Search results for: MODULACJA AMPLITUDY
-
The instantaneous frequency rate spectogram
PublicationAn accelerogram of the instantaneous phase of signal components referred to as an instantaneous frequency rate spectrogram (IFRS) is presented as a joint time-frequency distribution. The distribution is directly obtained by processing the short-time Fourier transform (STFT) locally. A novel approach to amplitude demodulation based upon the reassignment method is introduced as a useful by-product. Additionally, an estimator of energy...
-
A nine-input 1.25 mW, 34 ns CMOS analog median filter for image processing in real time
PublicationIn this paper an analog voltage-mode median filter, which operates on a 3 × 3 kernel is presented. The filter is implemented in a 0.35 μm CMOS technology. The proposed solution is based on voltage comparators and a bubble sort configuration. As a result, a fast (34 ns) time response with low power consumption (1.25 mW for 3.3 V) is achieved. The key advantage of the configuration is relatively high accuracy of signal processing,...
-
Analysis of spontaneous electrochemical oscillations by energy distribution technique
PublicationAnaliza niestacjonarnych oscylacji elektrochemicznych wskazuje na konieczność stosowania technik umożliwiających śledzenie zmian w czasie takich parametrów oscylacji jak częstotliwość, amplituda, pasmo częstotliwościowe. Algorytm prowadzący do uzyskania tych parametrów może być oparty o jeden z liniowych lub kwadratowych sposobów przedstawienia rejestru oscylacji w dziedzinie czasu i częstotliwości. W pracy autorzy przedstawiają...
-
Novel Interpolation Method of Multi-DFT-Bins for Frequency Estimation of Signal with Parameter Step Change
PublicationThe IpDFT(Interpolation Discrete Fourier Trans-form) method is one of the most commonly used non-parametric methods. However, when a parameter (frequency, amplitude or phase) step changes in the DFT period, the DFT coefficients will be distorted seriously, resulting in the large estimation error of the IpDFT method. Hence, it is a key challenge to find an IpDFT method, which not only can eliminate the effect of the step-changed...
-
Receiver of Doppler multistatic system for moving target detection and tracking
PublicationThe article presents a method for solving major structural problems that occur in the receiver used in the multistatic Doppler system, aimed at determination of the trajectory and velocity of a moving target. In the system two transmitters emit acoustic continuous sinusoidal waves at different frequencies. The signals, scattered from a moving target are received by four hydrophones. Beside of the echoes, much larger signals coming...
-
SONIC - Self-optimizing narrowband interference canceler: comparison of two frequency tracking strategies
PublicationThis paper presents a new approach to rejection of complex-valued sinusoidal disturbances acting at the output of a discrete-time linear stable plant with unknown and possibly time-varying dynamics. It is assumed that both the instantaneous frequency of the sinusoidal disturbance and its amplitude may be slowly varying with time and that the output signal is contaminated with wideband measurement noise. The proposed disturbance...
-
Comparison of the exponential thermal transient parameterization methods with the SMTP method in the unipedicled DIEP flap computer modelling and simulation
PublicationThe aim of this paper is to compare the spatial contrast of the image descriptors obtained via three different thermal transient parameterization methods in Active Dynamic Thermography. The thermal constants and amplitude values of the one- and two- exponential parametrization are compared to the Simplified Magnitude-Temporal Parametrization method (SMTP). The comparison is performed using the data obtained by simulating the cold...
-
Fluctuation-Enhanced Sensing for Biological Agent Detection and Identification
PublicationPrzedstawiono wcześniejsze wyniki badań dotyczące trzech różnych sposobów wykrywania obecności substancji biologicznych za pomocą zjawisk fluktuacyjnych: 1) wirusów wnikających do komórek, 2) zapachów emitowanych przez mikroby, 3) rozkładu widma i wartości chwilowych szumów podczas rozpraszania światła używanego do wykrywania zarodników na podstawie wyznaczenia współczynnika dyfuzji opisująceo ich ruch.We survey and show our earlier...
-
Broken rotor symptoms in the sensorless control of induction machine
PublicationThe purpose of this paper is to investigate the need for a universal method for sensorless controlled induction motor drive diagnosis. The increasing number of sensorless control systems in industrial applications require a universal method for the drive diagnosis, which provides reliable diagnostic reasoning independent of control system structure and state variables measurement or estimation method.Simulations and experimental...
-
On the Handling of Outliers in the GNSS Time Series by Means of the Noise and Probability Analysis
PublicationThe data pre-analysis plays a significant role in the noise determination. The most important issue is to find an optimum criterion for outliers removal, since their existence can affect any further analysis. The noises in the GNSS time series are characterized by spectral index and amplitudes that can be determined with a few different methods. In this research, the Maximum Likelihood Estimation (MLE) was used. The noise amplitudes...
-
Application of Illuminating Modes concept in modal expansion of elliptical resonator
PublicationIn the paper an IlluminatingModes (IM) approach as an extension of Spectral Domain Approach (SDA) is presented. IM concept is applied to the case of open microstrip planar elliptical resonator. A modal expansion of currents induced in the structures during illuminating them by a single plane wave is the novelty of the method. As an example of application of the method, we present the results obtained by an examination of two resonators...
-
Generowanie składowej zerowej w układzie z filtrem wyjściowym falownika napięcia
PublicationW referacie przedstawiono analizę metod sterowania falownikiem napięcia pod kątem generowania składowej zerowej w przebiegu wyjściowym napięcia. Wskazano metody, w których składowa zerowa powstaje w rezultacie dodawania trzeciej harmonicznej i jej wielokrotności do przebiegów napięć fazowych w celu zwiększenia możliwości generowania podstawowej harmonicznej. Pokazano, że składowa zerowa generowana jest w każdej metodzie sterowania...
-
Dobór parametrów pomiaru cyfrowego profili i jego następstwa w analizie amplitudowo-częstotliwościowej nierówności powierzchni
PublicationAnaliza pomiaru cyfrowych nierówności profili jest złożonym problemem interdyscyplinarnym, którego parametry powinny uwzględniać ich charakter i cele postawione dla badanych nierówności powierzchni. Normatywne wysokościowe ujęcia nierówności oraz długościowe, punktowe i inne parametry nie oddają jednoznacznie cech powierzchni, dlatego też poznawcze i badawcze analizy profili powinny być prowadzone funkcjami amplitudowo-częstotliwościowymi...
-
Comparison of effectiveness of musical sound separation algorithms employing neural networks.
PublicationNiniejszy referat przedstawia kilka algorytmów służących do separacji dźwięków instrumentów muzycznych. Zaproponowane podejście do dekompozycji miksów dźwiękowych opiera się na założeniu, że wysokość dźwięków w miksie jest znana, tzn. wejściem dla algorytmów jest przebieg zmian wysokości dźwięków składowych miksu. Proces estymacji fazy i amplitudy składowych harmonicznych wykorzystuje dopasowywanie zespolonych przebiegów harmonicznych...
-
Comparative study on fracture evolution in steel fibre and bar reinforced concrete beams using acoustic emission and digital image correlation techniques
PublicationIn recent decades, the demand for sustainable construction practices has increased, but raw materials such as reinforcing steel remain scarce. Therefore, steel fibres have emerged as a popular and sustainable choice in the construction industry, offering a cost-effective alternative to traditional steel bar reinforcement for both flatwork and elevated structures. The purpose of this study is therefore to compare the performance...
-
Investigation of long-range dependencies in the stochastic part of daily GPS solutions
PublicationThe long-range dependence (LRD) of the stochastic part of GPS-derived topocentric coordinates change (North, East, Up) results with relatively high autocorrelation values with a focus on self-similarity. One of the reasons for such self-similarity in the GPS time series are noises that are commonly recognised to prevail in the form of the flicker noise model. To prove the self-similarity of the stochastic part of GPS time series...
-
Testing HIADAC high impedance analyzer in cooperation with Road and Bridge Research Institute on polyvinyl coating using 2-wire probe sample 1
Open Research DataThe dataset presents impedance spectrum of polyvinyl coating (code-name PW_2_2_1) sample 1. This object was used to test high-impedance analyzer for diagnostic of anticorossion coatings (HIADAC) realized in the frame of Eureka project E!3174. The impedance spectrum frequency range (0.1 Hz – 100 kHz) was selected in order to test the whole measureement...
-
Testing HIADAC high impedance analyzer in cooperation with Road and Bridge Research Institute on polyvinyl coating using 2-wire probe sample 2
Open Research DataThe dataset presents impedance spectrum of polyvinyl coating (code-name PW_2_2_1) sample 2. This object was used to test high-impedance analyzer for diagnostic of anticorossion coatings (HIADAC) realized in the frame of Eureka project E!3174. The impedance spectrum frequency range (0.1 Hz – 100 kHz) was selected in order to test the whole measureement...
-
Testing HIADAC high impedance analyzer in cooperation with Road and Bridge Research Institute on nano-nickel based coating using 2-wire probe sample 2
Open Research DataThe dataset presents impedance spectrum of nano-nickel based coating sample 2. This object was used to test high-impedance analyzer for diagnostic of anticorossion coatings (HIADAC) realized in the frame of Eureka project E!3174. The impedance spectrum frequency range (0.1 Hz – 100 kHz) was selected in order to test the whole measureement range of...
-
Testing high impedance analyzer in the field on high-voltage line pylon cell 1 exposition 2
Open Research DataThe dataset presents impedance spectrum of anticorrosion coating on high-voltage line pylon presented in the figure below. This object was used to test high-impedance analyzer for diagnostic of anticorossion coatings (HIADAC) realized in the frame of Eureka project E!3174. The dataset contains comparative measurements with Atlas-Sollich ATLAS98HI analyser....
-
Testing high impedance analyzer in the field on high-voltage line pylon cell 1 exposition 1
Open Research DataThe dataset presents impedance spectrum of anticorrosion coating on high-voltage line pylon presented in the figure below. This object was used to test high-impedance analyzer for diagnostic of anticorossion coatings (HIADAC) realized in the frame of Eureka project E!3174. The dataset contains comparative measurements with Atlas-Sollich ATLAS98HI analyser....
-
Testing HIADAC high impedance analyzer in cooperation with Road and Bridge Research Institute on nano-nickel based coating using 2-wire probe sample 1
Open Research DataThe dataset presents impedance spectrum of nano-nickel based coating sample 1. This object was used to test high-impedance analyzer for diagnostic of anticorossion coatings (HIADAC) realized in the frame of Eureka project E!3174. The impedance spectrum frequency range (0.1 Hz – 100 kHz) was selected in order to test the whole measureement range of...
-
Testing high impedance analyzer in the field on high-voltage line pylon cell 2 exposition 1
Open Research DataThe dataset presents impedance spectrum of anticorrosion coating on high-voltage line pylon presented in the figure below. This object was used to test high-impedance analyzer for diagnostic of anticorossion coatings (HIADAC) realized in the frame of Eureka project E!3174. The dataset contains comparative measurements with Atlas-Sollich ATLAS98HI analyser....
-
Wideband Off-Body Channel Characteristics with Dynamic User
PublicationThis paper presents the preliminary results of a dynamic off-body channel characterisation study, based on wideband measurements at 5.8 GHz in an indoor environment. The Channel Impulse Response (CIR) was measured for a scenario with the user approaching and departing from the off-body antenna. A CIR deconvolution procedure was performed jointly in two polarisations, and the received signal power, Cross-Polarisation Discrimination...
-
Generalized adaptive notch smoothers for real-valued signals and systems
PublicationSystems with quasi-periodically varying coefficients can be tracked using the algorithms known as generalized adaptive notch filters (GANFs). GANF algorithms can be considered an extension, to the system case, of classical adaptive notch filters (ANFs). We show that estimation accuracy of the existing algorithms, as well as their robustness to the choice of design parameters, can be considerably improved by means of compensating...
-
The influence of the local pipeline leak on water hammer properties
PublicationPrzedstawiono wyniki eksperymentalnej i numerycznej analizy zjawiska uderzenia hydraulicznego. Pomiary przeprowadzono dla przewodu MDPE o długości 36 m, w którym zamodelowano lokalną nieszczelność. W tym celu, w pewnej odległości od zaworu umieszczonego na końcu przewodu zainstalowano kształtki imitujące lokalny wyciek. Przeprowadzono analizę otrzymanych charakterystyk ciśnienia i wyznaczono parametry: okres oscylacji, amplitudę...
-
POSSIBILITY OF IDENTIFICATION OF TECHNICAL CONDITION OF BEARINGS FOR SELF-IGNITION ENGINES BY APPLICATION OF ACOUSTIC EMISSION AS A DIAGNOSTIC SIGNAL
PublicationThis paper presents the results of empirical studies where the acoustic emission (AE) method was applied to identify the technical condition of sliding surfaces of main and crank bearings for main diesel engines. The test results indicate that the measurements of the AE parameters allow the technical condition identification for bearings of this type. The results refer to the measurements of the parameters for AE generated in the...
-
Positron scattering on molecular hydrogen: Analysis of experimental and theoretical uncertainties
PublicationExperiments performed in recent years on positron scattering from molecular hydrogen indicated a rise of the total cross section in the limit of zero energy, but essentially disagree on the amplitude of this rise. Mitroy and collaborators [J.-Y. Zhang et al., Phys. Rev. Lett. 103, 223202 (2009)] predicted a scattering length somewhat different from values deduced experimentally. Using a Markov chain Monte Carlo modified effective...
-
Low cost microwave X-band generator
PublicationA low cost microwave X-band generator for educational purposes was designed and built. Its simple construction and user's interface makes it suitable for a student laboratory.The generator is based on a single frequency conversion concept. It uses a digitally tunable PLL chip for intermediate frequency generation and an active frequency multiplier for frequency conversion. The generator covers 9,7 - 11 GHz part of the X frequency...
-
Ocena wykrywalności modelowych wad wąskoszczelinowych metodą pomiaru przestrzennego rozkładu magnetycznego pola rozproszonego
PublicationWykazano, że metoda pomiaru natężenia metodą pomiaru natężenia pola rozproszonego (MPR) w polu szczątkowym umożliwia skuteczne wykrywanie zewnętrznych wad szczelinowych o głębokościach 0,2 mm przy długości 2,5 mm, oraz wad punktowych o średnicy mniejszej od 1mm i głębokości 0,3 mm. Zwiększenie poziomu namagnesowania (pomiary w pełnym polu magnetycznym) umożliwiło wykrywanie wad o znacznie mniejszych rozmiarach. Wykazano również,...
-
Fluctuation-Enhanced Sensing of Organic Vapors by Ink-Printed MoS2 Devices under UV Irradiation
PublicationThis work presents the results of fluctuationenhanced sensing (FES) of selected organic gases by MoS2 sensor fabricated via a simple ink printing method. We demonstrate that low-frequency noise measured under UV irradiation (275 nm) is more sensitive to different gases than measured in the dark. The noise at 1 Hz under UV light increased 3.3, 3.5, 1.6, and 2.9 times for chloroform, tetrahydrofuran, acetonitrile, and acetone ambiances, respectively....
-
Badania wykrywalności wad sztucznych w rurach impulsami akustycznymi, wzbudzanymi metodą magnetostrykcyjną
PublicationW artykule opisano wyniki badań nad oryginalną metodą detekcji wad w rurach, wykorzystującą efekty magnetosprężyste. Stanowi to kolejny etap badań rozwijania metody generacji impulsów magnetostrykcyjnych. W pracy przedstawiliśmy wyniki prac badawczych nad układem defektoskopu wykorzystującego metodę generacji akustycznych impulsów magnetostrykcyjnych. W badaniach wykorzystano trzy sztuczne wadyw rurze w kształcie otworów oraz nacięcia...
-
Modeling of a rock fall using the discrete element method and study of the seismic signal
PublicationMechanizm dużego spadającego bloku skalnego lub lawiny pozostaje nadal słabo rozpoznany zarówno w zakresie pęknięć jak i procesów propagacji. Jedynie ilościowe dane, które aktualnie są mierzone i uchwytne podczas spadania skały, zarejestrowane są jako sejsmiczne sygnały przez szereg sejsmografów. Właściwości sygnału (amplituda, trwanie, częstotliwość) są wyraźnie powiązane z cechami spadania (masa, wysokość spadania, odległość...
-
Method of Monitoring of the Grinding Process with Lapping Kinematics Using Audible Sound Analysis
PublicationUtilising microphones as audible sound sensors for monitoring a single-side grinding process with lapping kinematics is presented in the paper. The audible sound generated during grinding depended on the cutting properties of electroplated tools with D107 diamond grains and different thicknesses of the nickel bond. The tool wear affected the obtained technological effects such as material removal rate and the surface roughness...
-
Effect of waviness and roughness components on transverse profiles of turned surfaces
PublicationThis paper presents the authors method of simultaneous analysis of roughness and waviness irregularity components, with the aim of better defining the key qualities and characteristics.Periodical surface machining traces may be analyzed spectrally, with the irregularity's peaks and troughs being used to define the wave's amplitude.In this work the standard composition for filtering waviness and roughness components of a surface...
-
Compact 4 × 4 butler matrix with non‐standard phase differences for IoT applications
PublicationButler matrices represent a popular class of feeding networks for antenna arrays. Large dimensions and the lack of flexibility in terms of achievable output phase difference make conventional Butler structures of limited use for modern communication devices. In this work, a compact planar 4 × 4 matrix with non-standard relative phase shifts of –30º, 150º, –120º, and 60º has been proposed. The structure is designed to operate at...
-
Effect of manufacturing errors of the pad sliding surface on the performance of the hydrodynamic thrust bearing
PublicationIn the present study, investigation of the effect of manufacturing errors on the performance of large tilting pad thrust bearings has been performed, following a CFD-based Thermohydrodynamic analysis of a single pad. A 3D model has been generated, including the pad, the lubricant film and the corresponding part of the collar. The pad has been assumed to be deformed about the pivot point, due to thrust loading. Manufacturing errors...
-
Electron interactions with Bis(pentamethylcyclopentadienyl) titanium(IV) dichloride and difluoride
PublicationWe present a combined experimental and theoretical study of the interaction of electrons with Bis(pentamethylcyclopentadienyl)titanium(IV) dichloride (Cp∗2TiCl2) and difluoride (Cp∗2TiF2). We report the experimental measurements of partial cross sections for the dissociative electron attachment (DEA) and the electron ionization (EI) mass spectra of isolated molecules. Estimates of the absolute cross sections are done on the basis...
-
Expedited Design Closure of Antennas By Means Of Trust-Region-Based Adaptive Response Scaling
PublicationIn the letter, a reliable procedure for expedited design optimization of antenna structures by means of trust-region adaptive response scaling (TR-ARS) is proposed. The presented approach exploits two-level electromagnetic (EM) simulation models. A predicted high-fidelity model response is obtained by applying nonlinear frequency and amplitude correction to the low-fidelity model. The surrogate created this way is iteratively rebuilt...
-
Obliczenia niezawodności użytkowej kładek dla pieszych
PublicationW pracy zaprezentowano metodę obliczania niezawodności użytkowej kładek dla pieszych. Obciążenie pieszymi opisano definiując następujące zmienne losowe: amplitudę i częstość wymuszenia pieszego, jego prędkość, a także czas i miejsce pojawienia się na kładce. Zastosowano metodę Monte Carlo. Wygenerowane realizacje obciążenia stanowią zbiór danych wejściowych do obliczeń przeprowadzanych dowolnym programem stosującym metodę elementów...
-
Diagnostyka łożysk silnika indukcyjnego z wykorzystaniem analizy prądu silnika metodą potrójnej kowariancji.
PublicationPrzedmiotem niniejszej rozprawy doktorskiej jest opracowanie nowej metody diagnostyki łożysk w silniku indukcyjnym opartej na pomiarach i analizie prądu zasilającego silnik. Ze względu na ciągłe doskonalenie i rozwój badao w kierunku metod prądowych, za pomocą których możliwa byłaby diagnostyka całego silnika, temat ten jest cały czas otwarty i jak najbardziej aktualny. Rozdział pierwszy zawiera wprowadzenie w zagadnienia będące...
-
Error analysis for European IGS stations
PublicationEach of the GPS time series that describes the changes of topocentric components consists of a deterministic and a stochastic part, whose character influences the errors of the deterministic parameters. As to the uncertainties of reliable velocities of permanent satellite station systems, surveys that estimate and take into account any dependencies that may affect subsequent operational efficiency are very important. For this analysis,...
-
The Rayleigh model of the multipath fading channel
Open Research DataThe dataset contains the results of simulations that are part of the research on modelling the multipath fading in the communication channel. The Rayleigh fading envelope is generated using the Monte-Carlo simulation (MCS) in the LabVIEW programming environment.
-
The α-µ model of the multipath fading channel
Open Research DataThe dataset contains the results of simulations that are part of the research on modelling the multipath fading in the communication channel. The envelope of the α-µ fading process is generated using the Monte-Carlo simulation (MCS) in the LabVIEW programming environment.
-
Technika bezprzewodowa w automatyce - 2021/2022
e-Learning CoursesCel przedmiotu:Poznanie budowy i działania łącza radiowego i jego głównych zastosowań w automatyce Treść przedmiotu: 1. Wprowadzenie do łączności bezprzewodowej, funkcje części nadawczej i odbiorczej, schemat funkcjonalny łącza radiowego, skrótowy zapis fali radiowej 2. Podstawowe zależności energetyczne w części bezprzewodowej łącza radiowego, powierzchniowa gęstość mocy, natężenie pole elektrycznego 3. Nadajnik radiowy, układ...
-
Wykorzystanie zespolonej pulsacji chwilowej do ślepej synchronizacji symbolowej sygnałów QPSK
PublicationIzochronicznie nadawane i synchronicznie odbierane sygnały QPSK (z ang. Quadrature Phase-Shift Keying) dominują w dzisiejszej radiowej i przewodowej telekomunikacji cyfrowej. Poprawne działanie odbiornika sygnałów QPSK wymaga skomplikowanego systemu synchronizacji poszczególnych etapów odbioru. W skład systemu synchronizacji odbiornika wchodzi odtwarzanie częstotliwości i fazy sinusoidy (fali) nośnej oraz wyznaczanie chwil próbkowania...
-
Hydroacoustic ships berthing aid systems in Gdańsk north harbour
PublicationManewry dobijania statków do nabrzeży portowych są trudnymi operacjami, przy których należy uwzględniać m. in. na pływy, wiatry, widzialność, prędkość, masę statku, odległość od pirsu. Ewentualna kolizja z pirsem niesie poważne konsekwencje, szczególnie groźne dla wielkich statków a zwłaszcza tankowców. Referat prezentuje hydroakustyczne systemy kontroli manewrów statków wykonane przez zespół pracowników Katedry Systemów Elektroniki...
-
Testing HIADAC high impedance analyzer in cooperation with Road and Bridge Research Institute on epoxy based coating using 2-wire probe sample 2
Open Research DataThe dataset presents impedance spectrum of epoxy based coating (code-name B2_B3) sample 2. This object was used to test high-impedance analyzer for diagnostic of anticorossion coatings (HIADAC) realized in the frame of Eureka project E!3174. The impedance spectrum frequency range (0.1 Hz – 100 kHz) was selected in order to test the whole measureement...
-
Testing high impedance analyzer in the field on high-voltage line pylon cell 2 exposition 2
Open Research DataThe dataset presents impedance spectrum of anticorrosion coating on high-voltage line pylon presented in the figure below. This object was used to test high-impedance analyzer for diagnostic of anticorossion coatings (HIADAC) realized in the frame of Eureka project E!3174. The dataset contains comparative measurements with Atlas-Sollich ATLAS98HI analyser....
-
Testing HIADAC high impedance analyzer in cooperation with Road and Bridge Research Institute on epoxy based coating using 2-wire probe sample 1
Open Research DataThe dataset presents impedance spectrum of epoxy based coating (code-name B2_B3) sample 1. This object was used to test high-impedance analyzer for diagnostic of anticorossion coatings (HIADAC) realized in the frame of Eureka project E!3174. The impedance spectrum frequency range (0.1 Hz – 100 kHz) was selected in order to test the whole measureement...