn3O4 regulates electron transfer pathway for peroxymonosulfate activation
PublicationHeterogeneous metal catalysts have attracted considerable interest in advanced oxidation processes (AOPs) for wastewater treatment by activating peroxymonosulfate (PMS). However, it remains challenging to the rational design of efficient reaction pathway for high-performance contaminants removal by regulating the inherent structure of metal oxides. Herein, a high-energy ball milling method was employed to modulate the electronic...
-
Ways to implement hybrid finishing technology with a hand-held rotary tool
Publication -
Influence of finishing colour on the efficiency of automated production line for wooden doors
PublicationPorta KMI Poland S.A. company has implemented a fully automated intelligent technological line TechnoPORTA for customized mass-production of technical door leaves. Each door leaf is provided with a unique QR code. It allows the line modules to individually adjust the machining parameters to the currently processed element according to the IT controlling system. Before en-tering the TechnoPorta line, the door leaves are not sorted,...
-
Convenient and efficient N-methylation of secondary amines under solvent-free ball milling conditions
PublicationIn the present work, we report the development of a rapid, efcient, and solvent-free procedure for the N-methylation of secondary amines under mechanochemical conditions. After optimization of the milling parameters, a vibrational ball mill was used to synthesize 26 tertiary N-methylated amine derivatives in a short time of 20 min (30 Hz frequency) and high yields ranging from 78 to 95%. An exception was compounds having a hydroxyl...
-
The surface contact characteristics after sliding and rolling burnishing.
PublicationW pracy przedstawiono zastosowanie nowej metody SCGC i odpowiedniego programu komputerowego JKC do oceny pomierzonej mikrostereometrii powierzchni części maszyn, głównie na potrzeby kontroli jakości. Na przykładzie powierzchni nagniatanych wykazano cechy nowej metody: wizualizację ułatwiającą wyobrażenie pomierzonej sfery chropowatości, położenie w niej najważniejszych parametrów oceny (rozkład geometrycznej powierzchni kontaktu,...
-
Application of ceramic and composite tools in smoothing burnishing process.
PublicationArtykuł zawiera oryginalne konstrukcje narzędzi nagniatających. Elementy nagniatające zostały wykonane z ceramiki i kompozytu ''Karbonado''. Narzędzia te mogą być stosowane na obrabiarkach CNC i centrach obróbkowych, zwłaszcza do obróbki stali hartowanych. Artykuł przedstawia również wyniki badań i przykłady zastosowań tych narzędzi w przemyśle.
-
New ceramic and composite tools for smoothing burnishing process
PublicationW pracy przedstawiono nowe konstrukcje narzędzi ceramicznych i z kompozytu karbonado do nagniatania twardych hartowanych stali. Zamieszczono wyniki badań wpływu parametrów technologicznych nagniatania walcowych próbek ze stali 45 o różnej twardości 23-56HRC na chropowatość powierzchni próbek.
-
Development and importance of burnishing technology in computer integrated manufacturing
PublicationPrzedstawiono podstawy odkształcania nierówności powierzchni w wyniku różnych odmian procesu nagniatania. Opisano oryginalne technologie nagniatania i narzędzia dla następujących sposobów nagniatania: krążkowanie z dociskiem sztywnym i elastycznym, toczenie z jednoczesnym nagniataniem powierzchni zewnętrznych walcowych, nagniatanie elektromechaniczne, ślizgowe narzędziem diamentowym i oscylacyjne. Podano zalecane parametry obróbki...
-
ALTERNATIVE, DIRECT SYNTHESIS METHOD OF THE CERAMIC SOLID SOLUTIONS BASED ON BaTiO3 THROUGH A HIGH ENERGY BALL MILLING
PublicationPolycrystalline samples BaTiO3 and the solid solutions Ba0.9Sr0.1TiO3, Ba0.9Sr0.1Ti0.9Sn0.1O3, Ba0.9Sr0.1Ti0.8Sn0.2O3 were obtained by means of a mechanochemical treatment based on the high-energy ball milling technique and next a high temperature solid state reaction method. The influence of synthesis condition on microstructural, dielectric and ferroelectric properties of obtained solid solutions were investigated. The structure...
-
Influence of burnishing on stress corrosion cracking susceptibility of duplex steel
PublicationNa próbkach ze stali duplex poddanych procesom nagniatania przeprowadzono badania podatności do naprężeniowego pękania korozyjnego. Przeprowadzono testy odkształcania z małą prędkością w środowisku wrzącego 35% MgCl2 i środowisku obojętnym- glicerynie. Stwierdzono zwiększoną odporność korozyjną stali po procesach nagniatania z niewielkim stopniem zgniotu. Stwierdzono, że zgniot powierzchniowy ma wpływ na przebieg procesu korozyjnego...
-
Technological and tribological aspects of milling-burnishing process of complex surfaces
Publication -
LOW PLACTICITY BURNISHING PROCESSES. Fundaments, tools and machine tools
PublicationW obszernej monografii (530 stron) autor przedstawił w sposób kompleksowy zagadnienia związane z wykończeniową metodą obróbki części maszyn przez powierzchniową obróbkę plastyczną-nagniataniem. Jest to pierwsza książka w języku angielskim poświęcona tej bezwiórowej i ekologicznej metodzie obróbki. W wielu przypadkach w technologii różnorodnych części maszyn i innych urządzeń, nagniatanie może zastąpić operację szlifowania. Ma to...
-
Novel Investigation of Higher Order Spectral Technologies for Fault Diagnosis of Motor-Based Rotating Machinery
PublicationIn the last decade, research centered around the fault diagnosis of rotating machinery using non-contact techniques has been significantly on the rise. For the first time worldwide, innovative techniques for the diagnosis of rotating machinery, based on electrical motors, including generic, nonlinear, higher-order cross-correlations of spectral moduli of the third and fourth order (CCSM3 and CCSM4, respectively), have been comprehensively...
-
Multi-objective optimization of tool wear, surface roughness, and material removal rate in finishing honing processes using adaptive neural fuzzy inference systems
PublicationHoning processes are usually employed to manufacture combustion engine cylinders and hydraulic cylinders. A crosshatch pattern is obtained that favors the oil flow. In this paper, Adaptive Neural Fuzzy Inference System (ANFIS) models were obtained for tool wear, average roughness Ra, cylindricity and material removal rate in finish honing processes. In addition, multi-objective optimization with the desirability function method...
-
Ball on disk test AT4_11-Al2O3-r25
Open Research DataHard particle reinforced Al6061 alloy testing. Laser remelting and kinetic injection of particulate material. Ball on disc tribological test. Ball material: Al2O3. Ball diameter: 5 mm. Sliding path radius: 25 mm. Disk material: Al6061 TiN powder injected (AT4_11).
-
Ball on disk test AT3_21-Al2O3-r25
Open Research DataHard particle reinforced Al6061 alloy testing. Laser remelting and kinetic injection of particulate material. Ball on disc tribological test. Ball material: Al2O3. Ball diameter: 5 mm. Sliding path radius: 25 mm. Disk material: Al6061 TiN powder injected (AT3_21).
-
Ball on disk test AW4_1-Al2O3-r15
Open Research DataHard particle reinforced Al6061 alloy testing. Laser remelting and kinetic injection of particulate material. Ball on disc tribological test. Ball material: Al2O3. Ball diameter: 5 mm. Sliding path radius: 15 mm. Disk material: Al6061 WC powder injected (AW4_1).