Filters
total: 1258
-
Catalog
displaying 1000 best results Help
Search results for: PIPE ROOFING
-
The low temperature waste heat recovery in drying process of pine wood using micro-jet heat exchanger
PublicationThe article presents the influence of the drying medium temperature changes for the relative and absolute moisture content values during pine wood drying. The drying process was conducted at constant atmospheric pressure and with different drying medium (air) temperature levels, respectively: 40oC, 60oC, 80oC, 100oC, and 120oC. In order to develop a method that would enable low temperature drying of solid materials the experiments...
-
Predicting cutting power for band sawing process of pine and beech wood dried with the use of four different methods
PublicationWood drying is an important stage in the woodworking process. After drying, wood is subject to a re-sawing process, for which a high quality surface, low material loss, and high efficiency are often required. In this paper, forecasted values were presented of cutting power for the re-sawing process of pine and beech wood that were dried with four different methods. Forecasting of cutting power for an industrial band saw machine...
-
Image Representation for Cognitive Systems Using SOEKS and DDNA: A Case Study for PPE Compliance
PublicationCognitive Vision Systems have gained significant interest from academia and industry during the past few decade, and one of the main reasons behind this is the potential of such technologies to revolutionize human life as they intend to work under complex visual scenes, adapting to a comprehensive range of unforeseen changes, and exhibiting prospective behavior. The combination of these properties aims to mimic the human capabilities...
-
Spatial distribution of CO2, O2, CO, NO and temperature within a biowaste composting pile
Open Research DataThe dataset contains the color-coded isophlets illustrating the spatial distribution of gas concentrations (CO, CO2, O2 and NO) and the temperature in biowaste composting pile during 6 weeks of process. Four cross sections and two longitudinal cross sections (the left and right sides of the pile) were made using Surfer 10 software (Golden Software,...
-
COMPARISON OF HEAT TRANSFER CHARACTERISTICS IN SURFACE COOLING WITH BOILING MICROJETS OF WATER, ETHANOL AND HFE7100
PublicationThe basis of microjet technology is to produce laminar jets which when impinging the surface have a very high kinetic energy at the stagnation point. Boundary layer is not formed in those conditions, while the area of film cooling has a very high turbulence resulting from a very high heat transfer coefficient. Applied technology of jet production can result with the size of jets ranging from 20 to 500μm in breadth and 20 to 100μm...
-
Evaluation of Vehicle Routing Problem Algorithms for Transport Logistics Using Dedicated GIS System
PublicationThe development and research related to optimization of fleet management is of high interest among many industrial and scientific entities related to logistics and transport. Optimal distribution of transportation resources leads to significant cost reduction. In this context, scientific research related to so called Vehicle Routing Problem (VRP) which relies on determining the shortest transport routes for a strictly limited number...
-
Effect on Phytochemical Content and Microbial Contamination of Actinidia Fruit after Shock Cooling and Storage
Publication -
Interaction of Acoustic and Thermal Modes in the Gas with Nonequilibrium Chemical Reactions: Possibilities of Acoustic Cooling
PublicationNonlinear generation of thermal mode during propagation of dominative sound in a chemically reacting gas is considered. The dynamic equation of excess temperature associated with the thermal mode is derived. It is instantaneous and includes quadratic nonlinear acoustic source reflecting the nonlinear character of interaction between acoustic and non-acoustic types of gas motion. Both periodic and aperiodic sound may be considered...
-
Comparison of heat transfer characteristics in surface cooling with boiling microjets of water, ethanol and HFE7100
PublicationThe basis of microjet technology is to produce jets which impinge the surface at the stagnation point with a very high kinetic energy. Main objective of this paper was to investigate the physical phenomena occurring on solid surfaces upon impingement of the single microjet in case of three fluids, namely water, ethanol and HFE7100. Intense heat transfer in the impact zone of microjet has been examined and described with precise...
-
THE INFLUENCE OF DIFFERENT VEGETABLE DISPERSION PHASES ON THE ROLLING CONTACT FATIGUE OF BIODEGRADABLE LUBRICATING GREASES
Publication -
Numerical investigations of the engine cooling system in a small power vesel pod propulsion system
PublicationThe development of electronics and electrotechnology enabled to put electric motors of the alternating current in the pod and to use them for the main drive of ships. A lot of heat which must be picked up from the system is a problem which is turning up at applying the system of this type. Many big ships lately contended with these problems. Building the small propeller for the boat powered with solar power we decided to check...
-
Evaluation of turning with different cooling-lubricating techniques in terms of surface integrity and tribologic properties
Publication -
Water Demineralization by Membrane Distillation Utilizing Cooling Water From Municipal Waste Incinerator
Publication -
Timed rolling and rising tests in Duchenne muscular dystrophy ambulant boys: a feasibility study
PublicationBACKGROUND: Functional activities are extensively used in motor assessments of patients with Duchenne muscular dystrophy. The role of timed items has been reported as an early prognostic factor for disease progression. However, there are two functional activities that are not widely assessed in clinical practice among Duchenne muscular dystrophy patients: rolling and bed rising. This study aimed to investigate whether the 360-degree...
-
The impact of footing conditions of a vertical-axis floating-roof tank on structural shell deformation
PublicationStructural shells of fuel tanks are often subjected to geometric imperfections which may lead to exceeding the ultimate and serviceability limit states. One of the means triggering shell deformation is non-uniform settlement caused by incoherent soil conditions. Analysis carried out in the work concerns of vertical-axis, floating-roof cylindrical shell which volume is 50.000 m3, founded on a complex multi-layered soil. The sensitivity...
-
Heat exchange enhancement of jet impingement cooling with the novel humped-cone heat sink
PublicationJet impingement cooling technology is applicable to control temperature of devices, where very high heat flux is generated within a small area. This paper is about the improvement of the jet impingement cooling efficiency by the heat sink geometry modification. Two reference cases were sourced from the literature – flat heat sink and modified one with cone in the jet stagnation region. Such a change improves cooling capability...
-
Ship weather routing optimization with dynamic constraints based on reliable synchronous roll prediction
PublicationShip routing process taking into account weather conditions is a constrained multi-objective optimization problem and it should consider various optimization criteria and constraints. Formulation of a stability-related, dynamic route optimization constraint is presented in this paper. One of the key objectives of a cross ocean sailing is finding a compromise between ship safety and economics of operation. This compromise should...
-
Distributed Inter-Domain Link Capacity Optimization for Inter-Domain IP/MPLS Routing
Publication -
Influence of steam cooking on pro-health properties of Small and Large variety of Momordica charantia
PublicationSteam cooking is one of the most common preparations of Momordicacharantia dishes. This method improved the tastiness of the fruits but at the same time, some changes occurred in the volatile and non-volatile parts of their food matrices. In this study, for the first time these properties were correlated with the found substances affecting the bioactivity of this fruit. Two varieties of Momordicacharantia were analysed and compared....
-
A study of jet impingement cooling enhancement by concave and convex heat sink shape modifications
PublicationThe rising demand for efficient cooling technologies is a strong driver of extensive research in this area. This trend is particularly strong in turbines and microprocessors technology. Presented study is focused on the jet impingement cooling concept, which is used in various configurations for many years. The potential of the heat sink shape modification is not yet fully explored. Available literature suggests that average Nusselt...
-
Weather Hazard Avoidance in Modeling Safety of Motor-Driven Ship for Multicriteria Weather Routing
PublicationWeather routing methods find the most suitable ocean?s route for a vessel, taking into account changeable weather conditions and navigational constraints. In the multicriteria approach based on the evolutionary SPEA algorithm one is able to consider a few constrained criteria simultaneously. The approach applied for a ship with hybrid propulsions has already been presented by one of the authors on previous TransNav?2009. This time...
-
IMPLEMENTATION OF THE POST-SYNODAL APOSTOLIC EXHORTATION "AMORIS LAETITIA" OF POPE FRANCIS IN THE PASTORAL CARE OF IRREGULAR SITUATIONS IN THE DIOCESE OF PŁOCK
Publication -
Fatigue damage development in 10CrMo9-10 steel for power plant pipes in as-received state and after 280,000 h of exploitation
Publication -
Influence of Installation Effects on Pile Bearing Capacity in Cohesive Soils – Large Deformation Analysis Via Finite Element Method
PublicationIn this paper, the whole process of pile construction and performance during loading is modelled via large deformation finite element methods such as Coupled Eulerian Lagrangian (CEL) and Updated Lagrangian (UL). Numerical study consists of installation process, consolidation phase and following pile static load test (SLT). The Poznań site is chosen as the reference location for the numerical analysis, where series of pile SLTs...
-
Screw displacement pile shaft deformations measured by vibrating wire and fiber optic systems during a static load test
PublicationThis paper describes a full scale static load test performed on a 400 mm diameter screw displacement pile equipped with four different strain measuring systems. Three types of vibrating wire strain gauges (VWSG) were used: global - retrievable, local attached to steel pipe and local concrete embedded. The fourth system was distributed fiber optic sensors based on Rayleigh back scattering (DFOS) - three in the pile cross section....
-
The influence of stainless steels microstructure evolution on the mechanical properties of pressure installation elements
PublicationIn this paper results of FEM analysis performed for pipe and 90o elbow, made of super duplex stainless steel, after precipitation of sigma phase (),were presented. Heat treatment conditions simulate accidental overheating that can occur in nuclear installations after cooling circulation fails. For initial and modified microstructure tensile test was performed and numerical description of work hardening curves was done. Verification...
-
The influence of stainless steels microstructure evolution on the mechanical properties of pressure installation elements
PublicationIn this paper results of FEM analysis performed for pipe and 90o elbow, made of super duplex stainless steel, after precipitation of sigma phase (s), were presented. Heat treatment conditions simulate accidental overheating that can occur in nuclear installations after cooling circulation fails. For initial and modified microstructure tensile test was performed and numerical description of work hardening curves was done. Verification...
-
Noise and Rolling Resistance Properties of Various Types of Winter Tyres Compared to Normal Car Tyres
PublicationTo cope with winter weather conditions, potentially including snow and ice, it is common to use winter tyres, or ”all-seasons” tyres assumed to be safe both in summer and winter. In some northern countries, winter tyres are mandatory. Traditionally, it has been assumed that winter tyres are noisier than normal tyres (here called summer tyres) and winter tyres equipped with studs are assumed to be very noisy.This paper presents...
-
ANALYSIS OF ROLLING RESISTANCE OF TIRES WITH RUN FLAT INSERT APPLYING DRUM METHOD AND RADIAL CHARACTERISTIC
PublicationThis paper presents analysis of rolling resistance of tires with RUN FLAT insert applying drum method and radial characteristic. The conducted studies indicated changes in operational properties of wheel, occurring as a result of inflation pressure drop in the wheel. As regards radial elasticity, such changes result in significant drop of radial rigidity and increase of static deflection and increase of tire rolling resistance....
-
The features of steel surface hardening with high energy heating by high frequency currents and shower cooling
Publication -
Looking for New Ideas of Public Space - Public Space Projects in Gdansk Reinforced by Art Activities
Publication -
Looking for New Ideas of Public Space – Public Space Projects in Gdansk Reinforced by Art Activities
PublicationRevitalization of public open spaces is a complex enterprise in Poland in terms of the art, cultural andinformation aspects of this process. Simultaneously the public space should play an important role whenbuilding the quality of revitalization programs and the quality of city development. The new art and culturalactivities are the revitalization tools, which are also the good examples of bottom up ideas helping to start aprocess...
-
Influence of the engine cooling down period during short car stops on the average fuel consumption
PublicationW publikacji przedstawiono wpływ schłodzenia silnika podczas krótkich postojów pomiędzy jazdami na średnie zużycie paliwa. Przeprowadzono własne pomiary w czasie jazd miejskich w Gdańsku. Użyto samochodu osobowego z silnikiem o objętości skokowej 2 dm^3 z zapłonem siskrowym. Mierzono zużycie paliwa na trasach o długości 3-10 km. Krótko opisano sposoby wstępnego podgrzania silnika przed rozruchem.
-
Heat transfer to car engine cooling system - influence of coolant flow through engine block
PublicationW artykule przedstawiono wyniki badań doświadczalnych nad wpływem nastawianej wydajności pompy cieczy na strumień odbieranego ciepła w silniku spalinowym. Wykorzystano hamownię silnikową z silnikiem o zapłonie iskrowym o objętości skokowej 1.8 dm^3. Przyjęto obciążenia silnika oporami ruchu samochodu na biegu bezpośrednim.
-
The influence of type of dispersed phase on rolling contact fatigue of lubricating greases on mineral base oil
Publication -
Hybrid super‐twisting fractional‐order terminal sliding mode control for rolling spherical robot
Publication -
Modelowanie asymetrycznego procesu walcowania blach bimetalowych = The modeling of asymetrical rolling process of bimetallic plate
PublicationW pracy rozważano problem płynięcia plastycznego bimetalowego pasma podczas asymetrycznego procesu walcowania blach bimetalowych. Asymetrię procesu uzyskano w wyniku wprowadzenia różnic w wartościach sił tarcia na powierzchniach styku pasma z poszczególnymi walcami.
-
Implementation of Fluidized Bed Concept to Improve Heat Transfer in Ecological Adsorption Cooling and Desalination Systems
Publication -
Organic Rankine cycle turbogenerator cooling – Optimization of the generator water jacket heat exchange surface
Publication -
Relieving the Measuring System of the Trailer for Tyre/Road Rolling Resistance Measurements from the Inertia Force
PublicationIn the article the principle of measuring of tyre/road rolling resistance tyres in road conditions applied in a special measuring trailer is presented. This trailer was built in Faculty of Mechanical Engineering at Gdansk University of Technology. The construction of two special devices used in this trailer was discussed. These devices eliminate the influence of some chosen confounding measurements factors such as: the inertia...
-
Structural and Microhardness Changes After Turning of the AISI 1045 Steel for Minimum Quantity Cooling Lubrication
Publication -
Study on Technological Effects of a Precise Grooving of AlSi13MgCuNi Alloy with a Novel WCCo/PCD (DDCC) Inserts
Publication -
Scuffing and rolling contact fatigue resistance of discrete laser spot hardened austempered ductile iron
Publication -
Improvement of machinability of Ti and its alloys using cooling-lubrication techniques: a review and future prospect
Publication -
A new modelling arrangement for testing of Catenary Anchoring Leg Mooring (CALM) system behaviour in waves
PublicationW artykule przedstawiono układ modelowy pławy cumowniczo-przeładunkoweji łańcuchów kotwicznych możliwy do realizacji w wydłużonych basenach falowych służących na co dzień do badania właściwości morskich statków. System łańcuchów kotwicznych sprowadzono do płaszczyzn równoległych do osi basenu i połączono z pławą cienkimi linkami stalowymi przechodzącymi przez bloczki kierunkujące. Opisywany układ pozwolił na przeprowadzenie badań...
-
Collision‐Aware Routing Using Multi‐Objective Seagull Optimization Algorithm for WSN‐Based IoT
PublicationIn recent trends, wireless sensor networks (WSNs) have become popular because of their cost, simple structure, reliability, and developments in the communication field. The Internet of Things (IoT) refers to the interconnection of everyday objects and sharing of information through the Internet. Congestion in networks leads to transmission delays and packet loss and causes wastage of time and energy on recovery. The routing protocols...
-
Looking for the Optimal Location of an Eco-District within a Metropolitan Area: The Case of Tricity Metropolitan Area
PublicationCompact housing structures located in city centers are considered to be the most energy and environmentally eective, mainly due to the access to services, transport networks and municipal infrastructures. There is the question of why so many of the acknowledged ecological housing complexes are located on the outskirts of cities or suburbs. Numerous cities decide to introduce strategies either to densify city centers, hoping to...
-
A Quantitative Investigation of Dislocation Density in an Al Matrix Composite Produced by a Combination of Micro-/Macro-Rolling
PublicationAn aluminum matrix composite with dispersed carbon nanotubes (CNTs) was produced via flake powder metallurgy using a micro-rolling process and vacuum hot pressing (VHP), followed by conventional rolling using a macro-rolling process. The microstructure and mechanical properties of the produced composites were studied. In addition, a new quantitative model was introduced to study the dislocation density based on the microstructural...
-
Spatial variability of throughfall in a stand of Scots pine (Pinus sylvestris L.) with deciduous admixture as influenced by canopy cover and stem distance
PublicationVegetation cover affects the amount of precipitation, its chemical composition and its spatial distribution, and this may have implications for the distribution of water, nutrients and contaminants in the subsurface soil layer. The aim of this study was a detailed diagnosis of the spatio-temporal variability in the amount of throughfall (TF) and its chemical components in a 72-year-old pine stand with an admixture of oak and birch....
-
Distinctive properties of Scots pine (Pinus sylvestris L.) originating from the Carpathian and Great Poland-Pomeranian of Nature and Forest Land
PublicationIn this paper values of properties of Scots pine, the fracture toughness and of shear yield stress in the shear zone are presented. Samples of Scotch pine (Pinus sylvestris L.) wood of two provenances from Poland were tested. These properties were determined from the values of cutting power obtained experimentally on the saw frame PRW-15M. The values of fracture toughness and shear yield stress based on the Atkins model for cutting...